Gufy SECURITY QUICK START GUIDE Video Doorbell 2K (Battery-Powered) • 0 0ufy SECURITY
TABLE OF CONTENTS What's Included Product Overview How The System Works Verifying Your Homebase Adding The Doorbell To Your Existing System Determining The Power Option Finding A Mounting Spot O2 I O Mounting The Bracket O3 I 3 Mounting The Doorbell 04 I 4 Detaching The Doorbell Q5 I5 Charging The Doorbell Q5 16 Q6 24 Powering The Doorbell With Existing Doorbell Wires Notice O8 English OI
WHAT'S INCLUDED For Video Doorbell Installation u 0 @) D D D D 0 @) •(@) • 0 ·~ cvfy 0 Video Doorbell 2K (Battery-Powered) (@) Mounting _Bracket Screw Hole Positioning Card 15° Mounting Wedge (Optional) Model: T82 I 0 FCC ID: lAOKB-T82 I 0 IC: 2345 I-T82 I 0 Jumper for Original Chime (Optional) Extension Wires and Wire Nuts (Opti~nal) QSG Screw Packs (Spare screws and anchors are included) 02 English Quick Start Guide USB Charging Cable Doorbell Detaching Pin
PRODUCT OVERVIEW Video Doorbell (Battery Powered) Front view: f) - I . Motion Sensor 8 2. Microphone 3. Camera Lens o- - 0 4. Ambient Light Sensor 5. LED Ring 6. Doorbell Button 7. Speaker 8 00000. - - , Rear View: c::::> G- " 03-~ 0 6 €) I . Micro USS Charging Port 2. SYNC/RESET Button 3. Power Terminals for Existing Doorbell Wire (Optional) 4. Detaching Mechanism J I t::::::::r - -- .
HOW THE SYSTEM WORKS How the System Works The video doorbell system includes 2 parts. One is the video doorbell at your door. The other is the HomeBase in your house. The video doorbell detects motion at your porch and allows you to answer the door anytime and anywhere. The HomeBase stores video clips on its built-in storage. When someone rings the doorbell, people in the house will be notified. Doorbell Chime □ EE3 • • • • • ~ Cl ' ◄Video D oorbell 04 English --.
STEP I VERIFYING YOUR HOMEBASE Verify Your HomeBase The battery-powered video doorbell cannot work without a HomeBase or eufyCam series system. Make sure you have an existing eufyCam series system installed and working. Your video doorbell will be connected to the network where the Homebase is connected to, and added to the existing HomeBase system. Video clips captured at your door will be saved and viewed using the system.
STEP 3 DETERMINING THE POWER OPTION ' Option I - Battery Powered I. If you don't have existing doorbell wiring at the front door, use the built-in battery. You are free to determine the doorbell position and the mounting is easy and quick. 2. 3. When the doorbell battery level is low, you need to detach and charge it. If you choose this option, please jump to STEP 4 FINDING A MOUNTING SPOT.
Option 2 - Doorbell Wire Powered I. If you have existing and working doorbell wiring at the front door, the doorbell will be powered by the wires constantly. So you don't need to detach and charge it after installation. 2. Since the doorbell is connected to the wires, the mounting position is limited. 3. If you choose this option, please jump to Appendix 3 Powering the Doorbell with Doorbell Wires. - =:::::::::::: ::----.
STEP 4 FINDING A MOUNTING SPOT Find a Mounting Spot Take the video doorbell to your front door and check the live view on the App at the same time. Find a location where you can get the desired field of view. Consider the below factors: I. Check if you can reuse the existing holes and anchors on the wall or door frame. 2. If you want to place the doorbell close to a side wall, make sure the wall doesn't show up in the field of view.
Place the Screw Hole Positioning Card against the wall to mark the position.
STEP 5 MOUNTING THE BRACKET Mount the Doorbell on a Wooden Surface If you're mounting the doorbell on a wooden surface, you don't need to pre-drill pilot holes. Use the provided screws to secure the Mounting Bracket on the wall, The Screw Hole Positioning Card indicates the position of the screw holes. What is required: Screwdriver, Mounting Bracket, I S0 Mounting Wedge (Optional), Screw Pack @) D ... ,, c:: D D litc:1) 1;;,;---~ c::(;:::O ~ ~ @) : , ________________ ,I .-ldlrt Mounr1rc \ ~ t o JS
Mount the Doorbell on Surfaces Made Out of Hard Materials I. If you•re mounting the doorbell on a surface made out of hard materials, like brick, concrete, stucco, drill 2 holes through the Screw Hole Positioning Card with a 15/64"(6mm) drill bit. 2. Insert the provided anchors, and then use the provided long screws to secure the Mounting Bracket on the wall. What is required: Power Drill, 15/64"(6 mm) Drill Bit, Mounting Bracket, I5° Mounting Wedge (Optional), Screw Pack , .........•...... , o .....
Wall · -:t tttfftttl 0 -»iWJW 0 Mounting Bratket Without 15° MountingWedge • 12 English 0 - --
STEP 6 MOUNTING THE DOORBELL Mount the Doorbell Align the doorbell on top and then snap it on the bottom. Press it down until it clicks into place. You're all set! If you want to detach the doorbell or recharge it, please refer to the following sections.
APPENDIX I DETACHING THE DOORBELL Detach the Doorbell What is required: Doorbell Detaching Pin Ooort,oll OouchffwPin '---------------- 14 English
APPENDIX 2 RECHARGING THE DOORBELL Recharge the Doorbell = •.....
APPENDIX 3 POWERING THE DOORBELL WITH EXISTING DOORBELL WIRES 3.1 Verify whether the doorbell wires are working I. Ring the existing doorbell to check if it is working. If the doorbell doesn't ring, your doorbell wires may be defective. Power the doorbell on its battery or consult an electrician to fix the wires. 2. Shut off power at the breaker. Turn the lights on / off in your home to make sure the electricity in your house is properly shut off. .
2. Pull the two wires out carefully when removing the existing doorbell. Straighten the wire ends if necessary. What is required: Philips-Head Screwdriver ,,•---············~ •• ' ••' ' '' ' ' ' ••' : . • • ~-Ht,d s.a-.-..,,,,... ,u..r l'"""N"'-1 • .···········---·- ,•• 3.3 Find a Mounting Spot I. Determine the mounting position of the doorbell. Consider the below factors: (f Check if you can reuse the existing holes and anchors on the wall or door frame.
® Use the 15° mounting wedge as a supplementary mounting bracket if you wish to see more on a specific side. Without 15° Mounting wedge 2. W ith Is• Mounting wedge Place the Screw Hole Positioning Card against the wall to mark the position.
3.4 Mount the Bracket If you're mounting the doorbell on a wooden surface, you don't need to pre-drill pilot holes. Use the provided screws to secure the Mounting Bracket on the wall. The Screw Hole Positioning Card indicates the position of the screw holes. What is required: Power Drill, Mounting Bracket, 15° Mounting Wedge (Optional), Screw Pack D (@) ________________ , t '---------------- - -•◄ •nzzzzv O Ywall D D 0 ~ ~ ~ IS"MOtJNlf'C (A
If you're mounting the doorbell on a surface made out of hard materials, like brick, concrete, stucco: (J) Drill 2 holes through the Screw Hole Positioning Card with I 5/64"(6mm) drill bit. Q) Insert the provided anchors, and then use the provided long screws to secure the Mounting Bracket on the wall. What is required: Power Drill, I 5/64"(6mm) Drill Bit, Mounting Bracket, 15° Mounting Wedge (Optional), Screw Pack ........................ , :··--------------\ ... .'.' .. . '. . ' .
Wall .
3.5 Connect the Doorbell Wires to the Doorbell Connect the wires to the terminals at the back of the doorbell, then tighten the terminal screws.Wire can connect to any terminal. What is required: Wires and Wire Nuts (Optional) / Video Doorbell / Philips-head Screwdriver , ........... ...,,•------·--------, ' . .' o I '' ' ' '' ' !~! ''' ' 0 • ~ Oo..,,W )JC (Wnd' : Mo61i1TS110 '··········------'' .-- ...................... ·-I ' 0 . --------, ,-·--------------, ' . .
3.6 Mount the Doorbell on the Bracket Align the doorbell on top and then snap it on the bottom. i 3.7 Restore Power Switch the master circuit breaker back to ON. I I I I I I L__ You're all set! If you want to detach the doorbell or recharge it. please refer to the corresponding sections.
NOTICE FCC Statement This device complies with Part I 5 of the FCC Rules. Operation is subject to the following two conditions: (I) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
CE This product complies with the radio interference requirements of the European Community. D eclaration of Conformity Hereby, Anker Innovations Limited declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. For the declaration of conformity, visit the Web site: https://www.eufylife.com/. This product can be used across EU member states.
IC Statement This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (I) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device." Le present appareil est conforme aux CNR d'lndustrie Canada applicables aux appareils radio exempts de licence.
CUSTOMER SERVICE Kundenservice Klantenservice I Servicio de atenci6n al cliente I Service client I Servizio clienti Warranty Garantie I Garantia I Garantie I Garanzia I Garantie 12-month limited warranty 12 Monate eingeschrankte Garantie ~ ~ Garantia limitada de 12 meses Garantie limitee de 12 mois Garanzia limitata di 12 mesi I 2 maanden beperkte garantie + I (800) 988 7973 Mon-Fri 9AM-SPM (PT) (6 +44 (0) 1604 936 200 Mon-Fri 6AM-1 IAM (GMT) +49 (0) 69 9579 7960 Mon-Fri 6:00-11 :00 ~ Customer
0 0 @EufyOfficial • eufyofficial @EufyOfficial
SECURITY Anker Innovations Limited.All rights reserved. eufy Security and eufy Security Logo are trademarks of Anker Innovations Limited, registered in the United States and other countries.All other trademarks are the property of their respective owners.
Step4
AUSTRALIA & NEW ZEALAND WARRANTY This document details the terms and conditions of the warranty provided with this product.Please disregard any other arepresentations contained on this product's packaging or provided with this product, which constitute or appear to constitute a warranty.