Owner’s Manual RoboVac T2130 51005001749 V01
Table of Contents 02 Important Safety Instructions 14 About Your RoboVac What's in the Box RoboVac Anatomy LED Indication 18 Using Your RoboVac Important Tips Before Use Preparation Charge Your RoboVac Use Your RoboVac with the EufyHome App Start / Stop Cleaning Select a Cleaning Mode Use the Boundary Strip Use Your RoboVac with Amazon Alexa / the Google Assistant 29 Cleaning and Maintenance Clean the Dust Collector and Filter Clean the Rolling Brush Clean the Side Brushes Replace the Side Brushes Clean
Important Safety Instructions To reduce the risk of injury or damage, read these safety instructions carefully and keep them at hand when setting up, using, and maintaining this device. WARNING SYMBOLS USED This is the safety alert symbol. This symbol alerts you to potential hazards that could result in property damage and/or serious bodily harm or death.
• Do not place anything on top of this device. • Be aware that this device moves around on its own. Take care when walking in the area where this device is operating to avoid stepping on it. • Do not operate this device in areas with exposed electrical outlets on the floor. • Do not expose the electronics of this device, its battery, or the integrated Charging Base. There are no userserviceable parts inside. • Do not use this device on an unfinished, unsealed, waxed or rough floor.
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
Consignes importantes de sécurité Pour réduire le risque de blessure ou de dommage, lisez attentivement les consignes de sécurité et gardez-les à portée de main lors de la configuration, l'utilisation et l'entretien de cet appareil. SYMBOLES D'AVERTISSEMENT UTILISÉS Il s'agit du symbole d'avertissement de sécurité. Ce symbole vous alerte sur les dangers potentiels qui peuvent entraîner des dommages matériels et/ou des lésions corporelles graves ou la mort..
d'un cordon d'alimentation et le traîne avec lui, un objet peut tomber d'une table ou d'une étagère. • Si la pièce à nettoyer possède un balcon, une barrière physique doit être utilisée pour empêcher l'accès au balcon et garantir un fonctionnement sécurisé. • Ne rien placer sur le dessus de cet appareil. • Gardez à l'esprit que cet appareil se déplace par ses propres moyens. Faites attention en marchant dans la zone où cet appareil fonctionne, afin d'éviter de marcher dessus.
Déclaration FCC Cet appareil est conforme au Chapitre 15 du règlement FCC. Le fonctionnement est soumis aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si celui-ci est susceptible d'en compromettre le fonctionnement.
About Your RoboVac RoboVac Anatomy What's in the Box A. Top & Side Wi-Fi status light Auto cleaning Start/Stop button Bumper RoboVac Charging Base Remote Control (AAA Battery x 2) Infrared sensor Dust collector Dust collector release button Power Adapter Side Brushes (x4) Additional Filter B. Bottom Charging contact pins Drop sensor Hall sensors Swivel wheel Side brushes Cleaning Tool Cable Ties (x5) Boundary Strips 6.
C. Dust Collector Remote Control Filter 2 1 3 D. Suction Inlet 4 1 Return RoboVac to Charging Base 2 Adjust suction power level 3 Start Auto cleaning / Stop cleaning 4 Control cleaning direction manually 5 6 5 Start Auto cleaning 7 8 6 Start Edge cleaning 7 Start Spot cleaning 8 Start Quick cleaning Dust collector Install 2 AAA batteries before using the remote control for the first time.
(Wi-Fi Status Light) Anti-drop sensors will prevent RoboVac from tumbling down stairs and steep drops in most cases. Sensors are less effective if dirty or used on carpeted/reflective/very dark-colored floors. It is recommended to apply the Boundary Strip(s) to block off areas where RoboVac may fall.
3 Place the Charging Base on a level surface and against a wall. Method 1: Attach RoboVac to the Charging Base by aligning its charging pins with the charging pins on the base. - Install the Charging Base in a location that RoboVac - Always keep the Charging Base plugged in, otherwise 4 Remove objects within 3 ft/1 m of the left and right side and within 6 ft/2 m of the front of the Charging Base.
• RoboVac is attached to the Charging Base to ensure it has enough power during setup. Schedule Cleaning With the EufyHome app, you can schedule RoboVac to start cleaning at a particular time. You can set the time and customize the cleaning schedules from Sunday to Saturday on the EufyHome app. This function is available in the app only. EufyHome EufyHome Start / Stop Cleaning 1. Download the EufyHome app from the App Store (iOS devices) or Google Play (Android devices). 2.
Press on RoboVac or / on the remote control to start cleaning in Auto Mode. 2. Spot cleaning RoboVac intensively cleans a specific area in a spiral pattern, useful if there is a concentrated area of dust or debris. In Spot mode, RoboVac will stop cleaning after 2 minutes. Press on the remote control to start cleaning in Spot Mode. - RoboVac will return to the Charging Base automatically when the battery level becomes low or when RoboVac finishes cleaning.
4. Quick cleaning RoboVac will automatically stop cleaning after 30 minutes and return to the Charging Base in this mode. If any small room or area needs to be cleaned, it is recommended to select this mode to save time and power. Press on the remote control to start quick cleaning mode. Use the Boundary Strip With the Boundary Strip, you can keep RoboVac away from any area or item you do not want RoboVac to clean. RoboVac will recognize the Boundary Strip and will not cross into the blocked-off area. 1.
Use Your RoboVac with Amazon Alexa / the Google Assistant Currently this feature only supports English, German, French, and Spanish. You could check regularly if more languages are supported at https://www.eufylife.com/support/. Cleaning and Maintenance For optimal performance, follow the instructions below to clean and maintain RoboVac regularly. The cleaning/replacement frequency will depend on your usage habits of RoboVac.
3 Remove the filter. Clean the Rolling Brush 1 Pull on the release tabs to unlock the brush guard as shown. 2 Lift the rolling brush to remove. 3 Clean the rolling brush with the provided cleaning tool or a vacuum cleaner. 4 Reinstall the rolling brush by inserting the fixed protruding end first and then clicking into place. 5 Press down to snap the brush guard into place. 4 Tap the filter to remove dust. 1 2 4 5 3 5 Place the filter back into the dust collector.
3 Use a cloth dampened with warm water to remove dust from the brushes or to gently reshape them. Clean the Sensors and Charging Pins To maintain the best performance, clean the drop sensors and charging pins regularly. • Dust off the drop sensors and charging contact pins using a dry cloth or cleaning brush. - Only use the side brushes when they are completely dry.
Troubleshooting Problems RoboVac cannot be activated. • Make sure the main power switch is in the ON position. • Make sure the battery is fully charged. • Replace the batteries (2 AAA) in the remote control. • Make sure the remote control is within range (16 ft/5 m) of RoboVac. • If you still have trouble, turn off the main power switch and then turn it back on. • Replace the batteries in the remote control. • Make sure RoboVac is turned on and fully charged. RoboVac stops working suddenly.
Problems Solid red indicator light Solutions • Check if there are any Internet connection problems. You cannot control RoboVac with the Google Assistant. • Check if you have installed the Google Home app onto your smart device and initiated the “EufyHome” action in the Google Home app. For details, refer to the “Smart Integrations” page in the EufyHome App. • Check if you are using the proper commands when talking to the Google Assistant. When making your request, first say the wake words “Ok Google”.
Wi-Fi Channels - The FCC requires that all wireless devices in the United States operate on the 1-11 wireless spectrum channels. - Some countries outside North America can use spectrum channels higher than channel 11. Refer to your local regulatory agency to determine which channels are accessible. - A future software release will support access to channels above 11 for users outside North America. Until then, use channels 1-11.
