Installation Guide

ManualsBrandsETi ManualsCommercial Lighting2 ft. x 2 ft. 64-Watt Equivalent Integrated LED White Troffer Flat Panel Color Changing Dimmable 3300 Lumens (8-Pack)

Model # 64204301

64204401

64205401

64204302

64205402

Part # FPCP-2x2-3300LM-8-CP3-MV-LVD

FPCP-2x2-4400LM-8-CP3-MV-LVD

FPCP-2x4-4950LM-8-CP3-MV-LVD

FPCP-2x4-4950LM-8-CP3-MV-LVD-1PK

Certiﬁcation # 64204301

64204401

64205401

64204302

64205402

USE AND CARE GUIDE

LED FLAT PANEL

NOTE: Keep your receipt and these instructions for proof of purchase.

WARNING: Shut off the power at the circuit breaker or fuse panel before

removing the old ﬁxture, ballast, or ﬂuorescent tubes.

If you are unfamiliar with electrical installations, we recommend you contact

a qualiﬁed electrician to do the installation.

NOTE: Two people are recommended for installation of this light

ﬁxture.

NOTE: W = 5000K, NW = 4000K, and SW =3500K.

INSTALLATION

NOTICE: Select a suitable location that can support the weight of the

ﬁxture. Determine the method of mounting before beginning installation.

CAUTION: The weight of the LED ﬂat panel (A) is not designed to be

supported by the ceiling grid. The LED ﬂat panel should be connected

back to the structure. Failure to do so can cause serious injury.

Shut off power at the electrical panel before beginning the installation.

Remove existing ﬁxture and set aside to recycle in accordance with

local requirements.

PACKAGE CONTENTS

Part Description Quantity

A Fixture 1

Remove the driver cover.

Make the electrical connections:

Connect black (L) wire with black wire in the driver.

Connect white (N) wire with white wire in the driver.

If a 0-10v dimming circuit is available, connect ﬁxture purple

wire to driver DIM+ and gray ﬁxture wire to Driver DIM-.

Remove knock out hole(s) and connect driver to conduit

(based on local electrical code).

Tuck wires inside the driver box and reattach the driver

cover.

MAKING ELECTRICAL CONNECTIONS

Part Description Quantity Part #

AA Aircraft Cable for Suspension Mounting 2 95457326101

BB Surface Mounting Kit for 2’ x 2’ Flat Panel 1 FPE-SMK-22

CC Surface Mounting Kit for 2’ x 4’ Flat Panel 1 FPE-SMK-24

HARDWARE AVAILABLE TO PURCHASE

Hardware kits for surface mounting and suspension mounting are sold as separate accessories.

Please contact ETiSSL Customer Service 1-855-384-7754 for additional information.

x 2

Surface Mounting Kits - BB and CC

x 2 x 12

x 2

x 4

If installing a battery back-up, then make the

electrical connections.

Use screws to secure the emergency

battery backup to the ﬁxture

Connect the conduit to the driver

(based on local electrical code).

EMERGENCY BATTERY BACKUP

Green

Unswitched

Hot

Black

Wall

Switch

White/

Blue

White

Blue

White/

Red

Orange

AC LED

DRIVER

Common

Output+

Output-

White

Red

Black

White/

Black

White/

Black

ITS

LED DRIVER

EMERGENCY

Converter

Connnector

LED

Load-

LED

Load+

Yellow

Black

White

BBU

LED Driver

Black

White

Purple 0-10v

Dim+

Gray 0-10v

Dim-

Switch

Panel

Summary of content (6 pages)

PAGE 1
Certification # 64204301 Model # 64204301 Part # FPCP-2x2-3300LM-8-CP3-MV-LVD 64204401 FPCP-2x2-4400LM-8-CP3-MV-LVD 64204401 64205401 FPCP-2x4-4950LM-8-CP3-MV-LVD 64205401 64204302 FPCP-2x4-4950LM-8-CP3-MV-LVD-1PK 64204302 64205402 FPCP-2x4-4950LM-8-CP3-MV-LVD-1PK 64205402 Use and Care Guide LED FLAT PANEL NOTE: Keep your receipt and these instructions for proof of purchase. WARNING: Shut off the power at the circuit breaker or fuse panel before removing the old fixture, ballast, or fluorescent tubes.
PAGE 2
Suspension Mounting GRID CEILING INSTALLATION Mounting Clip Quick Cable Lock AA AA A Mounting Clips 10b 10b CAUTION: Clip is used for positioning (NOT for mounting) Bend each of the mounting clips on the back of the fixture upward and then twist the top 90°. Place the fixture into the ceiling grid, hook the mounting clips over the grid ceiling supports and make sure it is secure. 11b Depending on mounting location, install 4 toggle bolts into drywall or 4 hook screws into wood.
PAGE 3
N° de certification 64204301 Modèle n° 64204301 N° de pièce FPCP-2x2-3300LM-8-CP3-MV-LVD 64204401 FPCP-2x2-4400LM-8-CP3-MV-LVD 64204401 64205401 FPCP-2x4-4950LM-8-CP3-MV-LVD 64205401 64204302 FPCP-2x4-4950LM-8-CP3-MV-LVD-1PK 64204302 64205402 FPCP-2x4-4950LM-8-CP3-MV-LVD-1PK 64205402 GUIDE D’UTILISATION ET D’ENTRETIEN LUMINAIRE PLAT À DEL REMARQUE : Gardez votre facture ainsi que ces instructions comme preuves d’achat.
PAGE 4
Montage en suspension MONTAGE DANS UN FAUX PLAFOND Pince de montage Loquet de câble AA AA A Pince de montage 10b 10b MISE EN GARDE : La pince ne sert qu’au positionnement (PAS au montage). Pliez vers le haut chaque pince de montage au dos du luminaire, puis tournez la partie supérieure sur 90°. Placez le luminaire dans le grillage, accrochez les pinces au cadre de sustainement et assurez-vous que tout est bien retenu.
PAGE 5
Certification # 64204301 Model # 64204301 Part # FPCP-2x2-3300LM-8-CP3-MV-LVD 64204401 FPCP-2x2-4400LM-8-CP3-MV-LVD 64204401 64205401 FPCP-2x4-4950LM-8-CP3-MV-LVD 64205401 64204302 FPCP-2x4-4950LM-8-CP3-MV-LVD-1PK 64204302 64205402 FPCP-2x4-4950LM-8-CP3-MV-LVD-1PK 64205402 MANUAL DE USO Y CUIDADO LUMINARIA PLANA LED NOTA: Guarde el recibo de compra y estas instrucciones como prueba de compra.
PAGE 6
Montaje en suspensión Instalación en techo modular Clip de montaje Cierre rápido de cable AA AA A Clip de montaje 10b 10b PRECAUCIÓN: El clip se usa para posicionar (NO para montar). Doble hacia arriba cada clip de montaje en la parte posterior de la luminaria, luego gire la sección superior 90 °. Coloque el dispositivo en la rejilla del techo, enganche los clips de montaje sobre los soportes del techo de la rejilla y asegúrese de que esté seguro.