Source 4 WRD ™ HPL to LED Retrofit Installation and User Manual Version 1.1.0 Part Number: 7067M1200-1.1.
ET C ®, Source Four ®, Source 4 W R D ™, Sensor ®, and Unis on ® are either registered trademarks or trademarks of Electronic The atre Controls , Inc. in the United Sta tes a nd othe r countries. All other trademarks, both marked and not marked, are the property of their respective owners. This product is protecte d by one or more of the following U.S. Patents : US 9, 261,241 and 9,273,831. ETC intends this document, whether printe d or electronic, to be provided in its entirety.
Table of Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . 1 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Sensor dimmer settings . . . . . . . . . . . . . . . . . . 5 Color rendering and quality . . . . . . . . . . . . . . 6 Contacting ETC . . . . . . . . . . . . . . . . . . . . . 7 Retrofit kit installation . . . . . . . . . . . . . . . 8 Remove incandescent lamp housing . . . . . . .
Cleaning and maintenance. . . . . . . . . . . 15 Clean the fixture. . . . . . . . . . . . . . . . . . . . . . . 15 Store the retrofit . . . . . . . . . . . . . . . . . . . . . . 16 Clean the lenses . . . . . . . . . . . . . . . . . . . . . . . 16 Clean the reflector . . . . . . . . . . . . . . . . . . . . . 17 Clean 5° and 10° polymer lenses . . . . . . . . . .
Introduction Congratulations on your purchase of the ETC Source 4WRD LED retrofit kit. Replacing your existing incandescent burner assembly with the Source 4WRD LED brings a new tool to your lighting inventory. The Source 4WRD LED expands the options for existing Source Four® fixtures and adds a new white LED fixture to the ETC family.
Safety The Source 4WRD fixture is intended for professional use only. Read the entire manual before using this equipment. WARNING: Note the following safety warnings before use: • Do not mount the Source 4 WRD fixture on or near a flammable surface. • Do not use the Source 4 WRD fixture below 5°C (41°F). • Minimum storage temperature is 5°C (41°F). When the fixture has been stored or transported in cold temperatures, allow it to warm to room temperature for a minimum of 1 hour before applying power.
Note: • Maximum recommended ambient operating temperature: Ta=50°C (122°F) • Maximum anticipated external surface temperature: Tmax=63°C (145°F) at Ta=50°C (122°F) • External Temperature (steady state achieved) at 25°C (77°F) ambient: 38°C (100°F) User Manual 3
Specifications Typical Power Consumption Idle Power / Current DMX Mode: 1.2W/.046A; AC Mode: 0W Full Intensity Power / Current 155.7W/1.35A Physical • • • • • Rugged die-cast aluminum construction Advanced thermal management systems for long LED life Ambient operating temperature: 5°–50°C (41°F–122°F) Minimum storage temperature: 5°C (41°F) Weight: - Source 4WRD LED retrofit kit only: 3.65 lb (1.66 kg) - Source 4WRD LED installed on 26° fixture with yoke and C-clamp:14 lb (6.
Sensor dimmer settings The Source 4WRD fixture can be dimmed from a DMX source, an existing dimmer, or locally on the fixture. When powering a fixture with a CEM classic, CEM+, or CEM3 for DMX dimming or AC level setting, set the parameters as shown below to ensure that the dimmer is out of regulated mode. The following tables apply to ETC Sensor® control modules including CEM, CEM+, and CEM3. Note: You may need to adjust dimmer settings for optimal fixture control.
Note: With AC dimming (line-dimmed) mode, performance may vary based on the control settings of the dimmer used. For this reason, ETC recommends using AC dimming for level-setting or for architectural quality dimming situations. ETC recommends testing the Source 4WRD fixture on all existing dimmers you wish to use. Use DMX mode when high-performance, live, dynamic dimming is required. You may need to increase the SCR Off Time from the default setting.
Contacting ETC If you are having difficulties, your most convenient resources are the references given in this user manual. To search more widely, try the ETC website at etcconnect.com. If none of these resources is sufficient, contact ETC Technical Services directly at one of the offices identified below. Emergency service is available from all ETC offices outside of normal business hours.
Retrofit kit installation WARNING: RISK OF FIRE OR ELECTRIC SHOCK: Source 4 WRD LED retrofit kit installation requires knowledge of luminaire electrical systems. If not qualified, do not attempt installation. Contact a qualified electrician. Note: THE RETROFIT KIT IS ACCEPTABLE AS A COMPONENT OF A LUMINAIRE WHERE THE SUITABILITY OF THE COMBINATION SHALL BE DETERMINED BY AUTHORITIES HAVING JURISDICTION.
Install Source 4 WRD retrofit WARNING: RISK OF FIRE OR ELECTRIC SHOCK: Install this kit only onto luminaires that have the construction features and dimensions shown in the images in this document and where the input rating of the retrofit kit does not exceed the input rating of the luminaire. WARNING: Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation. CAUTION: Do not touch or clean LED optic domes with anything other than oil-free canned air.
Fixture installation The Source 4WRD Light Engine combines the classic form factor of the Source Four incandescent fixture with an LED light source. The Source 4WRD Light Engine includes an adjustable yoke, C-clamp, and attached power lead.
Connect cables The fixture can be controlled by AC power or DMX. The fixture responds to the control method selected using the user interface. For more information, see User interface on page 12. Note: Make sure your dimmer is out of regulated mode for optimum performance. See Sensor dimmer settings on page 5 for recommended dimmer settings. Note: Connecting both power and data from a SmartBar 1 to a Source 4WRD fixture may cause flickering.
DMX pinout Pin Description Pin Description 1 DMX + 5 Not Connected 2 DMX - 6 Not Connected 3 Not Connected 7 Iso Common (Shield) 4 Not Connected 8 Not Connected User interface The two-button, seven-segment display shows the DMX address, AC mode, or the manually-set level. • Set a DMX address: Use the up and down arrows to navigate to the desired DMX address number (1–512). • Set the fixture to AC mode: Use the down arrow to navigate one number below DMX address 1.
Error codes The following error codes may be seen on the Source 4WRD user interface. • indicates the fixture has gone into over-temperature protection. Reset the fixture to clear the code. - For DMX mode: Return the DMX control to 0. - For AC mode: Remove the fixture from power for five seconds and then restore power. • indicates the fixture has gone into under-temperature protection. Allow the fixture to warm to a minimum of 5°C (41°F). • Flashing DMX address indicates loss of DMX.
Adjust the yoke position Change the height position 1: 2: 3: 4: Remove the yoke locking knobs, washers, and hex bolts from either side of the fixture. Raise or lower the fixture to the desired position within the yoke. Reinstall the yoke’s hex bolts, washers, and locking knobs. Tighten the yoke knobs to secure in position. Low clearance position General use position Set the angle within the yoke 1: 2: 3: Loosen the yoke locking knob. Do not remove the knob. Tilt the fixture to the desired position.
Use a pattern The pattern holder slot is on the top side of the barrel and in front of the shutters. It accommodates A-size, B-size, and glass pattern holders. A-size pattern holder: Holds 3” diameter patterns 3.12" Diameter 2.75" Diameter B-size pattern holder: Holds 2.5” and 2.75” diameter patterns 3.70" 3.70" Note: Because the Source 4WRD aperture is 3 inches wide, ETC recommends using A-size patterns for maximum pattern effectiveness.
Store the retrofit • Store the Source 4WRD LED at temperatures of 5°C (41°F) or higher. • If you must store the Source 4WRD LED below 5°C (41°F), make sure it is in an upright position as shown to the right. Allow it to warm to room temperature for a minimum of one hour before applying power. Store with LED dome up Note: After shipping or storing the Source 4WRD LED below 5°C (41°F), visually inspect the unit to ensure the low temperatures have not caused cracking of the LED array.
Clean the reflector WARNING: Unplug the fixture before attempting to clean the reflector. To quickly clean the reflector, remove the lens tube and clean the dust from the reflector with a blast of oil-free air. You may also wipe the reflector with a clean lint-free cloth. If either method is not sufficient, follow these steps.
Clean 5° and 10° polymer lenses To quickly clean the lenses, remove dust with a blast of oil-free air. If this is not sufficient, follow these steps. CAUTION: Handle polymer lenses by their edges only. Never rub anything dry on a polymer lens. 1: 2: 3: 4: 5: 6: 7: 8: 9: 10: 18 Remove the beam focus knob at the bottom of the barrel. Remove the lens tube from the barrel. Use a Phillips screwdriver to remove the brackets that hold the lens in place. Remove the lens from the tube.
User Manual 19
Corporate Headquarters Middleton, Wisconsin, USA Tel +608 831 4116 Service (Americas) service@etcconnect.com London, UK Tel +44 (0)20 8896 1000 Service: (UK) service@etceurope.com Rome, IT Tel +39 (06) 32 111 683 Service: (UK) service@etceurope.com Holzkirchen, DE Tel +49 (80 24) 47 00-0 Service: (DE) techserv-hoki@etcconnect.com Hong Kong Tel +852 2799 1220 Service: (Asia) service@etcasia.com Web: etcconnect.com Copyright © 2017 Electronic Theatre Controls, Inc. All Rights Reserved.