Installation Guide

Model # 56572113
56572114
56572115
USE AND CARE GUIDE
11” LowPro Decorative Flushmount With Warm 2000K Night Light
NOTE: Keep your receipt and these instructions for proof of purchase.
WARNING: Shut off the power at the circuit breaker or fuse panel before removing the old fixture,
ballast, or fluorescent tubes.
If you are unfamiliar with electrical installations, we recommend you contact a qualified electrician to do
the installation.
INSTALLATION
Shut off power at the electrical panel before beginning the installation.
Remove existing fixture and set aside to recycle in accordance with local requirements.
Choose your favorite correlated color temperature (CCT) before installing the fixture housing to the
electrical outlet box.
NOTICE: The factory setting for the correlated color temperature (CCT) is 3000K, which is the warmest
white light. Night light mode provides reduced light output at 2000K color temperature for very soft
illumination at night.
WARNING: Carefully read and understand the information given in this manual before beginning the assembly and installation. Failure to do so could lead to electric shock, fire, or
other injuries which could be hazardous or even fatal. • Risk of electrical shock. Ensure the electricity to the wires you are working on is shut off. Either remove the fuse or turn off
the circuit breaker. • This product must be installed in accordance with the applicable installation codes by a person familiar with the construction and operation of the product and
the hazards involved. • Risk of electrical shock. To reduce the possibility of serious injury, always take the proper precautions and unplug the fixture before moving or cleaning.
NOTICE: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired operation. These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna, increase the separation between the equipment and the receiver, connect the equipment into an outlet on a circuit different from that to which
the receiver is connected, and consult the dealer or an experienced radio/TV.
• Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. • Suitable for damp locations. •
Minimum 90° C supply conductors • Suitable for operation in ambient temperatures not exceeding 113°F/45°C.
See website for Warranty, Troubleshooting or Care and Cleaning details at www.ETiSSL.com.
Questions, problems, missing parts? Call ETiSSL Customer Service 8 a.m. - 5 p.m., CST, Monday - Friday
1-855-ETI-SSLI (1-855-384-7754) www.ETiSSL.com
Wrap ground wire from electrical box around the ground
screw or cover with a wire connector.
Feed black and white wires from the electrical box through
the mounting bracket.
4
6
PACKAGE CONTENTS
Part Description Quantity
A Fixture 1
B Mounting Bracket 1
C Electrical Box Screw 2
D Wire Connector 2
A
1
2
3
MOUNTING BRACKET INSTALLATION
Use screws to attach the mounting
bracket to the electrical box.
7
Make the electrical connections:
• Black wire to black wire.
• White wire to white wire.
• Use wire connectors to cover the wire connections
and cover with electrical tape.
Tuck wires inside the electrical box.
8
Part # FMNL-11IN-900LM-8-CP3-SV-TD-WT
FMNL-11IN-900LM-8-CP3-SV-TD-BN
FMNL-11IN-900LM-8-CP3-SV-TD-ORB
Certification # 56572113
56572114
56572115
5
9
Rotate the fixture so the driver box aligns with the mounting bracket in the electrical box, and snap the fixture into the
mounting bracket. Make sure the fixture is secure.
Restore power to the electrical box. Turn the light switch off and back on again to activate the night light.
NOTE: The main light will not provide light output when the night light is illuminated.
10
B C D
Electrical Box
Electrical Box
D
A
B
C
B
B
Electrical Box
Driver Box
A
La versión española está en el
sitio web www.ETiSSL.com.