Source Four LED Mini User Manual Part Number: 7063M1220 Rev G Released: 2021-10
To view a list of ETC trademarks and patents, go to etcconnect.com/ip. All other trademarks, both marked and not marked, are the property of their respective owners. ETC intends this document, whether printed or electronic, to be provided in its entirety.
Table of Contents Introduction Safety Installation 1 2 4 Install a Lens Tube 4 Install Track-Mounted Fixture 4 Install Canopy Fixture 6 Install Portable Fixture with C-clamp (120 V Only) 7 Focus and Setup 8 Adjust the Tilt 8 Lock the Rotation (Canopy and Track-Mount) 9 Focus the Beam 9 Shape the Beam 9 Use the Color Frame Holder Cleaning Source Four LED Mini User Manual 10 11 i
ii Source Four LED Mini User Manual
Introduction The Source Four LED Mini has three available mounting options: Portable: Includes a miniature C-clamp and yoke-mounted driver, and has a permanently installed power cord with 3-prong Edison connector. Region-specific connectors are available. Contact ETC for available options. Use L5-15 plugs on branch circuits with L5-15 receptacles only. • Track-mount and Canopy: The track-mount fixture and canopy fixture both include an integral driver.
Yoke Pattern holder slot Shutter barrel Lens tube Color frame retainer clip Safety cable attachment point Color frame Beam focus knob Shutters x4 Safety WARNING: Note the following safety warnings before use: • • • • • Use the fixture in dry locations only, where humidity does not exceed 90 percent (non-condensing). Do not mount the fixture on or near a flammable surface. Check that the accessory holder is locked before mounting the fixture. Do not operate the fixture without a lens installed.
IMPORTANT SAFEGUARDS INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS • • • • • • Keep lamp away from materials that may burn. Do not touch hot lens, guard, or enclosure. Do not remain in light if skin feels warm. Do not look directly at lighted lamp. External temperature after 5 minutes of full-brightness operation: 50°C (122°F). External temperature when steady state is achieved: 67°C (152.6°F).
Installation Install a Lens Tube You must install a lens tube before you use the Source Four Mini LED. There are four lens tube sizes available: 19°, 26°, 36°, and 50°. Lens Tube Description 4M19LT (-1, -5) 19° Source Four Mini Lens Tube Only Black (White, Silver) 4M26LT (-1, -5) 26° Source Four Mini Lens Tube Only Black (White, Silver) 4M36LT (-1, -5) 36° Source Four Mini Lens Tube Only Black (White, Silver) 4M50LT (-1, -5) 50° Source Four Mini Lens Tube Only Black (White, Silver) 1.
1. Insert the DataTrack adapter into the track. The adapter only fits into the track one way with the tabs nesting into the track’s groove. 2. Rotate the locking mechanism to lock the adapter into place. Tabs Lock Circuit selection wheel WARNING: When using the circuit selection lock, ensure that the selected circuit is a constant power circuit. Dialing into a dimmable circuit may cause fixture damage that will void the ETC warranty. 3. Use the circuit selection lock to select the circuit.
Install Canopy Fixture WARNING: RISK OF ELECTRIC SHOCK! Power must be off when you perform this procedure. The fixture must be installed by a qualified electrician in accordance with all national and local electrical and construction codes and regulations. AVERTISSEMENT : RISQUE DE DÉCHARGE ÉLÉCTRIQUE! L'alimentation doit étre éteinte avant d'exécuter cette procédure.
CAUTION: The canopy plate has built-in indentations allowing the mounting plate bolts to nest into the canopy plate. For an ideal flush-mount installation, you may need to rotate the plate to accommodate these indentations. See the following image. Mounting plate installation detail 1 Canopy bolt hole 2 3 3 2 Canopy bolt hole 1 Install the mounting plate screws in one of the three position-pairings shown. Only the slots on the outer circumference will allow a true flush mounting. 3.
Install Portable Fixture with C-clamp (120 V Only) C-clamp Pipe bolt Yoke bolt The C-clamp attaches the fixture to the mounting pipe and allows you to adjust the position of the fixture once it is mounted. The C-clamp will fit a 3/8” to 1” pipe. 1. Tightly fasten the C-clamp to the yoke with the provided yoke bolt and washers. 2. Place the C-clamp on the mounting pipe, and then tighten the pipe bolt to secure it. 3. Loosen the C-clamp yoke bolt and rotate the yoke to the desired position.
Lock the Rotation (Canopy and Track-Mount) Yoke lock 1. Rotate the fixture to the desired position. To protect the wiring, the fixture cannot rotate completely around. 2. Insert a 1.5 mm hex key into the small hole on the yoke lock, and turn it to tighten the yoke lock. Focus the Beam Loosen the beam focus knob, adjust the lens tube position as needed, and then tighten the knob. Shape the Beam Beam focus knob You can shape the beam using the four shutters or with a pattern.
Shape the Beam with a Pattern The fixture has a pattern-holder slot on the top side of the shutter barrel, in front of the shutter. It accommodates an E-size (37.5 mm with a 25.4 mm image area) pattern. Use an optional donut in the color frame holder to enhance pattern projection. When the slot is not in use, a small sheet metal cover secured with a Phillips screw prevents light leakage. 1 in Diameter 1. Use a Phillips screwdriver to loosen the screw on the slot cover. Do not remove the screw. 2.
1. Release the retaining clip by gently pushing it up. 2. Insert the color frame. 3. Lock the retaining clip by gently pushing it down. Retaining clip Color frame holder Cleaning WARNING: Do not use ammonia-based cleaners or other harsh commercial cleaners. Clean lens only as directed. Commercially available glass cleaning agents should be avoided as they may contain ammonia, other harsh chemical detergents, or abrasive agents. These cleaners may damage the lens surface.
Corpora te He a dqua rte rs n Middleton, WI, USA | +1 608 831 4116 Globa l Offic e s n London, UK | Rome, IT | Holzkirchen, DE | Paris, FR | Hong Kong Dubai, UAE | Singapore | New York, NY | Orlando, FL | Los Angeles, CA | Austin, TX We b etcconnect.com | Support support.etcconnect.com Conta c t etcconnect.com/contactETC | © 2021 Electronic Theatre Controls, Inc. Trademark and patent info: etcconnect.com/ip | Product information and specifications subject to change.
