Technical data

Flow Meter FC01-Ex Flow Meter FC01-Ex
42 Operation 42 Operation
5.1.1.13 Analogue output - medium temperature (menu option: ANA OUT TEMP.)
In conformance with the configuration “Flow rate analogue output” it is possible to adjust the
medium temperature analogue output to the requirements of the entire system.
Options are:
* OFFSET = % (FS) (0/4 … 20 mA, 0/1 … 5 V, 0/2 … 10 V)
* ZERO = (initial value 0(20) % corresponds to a medium temperature of … [°C] [°F] [K])
* FS = (final value 100% corresponds to a medium temperature of … [°C] [°F] [K])
When entering the initial or final value, the user should observe a reasonable resolution.
5.1.1.14 Quitting the configuration menu
Upon configuration of the analogue outputs, the menu may be quitted or reset to the start (SENSOR
SELECT).
To quit the configuration menu, the controller will check the data entered for plausibility.
“CONFIG. OK!” is indicated when the data are found to be correct. The menu may then be quitted
by pressing M MODE.
Errors found during the plausibility check are indicated in the following sequence of priority.
Priority of entry errors in the CONFIGURATION menu:
* ERR. A-OUT FLOW OUT OF RANGE
(flow analogue output outside measuring range)
* ERR. A-OUT FLOW ZERO ≥ FS
(initial value ≥ final value with flow analogue output)
* ERR. A-OUT TEMP. OUT OF RANGE
(temperature analogue output outside measuring range)
* ERR. A-OUT TEMP. ZERO ≥ FS
(initial value ≥ final value with temperature analogue output)
* ERR. BARGRAPH OUT OF RANGE
(bar value outside measuring range)
* ERR. BARGRAPH ZERO ≥ FS
(bar initial value ≥ bar final value)
The menu can only be quitted after correction of the error(s). To do this, return to the beginning
of the configuration menu by pressing ▼ DOWN or ▲ UP and select the menu option with the
incorrect entry for correction.
Caution!
If during the configuration data are affected which are accessible in the parameter selection
menu (which may be the case for the options Medium Selection and Limit Switch
Assignment), the option “PARAMETERS” in the main menu will be flashing.
In this event it is imperative to branch into parameter selection menu to set the data in
conformance with the desired application.
5.1.1.13 Analogue output - medium temperature (menu option: ANA OUT TEMP.)
In conformance with the configuration “Flow rate analogue output” it is possible to adjust the
medium temperature analogue output to the requirements of the entire system.
Options are:
* OFFSET = % (FS) (0/4 … 20 mA, 0/1 … 5 V, 0/2 … 10 V)
* ZERO = (initial value 0(20) % corresponds to a medium temperature of … [°C] [°F] [K])
* FS = (final value 100% corresponds to a medium temperature of … [°C] [°F] [K])
When entering the initial or final value, the user should observe a reasonable resolution.
5.1.1.14 Quitting the configuration menu
Upon configuration of the analogue outputs, the menu may be quitted or reset to the start (SENSOR
SELECT).
To quit the configuration menu, the controller will check the data entered for plausibility.
“CONFIG. OK!” is indicated when the data are found to be correct. The menu may then be quitted
by pressing M MODE.
Errors found during the plausibility check are indicated in the following sequence of priority.
Priority of entry errors in the CONFIGURATION menu:
* ERR. A-OUT FLOW OUT OF RANGE
(flow analogue output outside measuring range)
* ERR. A-OUT FLOW ZERO ≥ FS
(initial value ≥ final value with flow analogue output)
* ERR. A-OUT TEMP. OUT OF RANGE
(temperature analogue output outside measuring range)
* ERR. A-OUT TEMP. ZERO ≥ FS
(initial value ≥ final value with temperature analogue output)
* ERR. BARGRAPH OUT OF RANGE
(bar value outside measuring range)
* ERR. BARGRAPH ZERO ≥ FS
(bar initial value ≥ bar final value)
The menu can only be quitted after correction of the error(s). To do this, return to the beginning
of the configuration menu by pressing ▼ DOWN or ▲ UP and select the menu option with the
incorrect entry for correction.
Caution!
If during the configuration data are affected which are accessible in the parameter selection
menu (which may be the case for the options Medium Selection and Limit Switch
Assignment), the option “PARAMETERS” in the main menu will be flashing.
In this event it is imperative to branch into parameter selection menu to set the data in
conformance with the desired application.