EUROBOOR FOR PROFESSIONALS BY PROFESSIONALS USER MANUAL ECO.50 Magnetic Drilling Machine SERIAL NO.
Congratulations on your purchase of the Euroboor ECO.50 Portable Magnetic Drilling Machine. Your model is designed to produce superior holes quickly and efficiently. Through years of experience, constant innovation and development, Euroboor BV is committed to provide you with metal cutting tools and products to help you be more productive. Before operating your new magnetic drilling machine, please read all instructions first. These include the Operator’s Manual and Warning Label on the unit itself.
Fig.
Symbol Term, meaning Explanation Read documentation Be absolutely sure to read the enclosed documentation such as the Instruction Manual and the General Safety Instructions. Wear ear protection Use ear protection during operation. Wear eye protection Use eye-protection during operation. Danger/warning/caution Observe the information in the adjacent text! European conformity symbol Confirms the conformity of the power tool with the directives of the European Community.
GENERAL POWER TOOL SAFETY WARNINGS Do not use this power tool before you have thoroughly read and completely understood this Instruction Manual and the “General Safety Instructions”, including the figures, specifications, safety regulations and the signs indicating DANGER, WARNING and CAUTION. WARNING: When using electrical tools basic safety precautions should always be followed to reduce the risk of fire, electrical shock and personal injury including following.
4. Never place hands, fingers, gloves or clothing near cutting area or rotating machine parts. 5. Remove adjusting keys or switches before turning the machine on. A wrench or a key that is left attached to a rotating part of the machine may result in personal injury. 6. Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enables better control of the magnetic drilling machine in unexpected situations. 7. Use safety equipment. Always wear eye protection.
ADDITIONAL SPECIFIC SAFETY RULES FOR MAGNETIC DRILLING MACHINES • Keep your fingers well out of the drill area; • Avoid touching the drilled core that is automatically ejected by the centering pin when the working procedure is finished. Contact with the core when it is hot, or if it falls, can cause personal injuries; • Always use the drill guard.
Markings on Tool The following pictograms are shown on the tool: Read instruction manual before use. Wear ear protection in areas with noise emissions > 80 db(A). Wear eye protection. POSITION Serial number The Serial Number, which also includes the type of machine, the year and month of manufacturing and identification number, is engraved on the frame, magnet and the motor unit.
TECHNICAL DATA ECO.
DESCRIPTION (fig. 1) WARNING: Never modify the power tool or any part of it. Damage or personal injury could result. 1. 2. 3. 4. 5. 6.
EXTENSION CABLE If an extension cable is required, use an approved 3-core extension cable suitable for the power input of this tool (see technical data).The minimum conductor size is 1.5 mm²; the maximum length is 30 meter. When using a cable reel, always unwind the cable completely. ASSEMBLY AND ADJUSTMENTS WARNING: To reduce the risk of injury, turn unit off and disconnect machine from power source before installing and removing accessories, before adjusting or changing set- ups or when making repairs.
INSERTING AND REMOVING AN ACCESSORY (FIG. 1) The tool holder accepts annular cutters with a 19,05 mm Weldon shank with one or more flats. WARNING: The teeth of a cutter are very sharp and can be dangerous. 1. 2. 3. 4. 5. In order to fit an annual cutter it is necessary to remove the guard (1); Slide the pilot pin through the hole in the center of the cutter shank. Insert the shank of the accessory as far into the tool holder as possible.
TURNING MACHINE ON AND OFF THE CONTROL PANEL The control panel on your magnetic drilling machine is designed for maximum operating facility and safety. 1 - The Motor Switch: This switch is used to switch the motor unit ON and OFF; 2 - The Magnet LED Indicator: This LED indicator shows the generated magnetic force; 3 - The Magnet Switch: This switch is used to switch the magnet On and Off. Fig. 2 In order to operate properly, the machine has to be turned on following the procedure as described below.
DRILLING A HOLE Now that you have read the explanatory information and safety recommendations above, you are ready to actually start drilling. Follow these 10 steps for best drilling result : 1 Use the tip of the pilot pin to determine the center of the hole to be drilled. 2 Turn the magnet on and verify that the drill is in the right position and that the machine is pushed tight against the work piece. Check if the LED light is green.
Some materials of low hardness contain abrasive substances leading to rapid cutting edge wear at high speeds. Feed rates are governed by rigidity of set-up, volume of material to be removed, surface finish and available machine power. LUBRICATION IN HORIZONTAL APPLICATIONS Adjust the fluid flow as required using the flow regulator; Add more cutting fluid if the shavings (metal chips) become blue. VERTICAL AND OVERHEAD APPLICATIONS Dip the cutter in cutting paste or apply an appropriate spray.
MAINTENANCE Your EUROBOOR power tool has been designed to operate over a long period of time with a minimum of maintenance. Continuous satisfactory operation depends upon proper tool care and regular cleaning. CAUTION: To reduce the risk of injury, turn unit off and disconnect machine from power source before installing and removing accessories, before adjusting or changing set- ups or when making repairs. Be sure the switch is in the OFF position. An accidental start-up can cause injury.
ADJUSTMENT OF SLIDE An essential requirement of the machine is that the slide can move in a smooth and controlled manner, free of lateral movement and vibration. This situation can be maintained by periodic adjustment of the slide and is accomplished in the following manner: 1. Place the machine in an upright position and, by means of the capstan, raise the slide to its highest position. Clean the brass rail strips and apply a small amount of light machine oil to the wear surfaces. 2.
TROUBLE SHOOTING Magnet and motor do not function Magnet does function, the motor does not work Magnet does not function, the motor does Annular cutters break quickly, holes are bigger than the hole cutter Motor running roughly and/or seizing up Motor starts running when magnet switch is turned on Motor making a rattling sound Motor humming, big sparks and motor has no force Motor does not start or fails.
Frame under voltage - Damaged / defective wiring - Defective magnet - Motor seriously dirty Fuse blows when magnet switch is - Damaged or defective wiring turned on - Wrong value fuse - Defective magnet switch - Defective Control Unit - Defective magnet Fuse blows when motor is started - Damaged or defective wiring - Wrong value fuse - Motor running roughly - Defective Armature and / or Field - Carbon brushes worn out - Defective Control Unit Rotation system free stroke too - Loose or defective gear-rack l
SPARE PART LIST AND EXPLODED VIEW of ECO.50 Nr.: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 51 52 53 54 55 56 57 58 59 60 61 Article: 020.0056 020.0106 020.0111 020.0096 020.0091 050.0611 020.0201 050.0011 032.0016 020.0156 050.0141 020.0146 040.0041 020.0086 020.0084/4 020.0061 020.0077 020.0081 020.0066 020.0046 020.0041 020.0031 020.0036 020.0182 PP.RSEU 020.0101 PP.50EU 020.0206 020.0006 020.0016 020.0017 020.0011 020.0001 020.0002 020.
EXPLODED VIEW of ECO.
ISSUE 1/Original version/MARCH 2013 22
CE/EMC DECLARATION OF CONFORMITY DECLARING: EUROBOOR BV Kryptonstraat 110 Zoetermeer The Netherlands that the following Appliance complies with the appropriate basic safety and health requirements of the EC Directives based on its design and type, as brought into circulation by EUROBOOR BV. Designation/ function Magnetic Drilling Machine Type ECO.50 Ratings and principal Characteristics 230-240V, 50/60Hz, Class I ECO.
