Owner Manual

ManualsBrandsEtta Avenue Teen ManualsArmoires & WardrobesAbril Armoire

Table Of Contents

ASSEMBLY RATING

The Assembly Rating is a 5-point system that shows the degree of

effort needed in

assembling a specific product (with 1 being

easy and 5 being difficult). For most

products,two persons are recommended.

EASY

DIFFICULT

Page 1 of 17

Hammer

Phillips Screwdriver

Tools Required for Assembly:

2 PERSONS RECOMMENDED

(Not Included)

Summary of content (17 pages)

PAGE 1
ASSEMBLY RATING Tools Required for Assembly: The Assembly Rating is a 5-point system that shows the degree of effort needed in Phillips Screwdriver assembling a specific product (with 1 being easy and 5 being difficult). For most products,two persons are recommended.
PAGE 2
Thank you for your purchase! We hope you wiIl enjoy your new product for many years to come. Our commitment to providing quality products does not simply end when a purchase is made. We stand behind our products and will provide any support needed in order for you to fully enjoy your purchase. Your satisfaction is the greatest recognition we could have.
PAGE 3
FOR YOUR FURNITURE TO LAST,CORRECT ASSEMBLY AND PROPER MAINTENANCE ARE NECESSARY PLEASE FOLLOW THE INFORMATION PROVIDED BELOW TO FULLY ENJOY YOUR FURNITURE. BASIC ASSEMBLY TECHNIQUES It is highly recommended that the assembly should be done near the area of its intended location. Make sure you have enough space to move around during the assembly. Position each part correctly and insert screws or bolts into their respective holes by hand tighten or using the proper hand tool.
PAGE 4
Unless you are particularly adept at assembling flat-pack/knock-down furniture, we understand building ready-to-assemble furniture can be a frustrating experience for some. To help avoid confusion and to make the assembly process quicker and smoother, we have provided some helpful tips. Before you begin the assembly, please read the following : 1. 2. 3. 4. 5. 6. 7.
PAGE 5
Note:Every cam lock bolt must have a cam lock connector in order to fasten the parts together. (1) Align the cam connector with its side opening (or arrow) pointing to the small driIIed hole. Secure the threded end of the cam bolt by using a screwdriver. Tun right (clokwise) to tighten. (3) (2) Insert the cam lock bolt into the pre-drllled hole above the cam connector. Two parts should fit snugly against each other.
PAGE 6
Before you begin,please read"Assembly and Care Advice","Pre-Assembly Introduction"and "Cam Lock Fastener Assembly Instructions".
PAGE 7
Due to the size and/or weight of this product,it is highly recommended that the assembly should be done near the area of its intended location.Make sure you have enough space to move around during the assembly.
PAGE 8
Ix1 Jx4 Fx2 Dx4 Page 8 of 17
PAGE 9
Bx2 Ax2 7 4 7 4 Bx2 Ax2 Page 9 of 17
PAGE 10
Ex6 3 4 3 Page 10 of 17
PAGE 11
5 Bx6 Ex2 3 5 Page 11 of 17
PAGE 12
Ex4 Zx4 4 Gx4 5 2 Bx4 Wx4 1 4 5 2 Page 12 of 17
PAGE 13
U 4 Zx4 Ex4 5 2 Vx35 5 2 Page 13 of 17
PAGE 14
1 1 Page 14 of 17
PAGE 15
Yx16 1 Xx4 Ix2 4 Jx4 1 4 Make sure the unit is rested on a flat surface and does not feel loose or wobbly If it does,double check that the bolts/screws secured and properly tightened Page 13are of 15 ASSEMBLY IS COMPLETED Page 15 of 17
PAGE 16
Page 16 of 17
PAGE 17
Anti-Tipping strap lnstruction Hardware List (Included): STEP 1 STEP 2 STEP 3 STEP 4 Page 17 of 17