Owner’s Manual RoboVac 15C (T2120) T2120 51005001250 V02
Table of Contents 02 Important Safety Instructions 07 About Your RoboVac What's in the Box RoboVac Anatomy LED Indication 11 Using Your RoboVac Important Tips Before Use Preparation Charge Your RoboVac Use Your RoboVac with the EufyHome App Start / Stop Cleaning Select a Cleaning Mode Use Your RoboVac with Amazon Alexa / the Google Assistant 22 Cleaning and Maintenance Clean the Dust Collector and Filters Clean the Rolling Brush Clean the Side Brushes Replace the Side Brushes Clean the Sensors and Charg
Important Safety Instructions To reduce the risk of injury or damage, read these safety instructions carefully and keep them at hand when setting up, using, and maintaining this device. WARNING SYMBOLS USED This is the safety alert symbol. This symbol alerts you to potential hazards that could result in property damage and/or serious bodily harm or death.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
de portée. Si l’appareil passe par-dessus un câble et l’entraîne avec lui, cela risque de causer des chutes d’objets. • Si la pièce à nettoyer a un balcon, une barrière physique doit être placée afin d’empêcher l’accès au balcon et d’assurer une utilisation sûre. • Ne pas placer d’objet sur l’appareil. About Your RoboVac What's in the Box • Rester conscient que l'appareil se déplace seul. Faire attention à ne pas marcher sur l’appareil par inadvertance.
RoboVac Anatomy Dust Collector Top & Side Pre-filter Auto cleaning Start/Stop button Wi-Fi status light Bumper High-performance filter Foam filter Infrared sensor Suction Inlet Dust collector Dust collector release button Dust collector Bottom Charging contact pins Drop sensors Swivel wheel Side brushes Suction inlet Battery compartment Brush guard Rolling brush Main power switch (On/Off) Wheels Dust collector Charging Base Status light Charging contact pins 08 Power cord storage compartment
Remote Control (Wi-Fi Status Light) 2 1 Slowly flashing blue Waiting for connection Return RoboVac to Charging Base Rapidly flashing blue Connecting with your wireless router Adjust suction power level in Auto and Quick Cleaning modes Solid blue Connected to your wireless router Start Auto cleaning / Stop cleaning 3 4 Status Control cleaning direction manually Using Your RoboVac Start Auto cleaning 5 6 7 8 Start Edge cleaning Important Tips Before Use Start Spot cleaning Start Quick
f Anti-drop sensors prevent RoboVac from tumbling down stairs and steep drops. They may work less effectively if dirty or used on reflective/very dark-colored floors. Place the Charging Base on a hard, level surface and against a wall. Place physical barriers in front of fireplaces and areas that may cause damage to RoboVac if entered. Preparation Install the side brushes before use. Remove objects within 3 ft/1 m of the left and right side and within 6 ft/2 m of the front of the Charging Base.
Method 1: Attach RoboVac to the Charging Base by aligning its charging pins with the charging pins on the base. • RoboVac is attached to the Charging Base to ensure it has enough power during setup. EufyHome EufyHome Method 2: Press on the remote control to return RoboVac to the Charging Base. 1. Download the EufyHome app from the App Store (iOS devices) or Google Play (Android devices). 2. Open the app and create a user account.
Schedule Cleaning Press on RoboVac or / on the remote control to start cleaning in Auto Mode. With the EufyHome app, you can schedule RoboVac to start cleaning at a particular time. • You can set the time and customize the cleaning schedules from Sunday to Saturday on the EufyHome app. This function is available in the app only. Start / Stop Cleaning • Make sure the main power switch on the bottom of RoboVac is turned on before use. • You can also start or stop cleaning via the EufyHome app. 1.
2. Spot cleaning 4. Quick cleaning RoboVac intensively cleans a specific area in a spiral pattern, useful if there is a concentrated area of dust or debris. In Spot mode, RoboVac will stop cleaning after 2 minutes. RoboVac will automatically stop cleaning after 30 minutes and return to the Charging Base in this mode. If any small room or area needs to be cleaned, it is recommended to select this mode to save time and power. Press Press on the remote control to start cleaning in Spot Mode. 3.
Use Your RoboVac with Amazon Alexa / the Google Assistant Amazon Alexa or the Google Assistant is a smart voice control device that enables you to control RoboVac with your voice. Before you start, make sure that: • RoboVac is attached to the Charging Base to ensure there is enough power. • RoboVac is connected with the EufyHome app. • You have an Alexa-enabled device (i.e. eufy Genie, Amazon Echo, Echo Dot and Amazon Tap, Echo Show, Echo Spot) or a device enabled with the Google Assistant (i.e.
Cleaning and Maintenance Take out the foam filter and high-performance filter. For optimal performance, follow the instructions below to clean and maintain RoboVac regularly. The cleaning/replacement frequency will depend on your usage habits of RoboVac.
Press down to snap the brush guard into place. 1 2 Only use the side brushes when they are completely dry. 3 Replace the Side Brushes The side brushes may become bent or damaged after being used for a period of time. Follow the instructions below to replace them. 4 5 Pull off the old side brushes and snap the new ones into place. Clean the Side Brushes Foreign substances, such as hair, can easily get tangled in the side brushes, and dirt may adhere to them. Be sure to clean them regularly.
Clean the Swivel Wheel Hair or dust particles can easily get entangled in the swivel wheel. Be sure to clean the swivel wheel periodically and as needed. Wheel Axle Troubleshooting Problems Solutions RoboVac cannot be activated. • Make sure the main power switch is in the ON position. • Make sure the battery is fully charged. • Replace the batteries (2 AAA) in the remote control. • Make sure the remote control is within range (16 ft/5 m) of RoboVac.
Problems Solutions The rolling brush does not rotate. • Clean the rolling brush. • Check if the rolling brush and brush guard have been installed properly. RoboVac’s movements or travel path are abnormal. • Clean the sensors carefully with a dry cloth. • Restart RoboVac by turning the power switch off and on. RoboVac cannot connect to a Wi-Fi network. • Make sure your Wi-Fi router supports the 2.4GHz and 802.11b/g/n bands; the 5GHz band is not supported.
- When using a network extender/repeater, make sure the network name (SSID) and password are the same as your primary network. - The firewall and port settings of your Wi-Fi router allow RoboVac to connect with the Eufy servers. Network Security Requirement - WPA and WPA2 using TKIP, PSK, AES/CCMP encryption. - WEP EAP (Enterprise Authentication Protocol) is not supported. Wi-Fi Channels - The FCC requires that all wireless devices in the United States operate on the 1-11 wireless spectrum channels.