User Manual

ManualsBrandsEtymotic Research ManualsAudio EquipmentetyBLU 2 Bluetooth Headset

ETYMOTIC RESEARCH INC.

61 Martin Lane • Elk Grove Village, IL 60007

www.

etymotic.com • 1-888-389-6684

Bluetooth SIG,Inc.The etyBLU headset is covered by one of more of the following U.S.patents: #5,878,147

#6,075,869 #6,134,344 #6,151,399 #6,285,771 #6,567,526 and other patents pending. ER089401 01/08

LED Chart

Power ON Blue LED is solid for

one second while powering on

Power OFF Yellow LED is solid for

one second then powers off

Pairing Blue LED blinks twice every

3 seconds

Active call Blue LED blinks once per second

No active call Blue LED blinks every 4 seconds

Charging Solid yellow LED

Low battery Blinking yellow LED

Charge complete Yellow LED off

User Manual

Dual Mode

Noise-Isolating

Headset

Summary of content (10 pages)

PAGE 1
LED Chart Power ON Blue LED is solid for one second while powering on Power OFF Yellow LED is solid for one second then powers off Pairing Blue LED blinks twice every 3 seconds Active call Blue LED blinks once per second No active call Blue LED blinks every 4 seconds Charging Solid yellow LED Low battery Blinking yellow LED Charge complete Yellow LED off ETYMOTIC RESEARCH INC. 61 Martin Lane • Elk Grove Village, IL 60007 www.etymotic.com • 1-888-389-6684 ©2008.
PAGE 2
Table of Contents Introduction..............................................................................4 Included....................................................................................5 Bluetooth Profiles ....................................................................5 Identification ............................................................................6 Dual Modes–Two Ways to Use..................................................7 Pairing ........................................
PAGE 3
Introduction The Etymotic etyBlu dual mode, noise-isolating headset contains two microphones. One microphone is located internally at the end of the earpiece; the other, BLUmaxx™, a highly directional, noise-rejecting microphone quickly connects to the earpiece. The combination of an in-ear noise-isolating earphone and a directional microphone placed close to the mouth provides exceptional sound quality and clear communication at both ends of the conversation.
PAGE 4
Identification Dual Modes—Two Ways to Use etyBLU with BLUmaxx connected and earloop No boom, no earloop B A E C C D D Internal Mic Mode The earpiece is designed to be self-supporting in the ear canal, so the earloop is optional. Push the earloop through the earloop holder and adjust for a secure fit. F G Internal Microphone H A. Eartip B. Speaker C. Multi-Function Button (MFB) D. Volume Up/Down E. Optional Earloop F. Earloop Holder G. Jack for BLUmaxxMic and Charging Cable H.
PAGE 5
Pairing Pairing varies by device The etyBLU headset is discoverable for five minutes after Power On. • • • • Turn the phone OFF and then back ON. Turn on the mobile phone’s Bluetooth function. Press and hold the Multi-Function Button (MFB) for 5 seconds. The blue LED will flash rapidly when ready for pairing.The etyBLU stays in pairing mode for 5 minutes. Activate the search for BT and/or audio devices on the phone When the etyBLU is found, the phone will display “etyBLU.
PAGE 6
Insertion Important: Sound quality and noise isolation depend on a good eartip seal. BLUmaxx Connect/Disconnect NOTE:The BLUmaxx Mic can quickly connect or disconnect without disconnecting a call. Hold here to connect/disconnect • Carefully insert the earpiece while pulling up and out on the back of the ear. For a video on proper earphone insertion go to • Twist the earpiece while inserting www.etymotic.com until outside noise is blocked out. • Position the earpiece for best fit and comfort.
PAGE 7
Multi-Function Button (MFB) Multi-Function Button (MFB) PRESS the MFB for 4 seconds to MFB Power On. Blue LED is solid for one second while powering ON. Blue LED blinks when the headset is ON. The following features depend on phone support: Redial PRESS and HOLD the MFB (long press) for one second. Power OFF PRESS the MFB for 4 seconds to Power Off. Yellow LED is solid for one second then powers OFF. Voice Call PRESS the MFB quickly (short press) to make a voice call.
PAGE 8
Earpiece Filter Caution The earpiece in the etyBLU headset has a special filter that smoothes the frequency response and prevents earwax from entering the earphone.The filter is located at the end of the earphone and is visible when the eartip is removed. Change the filter if loudness decreases or the sound quality declines. Note: Filters are not reusable. Filter Removal 1. Remove eartip. 2. Insert tool into the filter.
PAGE 9
FCC & Other Information This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1.This device may not cause harmful interference, and 2.This device must accept any interference received, including interference that may cause undesired operation.These limits are designed to provide reasonable protection against harmful interference in a residential installation.
PAGE 10
Proper Care • Do not expose the headset to extreme temperatures. • Avoid dropping and strong impact. • Leave an eartip on the headset for shock protection. Cleaning/replacement of eartip • Clean or replace a flanged eartip prior to use by others. • Replace a foam eartip prior to use by others. • Clean a flanged eartip by simply wiping it off with a soft cloth. If water and mild soap are used, remove the eartip, clean and dry it before replacing it on the headset. • Replace disposable foam eartips regularly.