CUBE5™ RGBWA LED User Manual (Battery Powered DMX LED Fixture) Please read over this manual before operating the light.
FIRST CHARGE YOUR FIXTURE FOR 6 HOURS. Introduction Unpacking: Thank you for purchasing the CUBE4™ RGBW QUAD LED. Every CUBE5™ RGBWA LED has been thoroughly tested and has been shipped in perfect operating condition. Carefully check the shipping carton for damage that may have occurred during shipping. If the carton appears to be damaged, carefully inspect your fixture for any damage and be sure all accessories necessary to operate the unit has arrived intact.
Safety Precautions ● To reduce the risk of electrical shock or fire, do not expose this unit to rain or moisture. ● Do not spill water or other liquids into or on to your unit. ● Be sure that the local power outlet match that of the required voltage for your unit. ● Do not attempt to operate this unit if the power cord has been frayed or broken. Do not attempt to remove or break off the ground prong from the electrical cord.
LED is workable in 100-220V/50~60Hz. Because line voltage may vary from venue to venue, you should be sure your unit voltage matches the wall outlet voltage before attempting to operate you fixture. DMX Linking: To ensure proper DMX data transmission, when using several DMX fixtures try to use the shortest cable path possible. The order in which fixtures are connected in a DMX line does not influence the DMX addressing.
DMX Values and Functions 3CH, 4CH, 5CH, 8CH & 11CH Mode 5
Touch Buttons There are four touch buttons under the LED display: Menu, Down, Up, Enter. Normally, the LED will display the current DMX address code of the fixture. At this time, presses Menu to choose the function you want to set up. Press and hold Up or Down to fast scrolling within the menu options. When an option is flashing the LED display, press Enter to confirm and Menu to exit. LED Operation Menu: After initialization, the unit is ready for setting and working.
(1) Alpha-numeric display (3) Microphone (5) DMX-Out socket (7) Battery switch (9) Power socket and fuse holder (11) Mounting bracket (2) Touch switches (4) DMX-In socket (6) Power switch (8) GND (10) Fixation screw There are two buttons on the rear panel of the lighting. One is for power, and the other is for battery. ● When use the fixture with DMX, not battery, please switch the button for power to “on”, and switch the button for battery to “bat off”.
Results will vary based on brightness of LEDs ● It is suggested to charge the battery for at least 8 hours, which will extend the life span of the battery. ● At the bottom of the fixture, there is a little hole which is the indicating light for the charge. When charge the light, the indicating light will be in red, and when charged full, it will be in green.
(1) Antenna (3) Wireless indicator (2)Power switch for wireless receiver (4)ID code selector Product feature: 1. Product name：2.4G wireless DMX512 R/T molding board 2. Small size，Easy to suit for interior of accessed lighting 3. Single key to operate，tricolor LED displaying 4. Transmitting standard DMX512 protocol data of console，also can transmitting lighting and lighting DMX512 protocol data. 5. 126 channels jumping frequency automatically，high anti-jamming ability.
Compatible series product as follows: Wiresless transmitter Operating manual： 1. 2. ID code and LED color corresponding relationship： 1：RED 2：GREEN 3：RED+GREED 4：BLUE 5：RED+BLUE 6：GREEN+BLUE 7：RED+GREED+BLUE Press button on transmitter to select group to match corresponding color on the receiving fixture. 3. LED constant lit up：no DMX or wireless signal. Red LED flash：transmitting. Green LED flash：receiving RF frequency- - - - - - - - - - - - 2. 400-2.
use different ID value if you need use more than 1 group wireless net at same time in same place. 3. The red LED flashes when transmitter transmits DMX data by no interfered frequency section, then receiver changes communicated frequency section. Green LED flash till received corrected same ID value, LED flash more fast once DMX data more fast. 4.
For more information please contact Support by email at support@eternallighting.
