Table of Contents 02 Important Safety Instructions 15 About Your Robocall What's in the Box Acrobat Anatomy Buttons & Indicators 19 Using Your Robocall Important Tips Before Use Preparation Charge Your Robocall Use Your Robocall with the Homeroom App Start / Pause Cleaning Select a Cleaning Mode Select a Suction Power Level Select BoostIQ™ feature Use Your Observance with Amazon Alexei / the Google Assistant 28 Cleaning and Maintenance Clean the Dust Collector and Filter Clean the Rolling Brush Clean the Si
02 Important Safety Instructions To reduce the risk of injury or damage, read these safety instructions carefully and keep them at hand when setting up, using, and maintaining this device. WARNING SYMBOLS USED This is the safety alert symbol. This symbol alerts you to potential hazards that could result in property damage | and/or serious bodily harm or death.
+ Do not operate this device in areas with exposed electrical outlets on the floor. » Do not expose the electronics of this device, its battery, or the integrated Charging Base. There are no user serviceable parts inside. + Do riot use this device on an unfinished, unsealed, waxed or rough floor. It may result in damage to the floor and this device. Use only on hard floor surfaces or low-pile carpet. « This device has been designed to be used on floors without scratching them.
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: (1) Reorient or relocate the receiving antenna. (2) Increase the separation between the equipment and receiver.
Consignes importantes de sécurité Pour réduire le risque de blessure ou de dommage, lisez attentivement les consignes de sécurité et gardez-les a portée de main lors de la configuration, [utilisation et I'entretien de cet apparie SYMBOLES D'AVERTISSEMENT UTILISES Il s'agit du symbole d'avertissement de sécurité. Ce symbole vous alerte sur les dangers potentiels qui peuvent entraîner des dommages matériels et/ou des lésions corporelles graves ou la mort.
d'un cordon d'alimentation et le traîne avec lui, un objet peut tomber d'une table ou d'une étagère. = Si la pièce a nettoyer possédé un balcon, une barrière physique doit être utilisée pour empêcher 'accès au balcon et garantir un fonctionnement sécurisé. + Ne rien placer sur le dessus de cet appareil. «+ Gardez a [esprit que cet appareil se déplace par ses propres moyens.
Déclaration FCC Cet appareil est conforme au Chapitre 15 du règlement FCC. Le fonctionnement est soumis aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de |'appareil doit accepter tout brouillage radioélectrique subi, mémé si celui-ci est susceptible d'en compromettre le fonctionnement.
Notes sur les marques déposées « Amazon, Écho, Alexa et tous les logos connexes sont des marques déposées Inc. ou de ses sociétés affiliées. « Apple et le logo Apple sont des marques commerciales d'Apple Inn, enregistrées aux États-Unis et dans d'autres pays. App Store est une marque de service d'Apple Inc, enregistrée aux États-Unis et dans d'autres pays. » Google Pelay et le logo Google Pelay sont des marques déposées de Google Inc. + Google Home est une marque déposée de Google Inc.
Robocall Anatomy C. Dust Collector A. Top & Side Filter Spot cleaning button [Recharge button Auto-cleaning Start/Pause button WI-Fi status light [— Bumper 3 D. Suction Inlet Infrared sensor Dust collector aly Man power switch (on/off Dust collector release button B. Bottom ET Suction nit Suetonius Charging Swivel wheel contact pins 5 E. Charging Base Side brush ring Path tracking sensor Drop sensors. Battery compartment Status ght Wheels BQ Rolling brush Brush guard .
Buttons & Indicators Start/Pause Cleaning Solid Blue: standby, cleaning, pause cleaning, returning to charging base or fully charged + Solid orange: standby or working in low battery status «+ Breathing orange (when docked to charging base): charging + Flashing red: error * Refer to the “Troubleshooting>Voice Alert” section in this manual for solutions.
Preparation € Remove the foam blocks beside the bumper before use. 0 Install the side brush before use. 20 oO Remove objects within 3 ft/1 m of the left and right side and within 6 ft/2 m of the front of the Charging Base. If you cannot remove the objects, check whether Robocall can return ta the Charging Base normally; if not, contact puffy customer service for help. = oO Connect the round connector of the adapter into the power socket on the Charging Base and the other end into a wall outlet.
Charge Your Robocall « Robocall has a per-installed rechargeable battery that has to be fully charged before use. « Robocall returns to the Charging Base at the end of a cleaning cycle or when its battery is running low. Method 1: Attach Robocall to the Charging Base by aligning its charging pins with the charging pins on the base. EE , + Turn off the main power switch if Bovary will not be used for a long i & period of time, To preserve the battery's lifespan, recharge ot least once. © every 6 months.
WI-Fi Status Light Slowly flashing blue Waiting for connection #5" | Rapid flashing blue | Connecting with your wireless router ® Solid blue Connected with your wireless router + IE you have any problems during the WI-Fi setup process, refer to the. & "Troubleshooting > WI-Fi connection” section in this Manual, + If Rorschach gets stick in any space, tap Find My Robot in the app to find the machine.
Press Pll on Robocall to start cleaning in Auto Mode. » In the Homeroom app, Bovary can be set to rectum fo the Charging Base automatically if the battery level becomes low. Once recharged, Robotize will resume to finish tha remaining cleaning. » By default, Robocall starts in Auto cleaning mode when it is tend on. Mains Spot cleaning Robocall intensively cleans a specific area in a spiral pattern, useful if there is a concentrated area of dust or debris.
+ For more information af Alexei / the Google Assistant, visit & i for details. Cleaning and Maintenance For optimal performance, follow the instructions below to clean and maintain Robocall regularly. The cleaning replacement frequency will depend on your usage habits of Robocall. Recommended claaning/replacement frequency LL Cleaning Frequency Replacement Frequency Dust Collector | After each use .
0 Push the dust collector back into the main unit. Clean the Side Brush Foreign substances, such 2s hair, can easily get tangled in the side brush, and dirt may adhere to it. Be sure to clean it regularly. €) Remove the side brush. Clean the Rolling Brush © Carefully unwind and pull off any hair or string that is wrapped between the main @ Pull the release tabs to unlock the brush guard as shown. unit and the side brush. 0 Lift the rolling brush to remove.
Replace the Side Brush The side brush may become bent or damaged after being used for a period of time. Follow the instructions below to replace it. + Pull off the old side brush and snap the new one into place. Clean the Sensors and Charging Pins To maintain the best performance, clean the drop sensors, path tracking sensor and charging pins regularly. « Dust off the sensors and charging contact pins using a cloth or cleaning brush. « Clean the path tracking sensor with a fast, dry cloth.
Troubleshooting ld pO + Make sure the main power switch is in the ON position. Robocall cannot be | + Make sure the battery is Ally charged. activated, » It you till have trouble, tum off the main power switch and then tum it back onc » Check if Robocall is trapped ar stuck on an obstacle. Removal stops + Check if the battery level is too low. working suddenly. + If you still have trouble, turn off the main power switch, wait for 2 seconds, and then turn it back on.
Voice Alert When an error or issue occurs, the red indicator on Robocall will flash and you will hear a specific voice prompt. Follow the voice prompt to solve the problem. Voice Prompt Cause and Solution Error 1: Front bumper stuck Front bumper is stick: Tap it repeatedly to remove any: dust; i1.not, then move the device 1o a new position and fry. again Voi pt Error $2: Wheel Module Error.
fy WI-Fi Connection Light ® se pL ELEGY Be lore Wi setup, make sure Robocall and your WI-Fi network meet the following Rorschach has corrected | hi Dil Defeated ie To your router. but Solid blue = Check with your Internet provider ta | not access the WI-Fi Setup Requirements ar . see iT there is any Internet connection « Robocall: problem, Acrobat is fully charged and the main power switch at the side of Robocall is « Check if you have modified your network turned an. Rob Ave t name and password. .