OWNER’S MANUAL CONDITIONED POWER DISTRIBUTION SEQUENTIAL POWER UP / POWER DOWN 1450 Lakeside Drive• Waukegan, Illinois 60085 USA 330-677-4424 • 800-321-6699 • Fax: 330-677-4471 http://www.etasys.com E-mail eta@etasys.com All designs and specifications are subject to change without notice. Copyright © 2006 ETA Systems.
ETA’s line of Conditioned Power Distribution units are designed to reduce damage to sensitive electronic equipment from sudden voltage spikes, damaging power surges, and EMI/RFI noise, which is inherent in utility power lines. The PD11SP is a sequential four step/stage power up/down conditioned power distribution unit.
The PD11SS is a sequential four step/stage power up/down conditioned power distribution unit. It is designed to protect electronic equipment that requires a time-delayed start-up, particularly when high in-rush current can potentially damage audio, video, or computer equipment at power up.
PD11P, PD11VP, PD11LP, PD11LVP Features: • Light Switch (PD11LP/LVP/LVSP) activates rack illumination; choice of HI or LOW intensity • Light Tubes (PD11LP/LVP/LVSP) illuminates up to 25 rack spaces • 4 dual 20 amp U-grounded switched outlets per unit • 1 dual 15 amp U-grounded "always on" and protected outlet • Digital Voltmeter Readout (PD11VP/LVP/LVSP) displays incoming line voltage • Resettable 20 amp thermal circuit breaker; 15 amp for front panel outlet • Lighted Outlet Power Switch activates protectio
Installation Requirements PD11P, PD11VP, PD11LP, PD11SP, PD11LVP, PD11LVSP Plug unit into power source and observe status of four "Protection" light emitting diodes. The (green) “1st Stage”, “2nd Stage”, and “GROUND OK” L.E.D.’s should normally be illuminated and the (red) “FAULT” L.E.D. should be off. When these indications are present, test the power “On/Off” switch which will illuminate to indicate that power is being supplied to the switched outlets on the rear of the unit. A.
Three-Wire Remote Control Interface A three-wire remote control interface is added to the main PC board for the PD11SS, PD11SP AND PD11LVSP units. This remote control interface is accessible through an external terminal block on the back of the unit (see Figure 6). This interface requires an external user provided switch, L.E.D., and a three-wire cable to implement. The interface has been tested reliably over 1000 feet with 22-gauge speaker wire (see Figures 1 and 5).
ETA Conditioned Power Distribution... The Benchmark By Which Professionals Compare. For over 20 years ETA has developed, manufactured, and sold high amperage theatrical lighting systems from which have evolved an extensive line of rack mounted conditioned power distribution products designed to protect today’s sensitive electronic digital equipment.
Addendum NOTE: The following pages are added as an addendum to the ETA manual. For most reliable performance of ETA Systems sequencing products, it is recommended that you use one of the cable types illustrated in the following pages. When installing any cabling in a plenum or return air space, it is the responsibility of the installer to ensure that Teflon jacketed cable is used where required by fire codes.
8489 Non-Paired - Audio, Control and Instrumentation Cable For more information please call 1-800-Belden1 See Put-ups and Colors Related Documents : No. 1.pdf Description: 18 AWG stranded (19x30) tinned copper conductors, conductors cabled, PVC insulation, PVC jacket. PHYSICAL CHARACTERISTICS: CONDUCTOR: Number of Conductors 4 Total Number of Conductors 4 AWG 18 Stranding 19x30 Conductor Material TC - Tinned Copper INSULATION: Insulation Material PVC - Polyvinyl Chloride Nom.
8489 Non-Paired - Audio, Control and Instrumentation Cable Operating Temperature Range -20°C To +60°C UL Temperature Rating 60°C (UL AWM Style 2598) Bulk Cable Weight 44.1 lbs/1000 ft. Max. Recommended Pulling Tension 83 lbs. Min. Bend Radius (Install) 2.6 in.
8489 Non-Paired - Audio, Control and Instrumentation Cable © Copyright 2006 Belden, Inc All Rights Reserved. Although Belden ("Belden") makes every reasonable effort to ensure their accuracy at the time of this publication, information and specifications described herein are subject to error or omission and to change without notice, and the listing of such information and specifications does not ensure product availability.
COMMUNICATION & CONTROL UL TYPE CM UL AWM 2509, CSA CMG FT 4 RoHS COMPLIANT, 300 VOLT MULTICONDUCTOR, UNSHIELDED PVC/PVC CHARACTERISTICS 182 OPERATING TEMPERATURE: ■ –20°C to 80°C – AWM ■ 75°C – CM VOLTAGE RATING: ■ 300 Volt – CM ■ 150 Volt – CL2 COLOR DESCRIPTION: ■ Color Code: Chart D Page 375 ■ Jacket Color: Gray PRODUCT DESCRIPTION: ■ Conductor: Stranded Tinned Copper ■ Insulation: Color-Coded PVC ■ Jacket: PVC SPECIFICATIONS ■ ■ ■ ■ ■ ■ ■ UL Type CM, AWM 2509 (18 & 16 AWG) UL Type CL2, (14 & 12
