Eternal Lighting CUBEecho RGBWA User Manual 1 CUBEecho RGBWA Eternal Lighting February 2014
Introduction: Thank you for your purchase. The CUBEecho RGBWA LED is a DMX intelligent LED par light. This LED par light is lightweight and compact which makes is ideal for Mobile Entertainers. Unpacking: Thank you for purchasing the CUBEecho RGBWA light fixture. Every CUBEecho RGBWA has been thoroughly tested and has been shipped in perfect operating condition. Carefully check the shipping carton for damage that may have occurred during shipping.
How Long Does the Battery Last? The CUBEecho RGBWA will last up to 20 hours on a single full charge. It will depend on which LED colors and how many LED colors are being used at what intensity based on the (0-255) Scale. The (0-255) Scale you see on the push button display is directly related to the 0-255 scale you are using with a DMX controller or DMX software.
Welcome to Start Up ETERNAL LIGHTING Version Switch to Display RGBWA DMX addr DMX addr: 001-512 CH mode CH-mode: 3 / 4 / 5 / 8 / 11 Mast/Slave Mast / Slave Manual R/G/B/W/A (000-255) Pre-Set Color 01-31 Auto Auto Speed 01-08 Custom Color A Color Custom Color B Custom Color C SHND Custom Color D Custom Color E Sound 1 Sound Sound 2 Fade 01-10 (Fast to Slow) Boot time Operating Time Work time Total Operating Time Battery Capacity Battery Percentage Indicator (90-100% is Fully Charged, 20-
Menu: • • • • • • • • • Start Up – Welcome to Eternal Lighting DMX Address and Channel Mode – Press Enter to move up and down between DMX Addr and CH also press Enter to save a command. Master/Slave – Press Up or Down to change the command of Master or Slave, Enter to save the command. (NOTE: In order to use the IR Remote, put the CUBEecho in Master Mode. The CUBEecho will not respond to the IR Remote if it is in Slave Mode.
Transmitter ID Receiver LED Color 1 2 3 4 5 6 7 RED GREEN YELLOW BLUE PURPLE CYAN WHITE Transmission Power Level on XT-Mitter PRO: Displays current transmission power (1) 2dBm (Lowest), (2) 8dBm, (3) 14dBm, or (4) 20dBm (Highest). To change the transmission power level, use the “PA” button located on the front panel. Recommended is P4. The XT-Mitter PRO will start blinking RED (meaning transmitting signal) and all the Slave fixture(s) will start blinking GREEN (meaning receiving signal).
DMX Values and Functions: 3CH Mode Value RGBWA 4*5in1 CH1 0-255 RED Color dimmer (0-255) CH2 0-255 GREEN Color dimmer (0-255) CH3 0-255 BLUE Color dimmer (0-255) Value RGBWA 4*5in1 CH1 0-255 RED Color dimmer (0-255) CH2 0-255 GREEN Color dimmer (0-255) CH3 0-255 BLUE Color dimmer (0-255) CH4 0-255 WHITE Color dimmer (0-255) Value RGBWA 4*5in1 CH1 0-255 RED Color dimmer (0-255) CH2 0-255 GREEN Color dimmer (0-255) CH3 0-255 BLUE Color dimmer (0-255) CH4 0-255 WHITE Color
CH Mode Value RGBWA 4*5in1 CH1 0-255 RED Color dimmer (0-255) CH2 0-255 GREEN Color dimmer (0-255) CH3 0-255 BLUE Color dimmer (0-255) CH4 0-255 WHITE Color dimmer (0-255) CH5 0-255 Auto CH6 0-255 Auto Slow to Fast (0-255) CH7 0-255 R, G, B,W STROBE from slow to fast (0-255) CH8 0-255 SOUND (Off 0-15 ON 16-255) 11CH Mode Value RGBWA 4*5in1 CH1 0-255 RED Color dimmer (0-255) CH2 0-255 GREEN Color dimmer (0-255) CH3 0-255 BLUE Color dimmer (0-255) CH4 0-255 WHITE Color
