Technical data

Flow Meter FC01-Ex Flow Meter FC01-Ex
38 Operation 38 Operation
5.1.1.5 Limit switch combinations (menu option: LIMIT SWITCHES)
The FC01-Ex comprises two limit switches which are assigned to the physical quanti-
ty/quantities to be monitored in menu “LIMIT SWITCHES”.
The following four combinations are available:
* LS1  F LS2  F
Limit switch 1  flow rate
Limit switch 2  flow rate
* LS1  T LS2  T
Limit switch 1  medium temperature
Limit switch 2  medium temperature
* LS1  F LS2  T
Limit switch 1  flow rate
Limit switch 2  medium temperature
* LS1  T LS2  F
Limit switch 1  medium temperature
Limit switch 2  flow rate
Mode of operation, limit value and hysteresis of the limit switches are set in menu “PARAMETER
SELECTION”.
Caution!
Menu option “LIMIT SWITCHES” may influence data in the parameter selection menu (see
para. 5.1.1.14, Quitting the configuration menu).
5.1.1.6 Flow rate unit (menu option: FLOW UNIT)
This menu option is used to set the desired flow rate unit:
* METRE/SEC [m/s] * FEET/SEC. [FPS]
* PERCENT [%] * BLANK [no unit]
Any further entries relating to flow rate (e.g. limit value, analogue output etc.) refer to that unit.
Standard percent is displayed when BLANK (no unit) is selected.
When the flow rate unit is changed, all configuration and parameter data relating to flow rate will
automatically be converted!
5.1.1.7 Medium temperature unit (menu option: TEMP. UNIT)
This submenu is used to select medium temperature unit.
Options are:
* GRAD CELSIUS [°C]
* GRAD FAHRENHEIT [°F]
* KELVIN [K]
All other entries relating to the medium temperature (limit value, analogue output etc.) refer to
the unit selected there. When the temperature unit is changed, all configuration and parameter
data relating to medium temperature will automatically be converted.
5.1.1.5 Limit switch combinations (menu option: LIMIT SWITCHES)
The FC01-Ex comprises two limit switches which are assigned to the physical quanti-
ty/quantities to be monitored in menu “LIMIT SWITCHES”.
The following four combinations are available:
* LS1  F LS2  F
Limit switch 1  flow rate
Limit switch 2  flow rate
* LS1  T LS2  T
Limit switch 1  medium temperature
Limit switch 2  medium temperature
* LS1  F LS2  T
Limit switch 1  flow rate
Limit switch 2  medium temperature
* LS1  T LS2  F
Limit switch 1  medium temperature
Limit switch 2  flow rate
Mode of operation, limit value and hysteresis of the limit switches are set in menu “PARAMETER
SELECTION”.
Caution!
Menu option “LIMIT SWITCHES” may influence data in the parameter selection menu (see
para. 5.1.1.14, Quitting the configuration menu).
5.1.1.6 Flow rate unit (menu option: FLOW UNIT)
This menu option is used to set the desired flow rate unit:
* METRE/SEC [m/s] * FEET/SEC. [FPS]
* PERCENT [%] * BLANK [no unit]
Any further entries relating to flow rate (e.g. limit value, analogue output etc.) refer to that unit.
Standard percent is displayed when BLANK (no unit) is selected.
When the flow rate unit is changed, all configuration and parameter data relating to flow rate will
automatically be converted!
5.1.1.7 Medium temperature unit (menu option: TEMP. UNIT)
This submenu is used to select medium temperature unit.
Options are:
* GRAD CELSIUS [°C]
* GRAD FAHRENHEIT [°F]
* KELVIN [K]
All other entries relating to the medium temperature (limit value, analogue output etc.) refer to
the unit selected there. When the temperature unit is changed, all configuration and parameter
data relating to medium temperature will automatically be converted.