M_FC01_LQ_0408_e M_FC01_LQ_0408_e Circuit Protection & Control Circuit Protection & Control Flow Meter FC01-LQ User handbook Flow Meter FC01-LQ User handbook
Flow Meter FC01-LQ Please follow these installation and adjustment instructions carefully. Failure to comply with these instructions or misuse of this equipment will void your warranty coverage. Flow Meter FC01-LQ Please follow these installation and adjustment instructions carefully. Failure to comply with these instructions or misuse of this equipment will void your warranty coverage. The instructions cover software version 1.00. The instructions cover software version 1.00.
Flow Meter FC01-LQ Flow Meter FC01-LQ Table of content Table of content 1 1 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1.1 1.2 Calorimetric monitoring procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 1.1 System description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1.2 1.2.1 2 User interfaces . . . . . .
Flow Meter FC01-LQ 4 Operation and main menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 4.1 Switch-on performance Measuring cycle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 4.2 Measuring cycle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Operating data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Flow Meter FC01-LQ 8 Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 8 Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 8.1 Ambient conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 8.1 Ambient conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Flow Meter FC01-LQ Flow Meter FC01-LQ
Flow Meter FC01-LQ Flow Meter FC01-LQ 1 Description 1 Description The Flow Meter FC01-LQ is designed to detect flow speed, flow volume and medium temperature of water (other liquids upon request). The Flow Meter FC01-LQ is designed to detect flow speed, flow volume and medium temperature of water (other liquids upon request).
Flow Meter FC01-LQ Flow Meter FC01-LQ 1.1 Calorimetric monitoring procedure 1.1 Calorimetric monitoring procedure The calorimetric measuring procedure is based on the physics of heat dissipation. The calorimetric measuring procedure is based on the physics of heat dissipation. A body with a temperature higher than its surroundings supplies a medium flowing past that body with energy in the form of heat. The amount energy supplied is a function of temperature difference Δϑ and mass flow.
Flow Meter FC01-LQ Flow Meter FC01-LQ 1.2 System description 1.2 System description The system comprises the following hardware functional modules: The system comprises the following hardware functional modules: 1 Input voltage 1 Input voltage DC supply (terminal XV) 2 User interfaces: 2.1 signal outputs 2-way or 4-way signal outputs (terminal XAH) DC supply (terminal XV) 2 User interfaces: 2.1 signal outputs 3 Keyboard and display: 2-way or 4-way signal outputs (terminal XAH) 2.
Flow Meter FC01-LQ Flow Meter FC01-LQ The power supply is physically isolated between power supply input and system power supply output. This also applies to the analogue and signal outputs which are physically isolated from each other as well as from the other electronics. The power supply is physically isolated between power supply input and system power supply output.
Flow Meter FC01-LQ Power supply: Description Flow Meter FC01-LQ DC 24 V supply Power supply: DC 24 V supply Internal switch mode power supply with physical isolation of the primary and secondary side. Internal switch mode power supply with physical isolation of the primary and secondary side. Noise emission on the connection cable is limited by circuit design and filter. Noise emission on the connection cable is limited by circuit design and filter.
Flow Meter FC01-LQ Flow Meter FC01-LQ 2 Installation 2 Installation These are general directions for the application of calorimetric measuring heads which from application to application should be reviewed by the user in accordance with individual requirements. These are general directions for the application of calorimetric measuring heads which from application to application should be reviewed by the user in accordance with individual requirements. 2.1 Selection of material 2.
Flow Meter FC01-LQ Flow Meter FC01-LQ 2.2 Installation of the monitoring heads 2.2 Installation of the monitoring heads 2.2.1 Insertion head CSP for sensor adapter TP-.. and ball valve BV-.. 2.2.1 Insertion head CSP for sensor adapter TP-.. and ball valve BV-.. Application: general industry and installation Style: insertion-type for sensor adapter and ball valve Installation: sensor adapter TP-.. (fig. 4) ball valve BV-.. (fig.
Flow Meter FC01-LQ Flow Meter FC01-LQ 2.2.1.1 Sensor adapter TP-.. 2.2.1.1 Sensoradapter TP-.. The sensor adapter TP-.. is available in 6 pipe diameters from 1/2" to 2". Sensor adapter is available as screw-in (fig. 4 top) or welding type (fig. 4 bottom). The sensor adapter TP-.. is available in 6 pipe diameters from 1/2" to 2". Sensor adapter is available as screw-in (fig. 4 top) or welding type (fig. 4 bottom).
Flow Meter FC01-LQ Flow Meter FC01-LQ 2.2.1.3 Ball valve BV-… Ball valve BV-… The ball valve of Postberg GmbH at D-63485 Bruchköbel is available in 4 nominal diameters from 1" to 2". The ball valve ensures the sensors are fully immersed in the medium. The ball valve of Postberg GmbH at D-63485 Bruchköbel is available in 4 nominal diameters from 1" to 2". The ball valve ensures the sensors are fully immersed in the medium. The monitoring head may also be replaced in pressurised pipe systems on duty.
Flow Meter FC01-LQ Flow Meter FC01-LQ 2.2.2 Monitoring head CSF-11 with adjustable immersion depth 2.2.2 Monitoring head CSF-11 with adjustable immersion depth Application: pipelines with nominal pipe diameters > DN50 Application: pipelines with nominal pipe diameters > DN50 Medium: liquids Medium: liquids Style: smooth shank, 18 mm dia., immersion depth adjustable within the PG16 cable gland (accessory) or mounting in the stainless steel cutting ring gland Style: smooth shank, 18 mm dia.
Flow Meter FC01-LQ Flow Meter FC01-LQ 2.2.2.1 Mounting instructions for monitoring head CSF-11 2.2.2.1 Mounting instructions for monitoring head CSF-11 Caution! Caution! The two sensors (M) should be screwed into the pipeline far enough to ensure that they are aligned side by side directly across the direction of flow. The sensors are correctly positioned when the wrench flats (S) are aligned parallel with the pipeline.
Flow Meter FC01-LQ ● Flow Meter FC01-LQ The monitoring head should be installed only in a straight section of piping. There should be a distance of at least 20 pipe diameters before the monitoring head, and 5 pipe diameters after the monitoring head before or after bends and changes in pipe diameter, to avoid any effects of turbulence. The monitoring head should be installed only in a straight section of piping.
Flow Meter FC01-LQ Flow Meter FC01-LQ Locking set 01 Locking set 01 1 1 2 3 2 chain 4 x 32 DIN 5685 (approx. 1 m) catch for chain NG 5 clip with screws and nuts DN15 to DIN 11850 (tightening torque 10 Nm) 1 3 fig. 9 2.2.
Flow Meter FC01-LQ Flow Meter FC01-LQ 2.3 Installation of electronic control unit FC01-LQ 2.3 Installation of electronic control unit FC01-LQ 2.3.1 Mechanical installation 2.3.1 Mechanical installation 2.3.1.1 Rail-mounted version FC01-LQ-U1... 2.3.1.1 Rail-mounted version FC01-LQ-U1... ● The electronic housing is mounted on a symmetric rail to EN 50022. ● The electronic housing is mounted on a symmetric rail to EN 50022. ● For thermal reasons, the modules should be spaced by at least 10 mm.
Flow Meter FC01-LQ Flow Meter FC01-LQ 2.3.1.2 Surface mounted version FC01-LQ-FH-U1... 2.3.1.2 Surface mounted version FC01-LQ-FH-U1... ● Remove the cover of the housing. ● Remove the cover of the housing. ● Install the housing in place using the 4 self-taping screws M4 (see fig. 12). ● Install the housing in place using the 4 self-taping screws M4 (see fig. 12). ● Replace the cover and tighten the retaining screws. ● Replace the cover and tighten the retaining screws.
Flow Meter FC01-LQ Flow Meter FC01-LQ 2.3.1.3 Front panel mounted housing FC01-LQ-ST-U1... Insert housing in the front of mounting hole and fix with 4 screws (see fig. 13) from the rear. mounting hole DIN 43700 144 mounting hole DIN 43700 M 96 M 96 Insert housing in the front of mounting hole and fix with 4 screws (see fig. 13) from the rear. 140 92 144 ● 92 ● 2.3.1.3 Front panel mounted housing FC01-LQ-ST-U1... 4 4 82 82 140 fig. 13 16 Installation fig.
Flow Meter FC01-LQ Flow Meter FC01-LQ 2.3.2 Electrical connection 2.3.2 Electrical connection Valid for all plug-in screw terminal strips: Valid for all plug-in screw terminal strips: Cable size: 0.14 mm2 to 1.5 mm2, single or stranded conductor Cable size: 0.14 mm2 to 1.5 mm2, single or stranded conductor Stripping length: 6.5 mm Stripping length: 6.
Flow Meter FC01-LQ Flow Meter FC01-LQ XAO - Analogue outputs XAO - - Analogue outputs 2 2 Connection by 8 pole connector; max. 1.5 mm ; LiYCY 2 x 0.25 mm cable recommended for each analogue output Connection by 8 pole connector; max. 1.5 mm 2; LiYCY 2 x 0.25 mm2 cable recommended for each analogue output Pin selection for analogue outputs (option: V1, V2, C1) Pin selection for analogue outputs (option: V1, V2, C1) Pin No.
Flow Meter FC01-LQ Flow Meter FC01-LQ 5 LIM2 E limit value 2 - emitter terminal 5 LIM2 E limit value 2 - emitter terminal 6 LIM2 C limit value 2 - collector terminal 6 LIM2 C limit value 2 - collector terminal 7 LIM1 E limit value 1 - emitter terminal 7 LIM1 E limit value 1 - emitter terminal 8 LIM1 C limit value 1 - collector terminal 8 LIM1 C limit value 1 - collector terminal XSK - Connection of calorimetric monitoring head type CS_ x XSK - Connection of calorimetric monitoring
* ** analogue outputs ** C1, V1, V2 8 1 * ** } signal outputs 20 4 5 6 7 8 1 2 3 4 5 6 7 8 analogue outputs ** C1, V1, V2 1 signal outputs } Installation 3 } fig. 15 recommended SGNDA1 ungrounded SGNDA2 Apply shield one side only. } 2 2 3 1 M XAO 4 2 5 6 /LIM2 7 3 LIM2COM 6 XSK 2 LIM2 5 1 LiYCY 3x0.38 mm2 * 4 9 10 /LIM1 3 (XAS) 8 SGNDL2 XV 7 LIM1COM FC01-LQ 6 LiYCY 3x0.38 mm2 * 2 5 LIM1 1 4 SGNDL1 XAH 3 ANA2GND Flow Controller 2 ANAO2 XTF 1 LiYCY 2x0.
* ** E/ - emitter terminal C/+ collector terminal * ** signal outputs fig. 16 21 Installation recommended SGNDA1 ungrounded SGNDA2 Apply shield one side only. } E/ - emitter terminal C/+ collector terminal 1 2 3 4 5 6 7 8 analogue outputs ** C1, V1, V2 1 2 3 4 C/ + XAO E/ - 8 3 C/ + 7 2 LIM1 6 1 LIM1 5 9 10 E/ - (XAS) 8 LIM2 FC01-LQ 7 LIM2 4 6 C/+ 3 XSK /BUSY/PULSE C/ + 2 5 /BUSY/PULSE E/ - 1 4 /ERROR 8 3 LifYCY 4x2x0.
Flow Meter FC01-LQ Flow Meter FC01-LQ 2.3.2.3 Electrical connection - frequency output (version FC01-LQ-U1T4) 2.3.2.3 Electrical connection - frequency output (version FC01-LQ-U1T4) The quantity-dependent pulse may be selected in the menu item “DISPLAY SELECT”. A square pulse signal is available for driving a counter or a primary control at the plug XAH /BUSY E/- and /BUSY C/+ (pins 3 and 4) (see fig. 16 - circuit diagram FC01-LQ - transistor outputs).
Flow Meter FC01-LQ Flow Meter FC01-LQ Electromechanical pulse counter (fig. 18) Electromechanical pulse counter (fig. 18) The FC01-LQ driver output comprises an integral safety circuit which when isolating the counter operating coil will limit overvoltages caused by inductance and convert the energy stored. The FC01-LQ driver output comprises an integral safety circuit which when isolating the counter operating coil will limit overvoltages caused by inductance and convert the energy stored.
Flow Meter FC01-LQ Flow Meter FC01-LQ 3 Operating system 3 Operating system Clear menu-driven control, via keyboard and display, enables easy definition of parameters and configuration. This provides high system flexibility, making the FC01-LQ the optimum solution for a wide variety of measuring, monitoring and display tasks. Clear menu-driven control, via keyboard and display, enables easy definition of parameters and configuration.
Flow Meter FC01-LQ Flow Meter FC01-LQ Menu paging Menu paging The next menu option is selected by pressing M MODE (forward paging). The next menu option is selected by pressing M MODE (forward paging). Pressing M MODE after the last menu option will cause skipping to the first option of the menu. Pressing M MODE after the last menu option will cause skipping to the first option of the menu.
Flow Meter FC01-LQ Flow Meter FC01-LQ 4 Operation and main menu 4 Operation and main menu 4.1 Switch-on performance 4.1 Switch-on performance Upon power application POWER ON TEST will be shown on the display for approx. 1 sec., with the software version number being indicated in the second line. Upon power application POWER ON TEST will be shown on the display for approx. 1 sec., with the software version number being indicated in the second line.
Flow Meter FC01-LQ Flow Meter FC01-LQ 4.2.1 Operating data 4.2.1 Operating data 4.2.1.1 Measured value(s) 4.2.1.1 Measured value(s) Flow rate and medium temperature are indicated by the units selected in the upper line of the LC display. Flow rate and medium temperature are indicated by the units selected in the upper line of the LC display.
Flow Meter FC01-LQ Flow Meter FC01-LQ The limit switches are identified according to their physical assignment, i.e. by F for flow rate and T for medium temperature, at the first or last place of the second line on the display. The limit switches are identified according to their physical assignment, i.e. by F for flow rate and T for medium temperature, at the first or last place of the second line on the display. If F and T are shown reversed, the limit switch is in the switch-on condition.
Flow Meter FC01-LQ Flow Meter FC01-LQ 4.2.1.4 Main menu 4.2.1.4 Main menu power-on power-on HEATING UP * F F 12.5 m/s F HEATING UP * T F T F -13.5 °C * F F 12.5 m/s 10.8 m/s -19.5 °C * ▲+▼ 10.8 m/s delete minimum values ▲+▼ 14.8 m/s delete maximum values -13.5 °C * -105.6 °C * ▲+▼ 12.5 m/s See section 5 menu Configuration CONFIGURATION -13.5 °C * -13.5 °C * ▲+▼ HEATING UP * PARAMETERS See section 6 menu Parameter Selection 12.5 m/s -13.
Flow Meter FC01-LQ Flow Meter FC01-LQ 5 Configuration (menu option: CONFIGURATION) 5 Configuration (menu option: CONFIGURATION) The CONFIGURATION menu serves to adjust the FC01-LQ to the application within the entire system. During system configuration, measuring operations are not possible (see appendix 1). Configuration possibilities are: The CONFIGURATION menu serves to adjust the FC01-LQ to the application within the entire system.
Flow Meter FC01-LQ Flow Meter FC01-LQ Enter the following characteristics when selecting a CSP monitoring head with sensor adapter TP-..: Enter the following characteristics when selecting a CSP monitoring head with sensor adapter TP-..: 1. SENSOR CODE C value characteristics range: 700 … 1300 1. SENSOR CODE C value characteristics range: 700 … 1300 2. SENSOR CODE T value characteristics range: 01 … 99 2.
Flow Meter FC01-LQ Flow Meter FC01-LQ 5.4 Flow rate unit (menu option: FLOW UNIT) 5.4 Flow rate unit (menu option: FLOW UNIT) At these point (1st line top left) the requested unit for the flow velocity will be set. At these point (1st line top left) the requested unit for the flow velocity will be set.
Flow Meter FC01-LQ Flow Meter FC01-LQ Caution! Caution! The content of the totalizer is deleted in the event of power failure or disconnection of the power supply! The content of the totalizer is deleted in the event of power failure or disconnection of the power supply! Skipping to the submenu BARGRAPH or PIPE SIZE is effected depending on the selected menu option. Skipping to the submenu BARGRAPH or PIPE SIZE is effected depending on the selected menu option. 5.
Flow Meter FC01-LQ Flow Meter FC01-LQ 5.8 Pipe diameter (menu option: PIPE SIZE) 5.8 Pipe diameter (menu option: PIPE SIZE) If flow volume/time unit display has been selected, it is necessary to indicate the pipe diameter to calculate mass flow. If flow volume/time unit display has been selected, it is necessary to indicate the pipe diameter to calculate mass flow. This is provided by selecting the pipe diameter in menu option PIPE SIZE comprising pipe diameters from 10.0 … 999.9 mm.
Flow Meter FC01-LQ Flow Meter FC01-LQ 5.10 Analogue output - flow rate (menu option: ANA OUT FLOW) 5.10 Analogue output - flow rate (menu option: ANA OUT FLOW) This menu option allows adjustment of the flow rate analogue output specifically to the requirement of the entire system. This menu option allows adjustment of the flow rate analogue output specifically to the requirement of the entire system.
Flow Meter FC01-LQ Flow Meter FC01-LQ • ERR. BARGRAPH OUT OF RANGE (bar value outside measuring range) • ERR. BARGRAPH OUT OF RANGE (bar value outside measuring range) • ERR. BARGRAPH ZERO ≥ FS (bar initial value ≥ bar final value) • ERR. BARGRAPH ZERO ≥ FS (bar initial value ≥ bar final value) The menu can only be quitted after correction of the error(s). To do this, return to the beginning The menu can only be quitted after correction of the error(s).
Flow Meter FC01-LQ Flow Meter FC01-LQ 5.13 Configuration menu 5.
38 submenu sensor select BV SIZE SELECT DN25 (1 in) Configuration 38 A submenu sensor select BV SIZE SELECT DN32 (1.1/4 in) ▲ or ▼ BV SIZE SELECT DN50 (2 in) ▲ or ▼ BV SIZE SELECT DN40 (1.1/2 in) ▲ or ▼ BV SIZE SELECT DN32 (1.1/4 in) ▲ or ▼ BV SIZE SELECT DN25 (1 in) M SENSOR CODE T xxx M SENSOR CODE C xxx M ▲ or ▼ ▲ or ▼ BV SIZE SELECT DN50 (2 in) ▲ or ▼ BV SIZE SELECT DN40 (1.
Configuration FLOW UNIT METRE/SEC (m/s) TEMP. UNIT CELSIUS (°C) submenu flow unit submenu temperature unit B C D 39 Configuration LIMIT SWITCHES LS1 → F LS2 → F FLOW UNIT METRE/SEC (m/s) TEMP. UNIT CELSIUS (°C) submenu limit switch combination submenu flow unit submenu temperature unit B C D ▲ or ▼ M Conf. TEMP. UNIT FAHRENHEIT (°F) FLOW UNIT PERCENT (%) ▲ or ▼ M Conf. ▲ or ▼ M M ▲ or ▼ Conf. Conf. ▲ or ▼ M ▲ or ▼ Conf. ▲ or ▼ M LIMIT SWITCHES LS1 → T LS2 → T TEMP.
40 Configuration Conf. M ANA OUT TEMP. FS = 85.0 °C M ANA OUT TEMP. ZERO = -10.0 °C M ANA OUT TEMP. OFFSET = (FS) submenu analogue temperature submenu analogue flow submenu display selection Conf. 40 G F E Conf. M ANA OUT TEMP. FS = 85.0 °C M ANA OUT TEMP. ZERO = -10.0 °C M ANA OUT TEMP. OFFSET = (FS) submenu analogue temperature submenu analogue flow submenu display selection M ANA OUT FLOW FS = 3.5 m/s M ANA OUT FLOW ZERO = 0.5 m/s M ANA OUT FLOW OFFSET = (FS) Conf.
Flow Meter FC01-LQ Flow Meter FC01-LQ 6 Parameter selection (menu option: PARAMETERS) 6 Parameter selection (menu option: PARAMETERS) After configuration of the FC01-LQ in conformance with its application (configuration menu), it is possible to set parameters (e.g. limit values). After configuration of the FC01-LQ in conformance with its application (configuration menu), it is possible to set parameters (e.g. limit values).
Flow Meter FC01-LQ Flow Meter FC01-LQ Example for ON: Example for ON: FC01-LQ with relay outputs (option R2): FC01-LQ with relay outputs (option R2): • LIM1 - LIM1COM = closed • LIM1 - LIM1COM = closed /LIM1 - LIM1COM = open /LIM1 - LIM1COM = open FC01-LQ with transistor outputs (option T4): FC01-LQ with transistor outputs (option T4): • LIM1E - LIM1C = switched • LIM1E - LIM1C = switched Example 2: Switch-on value higher than switch-off value switch-off value Example 2: Switch-on value high
Flow Meter FC01-LQ Flow Meter FC01-LQ 6.5 Quitting the parameter selection menu 6.5 Quitting the parameter selection menu Before the parameter selection menu can be quitted, the controller will conduct a plausibility check of the data entered. Before the parameter selection menu can be quitted, the controller will conduct a plausibility check of the data entered. “PARAMETERS OK!” is indicated when the data are found to be correct.
Flow Meter FC01-LQ Flow Meter FC01-LQ 6.6 Parameter selection menu 6.6 Parameter selection menu PARAMETERS PARAMETERS ▲+▼ ▲+▼ PARAMETERS MEAS. TIME = 3 sec PARAMETERS MEAS. TIME = 3 sec M M PARAMETERS LS1 ON = 1.24 m/s PARAMETERS LS1 ON = 1.24 m/s M M PARAMETERS LS1 OFF = 1.50 m/s PARAMETERS LS1 OFF = 1.50 m/s M M PARAMETERS LS2 ON = 73.0 °C PARAMETERS LS2 ON = 73.0 °C M M PARAMETERS LS2 OFF = 68.5 °C PARAMETERS LS2 OFF = 68.5 °C M M PARAMETERS FLOWSCALE 1.
Flow Meter FC01-LQ Flow Meter FC01-LQ 7 Errors 7 Errors 7.1 Test and diagnosis 7.1 Test and diagnosis The FC01-LQ is provided with extensive test and diagnosis functions which may be classified as follows: The FC01-LQ is provided with extensive test and diagnosis functions which may be classified as follows: 7.1.1 Priority group I 7.1.1 Priority group I Priority group I comprises the switch-on test routines (FC01-LQ self-test) which are carried out when the system is switched on.
Flow Meter FC01-LQ Flow Meter FC01-LQ 7.2 Potential errors 7.2 Potential errors Independent of the priority group, all errors found are indicated with their relevant number. Independent of the priority group, all errors found are indicated with their relevant number. In order to facilitate operation, the last error is stored in a non-volatile memory. The stored error may be retrieved and deleted in the main menu. In order to facilitate operation, the last error is stored in a non-volatile memory.
Flow Meter FC01-LQ Flow Meter FC01-LQ Priority group III Error Cause Priority group III Rectification Error Cause No. 20 Medium temperature too low No. 20 Medium temperature too low No. 30 Over limits of flow rate No. 30 Over limits of flow rate No. 60 Assignment of quantity per pulse too low * No. 60 Assignment of quantity per pulse too low * No. 40 Controller error (oscillator-watchdog) No. 40 Controller error (oscillator-watchdog) Admissible EMC levels may have been exceeded No.
Flow Meter FC01-LQ Flow Meter FC01-LQ 8 Technical data 8 Technical data 8.1 Ambient conditions 8.1 Ambient conditions rail-mounted surface mounted front panel mounted Storage temperature: -20 … +70 °C -20 … +70 °C -20 … +70 °C Ambient temperature: * +10 … +50 °C ** +10 … +50 °C +10 … +50 °C IP65 IP65 Degree of protection: IP20 * Only if the modules are spaced by at least 10 mm. ** The max. ambient temperature of +40 °C applies to all systems fitted with current output C1.
Flow Meter FC01-LQ Flow Meter FC01-LQ Inrush current: Ip = typ. 3 A (20 µs) Inrush current: Ip = typ. 3 A (20 µs) Switch-off current: Ikipp = typ. 0.75 A Switch-off current: Ikipp = typ. 0.75 A Pn = 4.1 W with zero flow, voltage outputs Rated power consumption: Rated power consumption: Insulation voltage: Pn = 4.1 W with zero flow, voltage outputs Pn = 4.8 W max. flow (end of measuring range), voltage outputs Pn = 4.8 W max.
Flow Meter FC01-LQ Flow Meter FC01-LQ 8.3.1 Voltage output V1 - 5 V FS 8.3.1 Voltage output V1 - 5 V FS Signal voltage range: US = 0 V (1 V) to 5 V ±2% FS Signal voltage range: Max. signal rippl: dUS = 5 % FS Max. signal rippl: dUS = 5 % FS Min. admissible load resistance: R l = 1 kΩ Min. admissible load resistance: R l = 1 kΩ Max. admissible load capacity: C l = 1 nF Max. admissible load capacity: C l = 1 nF Max. admissible load inductance: L l = 100 nH Max.
Flow Meter FC01-LQ Flow Meter FC01-LQ Resistive load Resistive load Max. admissible switching capacity: 50 W Max. admissible switching capacity: Max. admissible switching current: 1A Max. admissible switching current: 50 W 1A Max. admissible continuous current: 1A Max. admissible continuous current: 1A Max. admissible switching voltage: 50 V Max.
Flow Meter FC01-LQ Flow Meter FC01-LQ Resistive load Resistive load Max. admissible switching capacity: 1.5 W Max. admissible switching capacity: Max. admissible switching current: 150 mA Max. admissible switching current: 1.5 W 150 mA Max. admissible switching voltage: 36 V Max. admissible switching voltage: 36 V Inductive load - L < 100 mH (DC voltage - without external safety circuit) Inductive load - L < 100 mH (DC voltage - without external safety circuit) Max.
Flow Meter FC01-LQ Flow Meter FC01-LQ 8.5 Metrological data 8.5 Metrological data 8.5.1 Flow rate measurement 8.5.1 Flow rate measurement Measuring is possible up to the flow rates indicated in the display range. However, the indicated accuracy is no longer guaranteed. The repeatability value remains valid. Measuring is possible up to the flow rates indicated in the display range. However, the indicated accuracy is no longer guaranteed. The repeatability value remains valid. 8.5.1.
Flow Meter FC01-LQ Inner pipe diamater D in mm Measuring range in m3/h Flow Meter FC01-LQ Display range in m3/h Inner pipe diamater D in mm Measuring range in m3/h Display range in m3/h 50 21 28 50 21 80 55 70 80 55 70 100 85 110 100 85 110 150 190 250 150 190 250 200 340 450 200 340 450 250 530 700 250 530 700 350 1040 1380 350 1040 1380 500 2120 2830 500 2120 2830 Setting range for internal pipe diameter: 50.0 mm … 999.
Flow Meter FC01-LQ Flow Meter FC01-LQ 8.5.2 Temperature measurement: Measuring range: Accuracy: 8.5.2 Temperature measurement: -40 °C … +130 °C Measuring range: ±1% MB *** Accuracy: -40 °C … +130 °C ±1% MB *** 8.5.3 Electronic control unit FC01-LQ 8.5.3 Electronic control unit FC01-LQ Temperature drift: 0.1%/K/MBE * Temperature drift: 0.1%/K/MBE * Heating up period until full accuracy is reached: 15 min. Heating up period until full accuracy is reached: 15 min.
Flow Meter FC01-LQ Flow Meter FC01-LQ 8.6 Sensor interface 8.6 Sensor interface 8.6.1 Electrical data of the terminal for calorimetric monitoring heads 8.6.1 Electrical data of the terminal for calorimetric monitoring heads Terminal Mnemonics Data Terminal Mnemonics Data XSK1 R(HEIZ)-LO Function: terminal for negative pole of heater element Drain output of heating current control Max. sink current: Isink = 88 mA Dielectric strength: -0.
Flow Meter FC01-LQ Flow Meter FC01-LQ 9 Accessories 9 Accessories No. Accessory Ordering configuration 1 surface mounted housing FC01-LQ-FH 2 front mounted housing FC01-LQ-ST 3 connecting cable for calorimetric monitoring head cable type LifYCY 4 x 2 x 0.2 mm 2 No. Accessory 1 surface mounted housing FC01-LQ-FH 2 front mounted housing FC01-LQ-ST 3 connecting cable for calorimetric monitoring head cable type LifYCY 4 x 2 x 0.
Flow Meter FC01-LQ Flow Meter FC01-LQ
Flow Meter FC01-LQ Flow Meter FC01-LQ Index Index A A ANA OUT FLOW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35, 40 ANA OUT FLOW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35, 40 ANA OUT TEMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35, 40 ANA OUT TEMP . . . . . . . . . . . . . . . . . . . . . . . . . . .
Flow Meter FC01-LQ Flow Meter FC01-LQ M M Main menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26, 29 Main menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26, 29 MEAS. TIME MEAS. TIME . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Appendix 1 OFF OFF OFF OFF OFF Error No. 2 Error No. 3 Error No. 4 Error No. 5 Heating period active X X X Error No. 60 * Error No. 40 Error No. 41 Y Y OFF OFF OFF OFF OFF ON ON ON ON OFF OFF OFF OFF OFF OFF ON NO ERROR ON ON FA ON OFF ON OFF OFF OFF ON OFF OFF OFF OFF OFF OFF OFF ON NOT BUSY and FREQUENCY OUTPUT * When frequency output has been selected.
Flow Meter FC01-LQ Flow Meter FC01-LQ
Flow Meter FC01-LQ Appendix 2 - Menu structure of the FC01-LQ (operator dialog) POWER ON! LS1 → F / LS2 → F LS1 → T / LS2 → F LS1 → F / LS2 → T LS1 → T / LS2 → T HEATING UP ▲+▼ 12.5 m/s -13.5°C MAIN MENU M PEAK VALUE MIN M PEAK VALUE MAX DELETE totalized quantity DELETE MIN VALUE M PARAMETERS M DELETE MAX VALUE M M CODE T xxx M M DN25 (1 in) DN32 (1.1/4 in) DN40 (1.
