A110EU SERVICE MANUAL
Preface LCD Computer A110EU Service Manual Preface I
Preface Notice The company reserves the right to revise this publication or to change its contents without notice. Information contained herein is for reference only and does not constitute a commitment on the part of the manufacturer or any subsequent vendor. They assume no responsibility or liability for any errors or inaccuracies that may appear in this publication nor are they in anyway responsible for any loss or damage resulting from the use (or misuse) of this publication.
Preface About this Manual This manual is intended for service personnel who have completed sufficient training to undertake the maintenance and inspection of personal computers. It is organized to allow you to look up basic information for servicing and/or upgrading components of the A110EU series LCD PC. The following information is included: Chapter 1, Introduction, provides general information about the location of system elements and their specifications.
Preface FCC Statement (Federal Communications Commission) You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Preface FCC RF Radiation Exposure Statement: 1. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. Warning Use only shielded cables to connect I/O devices to this equipment.
Preface Instructions for Care and Operation Removal Warning When removing any cover(s) and screw(s) for the purposes of device upgrade, remember to replace the cover(s) and screw(s) before restoring power to the system. Preface Also note the following when the cover is removed: • • Hazardous moving parts. Keep away from moving fan blades The notebook computer is quite rugged, but it can be damaged. To prevent this, follow these suggestions: 1. 2. 3. 4. 5. Don’t drop it, or expose it to shock.
Preface Cleaning Do not apply cleaner directly to the computer, use a soft clean cloth. Do not use volatile (petroleum distillates) or abrasive cleaners on any part of the computer. Servicing Do not attempt to service the computer yourself. Doing so may violate your warranty and expose you and the computer to electric shock. Refer all servicing to authorized service personnel. Unplug the computer from the power supply.
Preface Related Documents You may also need to consult the following manual for additional information: User’s Manual on CD This describes the computer’s features and the procedures for operating the computer and its ROM-based setup program. It also describes the installation and operation of the utility programs provided with the computer. System Startup Preface 1. Remove all packing materials, CDs/DVDs and floppy disks etc. 2. Securely attach any peripherals you want to use with the computer (e.g.
Preface Contents Notice ............................................................................................. 1-II About this Manual .........................................................................1-III FCC Statement ..............................................................................1-IV FCC RF Radiation Exposure Statement: ........................................ 1-V Cleaning ......................................................................................
Preface Preface PCH Power ................................................................................... B-18 PCH Power ................................................................................... B-19 PCH GND .................................................................................... B-20 LVDS, Inverter ............................................................................. B-21 SCALAR ......................................................................................
Introduction Chapter 1: Introduction Overview This manual covers the information you need to service or upgrade the A110EU series LCD computer. Information about operating the computer (e.g. getting started, and the Setup utility) is in the User’s Manual. Information about drivers (e.g. VGA & audio) is also found in User’s Manual. That manual is shipped with the computer. Operating systems (e.g. Windows 7, etc.) have their own manuals as do application software (e.g. word processing and database programs).
Introduction Specifications Latest Specification Information 1.Introduction The specifications listed here are correct at the time of sending them to the press. Certain items (particularly processor types/speeds) may be changed, delayed or updated due to the manufacturer's release schedule. Check with your service center for more details. CPU The CPU is not a user serviceable part. Accessing the CPU in any way may violate your warranty.
Introduction Interface Power Four USB 2.0 Ports Full Range AC/DC Adapter Two USB 3.0 Ports One HDMI-In Port One HDMI-Out Port One Headphone-Out Jack One Microphone-In Jack Two RS232 Serial (COM) Ports Two PS/2 Ports One RJ-45 LAN Jack One DC-in Jack AC Input: 100 - 240V, 50 - 60Hz DC Output: 19V, 6.
Introduction Tilting the LCD Screen & Adjusting the Height It is possible to tilt the LCD screen in order to get the best possible viewing angle of the screen without glare etc. 1.Introduction Moving the Computer We strongly recommend using both hands to move the computer. You can use one hand to grip the computer by the stand, and the other to hold the top of the LCD screen.
Introduction External Locator - Front View Figure 2 Front View 2 3 1 4 10 11 9 7 8 7 8 5 6 6 5 External Locator - Front View 1 - 5 1.Introduction 10 1. PC Camera (Optional) 2. PC Camera LED 3. Built-In Microphone 4. LCD (With Optional Touch Panel) 5. Power Button 6. Function Buttons 7. Power & System Activity LED Indicators 8.
Introduction Figure 3 External Locator - Left & Right Side Views 1.Introduction Left & Right Side Views 1. Stand 2. Multi-in-1 Card Reader 3. ExpressCard Slot /54(34) 4. 2 * USB 3.0 Port 5. HDMI-In Port 6. HDMI-Out Port 7. Emergency Eject Hole 8. Optical Device Drive Bay 9. Headphone-Out Jack 10. Microphone-In Jack 11. USB 2.0 Port 12. Stand ExpressCard Slot The ExpressCard Slot accepts either ExpressCard/34 or ExpressCard/54 formats.
Introduction External Locator - Rear View Figure 4 Rear View 1 Overheating 3 2 7 5 4 6 11 5 12 13 5 8 8 9 10 USB Port for Wireless Transceiver Note that the USB port for the wireless transceiver is designed specifically for the optional RF Keyboard & Mouse kit supplied with this model only. Do not use any other USB devices in this port. External Locator - Rear View 1 - 7 1.
Introduction Figure 5 Mainboard Overview - Top (Key Parts) Mainboard Top Key Parts 1.Introduction 1. ExpressCard/34/ 54 Slot 2. TUSB7320 3. TSUMU88ADT3 4. KBC-ITE IT8518 5.
Introduction Mainboard Overview - Bottom (Key Parts) Figure 6 Mainboard Bottom Key Parts 3 4 2 5 Mainboard Overview - Bottom (Key Parts) 1 - 9 1.Introduction 1 1. CPU Socket (CPU uninstalled) 2. Memory Slots DDR3 SO-DIMM 3. Mini-Card Connector (WLAN Module) 4. Coin Battery 5.
Introduction Figure 7 Mainboard Overview - Top (Connector) Mainboard Top Connector 1.Introduction 1.
Introduction Mainboard Overview - Bottom (Connectors) Figure 8 21 Mainboard Bottom Connectors 23 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 22 20 19 1 18 1 17 16 12. 13. 14. 15. 16. 17. 18. 19. 20. 15 2 21. 3 22. 23. 14 13 9 11 12 9 8 7 10 6 5 4 Mainboard Overview - Bottom (Connectors) 1 - 11 1.Introduction 11. USB 3.0 Ports HDMI-In Port HDMI-Out Port RJ-45 Lan Jack USB 3.
1.
Disassembly Chapter 2: Disassembly Overview This chapter provides step-by-step instructions for disassembling the A110EU series LCD computer’s parts and subsystems. When it comes to reassembly, reverse the procedures (unless otherwise indicated). We suggest you completely review any procedure before you take the computer apart. Warning Information 2.
Disassembly NOTE: All disassembly procedures assume that the system is turned OFF, and disconnected from any power supply. Maintenance Tools The following tools are recommended when working on the notebook PC: 2.Disassembly • • • • • • M3 Philips-head screwdriver M2.
Disassembly Maintenance Precautions The following precautions are a reminder. To avoid personal injury or damage to the computer while performing a removal and/or replacement job, take the following precautions: Power Safety Warning Before you undertake any upgrade procedures, make sure that you have turned off the power, and disconnected all peripherals and cables (including telephone lines).
Disassembly Disassembly Steps The following table lists the disassembly steps, and on which page to find the related information. PLEASE PERFORM THE DISASSEMBLY STEPS IN THE ORDER INDICATED. To remove the Battery: 1. Remove the battery 2. Install the battery To remove the WLAN Module: page 2 - 5 page 2 - 6 To remove the Rear Top Cover: 2.Disassembly 1. Remove the rear top cover page 2 - 7 page 2 - 7 page 2 - 8 To remove the Optical Device: 1. Remove the rear top cover 2.
Disassembly Removing and Installing the Battery Figure 1 Battery Removal Battery Removal Procedure 1. 2. 3. 4. Turn the computer off, remove the AC/DC adapter. Access the rear of the computer. Slide the latch 1 in the direction of the arrow (Figure 1a). Slide the latch 2 in the direction of the arrow, and hold it in place (Figure 1a). Slide the cover in the direction of the arrow until the bottom marker of the battery cover icon 3 is aligned with the marker on the side of the computer 4 (Figure 1a). 5.
Disassembly Figure 2 Battery Installation Procedure 1. Insert the battery 61 at an angle and slide it firmly into the battery bay until connected (Figure 2a). 2. Insert the battery bay cover 62 by angling it to fit on the right 3 at first, and then click the left side into place 4 (Figure 2b). a. Insert the battery. b. Insert the battery bay 3. Slide the cover in the direction of the arrow 5 until the top marker of the battery cover icon 6 is aligned with the cover.
Disassembly Removing the Rear Top Cover Figure 3 Before undertaking any upgrade procedure it is necessary to remove the rear top cover to access the components. 1. Turn off the computer and disconnect all cables and peripherals. 2. Carefully place the computer flat with the LCD facing down (make sure you cover the LCD to avoid scratches) so that you may access the rear cover. 3. Remove screws A & B (Figure 3a). 4.
Disassembly Figure 4 3.5” HDD Removal a. Locate the hard disk assembly b. Remove the screws. c. Slide the hard disk in the direction of the arrows. Removing the Hard Disk Drive The hard disk drive can be taken out to accommodate other 2.5" serial (SATA) hard disk drives with a height of 9.5mm (h). Follow your operating system’s installation instructions, and install all necessary drivers and utilities (as outlined in Chapter 4 of the User’s Manual) when setting up a new hard disk.
Disassembly 5. 6. 7. 8. Lift the hard disk assembly 76 out of the computer (Figure 5d). Remove screws 8 - 13 from the hard disk bracket (Figure 5e). Remove the left and right side brackets 14 from the HDD 15 . Reverse the process to install a new hard disk. Figure 5 3.5” HDD Removal (cont’d.) d. Remove the hard disk assembly. e. Remove the screws e. d. 8 10 7 14 14 9 12 13 2.Disassembly 11 15 7. Hard Disk Assembly 14. Side Brackets 15.
Disassembly Figure 6 2.5” HDD or SSD Removal 1. Remove the battery (page 2 - 5) and rear top cover (page 2 - 7). 2. The hard disk is located at point 1 (Figure 7a). 3. Remove screws 2 & 3 from the bracket (make sure you use a small manual screwdriver and not an electrical screwdriver to do this, due to the delicate nature of the screws). 4. Lift the HDD assembly 46 out of the computer. b. a. 2.Disassembly a. Locate the hard disk assembly b. Remove the screws. c.
Disassembly Removing the 2.5" (63.5mm) HDD from the Bracket 5. Remove screws 5 & 6 and separate the bracket 76 from the HDD 86 . 6. Reverse the process to install a new hard disk. Figure 7 2.5” HDD Removal d. Remove the screws and separate the bracket from the HDD d. 8 6 7 2.Disassembly 5 7.
Disassembly Figure 8 SSD Removal d. Remove the screws and separate the bracket from the HDD e. Separate the bracket and sponge Removing the SDD from the Bracket 5. Remove screws 5 & 6 and separate the bracket and sponge assembly 7 from the HDD 86 . 6. Separate the bracket 96 from the sponge 10 (Figure 4e). 7. Make sure you insert the sponge when installing a new HDD. 8. Reverse the process to install a new hard disk. d. e. 10 8 2.Disassembly 6 7 9 5 8. Hard Disk 9. Bracket 10.
Disassembly Removing the Optical (CD/DVD) Device Figure 9 Optical Device Module Removal 1. Remove the battery (page 2 - 5) and rear top cover (page 2 - 7). 2. Remove screw A from the optical device (Figure 9a). 6 out in the direction of arrow C (Figure 9b). 3. Push the optical device B a. a. Remove the screw. b. Push out the optical device module. b. C B 2.Disassembly A B.
Disassembly Figure 10 RAM Module Removal 2.Disassembly a. Locate the RAM. b. Pull the latches to release the RAM module. c. Remove the RAM module. Single Memory Module Installation If your computer has a single memory module, then insert the module into the Channel 0 (JDIMM_1) socket. In this case this is the upper memory socket (the socket furthest from the mainboard) as shown in Figure 10b.
Disassembly 5. Pull the latches to release the second module if necessary. 6. Insert a new module holding it at about a 30° angle and fit the connectors firmly into the memory slot. 7. The module’s pin alignment will allow it to only fit one way. Make sure the module is seated as far into the slot as it will go. DO NOT FORCE the module; it should fit without much pressure. 8. Press the module in and down towards the mainboard until the slot levers click into place to secure the module. 9.
Disassembly Figure 11 Stand Removal a. Push to release the stand cover. b. Remove the screws c. Remove the stand. Removing the Stand 1. Turn off the computer and disconnect all cables and peripherals. 2. Carefully place the computer flat with the LCD facing down (make sure you cover the LCD to avoid scratches) so that you may access the rear cover. 3. Push at point A to release the stand cover in the direction of the arrow B (Figure 11a).
Disassembly Removing the Wireless LAN Module Figure 12 1. 2. 3. 4. Remove the rear top cover (page 2 - 7). The WLAN module is located at point A (Figure 12a). Remove screw B , and disconnect antenna cables C & D (Figure 12b). When the screw and cables have been removed/disconnected the WLAN module E6 will pop up (Figure 12c) and can be removed (Figure 12d). a. b. A D C B WLAN Module Module Removal a. Locate the WLAN module. b. Remove the screw and disconnect the antenna cables. c.
Disassembly Figure 13 CPU Removal a. Locate the heat sink. b. Loosen the screws in the order indicated. c. Remove the heat sink unit. Removing the CPU 1. 2. 3. 4. Remove the rear top cover (page 2 - 7). The CPU heat sink unit is located at point A (Figure 13a). Loosen the heat sink unit screws in the order 4 , 3 , 2 , 1 (Figure 13b). 6 (Figure 13c). You can then remove the heat sink unit B a. b. 2.Disassembly A c.
Disassembly 5. 6. 7. 8. 9. Press down and hold the latch C (with the latch held down, you will be able to release it) (Figure 14d). Move the latch D and bracket E fully in the direction indicated to unlock the CPU. Carefully (it may be hot) lift the CPU F6 up out of the socket (Figure 14e). See page 2 - 20 for information on inserting a new CPU. When inserting a CPU, pay careful attention to the pin alignment, it will fit only one way (DO NOT FORCE IT!). e. d. CPU Removal (cont’d) d.
Disassembly Figure 15 Processor Installation 6 , paying careful attention to the pin alignment, it will fit only one way (DO NOT FORCE IT!) 1. Insert the CPU A (Figure 15a). 2. Press the bracket B and latch C to lock it. 3. Apply the thermal grease D to top of the CPU (Figure 15b). 4. Insert the heat sink E6 as indicated (Figure 15c). 5. Tighten screws in the order 1 , 2 , 3 , 4 (Figure 15d). b. a. 2.Disassembly a. Insert and lock in the CPU. b. Apply thermal grease to top of the CPU. c.
Part Lists Appendix A: Part Lists This appendix breaks down the A110EU series LCD computer’s construction into a series of illustrations. The component part numbers are indicated in the tables opposite the drawings. Note: This section indicates the manufacturer’s part numbers. Your organization may use a different system, so be sure to cross-check any relevant documentation. Note: Some assemblies may have parts in common (especially screws).
Part Lists Part List Illustration Location The following table indicates where to find the appropriate part list illustration. Table A- 1 A.
Part Lists Front Figure A - 1 Front A - 3 A.
Part Lists Front (No CCD) A.
Part Lists MB Figure A - 3 A.
Part Lists Back A.
Part Lists HDD Figure A - 5 HDD A - 7 A.
Part Lists DVD A.
Part Lists Combo Figure A - 7 擴孔 Combo A - 9 A.
A.
Schematic Diagrams Appendix B: Schematic Diagrams This appendix has circuit diagrams of the A110EU series LCD computer’s PCBs. The following table indicates where to find the appropriate schematic diagram. Diagram - Page Diagram - Page Diagram - Page Table B - 1 System Block Diagram - Page B - 2 PCH Power - Page B - 18 WLAN/TPM1.2/CCD/TP - Page B - 34 Processor 1/7 - Page B - 3 PCH Power - Page B - 19 5VS, 3VS, 1.5VS_CPU, 12V - Page B - 35 Processor 2/7 - Page B - 4 PCH GND - Page B - 20 3.
Schematic Diagrams System Block Diagram CLEVO A110EU AIO System Block Diagram Sandy Bridge / Ivy Bridge Processor LCD pannel 21.5'' FHD1920 x 1080 65W LGA1155 Socket 14.318 MHz HDMI IN CON. B.Schematic Diagrams LCD Controller 800/1067/1333 MHz SO-DIMM0 DDRIII DDR3 / 1.5V 5V,3.3V,5VS,3.3VS, 1.05VS,VDD12 3.3V_M,1.05V_M,1.05VS_VTT 1.05VS,12VS VDD3,VDD5 800/1067/1333 MHz SO-DIMM1 DDRIII DDR3 / 1.5V 1.8VS,0.85VS 1.5V,VTT_MEM,1.
Schematic Diagrams Processor 1/7 DMI,FDI SKT_H2 U1C 24.
Schematic Diagrams Processor 2/7 DDR A CHANNEL B.
Schematic Diagrams Processor 3/7 DDR B CHANNEL U1B 10 M_B_DQ[63:0] 10 M_B_DQS#[7:0] AG7 AG8 AJ9 AJ8 AG5 AG6 AJ6 AJ7 AL7 AM7 AM10 AL10 AL6 AM6 AL9 AM9 AP7 AR7 AP10 AR10 AP6 AR6 AP9 AR9 AM12 AM13 AR13 AP13 AL12 AL13 AR12 AP12 AR28 AR29 AL28 AL29 AP28 AP29 AM28 AM29 AP32 AP31 AP35 AP34 AR32 AR31 AR35 AR34 AM32 AM31 AL35 AL32 AM34 AL31 AM35 AL34 AH35 AH34 AE34 AE35 AJ35 AJ34 AF33 AF35 M_B_DQS0 M_B_DQS1 M_B_DQS2 M_B_DQS3 M_B_DQS4 M_B_DQS5 M_B_DQS6 M_B_DQS7 AH7 AM8 AR8 AN13 AN29 AP33 AL33 AG35 M_B_DQS#0 M_B
Schematic Diagrams Processor 4/7 MISC 1.05VS R17 10K_04 0.85VS SKT_H2 U1E 1.5V W2 W1 16 CLK_EXP_P 16 CLK_EXP_N R306 40 H_CPU_SVIDCLK 40 H_CPU_SVIDDAT 40 H_CPUSVIDALRT# R27 0_04 R19 R37 H_CPU_SVIDALRT# R35 R36 *10mil_short *10mil_short 44.
Schematic Diagrams Processor 5/7 VCORE, VGFX_CORE PROCESSOR CORE POWER VCORE ICCMAX Maximum Processor 48 SV 22u_6.3V_X5R_08_E 22u_6.3V_X5R_08_E 22u_6.3V_X5R_08_E C378 C383 C390 C366 C365 *22u_6.3V_X5R_08 *22u_6.3V_X5R_08 C116 *22u_6.3V_X5R_08 C381 22u_6.3V_X5R_08_E C115 *22u_6.3V_X5R_08 C402 22u_6.3V_X5R_08_E C393 *22u_6.3V_X5R_08 22u_6.3V_X5R_08_E C100 22u_6.3V_X5R_08_E C61 22u_6.3V_X5R_08_E C94 22u_6.3V_X5R_08_E C89 22u_6.3V_X5R_08_E C85 VCORE 10u_6.3V_X5R_08_E 10u_6.
Schematic Diagrams Processor 6/7 VCCIO, VDDQ, VCCSA, VCCPL PROCESSOR UNCORE POWER SKT _H2 U1H B.Schematic Diagrams 1.05VS_VTT Sheet 7 of 45 Processor 6/7 8.5A 1.05VS_VTT R309 0_04 1.05VS_VCCP_F + C142 C399 C97 C65 C96 22u_6.3V_X5R_08_E 22u_6.3V_X5R_08_E 22u_6.3V_X5R_08_E 22u_6.3V_X5R_08_E C83 C88 C415 C416 22u_6.3V_X5R_08_E 22u_6.3V_X5R_08_E 22u_6.3V_X5R_08_E 22u_6.3V_X5R_08_E C382 C388 C392 C80 C395 22u_6.3V_X5R_08_E 22u_6.3V_X5R_08_E 22u_6.3V_X5R_08_E 22u_6.
Schematic Diagrams Processor 7/7 GND U1I VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS_NCTF VSS_NCTF U1K SKT_H2 REV = 4 BALLMAP_REV = 1.
Schematic Diagrams DDR3 SO-DIMM_0 SO-DIMM A CHANGE TO STANDARD 3 M_A_A[15:0] M_A_A0 M_A_A1 M_A_A2 M_A_A3 M_A_A4 M_A_A5 M_A_A6 M_A_A7 M_A_A8 M_A_A9 M_A_A10 M_A_A11 M_A_A12 M_A_A13 M_A_A14 M_A_A15 B.
Schematic Diagrams DDR3 SO-DIMM_1 SO-DIMM B CHANGE TO STANDARD JDIMM2B 4 M_B_B[15:0] Layout Note: signal/space /signal: 8/4/8 109 108 79 114 121 101 103 102 104 73 74 115 110 113 197 201 202 200 4 M_B_BS0 4 M_B_BS1 4 M_B_BS2 4 M_B_CS#0 4 M_B_CS#1 4 M_B_CLK_DDR0 4 M_B_CLK_DDR#0 4 M_B_CLK_DDR1 4 M_B_CLK_DDR#1 4 M_B_CKE0 4 M_B_CKE1 4 M_B_CAS# 4 M_B_RAS# 4 M_B_WE# 9 SA0_DIM1 9 SA1_DIM1 9,14 SMB_CLK_DDR 9,14 SMB_DAT_DDR 4 4 116 120 M_B_ODT0 M_B_ODT1 11 28 46 63 136 153 170 187 4 M_B_DQS[7:0] 4 M_B_DQ
Schematic Diagrams PCH PCI PCI ? 3.3VS RN3 8.2K_8P4R_04 4 5 3 6 2 7 1 8 B.Schematic Diagrams 4 3 2 1 RN11 16 CK_PCH_33M_FB 25 PME# R393 PCH_GP4 PCI_INT#C INT_PIRQE# GPIO50 3.3VS RN7 4 3 2 1 5 6 7 8 GPIO52 PCH_GP5 PCI_INT#D PCI_INT#B 8.
Schematic Diagrams PCH USB/PCIE/DMI DMI , PCIE , USB USB_P0_DN USB_P0_DP 1.05VS R101 R115 R116 30 30 30 30 32 PCIE_RXN4_TI 32 PCIE_RXP4_TI 32 PCIE_TXN4_TI 32 PCIE_TXP4_TI 33 PCIE_RXN5_WLAN 33 PCIE_RXP5_WLAN 33 PCIE_TXN5_WLAN 33 PCIE_TXP5_WLAN 29 PCIE_RXN6_IGLAN 29 PCIE_RXP6_IGLAN 29 PCIE_TXN6_IGLAN 29 PCIE_TXP6_IGLAN 10K_04 10K_04 Z1201 CK_100M_DMI_PCH_DN CK_100M_DMI_PCH_DP C403 C406 0.1u_10V_X7R_04 0.1u_10V_X7R_04 PCIE_TXN1_C PCIE_TXP1_C C350 C349 0.1u_10V_X7R_04 0.
Schematic Diagrams PCH SATA SATA ? PPT_CRB PCH_GPIO17 BT17 BR19 BA22 BR16 BU16 BM18 BN17 BP15 PCH_GPIO6 SCI# PCH_GPIO68 PCH_GPIO69 PCH_GPIO70 PCH_GPIO71 PCH_GPIO69 PCH_GPIO17 PCH_GPIO70 PCH_GPIO68 10K_04 10K_04 10K_04 10K_04 20K_04 BC43 PCH_GPIO22 PCH_GPIO38 PCH_GPIO39 PCH_GPIO48 BA53 BE54 BF55 AW53 APWROK PWM0 PWM1 PWM2 PWM3 AY20 PCH_AY20 R344 R408 R419 C242 SATA2RXN SATA2RXP SATA2TXN SATA2TXP SATA3RXN SATA3RXP SATA3TXN SATA3TXP SATA4RXN SATA4RXP SATA4TXN SATA4TXP SATA5RXN SATA5RXP SATA5TXN
Schematic Diagrams PCH GPIO/HDA BIOS ROM SPI_* = 1.5"~6.5" R336 3.3K_1%_04 SPI_HOLD# 7 CE# SCK HOLD# VSS SPI_SO 1 6 R180 3.
Schematic Diagrams PCH NVRAM/HDMI HDMI ? PPT_CRB U2F R EV 1.
Schematic Diagrams PCH FDI/USB3/Clock USB3.0 , FDI , CLK ? U 2H PPT_CRB R EV 1.0 AT11 25 PCLK_KBC R383 22_04 C LK_PC I_KBC_R AN14 11 CK_PC H_33M_FB R161 22_04 C K_P_33M_PC I2 AT12 33 PCLK_TPM R388 22_04 C LK_PC I_TPM AT17 AT9 BA5 AW5 BA2 1.05VS R370 90.
Schematic Diagrams PCH Power POWER ? 1.05VS C195 C208 10u_6.3V_X5R_06_E 1u_6.3V_X5R_04 B.Schematic Diagrams PPT_CRB U2I 4.57A C201 C229 1u_6.3V_X5R_04 1u_6.3V_X5R_04 F20 F30 V25 V27 V31 V33 Y24 Y26 Y30 Y32 Y34 AA34 AA36 C202 Sheet 17 of 45 PCH Power V22 Y20 Y22 1u_6.3V_X5R_04 REV 1.0 VCCIO_24 VCCIO_25 VCCIO_26 VCCIO_27 VCCIO_28 VCCIO_29 VCCIO_30 VCCIO_31 VCCIO_32 VCCIO_33 VCCIO_34 1.
Schematic Diagrams PCH Power POWER 5VS_PCH_VCC5REFSUS D 12 3.3VS 5VS R B751S-40C 2 C A R407 1mA 10_1%_04 C503 D3 A VDD3 VDD5 1u_6.3V_X5R_04 5VA_PC H_VCC 5R EFSUS RB751S-40C2 C R203 U2K BF1 1mA 12mA 0.02A 5VA_PC H_VC C5R EFSU S 10_1%_04 C252 3.3A_1.5A_H DA_IO 0.1u_10V_X5R _04 3.3VS C228 C 473 0.1u_10V_X7R_04 *1u_6.3V_X5R_04 BT25 AV28 AU20 AV20 AU22 AN52 V5REF_SUS VCC VRM_1 VCC VRM_4 VCC VRM_3 VCC VRM_2 VCCSUSHD A VCC3_3_9 VCC3_3_10 VCC3_3_7 VC CPNAND_01 VC CPNAND_02 VCCSPI 3.
BC15 BC20 BC27 BC31 BC36 BC38 BC47 BC9 BD25 BD33 BF12 BF20 BF25 BF33 BF41 BF43 BF46 BF52 BF6 BG22 BG25 BG27 BG31 BG33 BG36 BG38 BH52 BH6 BJ1 BJ15 BK20 BK41 BK52 BK6 BM10 BM12 BM16 BM22 BM23 BM26 BM28 BM32 BM40 BM42 BM48 BM5 BN31 BN47 BN6 BP3 BP33 BP35 BR22 BR52 BU19 BU26 BU29 BU36 BU39 C19 C32 C39 C4 D15 D23 D3 D35 D43 D45 E19 E39 E54 E6 E9 F10 F12 F16 F22 F26 F32 F33 F35 F36 F40 F42 F46 F48 F50 F8 AV18 AV22 AV34 AV38 AV47 AV6 AW57 AY38 AY6 B23 BA11 BA12 BA31 BA41 BA44 G54 H15 H20 H22 H25 H27 H33 H6 J1 J33
Schematic Diagrams LVDS, Inverter PANEL CONNECTOR PANEL ID SELECTOR LVDSUN1 21 LVDSUP1 21 LVDSUN2 21 LVDSUP2 21 VDD3 C54 *10u_10V_Y 5V_08 8 7 6 5 ON 1 2 3 4 87216-3006 *0_06 SW_LCDID1 5 4 6 3 7 2 8 1 *10p_50V_NPO_04 *10p_50V_NPO_04 *10p_50V_NPO_04 *10p_50V_NPO_04 *10p_50V_NPO_04 *10p_50V_NPO_04 R7 PLVDD RN1 10K_8P4R_04 LVDSUN3 21 LVDSUP3 21 *0_04 LCDID1 *0_04 LCDID0 R10 R9 C13 DE_OUT SELLVDS 1 2 3 4 LVDSUCLKN 21 LVDSUCLKP 21 LCDID_2 LCDID_1 LCDID_0 R49 R63 R64 1K_04 1K_04 1K_04 LCDID1
Schematic Diagrams SCALAR ADC33 VDDC R519 3.3K_1%_04 R520 3.
Schematic Diagrams SCALAR-1 V DD3 -n²¾¾aªñPIN6¸} PC69 PC67 1.8V PC66 1u_25V_Y 5V_08 10K_04 Z2201 VDD5 PR70 10K_04 Z2202 8 1 PC68 1u_25V_Y 5V_08 VIN VIN POK VCNTL VOU T VOU T 3A 4 PR 75 1.27K_1%_04 3 EN GN D VFB 1.8 6 2 Z2203 PC 72 82p_50V_NPO_04 PR72 1K_1%_04 AX6615ESA 0.1u_16V_Y5V_04 PR71 PU4 VDD3 SC_1.8V 1 PJ9 L6 HCB1608KF-121T25 ADC33 . 2 C249 C260 C261 C248 C246 0.1u_16V_Y 5V_04 0.1u_16V_Y 5V_04 0.1u_16V_Y 5V_04 C467 0.1u_16V_Y 5V_04 C480 0.
Schematic Diagrams HDMI IN, USB2.
Schematic Diagrams HDMI OUT HDMI CONNECTOR ( W/ LEVELSHIFT,CO-LAY) A C A C A C534 R610 D9 BAV99N3 AC D8 BAV99N3 AC 2.2K_04 AC 2.2K_04 1 TMDS_CLOCK#-I D7 BAV99N3 TMDS_CLOCK-I 22u_6.3V_X5R_08_E C J_HDMI_OUT1 1_04 C267 22u_6.
Schematic Diagrams KBC-ITE IT8518 KBC_AVDD HCB1005KF-121T20 C286 C287 0.1u_16V_Y5V_04 0.1u_16V_Y 5V_04 0.1u_16V_Y5V_04 0.1u_16V_Y 5V_04 NEAR EC PIN C549 L32 HCB1005KF-121T20 . Sheet 25 of 45 KBC-ITE IT8518 13 13 C544 23 15 SMI# SCI# 0.
Schematic Diagrams Audio Codec ALC269 ALC269 AUDIO CODEC EMI Require ALC269 VB 5VS 2 *HCB1005KF-121T20 R543 *10mil_short *10mil_short C616 0.1u_16V_Y 5V_04 C292 0.1u_16V_Y 5V_04 C602 10u_10V_Y 5V_08_E R252 C613 *10u_10V_Y5V_08 0.1u_16V_Y 5V_04 ANALOG C301 0.1u_16V_Y 5V_04 C562 C300 10u_10V_Y 5V_08_E 40 41 44 45 R266 100K_04 47 48 EAPD_MODE 2 3 6 33_04 AZ_SDIN0_R 8 R253 33_04 AZ_SY NC_R 10 R251 33_04 HDA_RST#R 11 1u_6.
Schematic Diagrams AMP2607 & Audio Switch AUDIO AMP Low mute! AMP_PWR *0_04 VDD3 R547 0_04 3.3VS R290 Z2702 6 0.1u_10V_X5R_04 Z2703 7 FRONT-L C315 0.
Schematic Diagrams Card Reader / RTS5229 LENGTH <2INCH 3.3V_IN SD_WP/MS_BS SD_CD# MS_INS# 3.3VS R567 5,14,33 PLTRST# 14 CR_CLKREQ# CR1_LEDN *28mil_06 R598 10K_04 J_CARD_NOR1 | CLK - DATA | <= 100mils 40 mil | DATA.x - DATA.y | <= 100mils CLK NEED DOUBLE SPACE THEN OTHER 3.3V_IN SD_WP/MS_BS SD_CD# SD_D1 SD_D0/MS_D1 50ohm +/- 15% 24 23 22 21 20 19 R48 100ohm +/- 15% 0.1u_10V_X7R_04 HSOP 0.1u_10V_X7R_04 HSON RTS5229 QFN24 GND VCC_CARD *0.
Schematic Diagrams LAN (Intel LAN82579) LAN 82579V VDD 3 10K_04 41 42 12 PCIE_TXP6_IGLAN 12 PC IE_TXN6_IGLAN 14,30 SML0_CLK 14,30 SML0_DATA VDD 3 14 PM_LANPHY _EN R279 R281 *20mil_04_SH ORT *20mil_04_SH ORT R544 10K_04 R545 R268 *20mil_04_SH ORT *10K_04 Z2902 28 Z2903 31 Z2904 3 R282 R283 LAN_JTAG_TDI LAN_JTAG_TDO LAN_JTAG_TMS LAN_JTAG_TCK *10K_04 *10K_04 3.3V_M C 309 0.1u_16V_Y 5V_04 0.
Schematic Diagrams LAN CON/New Card R485 *0_04 WCM2012F2S-161T03 4 3 LAN PORT 1 2 L15 R487 *0_04 R490 *0_04 L16 4 L26 3.3V_M 29 29 29 29 LAN_MDIP0 LAN_MDIN0 LAN_MDIP1 LAN_MDIN1 29 29 29 29 LAN_MDIP2 LAN_MDIN2 LAN_MDIP3 LAN_MDIN3 LAN_MDIP0 LAN_MDIN0 LAN_MDIP1 LAN_MDIN1 12 11 9 8 LAN_MDIP2 LAN_MDIN2 LAN_MDIP3 LAN_MDIN3 6 5 3 2 R550 *0_04 C605 C603 C604 0.
Schematic Diagrams HDD/ODD/ESATA Closed to U2 3.3VS *0.01u_16V_X7R_04 GND 3.3VS D1 X 0 X 0 Low Power mode Function 1 1 0 CH0 -> 2.5 dB CH1 -> 0 dB 1 0 1 CH0 -> 0 dB CH1 -> 2.5 dB 1 1 1 CH0 & CH1 ->2. 5 dB Pre-emphasis. Normal SATA Output(Default state) HOST DEVICE TX_1N TX_1P RX_1N RX_1P SATARXN5 SATARXP5 *0.01u_16V_X7R_04SATATXP5R 1 *0.01u_16V_X7R_04SATATXN5R 2 SATARXN5 C662 SATARXP5 C663 *0.01u_16V_X7R_04SATARXN5R 4 *0.
Schematic Diagrams USB3.0 3.3V_USB3 L1 HCB1608KF-121T25 . t n e n o p m 5o 7C 3.3V_USB3 3VA 1.1V . VSS_1 VSS_2 B15 A17 U3TX1# U3TX1 B33 A36 PWRON1# USB_OC#1 A13 B12 U2DM2 U2DP2 USBVCC3.0_1 *10K_04 USB_OC#2 U3TX2# U3TX2 B34 A37 PWRON2# USB_OC#2 Z3204 5 U5 6 2 VIN1 VOUT2 7 C119 C120 8 0.1u_16V_Y5V_04 *0.1u_16V_Y5V_04 VIN2 VOUT3 R73 0_04 R74 *0_04 Z3205 4 EN# 1 GND C138 2A/90mohm 10u_10V_Y5V_08_E C121 220u_6.3V_6.3*6.3*4.2 USBVCC3.
Schematic Diagrams WLAN/TPM1.2/CCD/TP MINI CARD for WLAN& DEBUG CARD 5V USB PORT FOR TOUCH PANEL J_TP2 C676 *0_04 R52 10K_04 1 3 5 7 11 13 9 15 14 WLAN_CLKREQ# 16 CLK_PCIE_MINI# 16 CLK_PCIE_MINI WAKE# BT_DATA BT_CHCLK 3.3V_0 1.
Schematic Diagrams 5VS, 3VS, 1.5VS_CPU, 12V VDD3 VIN VA VIN1 VIN VA VIN1 PR196 C622 *0.1u_50V_Y 5V_06 *0.1u_50V_Y5V_06 1 2 31 PR96 M_BTN# Z3501 1K_04 3 4 PU12 VA VIN1 VIN DD_ON_LATCH M_BTN# PWR_SW# INSTANT-ON GND 100K_04 8 PR205 100K_04 DD_ON DD_ON# 7 DDON_LATCH 6 C621 0.1u_50V_Y5V_06 PQ70A 6 PWR_SW#_R 5 PR207 10K_04 PR206 1K_04 VDD3 25,37 DD_ON# D DD_ON *0.
Schematic Diagrams 3.3V_M, 1.05V_M, 1.05VS_VTT VDD5 VDD5 PR149 PR160 10K_04 10K_04 SLP_M PM_SLP_LAN PC149 MTN7002ZHS3 0.1u_16V_Y 5V_04 G 14 PM_SLP_LAN# PQ26A MTNN20N03Q8 8 2 7 1 10A NM OS PC157 PR161 0.1u_16V_Y 5V_04 100_04 MTN7002ZHS3 4 1M_04 PQ17 Z3601 G MTN7002ZHS3 *MTN7002ZHS3 D C442 2200p_50V_X7R_04 PR159 S PR148 0_04 *10K_04 D ON VDD3 SUSB PQ22 SUSB S G 34,38,39 1.05VS_VTT_EN 14 PQ57A MTDK5S6R G2 3.3V R329 *10K_04 VDD3 R326 10K_04 *MTN7002ZHS3 D 1.
Schematic Diagrams COM Port / PS2 3.3V R517 C1- /FORCEOFF 25 GND /INVALID 1 6 2 7 3 8 4 9 5 5VS_PS2 5VS_PS2 GND1 R531 10K_04 HCB1608KF-121T25 L36 K/B J_PS 2KB1 33_04 202AE09Y GPIGA3 25 PS2DAT0 25 PS2CLK0 Z3417 Z3418 1 2 3 4 5 6 L35 Z3419 Z3420 Z3421 33_04 C578 C601 C567 C611 TI/MAX3243CDBR C581 C614 C599 C574 R532 10K_04 C AC A RD8 BAV99N3 C AC A RD7 BAV99N3 For ESD .
Schematic Diagrams VDD3, VDD5 VREF_VDD PR175 *0_04 PR178 *20mil_04_SHORT PC173 1u_10V_Y 5V_06 VFB1 TONSEL VFB2 PR172 EN_3V PR184 EN_5V PC168 4 2 1 EN1 VFB1 3 VREF UGATE2 UGATE1 PHASE2 PHASE1 21 *10K_04 PC185 SYS5V PQ65 NTMFS4926N 0.1u_10V_X7R_04 G UGATE1 0.1u_50V_Y5V_06 VREF_VDD VREG5 PR171 PR169 *0_04 *20mil_04_SHORT PR173 *0_04 17 16 S C PR186 *0_04 *20mil_04_SHORT C C D PR76 *5.
Schematic Diagrams Power 0.925V/1.8VS -n²¾¾aªñPIN6¸} 1.8VS 5V 3 .3 V PC57 10K_04 1.8VS_PWRGD PR65 G VCNTL VOUT VOUT 6 VFB 2 PC61 0.1u_16V_Y5V_04 10u_6.3V_X5R_06_E VFB_6610 PR145 1.3K_1%_04 PC140 82p_50V_NPO_04 PR144 6-02-06615-320 6-02-07113-320 PJ5 2 *OPEN-3mm 0.1u_16V_Y 5V_04 PC60 1 3 EN GND 1.8VS 2A 4 AX6615ESA S 34,35,39 SUSB VIN VIN POK 1 PC54 PQ18 2SK3018S3 5 9 7 8 EN1.8VS1 100K_04 D 5V *10mil_short_04 POK_6610 R89 PC142 PC141 PC143 0.
Schematic Diagrams Power 1.5V/1.05VS 1 24 VTT VTT COMP PGOOD VDDQSNS S5 9 VDDQSET VDDQSET S3 Z3901 PC18 7 G5616 *1000p_50V_X7R_04 0.1u_50V_Y5V_06 2 3 1 4.7u_25V_X5R_08 5 6 7 8 PQ3 ME4626-G 4 PC2 PC3 S5_6163 10 PR42 *5.1_06 PC33 1.5V PC34 VDD3 PR31 PR 13 100K_04 *28mil_06 D DR1.5V_PWRGD DDR1.5V_PWRGD 14 PR28 VDD5 PR106 47K_04 PR103 100K_04 0.1u_16V_Y 5V_04 SU SC# 5G 4 S 14,25 VDD3 Z3908 1 PC8 10.7K_1%_04 R1 PQ1A MTDK5S6R PQ41 2SK3018S3 C 2.
Schematic Diagrams Power VCORE1 10p_50V_NPO_04 3.3VS Z4001 Z4002 Z4003 TRBSTA# *15mil_06 PR9 10K_04 PC108 2.2u_6.3V_X5R_04 Z4009 PR8 0_04 VR_EN PJ11 *6mil 1 2 H_CPU_SVIDDAT H_CPUSVIDALRT# H_CPU_SVIDCLK PR104 PR105 10K_04 95.3K_1%_04 VIN PR101 1K_04 3.3VS PC105 1 2 3 VR_RDY A 4 Z4010 H_CPU_SVIDDAT 5 H_CPUSVIDALRT# 6 H_CPU_SVIDCLK 7 8 VBOOT 9 Z4011 10 Z4012 11 H_PROCHOT# DELAY_PWRGD 12 13 14 15 Z4013 0.
Schematic Diagrams Power VCORE2 VIN DCR 1.1mohm 1 SW1 30A 2 40 CSREF 40 SWN1 40 G C D G 10_04 *15mil_04 2_06 PR117 G PD11 2200p_50V_X7R_04 CSREFA 40 PC134 PR118 10_04 *15mil_04 SWN1A 2200p_50V_X7R_04 Sheet 41 of 45 Power VCORE2 VIN HG2 40 SW2 S PC124 0.1u_50V_Y5V_06 15u_25V_6.3*4.4 D D G S G 40 + PQ45 *NTMFS4926N PC40 *4.7u_25V_X5R_08 PC37 PQ44 NTMFS4926N HG2 DCR 1.
Schematic Diagrams AC-In, Charger Z4203 16 BST_ 12 1 VAC C 10_06 VDDP_R 15 A MDL914S2 D PD9 *0_04 IACM 3 IACP 2 AC AV 9 HDR LDR ICHP BSTOZ8681-E ICHM VAC SDA VDDP SCL IACM IAC IACP COMP ACAV PU11 VDDA PC90 PC239 0.1u_50V_Y5V_06 PC238 4.7u_25V_X5R_08 4.7u_25V_X5R_08 0.
Schematic Diagrams Audio/USB Board E_USBVCC2.0 ÅܧóM-MSOP8¥]¸Ë 1 3 5 7 9 11 13 15 17 19 NC2 E_HP_SENSE E_MIC_SENSE E_HEADPHONE-R E_HEADPHONE-L E_MIC1-R E_MIC1-L E_AUDG 3 2 2 4 4 6 6 8 8 10 10 12 12 14 14 16 16 18 18 20 20 NC1 1 3 5 7 9 11 13 15 17 19 E_USB_P2_DN E_USB_P2_DP E_USB_P3_DN E_USB_P3_DP E_USB_P4_DN E_USB_P4_DP E_DD_ON# E_C13 E_C14 *0.1u_16V_Y5V_04 *0.1u_16V_Y5V_04 4 E_DD_ON# E_C18 10u_10V_Y5V_08_E For ESD E_GND FLG# VOUT1 VIN1 VOUT2 VIN2 VOUT3 EN# GND 7 8 1 SY6288DCAC 0.
Schematic Diagrams Power SW LED CIR Board POWER BOARD 1 3 SS_SW 1 TJG-533-S-T/R SS_J_PW1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 POWER SW POWER SW 2 4 SS_M_BTN# 5 6 SS_C2 0.1u_25V_X7R_06 SSGND SSGN D SS_3.
Schematic Diagrams Power Sequence VCCRTC 18ms RTCRST# VDD5 23ms VDD3 12V RSMRST# 91ms 102ms PM_SLP_LAN# 470us B.Schematic Diagrams 3.3V_M 2ms 1.05V_LAN_M Sheet 45 of 45 Power Sequence KBC_PWRBTN# SLP_S4# 16.4ms 36us SLP_S3# SLP_M# 1.5V (VDDQ) 1.05V_M PM_MPWROK 211us 356us 2ms 5VS 615us 3.3VS 733us 1.5VS 516us 1.8VS 1.05VS 1.05VS_VTT 0.85VS 7ms 984us 9.4ms 51ms ALL_SYS_PWRGD (VREN) VCORE PM_PCH_PWROK 51.2ms 290ms 4.67ms DELAY_PWRGD SYS_PWROK PLTRST# 1.89ms 3.
Wall Mounting Info Appendix C: Wall Mounting Guide The computer may be mounted on a wall for display, however in order to avoid personal injury or damage to the computer make note of the standards, warnings and precautions listed in this chapter: The system meets VESA (FDMI) Standard (100mm * 100mm), however before attaching any display bracket it is necessary to remove the stand. C.
Wall Mounting Info Figure 1 Stand Removal a. Push to release the stand cover. b. Remove the screws c. Remove the stand. Removing the Stand 1. Turn off the computer and disconnect all cables and peripherals. 2. Carefully place the computer flat with the LCD facing down (make sure you cover the LCD to avoid scratches) so that you may access the rear cover. 3. Push at point A to release the stand cover in the direction of the arrow B (Figure 1a).
Wall Mounting Info Mounting Systems This computer complies to the VESA FDMI (Flat Display Mounting Interface) 100mm * 100mm standard. Make sure that any mounting system you want to use meets the same standard. It is imperative that you consult appropriate professional installers (i.e. qualified engineering, construction or architectural personnel) to install, move or service any mounting system.
Wall Mounting Info General Guidelines for Wall Mounting • Only use professional installers to install, move or service any mounting system. • The system must only be mounted on a wall which can support the whole system’s weight (including the weight of any arm or bracket). • Make sure any wall is perpendicular and flat. • Any mounting system used must support a minimum of 30kg weight and be VESA compliant. C. Wall Mounting Info • Only use the screws and fittings supplied with the mounting system.
Wall Mounting Info Mounted System Example The following pictures show some examples of how a system can be mounted on to a wall. These pictures are intended for guideline purposes only, and are not specific instructions. Professional installers will determine the exact installation procedure for your specific bracket and mounting conditions. Installation Example 1.
Wall Mounting Info 3. The display can now be mounted by lowering the display bracket (in this example) over the wall bracket and attaching the screws. Note that this procedure usually requires two people, as one person will need to hold the computer while the other inserts and tightens the screws. C. Wall Mounting Info Figure 4 Mounting the Display 4. The cables may now be attached, and firmly secured, to the system’s ports and jacks.
BIOS Update Appendix D:Updating the FLASH ROM BIOS To update the FLASH ROM BIOS, you must: • • • • • • • Download the BIOS 1. Go to www.clevo.com.tw and point to E-Services and click E-Channel. 2. Use your user ID and password to access the appropriate download area (BIOS), and download the latest BIOS files (the BIOS file will be contained in a batch file that may be run directly once unzipped) for your computer model (see sidebar for important information on BIOS versions).
BIOS Update 5. Press F10 to save any changes you have made and exit the BIOS to restart the computer. Use the flash tools to update the BIOS 1. Make sure you are not loading any memory management programs such as HIMEM by holding the F8 key as you see the message “Starting MS-DOS”. You will then be prompted to give “Y” or “N” responses to the programs being loaded by DOS. Choose “N” for any memory management programs. 2. You should now be at the DOS prompt e.
