Owners manual

ManualsBrandsEssential Home ManualsDining & Kitchen Furniture2 pc. Kendall Dining Chair Set

OWNER’S MANUAL

KENDALL DINING CHAIRS

Caution: Read owner's manual completely before assembly and use.

Product code: 0-08612933-5

UPC code: 729437125109

Date of purchase: / /

Summary of content (8 pages)

PAGE 1
OWNER’S MANUAL KENDALL DINING CHAIRS Caution: Read owner's manual completely before assembly and use.
PAGE 2
M A X I M U M R E CO M M E N D E D W E I G H T C A PAC I T Y 1. Chair-maximum load weight per chair is 300 pounds. G E N E R A L I N F O R M AT I O N & T I P S 1. Please read the assembly instructions prior to assembling this product. 2. To avoid damage, assemble this product on a non-abrasive surface such as carpet. 3. Make sure all bolts, nuts, and screws are tightly fastened before the product is used. 4. Not for commercial use. 5. Care: Wipe with a damp cloth.
PAGE 3
PA RT S L I ST A. Chair Back B. Seat Frame C. Chair Seat QTY: 2 pcs QTY: 2 pcs QTY: 2 pcs D.
PAGE 4
HA R D WA R E L I ST 1. Flat Washer 2. Spring Washer 3. Wood Screw QTY: 20 pcs QTY: 20 pcs QTY: 8 pcs 4. Long Bolt 5. Medium Bolt 6. Short Bolt Dia 1/4 x 3 inch L QTY: 8 pcs Dia 1/4 x 2-1/2 inch L QTY: 8 pc Dia 1/4 x 1-1/2 inch L QTY: 4 pc 7.
PAGE 5
A S S E M B LY I N S T R U C T I O N S Diagram #1 a 7 A 6 2 1 B B b A 7 4 2 1 A B Step 1 1. Attach Seat Frame (B) to Chair Back (A) using Short Bolt (6), Spring Washer (2) and Flat Washer (1) as shown in inset (a); using Long Bolt (4), Spring Washer (2) and Flat Washer (1) as shown in inset (b). Do not tighten the bolts at this step.
PAGE 6
A S S E M B LY I N S T R U C T I O N S Diagram #2 a B B D 1 D 2 5 A Step 2 2. Attach Front Legs (D) to the assembled unit from Step 1, using Medium bolt (5), Spring Washer (2) and Flat Washer (1) as shown in inset (a). Do not tighten the bolts at this step. 3. Turn the chair upright. Make sure the assembled chair is level and square. Tightly fasten all bolts with the Allen Wrench (7).
PAGE 7
A S S E M B LY I N S T R U C T I O N S Diagram #3 a 3 C C Step 3 4. Place Chair Seat (C) upside down on a non-abrasive table surface. The rear (tapered end) on the Seat Frame (B) should be near the table edge. Hint: Protect the non-abrasive table surface and Chair Seat (C) by laying a towel in-between the chair seat and table. 5. Place the assembled Chair Frame on the Chair Seat (C) as shown. Attach with Wood Screw (3) as shown in inset (a) with Phillips head screwdriver (not provided). 6.
PAGE 8
Please refer to part numbers when reordering For questions or comments about product: Email: css@yingfu.biz Made in / Hecho en VIETNAM. Distributed by Kmart Corporation, Hoffman Estates, IL 60179 SHOP kmart.