ETA-PD8 Power Conditioner & Distribution Unit ETA-PD8 Power Conditioner & Distribution Unit 1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A. Telephone: 800-321-6699 • Fax: 800-996-3821 –1– Specifications are subject to change without notice. ETAsys.
ETA-PD8 Power Conditioner & Distribution Unit TABLE OF CONTENTS Important Safety Instructions .................................................................................................................. 3 Introduction ............................................................................................................................................ 5 Key Features.....................................................................................................................................
ETA-PD8 Power Conditioner & Distribution Unit IMPORTANT SAFETY INSTRUCTIONS The lightning flash with arrowhead symbol within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage “ within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
ETA-PD8 Power Conditioner & Distribution Unit • • • • • • • • • • WARNING – WHEN THE DEVICE IS IN USE To prevent electric shock, do not remove the product cover as there are high voltage components inside. Refer all servicing to ETA Systems. Should any of the following irregularities occur during use, immediately switch off the power, disconnect the power cord from the AC outlet and contact ETA Systems.
ETA-PD8 Power Conditioner & Distribution Unit INTRODUCTION Thank you for purchasing the ETA Systems ETA-PD8 AC Power Conditioner & Distribution Unit. The ETA-PD8 has been designed to meet most installation requirements for AC power distribution and equipment power protection. The ETA-PD8 features noise filtering for unwanted Radio Frequency Interference (RFI) that is commonly introduced into AC lines by nearby radio transmitters or wireless products.
ETA-PD8 Power Conditioner & Distribution Unit FRONT PANEL FEATURES 1 2 3 1. Unswitched AC Outlet – The 120VAC outlet is always live when the ETA-PD8 power cord is plugged into an AC mains power source and voltage is present. Note: The AC mains power switch does not affect the Unswitched AC Outlet. The Unswitched Outlet is protected by the surge protection circuitry. 2. AC Mains Breaker – The 15A rated breaker will open if the combined draw of all AC outlets exceeds 15A.
ETA-PD8 Power Conditioner & Distribution Unit AC POWER CORD RETAINER SYSTEM Your ETA Systems product comes with an AC Mains Power Cord Retainer System. This system prevents the power cord from being removed without the use of a screwdriver. Follow these steps for installation. Note: Installation of this product must be done by a certified electrician for a permanently connected apparatus provided neither with an all-pole mains switch nor an all-pole circuit breaker.
ETA-PD8 Power Conditioner & Distribution Unit ETA-PD8 SPECIFICATIONS Type Power Conditioner & Suppressor Load Rating 15A Safety Listing ETL (UL 60065 Standard) Front Panel AC Outlets 1 Unswitched Activation Switch Rocker Circuit Breaker 15A Resettable Indicators AC Power On Rear Panel AC Outlets 8 Total, 6 Switched, 2 Unswitched AC Mains Power Cord 9' (3 Meters) 14-gauge Technical Data Current Rating 15 amps Power Consumption 6 watts Operating Voltage 102 - 132VAC Min.
ETA-PD8 Power Conditioner & Distribution Unit NOTES: 1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A. Telephone: 800-321-6699 • Fax: 800-996-3821 –9– Specifications are subject to change without notice. ETAsys.
ETA-PD8 Power Conditioner & Distribution Unit NOTES: 1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A. Telephone: 800-321-6699 • Fax: 800-996-3821 – 10 – Specifications are subject to change without notice. ETAsys.
ETA-PD8 Power Conditioner & Distribution Unit NOTES: 1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A. Telephone: 800-321-6699 • Fax: 800-996-3821 – 11 – Specifications are subject to change without notice. ETAsys.
ETA-PD8 Power Conditioner & Distribution Unit LIMITED WARRANTY All products manufactured by ETA Systems are warranted to the original dealer/installer, industrial or commercial purchaser to be free from defects in material and workmanship and to be in compliance with our published specifications, if any. This warranty shall extend from the date of purchase for a period of one year. Additionally, fuses and lamps carry no warranty.
