Bedienungsanleitung Eudora ProfiVap plus 205 Druckdampf-Bügelstation
EUDORA ProfiVap plus 205 Beschreibung 1) Dampfdruckmanometer 2) Kontrollleuchte Bügeleisentemperatur 3) Temperaturregler 4) Arretierung für Dauerdampf aus der Bügelsohle 5) Dampfstoßtaste 6) Heizkesselverschluss 7) Abstellfläche für Bügeleisen 8) Halterung Versorgungskabel 9) Dampfmengenregulierung 10) Ein/Aus-Schalter für Druckdampfstation 11) Anzeige "Tank leer" 12) Anzeige "Dampf bereit" 13) Ein/Aus-Schalter für Bügeleisen 2
Vor Inbetriebnahme der Bügelstation lesen Sie bitte diese Bedienungsanleitung sorgfältig durch, um optimale Ergebnisse beim Einsatz zu erzielen und ein Höchstmaß an Sicherheit zu gewährleisten. SICHERHEITSHINWEISE · Achten Sie darauf, dass die Steckdose mit Schutzleiteranschluss versehen ist, und die Netzspannung sowie die Absicherung mit dem Typenschild am Gerät übereinstimmen. · Stecker von einer Fachperson auswechseln, sollte er nicht mit Ihrer Steckdose übereinstimmen.
· Wenn das Gerät endgültig entsorgt werden soll, Netzstecker ziehen und das · · · · · · · · · · · · · · · · · Netzkabel durchschneiden, so dass das Gerät nicht mehr benutzt werden kann. Das Netzkabel darf nicht vom Benutzer selbst ausgetauscht werden, da hierfür spezielle Werkzeuge erforderlich sind. Wenden Sie sich im Falle eines beschädigten Netzkabels an eine vom Hersteller autorisierte Kundendienststelle. Den Dampfstrahl niemals auf Menschen oder Tiere richten. Verbrennungsgefahr.
BEFÜLLEN DES HEIZKESSELS · Obwohl die Bügelstation mit normalen Leitungswasser betrieben werden kann, führt härteres Wasser im Laufe der Zeit zu Störungen im Dampfsystem. Um dies zu vermeiden empfehlen wir Ihnen folgendes Vorgehen: Messen Sie mit dem beiliegenden Teststäbchen die Wasserhärte Ihres Leitungswassers. Stäbchen kurz (1 Sekunde) ins Wasser eintauchen, leicht abschütteln und nach 1 Minute ablesen. Verändert sich nur die 1. (unterste) Zone von grün auf rot, eignet sich das normale Leitungswasser.
Abb.1 Für optimale Bügelergebnisse die Dampfstoßtaste (5) mit kurzen Unterbrechungen betätigen, damit das Bügeleisen ausdampfen und das Bügelgut trocknen kann. · Die gewünschte Dampfmenge lässt sich mit der Dampfmengenregulierung (9) wählen. Durch Drehen im Uhrzeigersinn erhöht sich die Dampfmenge. (Abb. 1). · Nach dem Gebrauch das Bügeleisen abkühlen lassen und den Heizkessel leeren. · Leuchtet die Anzeige "Tank leer" (11) auf, ist der Heizkessel leer und Wasser muss nachgefüllt werden.
! Bevor Sie den Heizkesselverschluss (6) abschrauben, vergewissern Sie sich, dass der Heizkessel nicht mehr unter Druck steht. ! Vergewissern Sie sich, dass das Gerät nicht an das Stromnetz angeschlossen ist. ! Schrauben Sie den Heizkesselverschluss (6) ab. ! Wenden Sie das Gerät und leeren Sie den Heizkesselinhalt in einen Behälter aus. ! Den Heizkessel mit ca. 0,5 Liter Leitungswasser befüllen. ! Station schwenken und ausleeren, damit die Kalkrückstände und Verunreinigungen im Wasser ausgespült werden.
TEMPERATURÜBERSICHT TEMPERATURREGLER AM BÜGELEISEN TEMPERATUR MATERIAL Acetat / Acryl / Samt / Nylon / Seide / Viskose Polyester / Rayon / Wolle Baumwolle / Denim / Leinen Temperaturbereich nach IEC 60311 70°C bis 120°C 100°C bis 160°C 140°C bis 210°C 8
FEHLERSUCHE UND -BEHEBUNG Manchmal lassen sich Fehler durch die Überprüfung einiger einfacher Punkte beheben. Wichtig! Um das perfekte Funktionieren professioneller Bügelsysteme zu gewährleisten, muss der Heizkessel regelmäßig entkalkt werden.
Garantiebedingungen gültig ab 1.4.2004 Die EUDORA SOBA - Garantie wird für alle EUDORA SOBA Geräte geleistet, welche das Originalleistungs-schild mit Gerätenummer aufweisen. Ohne die gesetzliche Gewährleistung einzuschränken, geben wir - abgesehen von den unter 2. Angeführten Fällen - 2 Jahre Garantie ab Kaufdatum (Nachweis ist der Kaufbeleg). 1.