rangehoods USAGE AND CARE GUIDE PRODUCT CODE: EBB900BK3R
Contents Safety Instructions 3 Installation 5 Start using your cooker hood 7 Troubleshooting 8 Maintenance and Cleaning 9 Environment Protection 11 2
SAFETY INSTRUCTIONS This manual explains the proper installation and use of your cooker hood, please read it carefully before using even if you are familiar with the product. The manual should be kept in a safe place for future reference. Never to do: • • • • Always to do: • Important! Always switch off the electricity supply at the mains during installation and maintenance such as light bulb replacement.
Always to do: Always to do: • Always put lids on pots and pans when cooking on a gas cooker. • When in extraction mode, air in the room is being removed by the cooker hood. Please make sure that proper ventilation measures are being observed. The cooker hood removes odours from room but not steam. • Cooker hood is for domestic use only. • Caution: The appliance and its accessible parts can become hot during operation. Children should stay away unless they are under permanent supervision.
INSTALLATION (VENT OUTSIDE) MOUNTING OF THE V-FLAP If the cooker hood does not have an assembled V-flap 1, you should mount the halfparts to its body.The images only show an example of how to mount the V-flap,the outlet may be various according to different models and configuration.
3. Install the hook on a suitable place once the installation height is fixed, and keep it in line. The fixed position of the inside chimney bracket is the place of chimney. See pic 2. 4. Fix the outside chimney bracket on the outside chimney, and be sure that the inside chimney can be adjusted the height in it freely as well as fixing the expansion pipe. Afterwards,fix the outlet with screws and put the expansion pipe with the cable tie on the outlet.Then install the chimneys on the cooker hood. See Pic 3.
• Failure to observe these basic instructions will reduce the performance and increase noise levels of the cooker hood. • Any installation work must be carried out by a qualified electrician or competent person. •Do not connect the ducting system of the hood to any existing ventilation system which is being used for any other appliance ,such as warmer tube, gas tube , hot wind tube.
again to close it, and its indicator light will be off. All the function operation of the hood will be closed, the hood enters into standby mode, and run by circle. The speed buttons and lamp button can work separately and not controlled by the power button. When a certain function button is pressed, the hood operates at that function status. Press power button switched off without any functions. 3. Press lamp button button once; lights will be turn on.
Light does not work, motor does not work Oil leakage Lights not working Insufficient suction The Cooker hood inclines House fuses blown Reset/Replace fuses. Power cord loose or disconnected Refit cord to power outlet. Switch power outlet on. One way valve and the outlet are not tightly sealed Take down the one way valve and seal with sealant. Leakage from the connection of chimney and cover Take chimney down and seal. Broken/Faulty globes Replace globes as per this instruction.
CONTROL PANEL SURFACE The inlay control panel can be cleaned using warm soapy water. Ensure the cloth is clean and well wrung before cleaning. Use a dry soft cloth to remove any excess moisture left after cleaning. Important Using neutral detergents and avoid using harsh cleaning chemicals, strong household detergents or products containing abrasives,as this will affect the appliance appearance and potentially remove any printing of artwork on the control panel and will void manufactures warrantee.
Changing the lights: • Remove the grease filter. • Use a tool or the hand to press the spring splinter of both sides of LED light to the inside, until the light is pressed out, see pic 1.Then slightly pull the light connecting wire out, and dismantle the terminal of the light connecting wire. See pic 2. • Apply the reverse procedure to install the light back. • ILCOS D code for this lamp is: DSR-1.5/65-S-64 – LED modules, self- ballasted – round lamp – Max wattage: 2×1.
Pronto Service + Support: 1800 440 335 Email: service@eurostylegroup.com.au HEAD OFFICE 65 Glynburn Road, Glynde SA 5070 Ph: 08 8165 1012 www.euroappliances.com.