ENFI 8517 ZT Bedienungsanleitung Geschirrspüler instruction book dishwasher
Contents Safety instructions 21 Disposal 21 Economical and ecological dishwashing 21 Description of the appliance 22 The control panel 22 Prior to using for the first time Setting the water softener Filling with salt Rinse aid 23 23 24 25 In daily use Loading cutlery and dishes The lower basket The cutlery basket The upper basket Adjusting the height of the upper basket Use of detergent 26 26 27 27 27 27 28 Washing programmes 29 Starting a washing programme 30 Maintenance and cleaning Clea
Safety instructions It is most important that this instruction book should be retained with the appliance for future reference. Should the appliance be sold or transferred to another owner, or should you move house and leave the appliance, always ensure that the book is left with the appliance in order that the new owner can get to know the functioning of the appliance and the relevant safety information. ● Isolate the appliance from the power supply and turn off the water supply after use.
Description of the appliance 1. Upper basket stop 2. Water hardness switch 3. Salt container 4. Detergent dispenser (type A / type B) 5. Control panel 6. Rating plate 7. Rinse aid dispenser (type A / type B) 8. Filters 9. Lower spray arm 10. Upper spray arm 11.
3. Press the function push button 3, the indicator lights of function push buttons 1 and 2 turn off while the indicator light of the push button 3 goes on flashing, the digital display indicates the current setting.
Setting electronically Filling with salt (The dishwasher must be switched off) Special salt can be added in one of two ways: The dishwasher is factory set at level 5. If it’s necessary to set a new level, proceed as follows. ● If you are using dishwasher detergent that already contains salt, the detergent including the salt is placed in the detergent compartment.
Rinse aid Filling with rinse aid Rinse aid is automatically added during the last rinse, ensuring thorough rinsing, and spot and streak free drying. The dispenser, which is positioned inside the door, holds about 110 ml of rinse aid, which is sufficient for 16 - 40 dishwashing programmes, depending upon the dosage setting. (Rinse aid dispenser type B) 1. Open the container by turning the lid (A) anticlockwise. 2. Add the rinse aid until the container is completely full.
3. Press the function push button 2, the indicator lights of function push buttons 1 and 3 turn off while the indicator light of the push button 2 goes on flashing, the digital display indicates the current setting. Deactivation/activation of the inflow of rinse aid (The dishwasher must be switched off) When the inflow of rinse aid has been deactivated, also the rinse aid indicator light on the control panel is automatically deactivated.
Open the door and slide out the baskets to load the dishes. The upper basket The upper basket is designed for plates (dessert plates, saucers, dinner plates of up to 25 cm in diameter), salad bowls, cups and glasses. Arrange items on and underneath the cup racks so that water can reach all surfaces. For taller items, the cup racks can be folded upwards. Glasses with long stems can be placed upside down in the cup racks. Light items (plastic bowls etc.
Use of detergent Use of "3 in 1" combi detergent tablets Only use detergents specifically designed for use in dishwashers. General advice These products are tablets with combined detergent/rinse-aid and salt functions. Using no more then the correct amount of detergent contributes to reducing pollution. 1. Before using these products you should first check that the water hardness in your supply is compatible with the use of these products as per the detergent manufacturers (on the product packaging).
Washing programmes Programme Degree of soil and type of load Cycle description (3) Consumption values Programme duration (in minutes) Energy consumption (in kWh) Water consumption (in litres) 12 0,1 4 1. Rinse and Hold Any. Partial load (to be completed later in the day). This programme does not require the use of detergent. 1 cold rinse (to avoid food scraps from sticking together) 2. Intensive 70°C Heavy soil.
Starting a washing programme In this fully integrated appliance the controls are located on the top of the door. When selecting a programme, the door needs to be open. To cancel a washing programme in progress Open the dishwasher door. Press simultaneously the function push buttons 2 and 3 for about 2 seconds, the indicator lights of the programme selection push buttons start flashing for about 2 seconds.
7. End of the washing programme The dishwasher will automatically stop and 3 intermittent audible signals of about 15 seconds each, alternated one from another with a pause of 3 minutes, inform you of the end of the washing programme. Hot steam may escape from the appliance when opening the door immediately after the end of the programme, therefore, open the door carefully. The end of programme indicator light is illuminated. Switch off the dishwasher by pressing the On/Off push button.
Maintenance and cleaning Clean the external surfaces of the machine and control panel with a damp soft cloth. If necessary use only neutral detergents. Never use abrasive products, scouring pads or solvent (acetone, trichloroethylene etc....). To ensure a correct working of the dishwasher, NEVER try to remove the upper spray arm. Ensure that the seals around the door, the detergent and rinse aid dispensers are cleaned regularly with a damp cloth.
What to do, when... Certain problems are due to the lack of simple maintenance or oversights, which can be solved with the help of the instructions given here, without calling out an engineer. ...a flashing fault code appears The intervention of an alarm is indicated by a combination of flashing indicator lights, audible signals and a visible fault code in the digital display, as indicated in the following chart. Carry out the following suggested corrective actions.
...the wash results are not satisfactory The dishes are not clean ● ● ● ● ● ● ● ● The wrong washing programme has been selected. The dishes were arranged in such a way as to stop water reaching all parts of the surface. The baskets must not be overloaded. The spray arms do not rotate freely due to wrong arrangement of the load. The filters in the base of the washing compartment are dirty or incorrectly positioned. Too little or no detergent has been used.
Installation instructions Any electrical and/or plumbing work required to install this appliance should be carried out by a qualified electrician and/or plumber or competent person. Water supply connections This dishwasher may be fed with either hot (max. 50°) or cold water. Nevertheless we advise you a cold water supply. A hot water supply is not always efficient with very soiled crockery as it shortens the washing programmes a lot. Remove all packaging before positioning the machine.
Water outlet hose connection Electrical connection The end of the drain hose can be connected in the following ways: Information concerning the electrical connection is given on the rating plate on the edge of the dishwasher’s door on the right. 1. To the sink outlet spigot, securing it to the underside of the work surface. This will prevent waste water from the sink running into the machine. Before plugging the appliance into the wall socket, make sure that: 1.
Hints for test centres Testing in accordance with EN 60704 must be carried out with appliance fully loaded and using the test programme (see "Washing programmes" chart). Test in accordance with EN 50242 must be carried out when the salt dispenser and rinse aid container have been filled with salt and rinse aid respectively and using the test programme (see "Washing programmes" chart).
152972 82/3 Änderungen vorbehalten Subject to change without notice 05/05
