Installation Guide

ManualsBrandsEti ManualsElectrical3 ft. T8 14-Watt Soft White Linear Fluorescent LED Tube Light Bulb

6/30/2013

ETi SSL Inc.

The Americas Headquarters

26650 Renaissance PKW, STE 6

Cleveland, OH 44128 Page 1 of 6

LED Tube Lamp (Linear Fluorescent Replacement) Retrofit Installation Instructions

The product package includes the following components:

1. Integral LED Lamp (1 unit)

2. Fixture Warning Label (1 - self-adhesive)

3. Installation Instructions (1 - 6 pages)

IMPORTANT SAFETY INSTRUCTIONS AND WARNINGS：

THIS PRODUCT SHALL BE INSTALLED IN ACCORDANCE WITH THE LATEST U.L. SAFETY, NEC AND/OR

LOCAL AUTHORITY HAVING JURISDICTION. INSTALLATION SHALL BE PERFORMED BY A QUALIFIED

ELECTRICIAN UNDERSTANDING THE CONSTRUCTION AND OPERATION OF THIS PRODUCT AND THE

ELECTRICAL REQUIREMENTS INVOLVED.

Risk of fire or electric shock: LED Retrofit Kit installation requires knowledge of luminaires electrical systems. If not

qualified, do not attempt installation. Contact a qualified electrician.

Only those open holes indicated in the photographs and/or drawings may be made or altered as a result of kit installation. Do

not leave any other open holes in an enclosure of wiring or electrical components.

Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation.

Do not install in a raceway or a luminaire marked for through branch wiring.

Risk of fire or electric shock: Use only on 120-277 VAC, 50/60Hz circuits. Installer shall verify operating voltage at the

luminaries prior to installation.

Risk of fire or electric shock: Install this kit only in the luminaires that have the construction features and dimensions

shown in the photographs and/or drawings below.

Summary of content (6 pages)

PAGE 1
6/30/2013 LED Tube Lamp (Linear Fluorescent Replacement) Retrofit Installation Instructions The product package includes the following components: 1. Integral LED Lamp (1 unit) 2. Fixture Warning Label (1 - self-adhesive) 3. Installation Instructions (1 - 6 pages) IMPORTANT SAFETY INSTRUCTIONS AND WARNINGS： THIS PRODUCT SHALL BE INSTALLED IN ACCORDANCE WITH THE LATEST U.L. SAFETY, NEC AND/OR LOCAL AUTHORITY HAVING JURISDICTION.
PAGE 2
6/30/2013 Minimum luminaire dimensions: Length x Width x Height Item No. One Lamp Fixture Two Lamp Fixture Three Lamp Fixture Four Lamp Fixture 23.8'' x 5.71'' x 2.7'' 23.8'' x 11.34'' x 2.7'' 23.8'' x 16.54'' x 2.7'' 23.8'' x 20.7'' x 2.7'' 35.8'' x 5.71'' x 2.7'' 35.8'' x 11.34'' x 2.7'' 35.8'' x 16.54'' x 2.7'' 35.8'' x 20.7'' x 2.7'' 47.2" x 5.71" x 2.7" 47.2" x 11.34" x 2.7" 47.2" x 16.54" x 2.7" 47.2" x 20.7" x 2.
PAGE 3
6/30/2013 DO NOT USE WITH DIMMERS. THIS DEVICE IS NOT INTENDED FOR USE WITH EMERGENCY LIGHTING (BATTERY TYPE) SYSTEMS FOR FLUORESCENT LIGHTING PRODUCTS. 1. Electrical Characteristics (Typical value): Length 2ft (54105111, 54105131, 54105141) Voltage AC (V) 120-277 Current AC (mA) 150 Power (W) 9 PFC >0.9 Rated Frequency (Hz) 50/60 Length 3ft (54130111, 54130131, 54130141) Voltage AC (V) 120-277 Current AC (mA) 300 Power (W) 14 PFC >0.
PAGE 4
6/30/2013 Note: LED Tube Lamp requires single end power only; wiring to one side of the fixture is sufficient. Ensure lamp end labeled “POWER THIS END” is installed to the live circuit. CAUTION: LAMP HOLDERS MUST BE NON-SHUNTED. POWER FLOWS THROUGH LED TUBE LAMP 1. Turn off the power to the light fixture at the breaker panel before installation. 2. If retrofitting an enclosed fixture open the diffuser from the light fixture. 3. Remove existing fluorescent lamps.
PAGE 5
. 6. 6/30/2013 Cut the wires shown as the diagram below. Optional: Remove ballast and starter and dispose or recycle in accordance with local requirements. Inductive ballast type Electronic ballast type Ballast with 2 lamps Ballast with 3 lamps Make the new wire connection for new branch circuit wiring required and shown as in diagram below. The labeled end of LED Tube Lamp is the live, input powered end. The opposite end is electrically isolated and serves as means of mechanical support only. 7.
PAGE 6
/30/2013 Imported by ETi Solid State Lighting, Inc. 26650 Renaissance PKWY, STE6 Cleveland, OH 44128 Made in China LIMITED WARRANTY: This product is warranted for a period of 5 years from the date or original purchase against defects in materials and workmanship. If this product should fail to operate due to defects in material or workmanship, simply call 1-216-468-0232 within 60 months of purchase. This product will be repaired or replaced, at ETi’s option.