Turn your GoPro® LCD Touch BacPac into a Wi-Fi Live Viewer USER MANUAL
Table of Contents 1. Understanding This User Manual 3 2. Product Components and Features 4 3. U sing REMOVU P1 5 Charging the Battery 5 How to Assemble 5 Turning Your Device On and OFF 6 Wi-Fi Connection: Connecting Your GoPro for the first time (HERO3, 3+) 7 Wi-Fi Connection: Connecting Your GoPro for the first time (HERO4) 8 Wi-Fi Connection: Connection Failure / Reconnect 9 LCD Screen Indicators 10 Navigating Your Device 11 Controlling GoPro (Power On / Off) 12 4-1.
1. Understanding This User Manual Thank you for purchasing our Wireless GoPro Live Viewing Device, REMOVU P1 (hereinafter referred to as “P1”). This Operator’s Guide describes how to handle and operate the P1. Before using the P1, be sure to read this manual thoroughly for proper operation. To enhance the performance of the product, the contents of this instruction manual may be changed without prior notice.
2. Product Components and Features Package Component Please make sure your package includes all of the following items. SET WRISTBAND USB CABLE QUICK GUIDE Names of Each Part 1 6 2 7 3 5 4 1. Shutter / Select 5. Charging Status LED 2. Power / Mode / Next 6. Reset 3. ESC / Previous 7. USB Connector 4.
3. Using the REMOVU P1 Charging the Battery *The battery should be fully charged before using P1 the first time. 1. Connect the device to a computer USB port using the micro USB cable included in the package. 2. P1 can also be charged with a USB power adapter. (Adaptor’s not included) We recommend using GoPro, or Apple iphone adaptors. How to Assemble P1 Cover GoPro® LCD Touch BacPac P1 Body 1. Open the cover and detach it from the body. 2. Place the LCD Bacpac into the slot as below. 3.
Turning Your Device On and OFF Turning it on 1. Press the M (Mode / Power) button for about 1 second to turn on the power. 2. The REMOVU logo will appear. After short loading, Wi-Fi network list will pop up. Turning it off 1. Press the M (Mode / Power) button for about 2 seconds to turn off the device. REMOVU Power off logo will appear then the device will be turned off with the red LED blinking three times. 2.
Wi-Fi Connections: Connecting Your GoPro for the first time. (HERO3, 3+ Users) HERO3, 3+ Wi-Fi SSID, and Password setup www.gopro.com /support 1. Go to GoPro support page on GoPro Website to upgrade your GoPro Camera to the latest firmware version. 2. While upgrading, you will be asked to set up Wi-Fi SSID, Password. Please make sure to remember your password and SSID. Connecting your GoPro HERO3, 3+ to REMOVU 1. Please go to the GoPro App settings menu on your HERO3, 3+ to turn on the Wi-Fi function.
Wi-Fi Connections: Connecting Your GoPro for the first time. (HERO4 Users) HERO4 Wi-Fi SSID, and Password setup 1. Install the GoPro App on your Smartphone. 2. Go to your GoPro 4 Setup ► Wireless ► select GoPro App. 6 digit Pin number will appear. 3. Open the GoPro App and connect your GoPro Camera. 4. Enter the 6 digit Pin number that the GoPro Camera is showing. 5. Create the SSID, and Password for your Camera. 6. After the connection is established, shut down the App.
Wi-Fi Connection: Connection Failure / Reconnect 1. Flashing red LED and Wi-Fi Network Not Connected message will appear if Wi-Fi fails to connect or lose its signal. 2. Type in your password again and try reconnecting the device. 3. If the connection is restored, blue LED will flash and the Live View will appear. 4. When reusing the device, P1 will try to connect to last device it was connected to using the information saved from previous use. 5.
LCD Screen Indicators 1 2 3 4 5 8 6 7 1. Camera Modes / FOV Indicator 5. GoPro Battery Life 2. Saved Image / Video Counter 6. Resolution / FPS 3. Remaining Recordable Hours / Number of Photos Counter 7. P1 Battery Life 8. Shooting Mode Indicator 4. Wi-Fi Signal Strength Indicator To Adjust Settings The settings can be adjusted in the Setting Mode.
Navigating Your Device After the device is powered on and Wi-Fi connection is established, it goes into the Live View mode automatically. From there, you can simply navigate through different functions using the Back button or the touch screen. The order of appearance of the functions are illustrated below.
Controlling GoPro (Power On / Off) Press and hold the M button for about 2 seconds until Power control menu appears. You will be given 3 options to chose from. - REMOVU Power Button: Turns On/Off REMOVU - GoPro Power Button: Turns On/Off GoPro - Power Button for both: Turns of both devices The RED triangle at the top-right corner of the buttons indicate that the device is turned on.
4-1.
VIDEO To record video, please swipe from right to left or tap the arrow on the right side of the screen or using the M button on the side of the device to change modes. Video icon appears at the top left corner of the Live View OSD. To start recording: Press the REC (Shutter / Select) button. The red LED Lights will flash while recording. To stop recording: Press the REC (Shutter / Select) Button while recording. The red LED light will flash three times and stops recording.
TIME LAPSE Time Lapse mode automatically captures a series of photos at 0.5, 1, 2, 5, 10, 30 or 60 second intervals. To capture a Time Lapse series, select the photo mode on the touch screen, or please press the M button repeatedly until the Time Lapse icon appears at the top left corner of the Live View OSD. To take time lapse photos: Press the REC (Shutter / Select) Button. The camera initiates countdown and the red Camera Status Lights flash each time a Photo is taken.
VIDEO RESOLUTION / FPS / FOV MODES The Resolution, fps (frames per second) and FOV (field of view) can be changed in the Video mode menu. You can also turn Auto Low Light mode ON / OFF. To change Video Mode settings: 1. Press the REC (Shutter / Select) Button to enter (VIDEO RESOLUTION / FPS / FOV MODES). 2. Use the M (Mode / Power) to navigate through options or by touch. 3. Press the REC (Shutter / Select) button to enter desired menu. 4.
CONTINUOUS PHOTO Continuous Photo mode allows you to capture a series of 3 Photos by pressing the REC (Shutter / Select) button. Speed Options: SINGLE Takes 3 photos in 1 second Takes 3 photos at speed of 5 photos/sec Takes 3 photos at speed of 10 photos/sec Tips: Y our camera will remain in Continuous Photo mode until you change it back to single Photo capture mode. BURST PHOTO OPTIONS Burst Photo mode captures a series of Photos when the REC (Shutter / Select) Button is pressed.
4-2. Modes and Settings - HERO4 Series Menu Tree Menu Rotation Sequence Please select the mode using the touch screen menu or M (Mode / Power) button to navigate across different modes.
Sub Menu Tree Please select the mode using the touch screen menu or long-press REC (Shutter / Select) button while in the desired Camara Mode to change the capture mode in the order listed of above. VIDEO MODE Video Captures video. Video + Photo Simultaneously captures both video and photos. You can set the camera to capture a photo at selected intervals while you record video. For details, see Video + Photo Intervals in this section.
MULTI-SHOT MODE Burst Captures up to 30 photos in 1 second. Perfect for capturing the definitive moment in fast-action sports. Time Lapse Captures a series of photos at specified intervals. You can use Time Lapse to capture photos of any activity, so you can choose the best ones later. Night Lapse Captures a series of photos at specific intervals and exposure times. Use Night Lapse in low light environments, such as when capturing the night sky over a period of time.
5. Firmware Upgrade 1. Please visit www.removu.com/firmware page to download the latest firmware. 2. Download the firmware file and unzip the file on your PC or Mac. 3. Turn on the REMOVU P1. 4. When “Select Camera Network” list appears on the REMOVU screen, connect the device to your PC or Mac using the USB cable included in the package. 5. Copy and paste the firmware files to the root of REMOVU storage drive. 6.
6. Product Specification Display Not built-in (using GoPro LCD Touch BacPac, GoPro LCD Touch BacPac is not included.) Video Streaming HLS | 432×240 @ 30fps Wi-Fi IEEE 802.11b/g/n Distance: 20m ~ 60m (Max) Antenna Well designed built-in PCB antenna Power and Battery 2.5 hours of continuous video streaming Built-in Rechargeable Li-polymer Battery 1,050mA Interface Micro USB (Charging & F/W update) Weight and Dimensions Height: 2.0 inches (52 mm) Width: 2.8 inches (72 mm) Depth: 1.
7. Trouble Shooting Guide 1. If “No firmware to update” message appears after firmware update, Solution: Connect your device to a PC and delete all files stored in the storage. Then copy the .bin firmware file to the memory and reboot. 2. If “Low firmware versions” message appears after firmware update, Solution: Connect your device to a PC and delete all files in the storage. Reboot to check the version of the firmware. 3.
8. Warranty Information Standard Limited Warranty Essel-t Co., LTD. (“essel-t”) warrants that essel-t’s devices and accessories (“Products”) are free from defects in material and workmanship under normal use and service for the period commencing upon the date of purchase by the first consumer purchaser and continuing for 1 year period of time after that date. Exclusions and Limitations This Limited Warranty is conditioned upon proper use of Product by Purchaser.
Obtaining Warranty Service For more information, please visit our website at www.removu.com and find out everything regarding our product. For additional assistance or questions regarding the product, please contact our C/S center, or the place of purchase. We will try our best to provide you with the highest possible standard of service. : This device complies with part 15 of the FCC Rules.
