GetEskimo.com ASSEMBLY INSTRUCTIONS & PARTS Eskape 200 Ice Shelter Model 69161 GetEskimo.com OM69161 Rev. 7/7/08 © 2008 Ardisam, Inc. All Rights Reserved.
HIGH PERFORMANCE ICE FISHING GEAR ® Eskape™ 200 Hardwater Series (69161) Eskimo Ice Shelters are engineered with you the high performance ice angler in mind. We appreciate your purchase of one of our high performance portable ice shelters. Follow these simple instructions and your ice shelter will provide you many years of trouble-free pleasure. Save these instructions for future reference.
HIGH PERFORMANCE ICE FISHING GEAR ® Eskape™ 200 Hardwater Series (69161) important safety precautions This tent is made with flame resistant fabric which meets CPAI-84 specifications. It is not fire proof. The fabric will burn if left in continuous contact with any flame source. warning The application of any foreign substance to the tent fabric may render the flame resistant properties ineffective. READ, UNDERSTAND and follow ALL ASSEMBLY, SAFETY, SET-UP & USE INSTRUCTIONS PROVIDED BEFORE EACH USE.
HIGH PERFORMANCE ICE FISHING GEAR ® Eskape™ 200 Hardwater Series (69161) ASSEMBLY Instructions Tools Needed - two 7/16” wrenches, one 3/8” wrench, one Phillips screwdriver and a rubber mallet. left hinge ASSEMBLY NOTE: This ice shelter should be assembled in a garage or basement setting due to the time and length of assembly. Identify and familiarize yourself with all parts and hardware before assembly. Allow 1-3 hours for assembly.
HIGH PERFORMANCE ICE FISHING GEAR ® Eskape™ 200 Hardwater Series (69161) 6. Slide the pre-assembled rod holder assembly (68449) into the T-slot of either bench seat rail. Doing so makes this bench seat rail the front rail and will be positioned beneath your legs during use. plastic storage tray (8) 10-24 nuts 7. Attach (2) bench seat rails (68301) to the top side of seat kit mount brackets using (4) provided 1/4-20 x 2-1/2” bolts, nyloc nuts and (4) washers. SEE FIGURE 3A.
HIGH PERFORMANCE ICE FISHING GEAR ® Eskape™ 200 Hardwater Series (69161) 10. Attach the (2) outer backrest brackets (68322) and the plastic storage tray to the bench seat rails using (4) provided 1/4-20 x 3-1/2” Phillips head bolts, nyloc nuts and washers. SEE FIGURE 4. 11. Attach the (2) 19” padded seat assemblies (68153) and the (1) 12” padded seat assembly (68004) to the curled lip of front bench seat rail by hooking the curled end of seat bracket into the curled end of bench seat rail.
HIGH PERFORMANCE ICE FISHING GEAR ® Eskape™ 200 Hardwater Series (69161) 15. Insert rear hinge upright pole from each hinge into the (1) rear top cross brace pole (68352 which measures approximately 59.45” x 25.14”). Making sure the lever side of large, red QRS pole clip is inline with the push button of hinge poles, push the snap buttons inward to allow cross brace pole to go over hinge poles and slide them to their shortest height (transport mode). SEE FIGURE 5. 16.
HIGH PERFORMANCE ICE FISHING GEAR ® Eskape™ 200 Hardwater Series (69161) 19. Assemble the two sets of door spreader poles (68046 & 68148) by sliding male half into the female half and snapping in place with snap button. SEE FIGURE 7. snap button snapped in place 20. Unzip door and move to the inside of shelter and extend the (3) top cross brace poles and snap into place.
HIGH PERFORMANCE ICE FISHING GEAR ® Eskape™ 200 Hardwater Series (69161) SET-UP & USE INSTRUCTIONS Set-up: From the outside or inside of shelter, depending on your preference, start with the bottom cross brace pole and pull out all cross brace poles and snap into place. As you pull out each cross brace pole and snap into place, flip all cross braces over to the in use position. Secure all spreader poles in between all cross brace poles by snapping C-clips over cross brace poles.
HIGH PERFORMANCE ICE FISHING GEAR ® Eskape™ 200 Hardwater Series (69161) STANDARD ACCESSORIES Removable Gear Table This gear table is designed to lock into the curled lip of the rear aluminum bench seat rail. It works just like the flip up seats, as you can flip the table up and access gear underneath.
HIGH PERFORMANCE ICE FISHING GEAR ® Eskape™ 200 Hardwater Series (69161) ESKAPE 200 PARTS 6 12 RIGHT SIDE 12 10 9 7 17 18 5 27 13 1 3 19 15 16 5 14 2 8 4 LEFT SIDE 11 15 24 24 25 26 21 22 21 20 20 20 23 Eskape 200 hinge assembly (right side shown) 1-800-345-6007 Eskape 200 assembled Page 11 GetEskimo.
HIGH PERFORMANCE ICE FISHING GEAR ® Eskape™ 200 Hardwater Series (69161) PARTS LISTS REF. NO. PART NO. QTY. 1 BOLT, 1/4-20 X 3/4” hh gr5 DESCRIPTION 8930 4 2 washer, 1/4” 48261 6 3 NUT, 1/4-20 HEX NYLOCK 67538 10 4 BOLT, 1/4-20 X 7/8” HHCS GR5 67541 6 5 POLE ASSEMBLY, SPREADER female (includes one .875” large clip) 68046 2 6 POLE ASSEMBLY, SPREADER 36” (includes two .706” large clips) 68033 1 7 POLE ASSEMBLY, SPREADER 40.10” (includes one .706” large clip & one .
HIGH PERFORMANCE ICE FISHING GEAR ® Eskape™ 200 Hardwater Series (69161) ESKAPE 200 SEAT PARTS 12 REF. NO. 18 9 12 DESCRIPTION PART NO. QTY.
HIGH PERFORMANCE ICE FISHING GEAR ® Eskape™ 200 Hardwater Series (69161) FAQ’S: (Frequently Asked Questions) • How can I keep mice and other rodents from damaging my ice shelter? During the off season, you should always remove your ice shelter skin, padded seats and padded backrests from the sled and poles and make sure it is dry. Fold skin up, store items in a large plastic container with lid and store in a cool, dry place. The use of moth balls or dryer sheets may be helpful also.
HIGH PERFORMANCE ICE FISHING GEAR ® Eskape™ 200 Hardwater Series (69161) WARRANTY ONE YEAR Limited Warranty Ardisam, Inc., a manufacturing company, warrants this Eskimo Ice Shelter to be free from defects in the material or workmanship for a period of one year from the date of purchase. During the one year warranty of this product, Ardisam will furnish 100% parts and labor to correct any defect caused by faulty material or workmanship.
ACCESSORY CHART ITEM # DESCRIPTION MSRP* 69195 High Speed Tracking Kit, Eskape 200 $59.99 69171 Travel Cover, Eskape 200 $55.99 69106 Tow Hitch, Eskape 200 $49.99 * Prices shown do not include shipping & handling charges. All prices are subject to change without notice. When ordering from manufacturer, there is a $10.00 minimum order. For replacement parts, phone 1-800-345-6007 or go online to www.GetEskimo.com Visit www.ardisam.
