NES510 series Corded stick vacuum cleaner; household type Owner’s Guide Thank you for purchasing your new Eureka vacuum! Important instructions For easy assembly, please take a few moments to read this owner’s guide. If you have questions about your new vacuum, please contact our customer service HELPLINE at 1-800-282-2886. We’re here to help! Eureka stands by our Clean Promise seal. Learn more at www.eureka.com/cleanpromise www.eureka.
Where to find important vacuum information Keep this information Write the model, type and serial number here: Date of purchase (keep your receipt) ______________ Model number and type _________________________ Serial number ________________________________ Find these numbers on a label on the hand vacuum. Refer to these numbers when ordering parts and accessories, or if service is needed.
IMPORTANT SAFEGUARDS When using an electrical appliance, basic precautions should always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS VACUUM CLEANER Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. WARNING •Prevent unintentional starting. Ensure the switch is in the off-position before picking up or carrying the appliance.
What comes in the carton Storage base Hand vacuum (comes as two separate pieces must be assembled) OWNER’S GUIDE Important safeguards 2-in-1 upholstery tool Motorized floor nozzle Wand 4 Eureka Customer Service HELPLINE 1-800-282-2886 Crevice tool
How to identify parts of your vacuum cleaner Corded vacuum cleaner Hand vacuum On/Off and brushroll mode switch Filter cover (pre-motor filter inside) Power and brushroll mode switch Filter cover release button Detachable hand vacuum Handle Nozzle One click dust cup release button Release button for hand vacuum Filter assembly (inside dust cup) Filter cover release button Post-motor filter cover (post-motor filter inside) Power cord Wand For filter maintenance instructions, see page 9 Woven fil
Easy assembly 3 1. Slide wand onto hand vacuum Tool base assembly until it clicks (Fig. 1). 2. Push wand into motorized floor nozzle until it clicks (Fig. 2). How to use storage base 1. Insert storage base shaft into slot on base until it clicks into place. Ensure side of shaft that says Floor Nozzle goes in the same side as wheel well. Click! 1 2. Detach hand vacuum from wand 3. Keep wand attached to floor nozzle and place in the wheel well rest on storage base Click! 4.
How to use cleaner for cleaning floors 1 Power button/ 2 speed controls 1. Move power switch on handle to the first position for bare floor cleaning and second position to engage brushroll for carpet cleaning (Fig 1) 2. Using motorized floor nozzle, glide back and forth on area to be cleaned. Avoid oversized or sharp items (such as screws) with cleaner. 1. Release latch 2. Pull out 3. Twist wrist to engage swivel function. 4. When done, switch to off position Empty dust cup after every use 1.
How to use hand vacuum and accessories (continued) Use with or without wand. • 2-in-1 upholstery tool: Use brush to vacuum blinds, vents or upholstered surfaces. Use felt portion to clean delicate surfaces. To switch between felt and brush portions, press thumb release and slide brush up or down. How to use hand vacuum and motorized floor nozzle Ideal for cleaning stairs. • Press release button to remove wand from hand vacuum. Attach motorized floor nozzle directly to hand vacuum until it clicks.
How to maintain your vacuum cleaner ! CAUTION Dust cup – Empty after each use Never operate vacuum cleaner without all filters, filter screen and dust cup in proper position. 1. Release latch 2. Pull out WARNING: Moving parts! Click the dust cup release button, located on the bottom of the dust cup to detach it from the unit, and pull dust cup out. Use handle on top of dust cup to remove lid, empty dust cup and replace lid. Washable pre and post-motor filters - clean regularly 1. Release latch 2.
The Eureka three year limited warranty Midea America Corp. (“Eureka”), subject to the terms and conditions herein, warrants this vacuum cleaner to be free from defects in material and workmanship for a term of three years from the date of original purchase when used in accordance with the Eureka operating and maintenance instructions and under normal household usage.
! Problem solving Make sure vacuum cleaner is off and charging plug is unplugged. N O T I C E : Thermal cut-off This vacuum cleaner has a special thermostat that protects the vacuum cleaner in case of motor overheating. If the vacuum suddenly shuts off, proceed as follows: 1) Check the vacuum for a possible source of overheating such as a full dust cup, blocked wand or clogged filters. If these conditions are found, fix them and wait at least 30 minutes before attempting to use the vacuum.
Order genuine Eureka accessories and replacement parts Visit www.eureka.com or call 1-800-282-2886 Image Part # (fits models) Part name Crevice tool Z0101 (all) Floor nozzle N0201 Wand N0202 2-in-1 upholstery tool 12 Z0201 (all) Brush roll Z0208 Base shaft N0203 Lower base N0204 Inlet filter N0205 Woven filter N0206 Outlet filter N0207 © 2019 Midea America Corp.
