Cleaning For FAQs and more information, please visit: www.eufylife.
Table of Contents 02 Important Safety Instructions 04 About Your RoboVac What's in the Box RoboVac Anatomy LED Indication 09 Using Your RoboVac Important Tips Before Use Preparation Charge Your RoboVac Start / Stop Cleaning Select a Cleaning Mode Set Time and Scheduled Cleaning 17 Cleaning and Maintenance Clean the Dust Collector and Filters Clean the Rolling Brush Clean the Side Brushes Replace the Side Brushes Clean the Sensors and Charging Pins Clean the Swivel Wheel 22 Troubleshooting 24 Specifica
Important Safety Instructions To reduce the risk of injury or damage, read these safety instructions carefully and keep them at hand when setting up, using, and maintaining this device. • If the room to be cleaned has a balcony, a physical barrier should be used to prevent access to the balcony and to ensure safe operation. • Do not place anything on top of this device. WARNING SYMBOLS USED This is the safety alert symbol.
Consignes de Sécurité Pour réduire le risque de blessures ou de dommages, lisez attentivement ces consignes de sécurité et gardez-les en main lors de la mise en place, de l'utilisation et de l'entretien de cet appareil. SYMBOLES D'AVERTISSEMENT UTILISÉS Voici le symbole d'alerte de sécurité. Ce symbole vous avertit des dangers potentiels pouvant entraîner des dommages matériels et/ou des lésions corporelles graves ou la mort.
About Your RoboVac RoboVac Anatomy What's in the Box Top & Side Auto cleaning Start/Stop button Bumper RoboVac 11S Charging Base Remote Control (AAA Battery x2) Infrared sensor Dust collector Dust collector release button Bottom Power Adapter Cleaning Tool Side Brushes (x4) Charging contact pins Drop sensors Swivel wheel Side brushes Battery compartment Brush guard Rolling brush Additional High-Performance Filter 06 Additional Foam Filter Owner’s Manual & Other Documents Main power switch (O
Dust Collector Remote Control Start Auto cleaning Pre-filter Start Auto cleaning Stop cleaning Start Spot cleaning Start Edge cleaning High-performance filter 1 2 Foam filter 3 4 5 Suction Inlet Dust collector 6 Adjust time 7 Adjust suction power level in Auto/Single Room Cleaning mode Control cleaning direction manually Adjust the hour and minute Start Single Room cleaning 8 Return RoboVac to Charging Base 9 10 Schedule Auto cleaning start time Remote Control Display Returning to Charging
LED Indication Using Your RoboVac You can see the status of RoboVac from the LED indicator. Important Tips Before Use (Status Light) Status Breathing orange Charging Solid blue Standby / Cleaning / Fully charged Solid orange Low power and returning to Charging Base • RoboVac is off. Off • To conserve power, the light automatically turns off when RoboVac is not docked to the Charging Base and has been inactive for 1 minute. a b c d e f RoboVac has an error.
Preparation Remove objects within 3 ft/1 m of the left and right side and within 6 ft/2 m of the front of the charging base. Install the side brushes before use. Connect the round connector of the adapter into the power socket on the Charging Base and the other end into a wall outlet. • When the Charging Base connects to AC power, the LED indicator on the Charging Base is SOLID WHITE. Turn on the main power switch on the bottom of RoboVac.
Method 2: Press on the remote control to return RoboVac to the Charging Base. Select a Cleaning Mode 1. Auto cleaning RoboVac optimizes its cleaning path by selecting different cleaning modes automatically until cleaning is complete. This is the most commonly used cleaning mode. Press on RoboVac or / on the remote control to start cleaning in Auto Mode. Turn off the main power switch if RoboVac will not be used for a long period of time.
2. Spot cleaning 4. Single Room cleaning RoboVac intensively cleans a specific area in a spiral pattern, useful if there is a concentrated area of dust or debris. In Spot mode, RoboVac will stop cleaning after 2 minutes. RoboVac intensively cleans one single room and stops after 30 minutes. Select this mode only when one specific room needs to be cleaned. Make sure to confine RoboVac to the room by closing the door. Press on the remote control to start cleaning in Spot mode.
Set Time and Scheduled Cleaning Press to set the “hour” and “minute”. Note: Make sure AM/PM is set correctly. Set Time Press or to save the setting. RoboVac will BEEP ONCE to indicate the schedule has been set. Make sure the time is set correctly to your local time before setting a scheduled cleaning. ON Make sure the main power switch on the bottom of RoboVac is turned on. Press on the remote control. The time will blink on the display. Press 1 to set the “hour” and “minute”.
Clean the Dust Collector and Filters Push the dust collector back into the main unit. Press the dust collector release button to pull the dust collector out. Open and empty the dust collector. 1 2 You can wash the dust collector, pre-filter and foam filter with water. Be sure to air-dry them thoroughly before reassembling. Do not wash the high-performance filter with water, as it may damage the filter and reduce the suction power. Remove the pre-filter by pulling the hooks as shown.
Clean the Side Brushes Clean the Sensors and Charging Pins Foreign substances, such as hair, can easily get tangled in the side brushes, and dirt may adhere to them. Be sure to clean them regularly. To maintain the best performance, clean the drop sensors and charging pins regularly. • Dust off the drop sensors and charging contact pins using a cloth or cleaning brush. Remove the side brushes. Carefully unwind and pull off any hair or string that is wrapped between the main unit and the side brushes.
Troubleshooting Problems Solutions Frequently asked questions The rolling brush does not rotate. • Clean the rolling brush. • Check if the rolling brush and brush guard have been installed properly. RoboVac’s movements or travel path are abnormal. • Clean the sensors carefully with a dry cloth. • Restart RoboVac by turning the power switch off and on. Problems Solutions RoboVac cannot be activated. • Make sure the main power switch is in the ON position. • Make sure the battery is fully charged.
Specifications Product Model T2108 Input 19 V Battery Voltage DC 14.4 V Power Consumption 25 W Battery Type DC 14.4 V Li-ion 2600 mAh Dust Collector Capacity 0.6 L Cleaning Time Max. 100 mins Charging Time 300 - 360 mins Input 19 V 0.6 A Output 19 V 0.6 A 0.
