USER MANUAL TO REDUCE THE RISK OF INJURY USER MUST READ AND UNDERSTAND INSTRUCTION MANUAL ECO.50 Magnetic Drilling Machine SERIAL NO.
1 - Table of Contents 1 2 3 4 4 4 5 6 Table of Contents …………………………………………………………………………………………………… Safety …………………………………………………………………………………………………………………….. Before Use ……………………………………………………………………………………………………………… Items Included in Delivery ………………………………………………………………………………………. The Hole Cutter Hole Cutter Selection ................................................................................................. Cooling/Lubrication .......................................................................................
please contact your supplier 2 - Safety 1. During any work on non-horizontal components, the machine must always be secured with the supplied safety chain. 2. The magnetic drilling machine may only be used on a flat and clean foundation. 3. If the machine or the lead show signs of damage, the magnetic drilling machine must be switched off immediately. 4. Wearing safety glasses, hearing protection and protective clothing is necessary. 5.
Before use Euroboor magnet drilling machines are specially designed for drilling holes is steel, possibly expanded by the possibility of tapping/reaming/countersinking (depending on model). Euroboor magnetic drilling machines may not be adapted and/or used for applications other than those they were designed for, including driving other machines. Make sure that you can oversee the entire work areas from where you are operating this machine. Use barriers to keep others away.
4 - The Hole Cutter Hole Cutter selection There are many different types of steel. It is not possible to drill all these types of steel with 1 type of cutter.
Cooling/Lubrication 1 2 Holes for cooling and lubrication oil Fixing screws of Morse Conus Euroboor recommends the use of cooling and lubrication agents. Not only do these assist in drilling but they will also lengthen the lifespan of your tools. One of the advantages of the use of hole cutters is that cooling and lubrication agent scan be supplied from the inside, so that the agents end up in the right place.
fixing screws of your spindle (see number 2 in picture of cooling/lubrication. Tighten them both subsequently with the included 5mm Allen Key. Drill Chuck Assembly The option of making our machines suitable for the use of standard spiral drills and other tools by using a cylindrical shaft is an important characteristic of Euroboor magnetic drilling machines. Please see the technical data for maximum capacity. Installation of 13mm Chuck by using adapter IBK.14 The IBK.
machines on pipes, not-flat or non-magnetic materials, we refer to our brochure or our website www.euroboor.com where several vacuum tightening systems and pipe clamping systems are mentioned. The Control Panel The control panel on your magnetic drilling machine is designed for maximum operating facility and safety. 1 - The Magnet Switch: This switch is used to switch the main power and also the magnet On and Off.
Drilling Now that you have read the explanatory information and safety recommendations above, you are ready to actually start drilling. Follow these 10 steps for best drilling result : 1 Use the tip of the pilot pin to determine the center of the hole to be drilled. 2 Turn the magnet on and verify that the drill is in the right position and that the machine is pushed tight against the work piece.` 3 If your machine is equipped with a auto coolant system, put open the valve to release the oil.
5 - Maintenance Just as every magnetic drilling machine with moving parts, your Euroboor magnetic drilling machine also needs regular maintenance service. A few recommendations follow : - Clean all dirt, dust, metal chips and burrs of your magnetic drilling machine - Regularly check the carbon brushes for wear - Replace any defective parts immediately. This prevents properly function parts from being damaged. - Adjust your guide regularly and make sure it is clean and greased.
6 - Spare parts & Exploded view of ECO.50 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 020.0056 020.0106 020.0111 020.0096 020.0091 050.0611 020.0201 050.0011 032.0016 020.0156 050.0141 020.0146 040.0041 020.0086 020.0084/4 020.0061 020.0077 020.0081 020.0066 020.0046 020.0041 020.0031 020.0036 020.0182 PP.RSEU 020.0101 PP.50EU 020.0206 020.0006 020.0016 020.0017 020.0011 020.0001 020.0002 020.0037 050.0101 050.0102 050.
Important notice : Because of minor changes to our machines it is recommended to provide the framenumber of your machine when ordering spareparts. This number can be found on front of machine at magnetic base and frame. When you have any doubt when ordering spareparts, please contact your supplier before ordering.
