Use and Care Manual

ManualsBrandseSenLite ManualsCeiling Light PartsWall Mount 2.4G RF Dimmer CCT Selector and 2-Way Switcher Tri-Function AC Power Controller for LED Panel Light EEFPTL

Single-Multi way

1. Line (Hot)

2. Neutral

3. Ground

4. First load

5. Second load

Multi switch-single way

1. Line (Hot)

2. Neutral

3. Ground

4. First load

5. other switch

(regular switch or

this product )

Single-Pole

1. Line (Hot)

2. Neutral

3. Ground

4. Load

Step 2

Identifying your wiring application

(most common):

NOTE: If the wiring in the wall box does not

resemble any of these conﬁgurations, consult an

electrician.

Cat. No. 2ATWWJKX-TWWR

Model: EEFPTL-ACRC-W

2.4G Wall Type Wireless Dimming & CCT Tunable Dimmer

1200W-120Vac, 60Hz, 1500W-277Vac, 50Hz

Only suitable for driver of 2.4G wireless CCT tunable LED fixtures produced by E E Systems Group, Inc.

INSTALLATION INSTRUCTIONS

WARNINGS AND CAUTIONS:

• To avoid fire, shock, or death; turn off power at circuit breaker or fuse and test that power is off before wiring

E E Systems Group, Inc.

12346 Valley Blvd, Suite A

El Monte, CA 91732 USA

Info@eesgi.com;

1-877-579-3889 Mon.-Fri. 10am-5pm PST

or servicing fixture!

• To be installed and/or used in accordance with appropriate electrical codes and regulations.

• If you are unsure about any part of these instructions, consult an electrician.

WARNINGS AND CAUTIONS:

• Use one dimmer in a 3- or 4-way circuit.The switch(es) will turn the light on at the brightness level selected at the dimmer.

•

• Use this device only with copper or copper clad wire.

Lighting fixture and dimmer must be grounded.

Tools needed to install your Dimmer

Slotted / Screwdriver Electrical Tape Pliers

Pencil Cutters Ruler

Installing Dimmer by itself or with other devices

If installing Dimmer in a single device application, proceed

with the INSTALLING YOUR DIMMER section. If installing

Dimmer in a multi-device application, proceed as follows:

Your Dimmer includes three color options. The Dimmer

ships with the White frame attached. To change color of

frame, proceed as follows:

Changing the color of your Dimmer

Push in side at tab

to release

Line up tabs and

press in side to attach

Note: Move slider on dimmer and slider on change kit

to bottom of the slide bar prior to engaging.

MULTI-DEVICE APPLICATION:

NOTE: You only need to remove side sections if installing

with other dimmers or if it does not ﬁt in wall box – not

when installing with mechanical switches.

When installing more than one dimmer in the same

location, the side sections of the mounting strap must be

removed. Use pliers to carefully bend side sections back

and forth until they break off.

Bend back and

forth to remove side

section

Remove

all inner

side

sections

Do not

remove

outer

side

sections

WARNING: TO AVOID FIRE, SHOCK, OR

DEATH; TURN OFF POWER at circuit breaker or

fuse and test that power is off before wiring!

ONOFF

ONOFFONOFF

ONOFF

Step 1

Two

Gang

More than

Cat. No.

Volts

Single

2 Devices

2ATWWJKX-TWWR

120 1200VA 1200VA 1200VA

277 1500VA 1500VA 1500VA

MAXIMUM LOAD PER DIMMER FOR MULTI-DEVICE

Note: No derating is required in this mult-device installation

as referenced in the following chart.

MAXIMUM BULB WATTAGE:

The maximum number of loads per dimmer is based on the

sum of the load ratings. For example, one dimmer can carry

a maximum of 24pcs 50W LED fixtures when the voltage is

120Vac; when the voltage is 277Vac, a maximum of 30 can

be carried.

√

INSTALLING YOUR DIMMER

NOTE: Use check boxes when Steps are completed.

Step 4A

Step 3

Preparing wires:

• Pull off pre-cut insulation from Dimmer leads.

• Make sure that the ends of the wires from the wall

box are straight (cut if necessary) .

• Remove 5/8" (1.6 cm) of insulation from each wire

in the wall box (shown).

• For Single-Pole Application, go to Step 4A.

• For 3-Way Application, go to Step 4B.

Strip Gage

5/8"

(1.6 cm)

Cut

(if necessary)

Strip 5/8"

(1.6 cm)

Insert wires

straight then twist

clockwise

Electrical Tape

Ground

Neutral

Black

Red

White

Red

This wire is used in 3-way installations only.

For single pole installations, do not remove this

insulating label.

Single-Pole Wiring Application:

Connect wires per WIRING DIAGRAM 1 (shown on

page 2) as follows:

Screwing wire nuts on clockwise ensures no bare

conductors showed below the wire connectors.

Secure each connector with electrical tape.

Step 4B

Single-Multi way Application:

NOTE:

Connect the ground wire of the fixture to the ground

wire in the line.

Connect the black wire of this product to the live wire

in the wire.

Connect the white wire of this product to the neutral

wire in the line.

Connect the red line marked with output to the load in

the line.

The remaining red lines are not connected

Connect wires per WIRING DIAGRAM 1 (shown on

page 2) as follows:

Screwing wire nuts on clockwise ensures no bare

conductors showed below the wire connectors.

Secure each connector with electrical tape.

NOTE:

Connect the ground wire of the fixture to the ground

wire in the line.

Connect the black wire of this product to the live wire

in the wire.

Connect the white wire of this product to the neutral

wire in the line.

Connect the red line marked with output to the all load

in the line.

The remaining red lines are not connected

Insert wires

straight then twist

clockwise

Electrical

Tape

Ground

Neutral

Black

Red

White

Red

This wire is used in 3-way installations only.

For single pole installations, do not remove this

insulating label.

Step 4C

Multi switch-single way Application:

This wire is used in 3-way installations only.

For single pole installations, do not remove this

insulating label.

Other switch

Connect wires per WIRING DIAGRAM 1 (shown on

page 2) as follows:

Screwing wire nuts on clockwise ensures no bare

conductors showed below the wire connectors.

Secure each connector with electrical tape.

NOTE:

Connect the ground wire of the fixture to the ground

wire in the line.

Connect the black wire of this product to the live wire

in the wire.

Connect the white wire of this product to the neutral

wire in the line.

Connect the red line marked with output to the load

in the line.

Connect the remaining red wire to another switch.

Insert wires

straight then twist

clockwise

Electrical Tape

Ground

Neutral

Black

Red

White

Red

IMPORTANT: When single control single pole and single control

multi-way, connect the load line to the red line of this product

whose label marked with “output”.

When multi control single way, connect the load line to the red

line of this product whose label marked with “output”, and

connect the other switch lineto another red line of this product.

Summary of content (2 pages)

PAGE 1
2.4G Wall Type Wireless Dimming & CCT Tunable Dimmer Cat. No. 2ATWWJKX-TWWR E E Systems Group, Inc. 1200W-120Vac, 60Hz, 1500W-277Vac, 50Hz 12346 Valley Blvd, Suite A Only suitable for driver of 2.4G wireless CCT tunable LED fixtures produced by E E Systems Group, Inc. El Monte, CA 91732 USA Info@eesgi.com; INSTALLATION INSTRUCTIONS 1-877-579-3889 Mon.-Fri.
PAGE 2
Step 5 Testing your Dimmer prior to mounting in wall box: Wiring Diagram 1 : Single-Pole Control OPERATION Dimmer NOTE: After the code is successfully matched, the button is used as follows. • Restore power to the circuit breaker or fuse. • As shown in the figure, 1.Check the line connection turning on the switch button ensures the light turned on, then press the off button to turn off the light. 2.