FCC ID:2AOKB-T8210 IC:23451-T8210 Quick Start Guide Anker Innovations Limited. All rights reserved. eufy Security and eufy Security Logo are trademarks of Anker Innovations Limited, registered in the United States and other countries. All other trademarks are the property of their respective owners.
TABLE OF CONTENTS What’s Included 02 10 Mounting The Bracket Product Overview 03 13 Mounting The Doorbell How The System Works 04 14 Detaching The Doorbell Verifying Your Homebase 05 15 Charging The Doorbell Adding The Doorbell To Your Existing System 05 16 Powering The Doorbell With Existing Doorbell Wires Determining The Power Option 06 24 Notice Finding A Mounting Spot 08 27 Customer Service English 01
WHAT’S INCLUDED PRODUCT OVERVIEW For Video Doorbell Installation Video Doorbell (Battery Powered) Front view: 1 2 3 1. Motion Sensor 2. Microphone 4 3. Camera Lens 4. Ambient Light Sensor Video Doorbell Mounting Bracket Model: T8210 Screw Hole Positioning Card 5 15° Mounting Wedge (Optional) 5. LED Ring 6. Doorbell Button 6 7. Speaker FCC ID: 2AOKB-T8210 IC: 23451-T8210 7 Rear View: 1 2 3 1.
HOW THE SYSTEM WORKS STEP 1 VERIFYING YOUR HOMEBASE How the System Works Verify Your HomeBase The video doorbell system includes 2 parts. One is the video doorbell at your door. The other is the HomeBase in your house. The battery video doorbell cannot work without a HomeBase or eufyCam series system. Make sure you have an existing eufyCam series system installed and working. The video doorbell detects motion at your porch and allows you to answer the door anytime and anywhere.
STEP 3 DETERMINING THE POWER OPTION Option 1 - Battery Powered 1. If you don’t have existing doorbell wiring at the front door, use the built-in battery. You are free to determine the doorbell position and the mounting is easy and quick. 2. When the doorbell battery level is low, you need to detach and charge it. 3. If you choose this option, please jump to STEP 4 FINDING A MOUNTING SPOT. Option 2 - Doorbell Wire Powered 1.
STEP 4 FINDING A MOUNTING SPOT Place the Screw Hole Positioning Card against the wall to mark the position. Find a Mounting Spot Take the video doorbell to your front door and check the live view on the App at the same time. Find a location where you can get the desired field of view. Consider the below factors: 1. Check if you can reuse the existing holes and anchors on the wall or door frame. 2. If the doorbell is close to a wall, make sure the wall doesn’t occupy 25% of the field of view.
STEP 5 MOUNTING THE BRACKET Mount the Doorbell on Surfaces Made Out of Hard Materials 1. If you’re mounting the doorbell on a surface made out of hard materials, like brick, concrete, stucco, drill 2 holes through the Screw Hole Positioning Card with a 15/64”(6mm) drill bit. Mount the Doorbell on a Wooden Surface If you’re mounting the doorbell on a wooden surface, you don’t need to pre-drill pilot holes.
STEP 6 MOUNTING THE DOORBELL Mount the Doorbell Align the doorbell on top and then snap it on the bottom. Press it down until it clicks into place. Wall Mounting Bracket Without 15° Mounting Wedge 2 Wall Mounting Wedge Mounting Bracket With 15° Mounting Wedge 2 You’re all set! If you want to detach the doorbell or recharge it, please refer to the following sections.
APPENDIX 1 DETACHING THE DOORBELL APPENDIX 2 RECHARGING THE DOORBELL Detach the Doorbell Recharge the Doorbell What is required: Doorbell Detaching Pin Doorbell Detaching Pin LED indication Charging time 14 English Charging: Steady blue Fully charged: Off 6 hours English 15
APPENDIX 3 POWERING THE DOORBELL WITH EXISTING DOORBELL WIRES What is required: Philips-Head Screwdriver 3.1 Verify whether the doorbell wires are working 1. Ring the existing doorbell to check if it is working. 2. Shut off power at the breaker. Turn the lights on / off in your home to make sure the electricity in your house is properly shut off. Phillips-Head Screwdriver (User provides it.) OFF OFF Always be careful when handling wires.
3.4 Mount the Bracket 15° 1.76m(5’9”) 1.2m (48") 1m (40") 0.3m (12") If you’re mounting the doorbell on a wooden surface, you don’t need to pre-drill pilot holes. Use the provided screws to secure the Mounting Bracket on the wall. The Screw Hole Positioning Card indicates the position of the screw holes. What is required: Power Drill, Mounting Bracket, 15° Mounting Wedge (Optional), Screw Pack Door Video Doorbell Without 15° Mounting wedge Door Video Doorbell With 15° Mounting wedge 2.
If you’re mounting the doorbell on a surface made out of hard materials, like brick, concrete, stucco: ① Drill 2 holes through the Screw Hole Positioning Card with 15/64”(6mm) drill bit. ② Insert the provided anchors, and then use the provided screws to secure the Mounting Bracket on the wall. What is required: Power Drill, 15/64”(6mm) Drill Bit, Mounting Bracket, 15° Mounting Wedge (Optional), Screw Pack Power Drill with 1/4" (6.35mm) Drill Bit (User provides it.
3.5 Connect the Doorbell Wires to the Doorbell 3.6 Mount the Doorbell on the Bracket Connect the wires to the terminals at the back of the doorbell, then tighten the terminal screws. Wire can connect to any terminal. Align the doorbell on top and then snap it on the bottom. What is required: Wires and Wire Nuts (Optional) / Video Doorbell / Philips-head Screwdriver Extension Wires and Wire Nuts (Optional) Video Doorbell 2K (Wired) Phillips-Head Screwdriver (User provides it.) 3.
NOTICE This product complies with the radio interference requirements of the European Community. FCC Statement Declaration of Conformity This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
IC Statement This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device." Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
