Stellar60 Spot - 60 Watt LED Moving Head Ste lla r60 Spot tt LID Moving Heed Spot support@EternalLighting.
T BLE OF CONTENTS PART 1 PRODUCT (GENERAL) 1.1--PRODUCT INTRODUCTION 1.2-PRODUCT OVERVIEW I.3-TECHNICAL SPECIFICATIONS 1.4--PHOTOMETRIC DATA 1.5-SAFETY WARNING 1 1. 1. 2. 3. 3. PART 2 INSTALLATION 2. 1-4,10 UNTING 2.2--SETTING UP(MASTER/SLAVE) 2.3--SETTING UP(DMX512 CONTROLLER) 4. 4. 5. 7 2.4--LED PCB REPLACEMENT 2.5-G080 REPLACEMENT 2.6--FUSE REPLACEMENT 6. 6. 7. PART 3 DISPLAY R1NEL OPERATION 3. 1--BASIC 3.2-MENU 3.3-INTRO 3.4--INVERT 3.5--RANGE 3.6--SPECIAL 3.7-EDIT 3.
PRODUCT(GENERAL) 1.1 PRODUCT INTRODUCTION This product isdesigned for indooruse only. Suitable for stage,bar or nightclub applications. Directinput of DMX512 signal allows thefixtures to be controlled from anyDMX512 controller. The fixture isfully programmable with one custom programavailable and is supplied with twoautomatic programs (all accessible from DMX512controller). This productcan be operatedas a single unit or with multiple units forlarge applications. 1.
1 3 PRODUCT SPECIFICATIONS Electrical •Voltage:AC 100-240V, 50/60Hz ♦ Rated Power:150W LED ♦ LED:1PC(60W white) ♦ Cooling:Forced air convection Optical System ♦ Focus:Electronic focus ♦ Dimmer:0-100% ♦ Strobe:0-20Hz ♦ Rotating 3-facet Prism Operation ♦ Control mode: DMX512/Master-Slave/Auto/C ustom/ Sound ♦ LCD display ♦ DIV1X512 Chs:11CHS/ 14CHS Pan/Tilt ♦ Pan 540° Tilt 270° ♦ Pan/Tilt speed ♦ User-selectable Pan/Tilt ranges ♦ Reverse Pan/Tilt movement Rotating Gobo ♦ 7 Gobo (interchangeable) ♦ Gobo-flow e
1.4 PHOTOMETRIC DATA 1056 470 264.4 169 2 1_127 I ■ ( ( ITT '11081 1.5 6(166 3) i 8(221 7) , 10 ( 277 ) '2 1'( 8o'r:se" te`.7).) ) )) SAFETY WARNING IMPORTANT: • This product must be installedby a qualifiedprofessional. • Always operatethe equipment asdescribed in the user manual. • A minimum distance of 0.5m must be maintainedbetween the equipment and combustible surface. • The product must always be placed in a well ventilated area.
2 INSTALLATION 2.1 MOUNTING: • The LED fixture can be operatedin any position at any angle. When mounted on a flat surface, the surface must be strong enough to support 10 times the weight of thefixture and stable so that there will be nodamage caused tothe fixture or surrounding people or objects because of movements of the fixture on the surface. • When the unit is mounted in a hanging position.the fixture isattached using the mounting brackets anda standard trussclamp or other clamping device.
2.2 SETTING UP (MASTER/SLAVE) When units are connected in seriesusing DMX512 signalcable connect the units as shown inthe diagram below • Connect the (male)3 pin connectorside of the DMX cable to the output (female)3 pin connector ofthe first (MASTER) fixture. • Connect the endof the cable coming from the MASTER fixture whichwill have a (female)3 pin connector to the input connector ofthe next fixture consisting of a (male) 3 pin connector.
2.6 FUSE REPLACEMENT • • • • Remove the safety cap by a screwdriver. Fetch the oldfuse from safetycap. Install a newfuse. Install the safety cap. 3 DISPLAY PANEL OPERATION 3.
• - 3.2 MENU MENU INTRO ) ADDRESS ) RESET ) -...
13 E ) STROBE TIME D efault II co (0002) USE ) DEFAULT ) NO YES NO YES ) NO ) YES ) 3.3 INTRO MENU ) ...Us ADDRESS ) itESET) RUN CHANNELS ) A1)11) AU -102) SOUND 1 ) SOUND 2 ) CUSTOM ) TEST ) SLAVE) DMX512 ) BASIC ) ADVANCED ) DISPLAY ) 60 CLOSE BRIGHT KEY 1.
3.4 Invert MENU Invert Pan Normal Revers e ) Norm al ) Reverse ) Color ) Step ) Linear ) Use • ) Tilt Lr.i. No Yes Invert] • Select [ Pan] / [ Tilt] to set [Normal] or [Reverse] • Select [ Color] to select thecolor wheel flowway [Step] or [linear] • Enter [ Use] and set [Yes] to run thenew setting 3.5 Range MENU J _.— Range P ta (000-255) ) P •Firist t ) 1000-255) ) Tistat ) T/Finish ) irmantr. (000-255) ) Use ) ) No Yes 3.
3.7 EDIT MENU EDIT m.-4,- Step ) (000-255) ) Pan ) (000-255) ) Tilt. J (000-255) ) (000-255) ) Speed Color ) --_--- (000-255) ) Cobol ) (000-255) ) Dobo2 ) (000-255) ) Gobo.rot ) (000-255) ) Prism ) (000-255) Focus ) (000-255) Dimmer ) (000-255) Strobe ) (000- ) Time I (000-255) Use ) tlo) Yes ) Edit ] • Enter the [ Edit ] mode to editthe custom programsby adjusting the value of [Step] , [Pan] , [Tilt] , [Speed] , [Color] , [Gobo 13 , [Gobo 2] , [Gobo.
4 USING A DMX51 2 CONTROLLER 4.1 BASIC ADDRESSING .• Connect all of the units in series using standard DMX512 signal cable . Set the DMX512 address inthe [DMA menu. • It is possible to havethe same DMX address or independent addresses for each fixture 4.2 6 CHANNEL ASSIGNMENT Note This product have two DMX512 channel configuration: . and BA Si EADVA'ICED] ADVANCED C HANNEL FUNCTION VALUE PAN 0 4=0 Mi6 0,5 t III. 0 C.
CHANNEL FUNCTION VALUE GOSONIHEEL 150080 SHAKE MIIII8II448IIM 4II °2 RMS2 ,°,532 U1 NO Gobs Gobot Gobo 2 Gobo 3 Gobs 4 Gobo 5 Gobo S Gobo 7 Shaking gobo 7 Shaking gobo ik Shaking gobo 5 Shaking gobo a Shaking gobo 3 Shaking gobo 2 Shaking gobs I Flowettect G080 ROTATION 9 0.3.
BASIC CHANNEL FUNCTION VALUE PAN 0,-, 255 0-540• TILT OP255 0-270' COLOR WHEEL 1' I NOD O- 88 88II NM Green Orange Blue Light blue Light Green Rainbow or linear effect FIXED GOBO WHEEL NO G080 GOBO t GOBO 2 GOEI0 3 G0804 0080 5 00806 GOBO 7 G0808 G0809 Shaking gobo 9 Shaking gobo 8 Shaking gobo 7 Shaking gobo 6 Shaking gobo 5 Shaking gobo 4 Shaking gobo 3 Shaking gobo 2 Shaking gobo I Flow effect GOBO WHEEL I SGOBO SHAH am N n amm lo mm8 m1 gpoim pgm m 5 While Red Yellow Magenta 4 USINGA DMX51
5.2 MAINTENANCE No 5 APPENDIX No ITEM Front lense corer 72 2 Prism 13 3 Motet ITEM Base fan Er a ;t PCB 15 Base corer LED PCB 17 ALP Heal 90li 18 Power socket On/Off 4 Moroi dryer PCB 5 Rotalion gobo wheel 6 7 socket B =.