CE User Manual Revision B Copyright © 2013 Electronic Theatre Controls, Inc. All Rights reserved. Product i nformation and specifications subj ect to change.
Ta b l e o f C o n t e n t s Source Four Mini CE Guidelines . . . . . . . . . . . . . . . . . . . . . . 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Basic Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Install Lens Tube . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Adjustments. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Adjusting the yoke position . . . . . . . . . . . .
DECLARATION OF CONFORMITY We, Electronic Theatre Controls Limited declare under sole responsibility that the product: Product name: Source Four Mini luminaire Product type/model: Source Four Mini Canopy mount, Source Four Mini Track mount & Source Four Mini Clamp mount. Versions fitted with tungsten lamp. Item numbers: One sample of each type to which this declaration relates is in conformity with the following Standards: EN 60598-1:2008 Luminaires.
Source Four Mini CE Guidelines Read the entire User Manual before using the equipment. WARNING: Please note the following safety precautions: • Do not mount the Source Four Mini CE on or near a flammable surface. • The Source Four Mini CE is suitable for indoor use only with a maximum ambient temperature: 40°C. • Maximum exterior surface temperature: 125°C. • Relative humidity 90% maximum, non-condensing • If the external cable is damaged, it shall be replaced by ETC or our service agents.
Introduction The Source Four Mini has four field-angle choices and comes in a portable version with a yoke mounted transformer, a canopy-mount design with an integral transformer, and a track-mount design with an integral transformer. Surprisingly bright for its size, the Mini offers crystal-clear image projection and a bright, even field. Portable Canopy Track There are three versions of the Source Four Mini. This manual covers common features for all versions.
Basic Assembly Yoke Lamp housing Gobo Pattern Holder Slot Lens tube Lamp housing knob Shutter Barrel Colour frame retainer clip Colour frame Beam focus knob Shutters x4 INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS IMPORTANT SAFETY INSTRUCTIONS Lighted lamp is HOT! WARNING - To reduce the risk of FIRE, ELECTRIC SHOCK, EXPOSURE TO EXCESSIVE UV RADIATION, OR INJURY TO PERSONS: 1) Turn off/unplug and allow to cool before replacing lamp.
I n s t a l l L e n s Tub e A lens tube must be installed prior to use of the Source Four Mini. There are four lens tubes available; 19°, 26°, 36°, and 50°. Beam focus knob Step 1: Step 2: Step 3: Unscrew the beam focus knob from the loose lens tube. Slide the lens tube into the shutter barrel. Install the beam focus knob. Adjustments Adjusting the yoke position The Source Four Mini provides multi-positioning capabilities within its yoke for overall luminaire angle.
L o c k i n g th e r o t a ti o n i n t h e c a n o p y a n d t r a c k - m o u n t v a r i a t i o n s Yoke lock Step 1: Step 2: Step 3: Rotate the luminaire into the desired position. Luminaire will be prevented from rotating completely around to protect the wiring. Insert a 1.5mm Allen wrench into the small hole on the yoke lock. Turn wrench to tighten down the yoke lock. F oc u s i n g t h e b e a m Step 1: Step 2: Step 3: Loosen the beam focus knob located under the barrel.
G o b o P at t e r n P r o j ec ti o n The Source Four Mini has a gobo holder slot on the top side of the shutter barrel, in front of the shutter. It accommodates a E-size (37.5mm with a 25.4mm image area) gobo pattern holder. Use an optional donut in the colour frame holder to enhance pattern projection. When the slot is not in use, a small sheet metal cover secured with a Phillips screw prevents light leakage. Step 1: 2.
Replacing the Lamp Lamp housing Lamp housing knob Step 1: Step 2: Step 3: Step 4: Step 5: Step 6: Step 7: Disconnect power to the Source Four Mini before installing the lamp. Loosen the brass lamp housing knob on the back of the lamp housing. The knob is not captured so it may come loose from the luminaire. Pull the lamp housing away from the luminaire body. Pull on the lamp carefully to remove it from the lamp housing. Gently push down on the replacement lamp until it is seated in place.
Cleaning the Glass Lens WARNING: Step 1: Step 2: Step 3: Step 4: Step 5: 8 Do not use ammonia-based or other harsh commercial cleaners. Clean lens only as directed. Commercially available glass cleaning agents should be avoided as they may contain ammonia, other harsh chemical detergents, or abrasive agents. These cleaners may damage the glass surface and the Anti-Reflective coatings. Do not immerse or soak the glass in any cleaning solution. Remove the beam focus knob from the barrel.
Corporate Headquarters 3031 Pleasant View Road, P.O.