ETC S4 User Manual

ManualsBrandsETC ManualsLighting & StageHot Spot Housing

Source Four User Manual • 1

Source Four

User Manual

HPL lamps

Do not use lamps other than the HPL in Source Four ﬁxtures.

Use of lamps other

than HPL will void UL/cUL safety compliance and your warranty

Lens locations

The different lenses used in the

Source Four are not interchangeable.

When installing a new lens, refer to

the illustration below for proper

placement. Also, remember to have

the lens’ color designator dot facing

the color frame.

Lamp code Watts Volts Initial Lumens Color temp. Average rated life

HPL 750/115

750 115 21,900 3,250º K 300 hour

HPL 575/115 575 115 16,520 3,250º K 300 hour

HPL 575/115X 575 115 12,360 3,050º K 2,000 hour

HPL 575/120 575 120 16,460 3,250º K 300 hour

HPL 375/115 375 115 10,540 3,200º K 300 hour

HPL 375/115X 375 115 8,068 3.000º K 1000 hour

HPL 550/77* 550 77 16,170 3,250º K 300 hour

HPL 550/77X* 550 77 12,160 3.050º K 2,000 hour

HPL 750/220 750 220 19,400 3,200º K 300 hour

HPL 750/230 750 230 19,400 3,200º K 300 hour

HPL 750/240 750 240 19,400 3,200º K 300 hour

HPL 575/230 575 230 14,900 3,200º K 400 hour

HPL 575/240 575 240 14,900 3,200º K 400 hour

HPL 575/230X 575 230 11,780 3,050º K 1500 hour

HPL 575/240X 575 240 11,780 3,050º K 1500 hour

HPL 375/230X 375 230 7,800 3,050º K 1000 hour

HPL 375/240X 375 240 7,800 3,050º K 1000 hour

Table 1:

HPL lamp reference

*To be used with ETC Dimmer Doubler™

19° (6x16)

Red dot

26° (6x12)

Black dot

36° (6x9)

Dotless

50° (4.5x6)

Yellow dot

Figure 1

Retainin

cli

Color frame holder

Color frame

Drop-in iris slot

Pattern holder slot

Shutters

Retainer bolt

Yoke

Insulated handle

Yoke locking knob

Barrel rotation knob

Barrel

Beam focus knob

Lens tube

Reflector housing

Lamp housing

Note:

Safety cable is included

for cUL applications.

Summary of content (8 pages)

PAGE 1
Source Four User Manual ª Lamp housing Reflector housing Yoke Retainer bolt Shutters Pattern holder slot Drop-in iris slot Insulated handle Yoke locking knob Color frame Barrel rotation knob Color frame holder Barrel Beam focus knob Lens tube Note: Safety cable is included for cUL applications. Retaining clip HPL lamps Do not use lamps other than the HPL in Source Four fixtures. Use of lamps other than HPL will void UL/cUL safety compliance and your warranty.
PAGE 2
Installing or replacing the HPL lamp HPL Lamp A lamp must be installed before you use the fixture. Note: Verify that the HPL lamp you intend to install is suitable for your facility's voltage; 115-, 120-, 230-, and 240-volt HPL lamps are available. See the above table. Operating HPL lamps above their rated voltage reduces lamp life and can cause premature lamp failure. Lamp base Replace the lamp if it becomes damaged or thermally deformed. WARNING! Let the lamp cool before replacing.
PAGE 3
Color frame retaining clip Retaining clip in the locked position The color frame holder is equipped with a spring-loaded retaining clip that prevents color frames and accessories from falling out (Figure 5). WARNING! Make sure all color frame accessories are locked in position with the retaining clip before hanging the Source Four. 1. Release the retaining clip by pushing it sideways while gently pulling backwards. Figure 5 2. Insert the color frame. 3.
PAGE 4
Rotating the barrel assembly 1. Loosen the barrel rotation knob directly behind the shutters on the underside of the reflector housing (Figure 8). Do not remove the barrel rotation knob. 2. Rotate the barrel to the desired position (up to 25° in either direction from the centered position). 3. Once the barrel is positioned, tighten the barrel's rotation knob to lock it into position.
PAGE 5
Cleaning ETC offers the following recommendations when cleaning and inspecting lenses and reflectors: Do not use glass or window type cleaners on lenses (glass or polymer) or reflectors. Do not use abrasive materials such as steel wool. Replace lenses if they contain visible damage (cracks or deep scratches) that may impair their effectiveness. Cleaning 19°, 26°, 36°, and 50° glass lenses 1. Remove the beam focus knob at the bottom of the barrel. Remove the lens tube from the barrel.
PAGE 6
Cleaning the reflector WARNING! Unplug the fixture before attempting to clean the reflector. To quickly clean the reflector, remove the lens tube and clean the dust from the reflector with a blast of oil-free air. You may also wipe the reflector with a clean lintfree cloth. If either method is not sufficient, follow the instructions below. You will need a Phillips screwdriver to complete this procedure. 1. Remove the barrel rotation knob located at the bottom of the barrel.
PAGE 7
Source Four User Manual • 7
PAGE 8
Electronic Theatre Controls North America 3030 Laura Lane • Middleton, Wisconsin 53562 • USA • Tel: (+1) 608 831 4116 • Fax: (+1) 608 836 1736 Europe 5 Victoria Industrial Estate • Victoria Road • London W3 6UU • Tel: (+44) 181 896 1000 • Fax: (+44) 181 896 2000 Asia Room 605-606 • Tower III • Enterprise Square • 9 Sheung Yuet Road • Kowloon Bay • Hong Kong • Tel: (+852) 2799 1220 • Fax: (+852) 2799 9325 World Wide Web: http://www.etcconnect.com • Email: mail@etcconnect.com Specifications subject to change.