User Manual
Table Of Contents
- Manufacturer: Esprit Model
- DC-DS-16-EN-Part 1.pdf
- DC-DS-16-EN-Part 2.pdf
- Stránka 18
- Stránka 19
- Stránka 20
- Stránka 21
- Stránka 22
- Stránka 23
- Stránka 24
- Stránka 25
- Stránka 26
- Stránka 27
- Stránka 28
- Stránka 29
- Stránka 30
- Stránka 31
- Stránka 32
- Stránka 33
- Stránka 34
- Stránka 35
- Stránka 36
- Stránka 37
- Stránka 38
- Stránka 39
- Stránka 40
- Stránka 41
- Stránka 42
- Stránka 43
- Stránka 44
- Stránka 45
- Stránka 46
- Stránka 47
- Stránka 48
- Stránka 49
- Stránka 50
- Stránka 51
- Stránka 52
- Stránka 53
- Stránka 54
- Stránka 55
- Stránka 56
- Stránka 57
computer
radio
control
system
EN
4.
4.
2. Enable an Alarm
Us
ing the „3D
button“
,
select „Enabled“ and press to enable
the
alarm and display the alarm
paramet
ers
.
3. Parameter
V
alues
„Condition“ defines the condition which must be met in order
t
o
trigger the alarm.
T
he
value
„
X“
will
var
y
with the sensor being
used
.
4. File
This
item allows you to select the audio
file
that is played when
the
alarm
oc
curs
.
Press
„F1“
to play the selected audio
file.
Press
„F2“
t
o
stop playing the selected audio
file
.
5.
Repea
t
If
the alarm condition occurrence is longer than the selected
audio
file,
you can use this item to repeat the audio
file. If
a check mark is
displayed then the audio
file will
repeat.
If
an
„x“
is displayed
then
the audio
file
will
play
only
onc
e
.
6. Set
T
hr
ottle
Idle
With
this item
activat
ed
,
you
model
’
s
throttle
will
go to idle when
the
alarm condition
oc
currs
.
7. Activation
S
witch
If
the switch is
assig
ned
,
the alarm is enabled or disabled
ac
c
or
ding
to the switch
status
.
9.4.3 Vario
L
ocat
ed
in:
„Men
u->T
imers/S
ensors/Vario
”
.
T
her
e
are two types of
acoustic
sig
nalling
.
T
he
first
one
is
controlled directly by the
sensor's
alarm.
This is
mainly useful
if
a
non-EX
MVARIO is
installed inside
the
model
.
I
t
is possible to assign a switch that enables or disables
the
sound
.
T
he
slider at the
bottom
shows the actual value of
climb/sink
rat
e
.
T
he
second mode of the
V
ario
is
dedicated
to
EX
sensors
.
T
he
acoustic signalling varies directly
depe
n
d
i
ng
on the
a
c
t
u
a
l
numerical values sent by the
sensor
.
I
t
is also possible to assign
a
switch that enables the acoustic
sig
nal
.