V10.1.
Preface Notice The company reserves the right to revise this publication or to change its contents without notice. Information contained herein is for reference only and does not constitute a commitment on the part of the manufacturer or any subsequent vendor. They assume no responsibility or liability for any errors or inaccuracies that may appear in this publication nor are they in anyway responsible for any loss or damage resulting from the use (or misuse) of this publication.
Preface R&TTE Directive This device is in compliance with the essential requirements and other relevant provisions of the R&TTE Directive 1999/5/EC. This device will be sold in the following EEA countries: Austria, Italy, Belgium, Liechtenstein, Denmark, Luxembourg, Finland, Netherlands, France, Norway, Germany, Portugal, Greece, Spain, Iceland, Sweden, Ireland, United Kingdom, Cyprus, Czech Republic, Estonia, Hungary, Latvia, Lithuania, Malta, Slovakia, Poland, Slovenia.
Preface FCC Statement (Federal Communications Commission) You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Preface FCC RF Radiation Exposure Statement: 1. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. Warning Use only shielded cables to connect I/O devices to this equipment.
Preface IMPORTANT SAFETY INSTRUCTIONS Follow basic safety precautions, including those listed below, to reduce the risk of fire, electric shock, and injury to persons when using any electrical equipment: 1. 2. 3. 4. 5. Do not use this product near water, for example near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool. Avoid using this equipment with a telephone line (other than a cordless type) during an electrical storm.
Preface Instructions for Care and Operation The computer is quite rugged, but it can be damaged. To prevent this, follow these suggestions: 1. Don’t drop it, or expose it to shock. If the computer falls, the case and the components could be damaged. 2. Keep it dry, and don’t overheat it. Keep the computer and power supply away from any kind of heating element. This is an electrical appliance. If water or any other liquid gets into it, the computer could be badly damaged. 3. Avoid interference.
Preface Power Safety The computer has specific power requirements: • When you want to unplug the power cord, be sure to disconnect it by the plug head, not by its wire. • Make sure the socket and any extension cord(s) you use can support the total current load of all the connected devices. • Before cleaning the computer, make sure it is disconnected from any external power supplies. Do not plug in the power cord if you are wet. Do not use the power cord if it is broken.
Preface Cleaning Do not apply cleaner directly to the computer, use a soft clean cloth. Do not use volatile (petroleum distillates) or abrasive cleaners on any part of the computer. Servicing Do not attempt to service the computer yourself. Doing so may violate your warranty and expose you and the computer to electric shock. Refer all servicing to authorized service personnel. Unplug the computer from the power supply.
Preface Ergonomics We designed your Multimedia PC system to be functional as well as attractive. To get most out of it, here are some suggestions on how to position and use the computer: • The top third of the LCD (screen) should be at eye-level or slightly below. • The LCD should be at least 18"/45cm. directly in front of you. • If the screen resolution makes you strain to read, then adjust the resolution to something more comfortable (see “Video Features” on page 1 - 15).
Preface Lighting Proper lighting and comfortable display viewing angle can reduce eye strain and muscle fatigue in your neck and shoulders. • • • • Position the display to avoid glare or reflections from overhead lighting or outside sources of light. Keep the display screen clean and set the brightness and contrast to levels that allow you to see the screen clearly. Position the display directly in front of you at a comfortable viewing distance. Adjust the display-viewing angle to find the best position.
Preface Wall Mounting Information The computer may be mounted on a wall for display. The system meets VESA (FDMI) Standard (100mm * 100mm) for wall mounting. However if you intend to wall mount the system please contact your service center for information in order to avoid personal injury, or damage to the computer.
Preface XII
Preface Contents Notice .................................................................................I FCC Statement ................................................................ III FCC RF Radiation Exposure Statement: ........................ IV Instructions for Care and Operation ............................... VI Power Safety ..................................................................VII Cleaning ....................................................................... VIII Servicing ......
Preface Power Management Overview ........................................................................3-1 Turning On the Computer ..............................................3-2 Power Plans ...................................................................3-3 Power-Saving States ......................................................3-5 Sleep ..............................................................................3-5 Hibernate ....................................................................
Preface Advanced Menu .............................................................5-8 Advanced Chipset Control (Advanced Menu) ..............5-8 Total Graphics Memory (Advanced Menu > Advanced Chipset Control) ...........................................5-9 SATA Mode (Advanced Menu) ....................................5-9 Legacy USB Support: (Advanced Menu) ......................5-9 Boot-time Diagnostic Screen (Advanced Menu) ...........5-9 Legacy OS Boot (Advanced Menu) ............................
Preface Upgrading and Adding New Hardware/Software ..........8-5 Problems & Possible Solutions ......................................8-7 Bluetooth Connection Problems ..................................8-10 Wake On LAN Setup ...................................................8-14 Interface (Ports & Jacks) Overview ....................................................................... A-1 Computer Ports and Jacks ............................................. A-2 Card Reader Port ............................
Preface Communication ............................................................. C-4 Power Management ...................................................... C-4 Power ............................................................................ C-4 Security ......................................................................... C-4 Operating System .......................................................... C-4 Environmental Spec ......................................................
Preface XVIII
Quick Start Guide Chapter 1: Quick Start Guide Overview This Quick Start Guide is a brief introduction to the basic features of your computer, to navigating around the computer and to getting your system started. The remainder of the manual covers the following: • Chapter 2 A guide to using some of the main features of the computer e.g. the storage devices (hard disk, optical device, Multi-in-1 card reader, ExpressCard/34/54) Audio & Printer. • Chapter 3 The computer’s power saving options.
1 Quick Start Guide Advanced Users If you are an advanced user you may skip over most of this Quick Start Guide. However you may find it useful to refer to “What to Install” on page 4 - 1, “BIOS Utilities” on page 5 - 1 and “Upgrading The Computer” on page 6 - 1 in the User’s Manual. You may also find the notes marked with a of interest to you. Notes Check the light colored boxes with the mark above to find detailed information about the computer’s features.
Quick Start Guide Not Included Operating Systems (e.g. Windows 7) and applications (e.g. word processing, spreadsheet and database programs) have their own manuals, so please consult the appropriate manuals. Drivers If you are installing new system software, or are re-configuring your computer for a different system, you will need to install the drivers listed in “Drivers & Utilities” on page 4 - 1. Drivers are programs which act as an interface between the computer and a hardware component e.g.
1 Quick Start Guide System Startup 1. 2. 3. 4. Remove all packing materials, CDs/DVDs and floppy disks etc. Securely attach any peripherals you want to use with the computer to their ports (e.g keyboard and mouse etc.) Attach the AC/DC adapter to the DC-In jack located under the LCD, then plug the AC power cord into an outlet, and connect the AC power cord to the AC/DC adapter. Push the power button at the front of the computer (under the LCD) to turn the computer “on”.
Quick Start Guide System Map: Front View 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 1 Optional Built-In PC Camera LCD (With Optional Touch Panel - see page 7 - 23) Power & System Activity LED Indicators Function Buttons* Power Button* USB 2.
1 Quick Start Guide Tilting the LCD Screen It is possible to tilt the LCD screen in order to get the best possible viewing angle of the screen without glare etc. Apply pressure with one hand at the base of the computer, while carefully pushing the LCD screen to tilt it to the appropriate viewing angle. 45° Moving the Computer We strongly recommend using both hands to move the computer. You can use one hand to grip the computer by the stand, and the other to hold the top of the LCD screen.
Quick Start Guide Keyboard Options There are two keyboard options for this computer series. These keyboards may include embedded numerical keypads for easy numeric data input and/or function keys/hot keys to allow you to change operational features instantly. Some keyboards may require a driver to access all available functions etc. Dongle & USB Ports A single USB dongle is provided with the keyboard, mouse and TV Tuner.
1 Quick Start Guide LED Indicators & Buttons The LED indicators on the computer display helpful information about the current status of the computer. The buttons located under the front panel icons allow you to make screen and input adjustments.
Quick Start Guide On Screen Display Indicators Visual indicators for brightness and volume are available when the OSD AP is installed (see “On Screen Display” on page 4 - 6). When the driver is installed, an icon will appear in the taskbar. Note that these indicators illustrate the volume and brightness level changes when adjusted by the buttons on the computer itself. Use the menu toggle button to switch between the brightness or volume (some keyboards may provide their own indicators).
1 Quick Start Guide Figure 1 - 6 Left View 1. 2. 3. 4. 5. 6. 7. Stand Multi-in-1 Card Reader ExpressCard Slot (see page 2 - 7) 1 * USB 3.0 Port HDMI-in Port Line-In Jack S/PDIF-Out Jack System Map: Left View HDMI-In Port Note that the HDMI-In Port supports video and audio signals from attached HDMI devices.
Quick Start Guide HDMI-In Port This computer features an HDMI (High-Definition Multimedia Interface) input port that allows you to display external sources such as Blu-ray players, DVDs, set top boxes and games consoles etc. on your computer screen. The computer itself does not need to be powered on to display video and audio from external sources.
1 Quick Start Guide System Map: Right View Figure 1 - 8 - Right View 1. 2. 3. Stand Optical Device Drive Bay (for CD/DVD Device - see page 2 - 3) Security Lock Slot CD Emergency Eject If you need to manually eject a CD/DVD (e.g. due to an unexpected power interruption) you may push the end of a straightened paper clip into the emergency eject hole. Do not use a sharpened pencil or similar object that may break and become lodged in the hole.
Quick Start Guide System Map: Rear View Figure 1 - 9 Rear View 3 1. 2. 2 CPU The CPU is not a user serviceable part. Opening this compartment, or accessing the CPU in any way, may violate your warranty. 3. 4. 5. Overheating 3 To prevent your computer from overheating make sure nothing blocks the Vent/Fan Intake while the computer is in use.
1 Quick Start Guide Windows 7 Start Menu & Control Panel Most of the control panels, utilities and programs within Windows 7 (and most other Windows versions) are accessed from the Start menu. When you install programs and utilities they will be installed on your hard disk drive, and a shortcut will usually be placed in the Start menu and/or the desktop. Right-click the Start menu icon , and then select Properties if you want to customize the appearance of the Start menu.
Quick Start Guide Video Features You can configure display options from the Display (Control Panel) and Screen Resolution in Windows. For more detailed video information see Chapter B“Video Driver Controls” from page B - 1. To access Display (Control Panel) and Screen Resolution in Windows: 1. 2. 3. Click Start and click Control Panel. Click Display (icon) - In the Appearance and Personalization category. Click Adjust Screen Resolution/Adjust resolution. Right-Click Desktop 1. 1 2. 2 3 3.
1 Quick Start Guide To access the Intel(R) Graphics Media Accelerator Driver for mobile control panel: 1. 2. Click Advanced settings 3 (Figure 1 - 11 on page 1 - 15) in the Screen Resolution control panel in Windows. Click the Intel(R)... tab and click Graphics Properties (button) 4 (Figure 1 - 12 on page 1 - 16) . OR 3. Right-click the desktop and select Graphics Properties from the menu. OR 4. Click the icon in the taskbar and select Graphics Properties from the menu.
Quick Start Guide Power Options The Power Options (Hardware and Sound menu) control panel icon in Windows (see page 1 - 14) allows you to configure power management features for your computer. You can conserve power by means of power plans and configure the options for the power button, sleep button, display and sleep mode from the left menu. Note that the power saver plan may have an affect on computer performance.
1 Quick Start Guide 1 - 18
Features & Components Chapter 2: Features & Components 2 Overview Read this chapter to learn more about the following main features and components of the computer: • • • • • • Hard Disk Drive Optical (CD/DVD) Device Multi-in-1 Card Reader ExpressCard Slot Audio Features Adding a Printer Overview 2 - 1
Features & Components 2 Power Safety Before attempting to access any of the internal components of your computer please ensure that the machine is not connected to the AC power, and that the machine is turned off. Also ensure that all peripheral cables, including phone lines, are disconnected from the computer. Hard Disk Drive The hard disk drive is used to store your data in the computer. The hard disk can be taken out to accommodate other 2.5" serial (SATA) hard disk drives with a height of 9.5 mm.
Features & Components Optical (CD/DVD) Device There is a bay for a 5.25" optical (CD/DVD) device (12.7mm height). The actual device will depend on the module you purchased (see “Storage” on page C - 3). The optical device is usually labeled “Drive D:” and may be used as a boot device if properly set in the BIOS (see “Boot Menu” on page 5 - 13).
Features & Components 2 Handling CDs or DVDs CD Emergency Eject If you need to manually eject a CD (e.g. due to an unexpected power interruption) you may push the end of a straightened paper clip into the emergency eject hole. However please do NOT use a sharpened pencil or similar object that may break and become lodged in the hole. Proper handling of your CDs/DVDs will prevent them from being damaged. Please follow the advice below to make sure that the data stored on your CDs/DVDs can be accessed.
Features & Components DVD Regional Codes To change the DVD regional codes: 1. 2. 3. Go to the Control Panel Double-click Device Manager (Hardware and Sound), then click the + next to DVD/CD-ROM drives. Double-click on the DVD-ROM device to bring up the Properties dialog box, and select the DVD Region (tab) to bring up the control panel to allow you to adjust the regional code.
Features & Components 2 Card Reader Cover Make sure you keep the cover in the card reader when not in use. This will help prevent foreign objects and/or dust getting in to the card reader. Multi-in-1 Card Reader The card reader allows you to use some of the latest digital storage cards. Push the card into the slot and it will appear as a removable device, and can be accessed in the same way as your hard disk (s).
Features & Components ExpressCard Slot The computer is equipped with an ExpressCard/34/54 slot that reads Express Card/ 34 and ExpressCard/54 formats. ExpressCards are the successors to PCMCIA (PC Cards). ExpressCard/54 is used for applications which require a larger interface slot, e.g. CompactFlash card reader. The number denotes the card width; 54mm for the Express Card/54 and 34mm for the ExpressCard/34. Make sure you install the Card Reader driver (see “ExpressCard/Card Reader” on page 4 - 6).
Features & Components 2 Sound Volume Adjustment The sound volume level is set using the volume control within Windows (and the volume function keys on the computer). Click the volume icon in the taskbar to check the setting. Audio Features You can configure the audio options on your computer from the Sound control panel in Windows, from the HD VDeck icon on the desktop or VIA HD Audio Deck control panel .
Features & Components Expert Mode will allow you to access more advanced configuration menus.
Features & Components 2 Parallel Printer After setting up the printer attach the parallel cable to the printer. Connect the printer’s parallel cable to the Parallel to USB converter, and then plug the converter into the USB port. Turn ON the printer, then turn ON the computer. Windows will identify the printer and either load one of its own drivers or ask you to supply one. Follow the on-screen instructions. Adding a Printer The most commonly used peripheral is a printer.
Power Management Chapter 3: Power Management Overview To conserve power, especially when using the battery, your computer power management conserves power by controlling individual components of the computer (the monitor and hard disk drive) or the whole system.
Power Management 3 Forced Off If the system “hangs”, and the Ctrl + Alt + Del key combination doesn’t work, press the power button for 4 seconds, or longer, to force the system to turn itself off. Power Button as Stand by or Hibernate Button You can use the OS’s “Power Options” control panel to set the power button to send the system into Stand by or Hibernate mode (see your OS’s documentation, or “Configuring the Power Buttons” on page 3 - 7 for details).
Power Management Power Plans The computer can be configured to conserve power by means of power plans. You can use (or modify) an existing power plan, or create a new one. The settings may be adjusted to set the display to turn off after a specified time, and to send the computer into Sleep after a period of inactivity. Click Change plan settings and then click Change advanced power settings to access further configuration options in Advanced Settings.
Power Management Each Windows power plan will also adjust the processor performance of your machine in order to save power. This is worth bearing in mind if you are experiencing any reduced performance (especially under DC/battery power). 3 Choose High performance (you may need to click Show additional plans to view the High performance plan) for maximum performance when the computer is powered from an AC power source.
Power Management Power-Saving States You can use power-saving states to stop the computer’s operation and restart where you left off. Win 7 uses the Sleep, Hibernate and Shut Down power-saving states. Sleep In Sleep all of your work, settings and preferences are saved to memory before the system sleeps. When you are not using your computer for a certain length of time, which you specify in the operating system, it will enter Sleep to save power.
Power Management Hibernate Hibernate uses the least amount of power of all the power-saving states and saves all of your information on a part of the hard disk before it turns the system off. If a power failure occurs the system can restore your work from the hard disk; if a power failure occurs when work is saved only to memory, then the work will be lost. Hibernate will also return you to where you last left off within seconds.
Power Management Configuring the Power Buttons The power button may be set to send the computer in to either Sleep or Hibernate. In Sleep, the LED will blink green. In Hibernate the LED will be orange. If only the display is turned off, the LED will remain green. Click Choose what the power buttons do on the left menu in Power Options to bring up the menu. Password Protection It is recommended that you enable a password on wake up in order to protect your data.
Power Management Resuming Operation You can resume operation from power-saving states by pressing the power button, or in some cases pressing the sleep button (see your keyboard documentation).
Drivers & Utilities Chapter 4: Drivers & Utilities This chapter deals with installing the drivers and utilities essential to the operation or improvement of some of the computer’s subsystems. The system takes advantage of some newer hardware components for which the latest versions of most available operating systems haven’t built in drivers and utilities. Thus, some of the system components won’t be auto-configured with an appropriate driver or utility during operating system installation.
Drivers & Utilities Driver Installation Insert the Device Drivers & Utilities + User’s Manual disc into the DVD drive and click Install Drivers/Option Drivers (button). 4 Follow the instructions to install the driver. Alternatively click Start, navigate (Browse..) to the executable file and then follow the manual setup instructions. 1. 2. 3.
Drivers & Utilities Driver for Windows 7 Page # Chipset Page 4 - 5 Video Page 4 - 5 LAN Page 4 - 5 ExpressCard/Card Reader Page 4 - 6 On Screen Display Page 4 - 6 USB 3.
Drivers & Utilities 4 Updating/Reinstalling Individual Drivers User Account Control If you wish to update/reinstall individual drivers it may be necessary to uninstall the original driver.To do this go to the Control Panel in the Windows OS and double-click the Programs and Features icon (Programs > Uninstall a program). Click to select the driver (if it is not listed see below) and click Uninstall, and then follow the on screen prompts (it may be necessary to restart the computer).
Drivers & Utilities New Hardware Found Driver Installation Procedure If you see the message “New Hardware Found” during the installation procedure (other than when outlined in the driver install procedure), click Cancel to close the window, and follow the installation procedure. Insert the Device Drivers & Utilities + User’s Manual disc into your DVD drive and click Install Drivers (button).
Drivers & Utilities ExpressCard/Card Reader 1. Click 4.Install Cardreader Driver > Yes. 2. Click Install > Finish. 4 On Screen Display 1. Click 5.Install OSD AP > Yes. 2. Click Next > Next. 3. Click Finish > Finish to restart the computer. USB 3.0 1. Click 6.Install USB 3.0 Driver > Yes. 2. Click Next. 3. Click the button to accept the license and then click Next. 4. Click Next > Install. 5. Click Finish. Intel MEI Driver 1. Click 7.Install MEI Driver > Yes. 2. Click Next > Yes > Next > Next. 3.
Drivers & Utilities Windows Experience Index After the drivers are installed follow this procedure to ensure an accurate rating from the Windows Experience Index: 1. Click Start, and click Control Panel. 2. Click Performance Information and Tools (System and Security > System > Check the Windows Experience Index). 3. Click “Rate this computer”. 4. The computer will take a few minutes to assess the system performance. 5. Close the control panel.
Drivers & Utilities 4 Optional Drivers PC Camera Module See the pages indicated for the driver installation procedures for any modules included in your purchase option. Insert the Device Drivers & Utilities + User’s Manual disc and click Option Drivers (button) to access the optional driver menu. See the introduction in “PC Camera Module” on page 7 - 2, and check the installation procedure.
BIOS Utilities Chapter 5: BIOS Utilities Overview This chapter gives a brief introduction to the computer’s built-in software: Diagnostics: The POST (Power-On Self Test) Configuration: The Phoenix SecureCore Setup Utility If your computer has never been set up, or you are making important changes to the system (e.g. hard disk setup), then you should review this chapter first and note the original settings found in Setup.
BIOS Utilities POST Screen 5 1.BIOS information 2.CPU type 3.Memory status 4.Enter Setup prompt appears only during POST The Power-On Self Test (POST) Each time you turn on the computer, the system takes a few seconds to conduct a POST, including a quick test of the on-board RAM (memory). As the POST proceeds, the computer will tell you if there is anything wrong. If there is a problem that prevents the system from booting, it will display a system summary and prompt you to run Setup.
BIOS Utilities Failing the POST Errors can be detected during the POST. There are two categories, “fatal” and “nonfatal”. Fatal Errors These stop the boot process and usually indicate there is something seriously wrong with your system. Take the computer to your service representative or authorized service center as soon as possible. Non-Fatal Errors This kind of error still allows you to boot.
BIOS Utilities BIOS Settings Warning 5 Incorrect settings can cause your system to malfunction. To correct mistakes, return to Setup and restore the Setup Defaults with . The Setup Utility The Phoenix SecureCore Setup Utility tells the system how to configure itself and manage basic features and subsystems (e.g. port configuration). Entering Setup To enter Setup, turn on the computer and press F2 during the POST.
BIOS Utilities Setup Screens The following pages contain additional advice on portions of the Setup. Setup Menus Along the top of the screen is a menu bar with menu headings. When you select a heading, a new screen appears. Scroll through the features listed on each screen to make changes to Setup. Instructions on how to navigate each screen are in the box along the bottom of the screen.
BIOS Utilities Main Menu Figure 5 - 2 Main Menu 5 System Time & Date (Main Menu) The hour setting uses the 24-hour system (i.e., ØØ = midnight; 13 = 1 pm). If you can change the date and time settings in your operating system, you will also change these settings. Some applications may also alter data files to reflect these changes.
BIOS Utilities SATA Port 1/2/3/4 (Main Menu) Pressing Enter opens the sub-menu to show the configuration of a optical Device/ HDD on the computer’s SATA Ports. Use the Auto (Type:) setting to have the items configured automatically for you. System/Extended Memory (Main Menu) This item contains information on the system memory, and is not user configurable. The system will auto detect the amount of memory installed.
BIOS Utilities Advanced Menu 5 Figure 5 - 3 Advanced Menu Advanced Chipset Control (Advanced Menu) The sub-menu here allows you to enable/disable the JMicron Power Saving (as used by the card reader) control, and to adjust the amount of Total Graphics Memory used by the system.
BIOS Utilities Total Graphics Memory (Advanced Menu > Advanced Chipset Control) Use this menu item to set the amount of system memory to be allocated for use by Intel® Dynamic Video Memory Technology for the graphics device. The default memory size allocated is MaxDVMT (up to 384MB) and this may be adjusted to 128MB or 256MB (by pressing the spacebar to adjust) if required (see “Dynamic Video Memory Technology” on page B - 1).
BIOS Utilities Legacy OS Boot (Advanced Menu) If “Enabled” the system will attempt to load the Legacy OS (e.g. Windows 7) first. If set to “Disabled” the system will attempt to EFI (Extensible Firmware Interface) boot before the Legacy OS. Power On Boot Beep (Advanced Menu) Use this menu item to enable/disable the beep as the computer starts up.
BIOS Utilities Security Menu Security Menu The changes you make here affect the access to the Setup utility itself, and also access to your machine as it boots up after you turn it on. These settings do not affect your machine or network passwords which will be set in your software OS. Set Supervisor Password (Security Menu) You can set a password for access to the Phoenix SecureCore Setup Utility. This will not affect access to the computer OS, (only the Phoenix SecureCore Setup Utility).
BIOS Utilities Password Warning 5 If you set a boot password (Password on boot is “Enabled“), NEVER forget your password. The consequences of this could be serious. If you cannot remember your boot password you must contact your vendor and you may lose all of the information on your hard disk. 5 - 12 Security Menu Set User Password (Security Menu) You can set a password for user mode access to the Phoenix SecureCore Setup Utility.
BIOS Utilities Boot Menu BIOS Screens Note that the BIOS screens pictured on these pages are intended for guidance in setting up your system’s BIOS. When you turn the computer on it will look for an operating system (e.g. Windows 7) from the devices listed in this menu, and in this priority order. If it cannot find the operating system on that device, it will try to load it from the next device in the order specified in the Boot priority order.
BIOS Utilities Exit Menu Figure 5 - 6 Exit Menu 5 Choosing to Discard Changes, or Exit Discarding Changes, will wipe out any changes you have made to the Setup. You can also choose to restore the original Setup defaults that will return the Setup to its original state, and erase any previous changes you have made in a previous session.
Upgrading The Computer Chapter 6: Upgrading The Computer Overview This chapter contains information on upgrading the computer. Follow the steps outlined to make the desired upgrades. If you have any trouble or problems you can contact your service representative for further help.
Upgrading The Computer When Not to Upgrade Power Safety Warning 6 Before you undertake any upgrade procedures, make sure that you have turned off the power, and disconnected all peripherals and cables (including telephone lines). These procedures involve opening the system’s case, adding and sometimes replacing parts.
Upgrading The Computer Removing the Rear Top Cover Before undertaking any upgrade procedure it is necessary to remove the rear top cover to access the components. 1. 2. 3. Turn off the computer and disconnect all cables and peripherals. Carefully place the computer flat with the LCD facing down (make sure you cover the LCD to avoid scratches) so that you may access the rear cover. Remove screws 1 - 4 .
Upgrading The Computer 4. Slide the rear top cover until the arrow is aligned with the unlock icon 5 . Figure 6 - 2 Rear Top Cover Unlock 5 6 5. When the arrow is aligned with the unlock icon you can remove the rear top cover 6 .
Upgrading The Computer Wireless Keyboard & Mouse USB Transceiver If your purchase includes an optional Wireless Keyboard & Mouse Kit you can use the USB port located behind the rear top cover to house the USB transceiver. 1. 2. 3. Remove the rear cover (see “Removing the Rear Top Cover” on page 6 - 3). Insert the USB transceiver 1 into the USB port 2 . Replace the rear top cover and screws. 1 2 Dongle & USB Ports A single USB dongle is provided with the keyboard, mouse and TV Tuner.
Upgrading The Computer HDD System Warning 6 New HDD’s are blank. Before you begin make sure: You have backed up any data you want to keep from your old HDD. You have all the CD-ROMs and FDDs required to install your operating system and programs. If you have access to the internet, download the latest application and hardware driver updates for the operating system you plan to install. Copy these to a removable medium.
Upgrading The Computer 3. Slide the hard disk in the direction of arrow 4 , and then slide it in the direction of arrow 5 to remove it. 5 Figure 6 - 6 4 Hard Disk Assembly Removal 6 4. Remove the adhesive hard disk cover 6 . 6 Figure 6 - 7 Hard Disk Cover Removal 5. Reverse the process to install a new hard disk.
Upgrading The Computer Contact Warning 6 Be careful not to touch the metal pins on the module’s connecting edge. Even the cleanest hands have oils which can attract particles, and degrade the module’s performance. Upgrading the System Memory (RAM) The computer has two memory sockets for 204 pin Small Outline Dual In-line (SODIMM) DDRIII (DDR3) type memory modules (see “Memory” on page C - 3 for details of supported module types).
Upgrading The Computer 3. Gently pull the two release latches on the sides of the memory socket in the direction indicated by the arrows ( 2 & 2 ) in Figure 6 - 9. 2 3 Figure 6 - 9 RAM Module Release 6 2 4. 5. 3 The RAM module will pop-up, and you can remove it. Pull the latches to release the second module if necessary.
Upgrading The Computer 6. Insert a new module holding it at about a 30° angle and fit the connectors firmly into the memory socket (see sidebar note if you are inserting a single module). Figure 6 - 10 RAM Module Removal 6 Single Memory Module Installation If your computer has a single memory module, then insert the module into the Channel 0 (JDIMM1) socket. In this case this is the upper memory socket (the socket furthest from the mainboard). 7.
Upgrading The Computer Upgrading the Processor If you want to upgrade your computer by replacing the existing processor with a faster/new one you will need to contact your customer service representative. We recommend that you do not do this yourself, since if it is done incorrectly you may damage the processor or mainboard. Warranty The CPU is not a user serviceable part. Accessing the CPU in any way, may violate your warranty. Unauthorized tampering with the HDD may also violate your warranty.
Upgrading The Computer 6 6 - 12
Modules & Options Chapter 7: Modules & Options Overview This chapter contains information on the following modules, which may come with your computer, depending on the configuration purchased. If you are unsure please contact your service representative.
Modules & Options PC Camera Screen Refresh 7 The PC Camera module supports a frame rate of 12 fps. If you find that the screen refresh rate is subject to lag or stuttering, then reduce the window size, or adjust the Output Size. To reduce Output Size run the camera application, click Options and select Video Capture Pin. Adjust the settings from the Output Size pull-down menu (see page 7 - 6). PC Camera Module There are a number of different camera modules available with this computer model series.
Modules & Options PC Camera Audio Setup If you wish to capture video & audio with your camera, it is necessary to connect a microphone to either of the microphone ports and then setup the audio recording options in Windows as follows. 1. 2. 3. 4. 5. 6. 7. 8. 9. Click Start, and click Control Panel (or point to Settings and click Control Panel). Click Sound (Hardware and Sound). Click Recording (tab). Right-click Microphone and make sure the item is not disabled.
Modules & Options Figure 7 - 1 Audio Setup for PC Camera Right-click 7 7 - 4 PC Camera Module
Modules & Options Camera Application The camera application is a video viewer for general purpose video viewing and testing, and for capturing video files to .avi format. 1. 2. 3. Run the camera application from the desktop shortcut (it is recommended that you set the capture file before the capture process - see Set Capture File below). Go to the Capture menu heading (if you wish to capture audio check “PC Camera Audio Setup” on page 7 - 3) and select Start Capture.
Modules & Options Reducing Video File Size Note that capturing high resolution video files requires a substantial amount of disk space for each file. After recording video, check the video file size (right-click the file and select Properties) and the remaining free space on your hard disk (go to My Computer, right-click the hard disk, and select Properties). If necessary you can remove the recorded video file to a removable medium e.g. CD, DVD or USB Flash drive.
Modules & Options Eliminating Screen Flicker If you find that the video screen in the camera application is flickering, you can try to adjust the setting in the Video Capture Filter options. 1. 2. 3. Run the camera application program from the desktop shortcut. Go to Options and scroll down to select Video Capture Filter.... Click either 50Hz or 60Hz under Powerline Frequency (Anti Flicker).
Modules & Options Snapshot Folder The Snapshot folder’s default location is on the desktop. Do not move this folder or an error may appear when you try to take a still picture. 7 Taking Still Pictures The camera application allows you to take still pictures. 1. 2. 3. If you accidentally delete or move the folder, you can create a new Snapshot folder on the desktop in order to capture the files. 7 - 8 PC Camera Module Run the camera application from the desktop shortcut.
Modules & Options Wireless LAN Module If you have included an 802.11b/g/n WLAN module in your purchase option, install the driver as per the procedure overleaf. Make sure you install the drivers in the order indicated in Table 4 - 1, on page 4 - 3. 802.11b/g/n Driver Installation 1. Insert the Device Drivers & Utilities + User’s Manual disc into the CD/ DVD drive. 2. Click Option Drivers (button). 3. Click 2.Install WLAN Driver > Yes. 4. Choose the language you prefer and click Next. 5.
Modules & Options Network and Sharing Center You can also use the Network and Sharing Center control panel in Windows (Network and Internet) to connect to any available wireless networks. Connecting to a Wireless Network in Windows 7 Make sure the Wireless LAN module is turned on. 1.
Modules & Options 2. 3. 4. You may need to enter a security key for any access point to which you are trying to connect. Click to select a network location (e.g. Home, Work or Public). Click “View or change settings in Network and Sharing Center” to access further options for the connection.
Modules & Options Security Enabled Networks 5. 6. Click the taskbar icon to see any currently connected networks. To disconnect from the wireless network you can click the taskbar wireless icon , click the active connection and then click Disconnect (button). You should try to make sure that any network you are connecting to is a secure network. 7 Connecting to unsecure networks may allow unauthorized access to your computer, documents, websites and files etc.
Modules & Options Windows Mobility Center The Windows Mobility Center control panel provides an easy point of access for information on display, audio, power plans used and wireless device status etc. To access the Windows Mobility Center: 1. 2. 3. Click Start, and click Control Panel (or point to Settings and click Control Panel). Double-click Windows Mobility Center (Hardware and Sound). Click the button to Turn wireless off/on, or click the icon to access the network menu.
Modules & Options Bluetooth & WLAN Combo Module If your purchase option includes the Combination Wireless LAN & V3.0 Bluetooth module then install the driver as instructed overleaf. Follow the instructions on page 7 - 20 to configure the Bluetooth settings. Bluetooth Data Transfer 7 Note that the transfer of data between the computer and a Bluetooth enabled device is supported in one direction only (simultaneous data transfer is not supported).
Modules & Options Bluetooth Combo Driver Installation 1. Insert the Device Drivers & Utilities + User’s Manual disc into the CD/ DVD drive. 2. Click Option Drivers (button). 3. Click 3.Install Combo BT Driver > Yes. 4. Choose the language you prefer and click OK. 5. Click Next. 6. Click the button to accept the license and click Next. 7. Click Next > (select if you want to create an icon to appear on the desktop) Next > Install. 8. Click Finish. 9.
Modules & Options Bluetooth & WLAN Combo Settings 1. 2. Double-click the My Bluetooth application on the desktop (or access it from the Programs/All Programs menu) Click My Bluetooth Settings (menu heading).
Modules & Options 3. 4. Click General Settings to change the computer name that other Bluetooth devices will see, and click the tickbox to Allow Bluetooth devices to find this computer Click OK to confirm the settings.
Modules & Options 5. 6. Click File Transfer Settings to Enable sharing of my files with other Bluetooth devices. Click OK to confirm the settings.
Modules & Options Bluetooth Networking Setup 1. 2. Double-click the My Bluetooth application on the desktop (or access it from the Programs/All Programs menu). Click My Bluetooth Settings (see Figure 7 - 7 on page 7 - 16). 7 Figure 7 - 10 Network Settings 3. 4. 5. Click Network Settings (make sure the Bluetooth module is powered on. Click Enable Bluetooth Network and click OK. A message will appear in the taskbar to confirm that the network driver has been installed.
Modules & Options Bluetooth & WLAN Combo Module Configuration Setup your Bluetooth Device so the Computer Can Find it 1. 2. Turn your Bluetooth device (e.g. PDA, mobile phone etc.) on. Make the device discoverable (to do this check your device documentation). To Add a Bluetooth Device 1. 2. Double-click the My Bluetooth application on the desktop (or access it from the Programs/All Programs menu).
Modules & Options 3. You will then be presented with a menu of options to select from. 7 Figure 7 - 12 Bluetooth Device Options 4. Click the appropriate button to connect to the device.
Modules & Options 5. 6. You may need to allow the connection from your device, and you will then need to provide a passcode from the device. You can then enter the passcode on the computer and click OK to establish the connection.
Modules & Options Touch Screen Module If you have included a Touch Screen module in your purchase option, you should obtain a stylus pen to interact with the computer in the same way you would use a mouse (use a stylus pen to tap/double-tap on-screen buttons etc.). Make sure you install the driver as indicated below. Touch Screen Driver Installation 1. Insert the Device Drivers & Utilities + User’s Manual disc into the CD/ DVD drive. 2. Click Option Drivers (button). 3. Click 4.
Modules & Options Tablet PC Options Tablet PC settings (for touch screen input) may be customized from the Tablet PC Settings in Windows 7. 1. 2. To access the control panel click Start, and then click Control Panel. The Tablet PC Settings and Pen and Touch control panel are in the Hardware and Sound category.
Modules & Options 3. 4. Click Tablet PC Settings and click Other. Click Go to Input Panel Settings (in Tablet PC Input Panel Options) to configure where and how the Tablet PC Input Panel appears.
Modules & Options 5. Click Go to Pen and Touch (in Tablet PC Input Panel Options) to configure the Pen Options, flicks and handwriting etc. 6. When not in use the Tablet PC Input Panel docks at the side of the screen (and may be docked at either side of the screen at any height) with just a small portion visible.
Modules & Options 7. 8. 9. Move the pen over the TIC and then tap it to activate it. The input panel allows you to input text without the use of a keyboard. You can use the writing pad (write continuously), character pad (write one character at a time) or touch keyboard to input text. Use Help topics from the Tools menu for further information.
Modules & Options TV Antenna The TV antenna supplied with any TV Tuner module is intended for indoor use only. Please do not use your TV Tuner module outdoors. TV Tuner Module The optional TV Tuner allows you to watch TV, play music CDs, video conference and capture still images and video on your PC. If your purchase configuration includes the optional Digital TV Tuner module, you will be supplied with a remote control unit and USB transceiver dongle for the module.
Modules & Options Windows Media Center 1. This TV Tuner module is fully supported by Windows Media Center in Windows 7 (not included in Starter or Home Basic versions). 2. Run Windows Media Center directly from the Start menu (Start > Programs > Windows Media Center). 3. Windows Help and Support provides information on the Windows Media Center functions. Click Start and select Help and Support, and then type “Media Center” in the Search Help box and click the magnifying glass icon to bring up the results.
Modules & Options TV Recording and Power Plans If you intend to use the optional TV Tuner to record live TV, then go to the Power Options control panel and create a power plan (see “Power Plans” on page 3 - 4) to prevent the power saving options from adjusting the computer’s performance level. Remote Control Unit 7 The remote control unit allows you to remotely start and send the system into a power saving state, to run Windows Media Center and to navigate the Media Center menus etc.
Troubleshooting Chapter 8: Troubleshooting Overview Should you have any problems with your computer, before consulting your service representative, you may want to try to solve the problem yourself. This chapter lists some common problems and their possible solutions. This can’t anticipate every problem, but you should check here before you panic. If you don’t find the answer in these pages, make sure you have followed the instructions carefully and observed the safety precautions in the preface.
Troubleshooting Basic Hints and Tips Many of the following may seem obvious but they are often the solution to a problem when your computer appears not to be working. • Power - Is the computer actually plugged into a working electrical outlet? If plugged into a power strip, make sure it is actually working. Check the LED Power & Communication Indicators (see “LED Indicators & Buttons” on page 1 - 8) to see the computer’s power status.
Troubleshooting Backup and General Maintenance • Always backup your important data, and keep copies of your OS and programs safe, but close to hand. Don’t forget to note the serial numbers if you are storing them out of their original cases, e.g. in a CD wallet. • Run maintenance programs on your hard disk and OS as often as you can. You may schedule these programs to run at times when you are not using your computer.
Troubleshooting Viruses • Install an Anti-Virus program and keep the definitions file (the file which tells your program which viruses to look for) up to date. New computer viruses are discovered daily, and some of them may seriously harm your computer and cause you to lose data. Anti-Virus programs are commercially available and the definitions file updates are usually downloadable directly from the internet. • Be careful when opening e-mail from sources you don’t know.
Troubleshooting Upgrading and Adding New Hardware/Software • Do not be tempted to make changes to your Windows Registry unless you are very sure of what you are doing, otherwise you will risk severely damaging your system. • Don’t open your computer or undertake any repair or upgrade work if you are not comfortable with what you are doing. • Read the documentation.
Troubleshooting • Thoroughly check any recent changes you made to your system as these changes may affect one or more system components, or software programs. If possible, go back and undo the change you just made and see if the problem still occurs. • Don’t over complicate things.
Troubleshooting Problems & Possible Solutions Problem Possible Cause - Solution The computer feels too hot. Make sure the computer is properly ventilated and the Vent/Fan intakes are not blocked. If this doesn’t cool it down, put the system into Hibernate mode or turn it off for an hour. Make sure the computer isn’t sitting on a thermal surface (see “Overheating” on page 1 - 13). Make sure you’re using the correct adapter. Nothing screen. The system is in a power saving mode.
Troubleshooting Problem Possible Cause - Solution The compact disc tray will not open when there is a disc in the tray. The compact disc is not correctly placed in the tray. Gently try to remove the disc using the eject hole (see “Loading Discs” on page 2 - 3). The DVD regional codes can no longer be changed. The code has been changed the maximum 5 times. See “DVD Regional Codes” on page 2 - 5. You forget password. If you forget the password, you may have to discharge the battery of the CMOS.
Troubleshooting Problem Possible Cause - Solution The Wireless LAN cannot connect to an access point. The WLAN module is turned off in the Windows Mobility Center. Make sure that Wireless is ON in the Mobility Center to ensure proper function key behavior (see “Windows Mobility Center” on page 7 - 13). My TV Tuner experiencing interference. The USB dongle is plugged into the USB port located behind the rear top cover (see Figure 6 - 4 on page 6 - 5) and this causes interference.
Troubleshooting Bluetooth Connection Problems If you are experiencing problems connecting to some Bluetooth devices (in particular certain mobile phones and headsets) it maybe necessary to download and install the Windows Mobile Device Center software (for Windows Vista and Windows 7). Go to the Microsoft website and search for the Microsoft Windows Device Center Driver for Windows Vista (64-bit or 32-bit) and Windows 7 (64-bit or 32-bit), and then download the driver. 1. 2. 3. 4. 5.
Troubleshooting 6. 7. 8. Right-click Bluetooth Peripheral Device and click on Update Driver Software. Click Browse my computer for driver software. Click Let Me pick from a list of device drivers on my computer. Figure 8 - 2 - Browse my computer.../Let me pick from... 9. Select Bluetooth Radios from the list.
Troubleshooting 10. A list of drivers will appear with Manufacturer on one side and Model in the other. 11. Choose Microsoft Corporation (make sure you choose the full name Microsoft Corporation and do not choose Microsoft - Note that you must have installed the Microsoft Windows Device Center Driver for Microsoft Corporation to appear in the list). 12. Select Windows Mobile-based device support from the Model list. 8 Make sure you select Microsoft Corporation Figure 8 - 4 - Select Device Driver 13.
Troubleshooting 15. The Device Manager should now display the Windows Mobile-based device support under Bluetooth Radios. 16. You will need to repeat the process for any other Bluetooth Peripheral Devices listed under Other Devices.
Troubleshooting Wake On LAN Setup Wake On LAN is an Ethernet computer networking standard that allows a computer to be turned on or woken up by a network message. If you need to have your computer Wake On LAN you will need to enable Computer Management settings as follows. 1. 2. 3. 4. 5. Go the Windows control panel and double-click Administrative Tools (System and Security). Double-click Computer Management. Click Device Manager under System Tools, and click the arrow to the left of Network adapters.
Troubleshooting 6. 7. Click Advanced (tab). Scroll down to the bottom of the Property menu and click to select each of the values listed below. Property Item Settings for Wake On LAN Set each of the following Property items to Enabled. Item: Setting: • Wake on Connect Enabled • Wake on Link Raised Enabled • Wake on Magic Packet Enabled • Wake on Pattern Match Enabled • Wakeup from Shutdown Enabled 8 Figure 8 - 7- Network Adapter Wake On LAN (Advanced) 8.
Troubleshooting 8 8 - 16
Interface (Ports & Jacks) Appendix A: Interface (Ports & Jacks) Overview The following chapter will give a quick description of the interface (ports & jacks) which allow your computer to communicate with external devices, connect to the internet etc.
Interface (Ports & Jacks) Computer Ports and Jacks Item Description Card Reader Port The card reader allows you to use some of the latest digital storage cards. Push the card into the slot and it will appear as a removable device. COM/Serial Ports The COM/serial is a communication interface for data transfer, through which information transfers in or out one bit at a time. This port can be used to connect the computer to devices such as terminals and peripherals.
Interface (Ports & Jacks) Item Description HDMI-In Port The HDMI-In (High-Definition Multimedia Interface) port allows you to display external sources such as Blu-ray players, DVDs, set top boxes and games consoles etc. on your computer screen as long as the computer’s AD/DC adapter is plugged in to a power source (see “HDMI-In Port” on page 1 - 11). Headphone-Out Jack Headphones or speakers may be connected through this jack.
Interface (Ports & Jacks) Item Description S/PDIF-Out Jack This S/PDIF (Sony/Philips Digital Interface Format) Out Jack allows you to connect your DVDcapable PC to a Dolby AC-3 compatible receiver for “5.1” or ‘dts’ surround sound. USB 2.0/1.1 Ports These USB (Universal Serial Bus) 2.0 compatible ports (USB 2.0 is fully USB 1.
Intel Video Driver Controls Appendix B: Intel Video Driver Controls The basic settings for configuring the LCD are outlined in “Video Features” on page 1 - 15. DVMT Notes Intel Video Driver Installation Make sure you install all the drivers in the order indicated in Table 4 - 1, on page 4 - 3. Video 1. Insert the Device Drivers & Utilities + User’s Manual disc into the CD/ DVD drive. 1. Click 2.Install VGA Driver > Yes. 2. Click Next > Yes > Next > Next. 3. Click Finish to restart the computer.
Intel Video Driver Controls HDMI-In Port This computer features an HDMI (High-Definition Multimedia Interface) input port that allows you to display external sources such as Blu-ray players, DVDs, set top boxes and games consoles etc. on your computer screen. B Intel® Graphics & Media Control Panel Advanced video configuration options are provided by the Intel® Graphics and Media Control Panel. To access the control panel: 1. 2.
Intel Video Driver Controls You may make changes to any of the graphics properties by clicking the appropriate menu tab on the left of the menu and adjusting the settings on the right. Options & Support Click Options & Support and select an item from the sub-menu to bring up the help and support topics. You will need to be connected to the Internet to access the key resource links. Multiple Display At least one other display must be attached in order to view multiple display selection options.
Intel Video Driver Controls Multiple Display At least one other display must be attached in order to view Multiple Display selection options. General Settings Attaching Other Displays If you prefer to use a monitor or flat panel display, connect it to the external monitor port. To Clone Displays: 1. 2. 3. 4. 5. Attach your display to the external monitor port and turn it on. Go to the Intel(R) G&M control panel and click Display > Multiple Displays.
Intel Video Driver Controls To Enable Extended Desktop: 1. 2. 3. 4. Attach your display to the external monitor port and turn it on. Go to the Intel(R) G&M control panel and click Display > Multiple Displays. Click Operating Mode and select Extended Desktop from the menu. Click Apply, and OK to confirm the settings change. Click the appropriate monitor icon and drag it to match the physical arrangement you wish to use (e.g. the secondary display may be extended left/right/above/below the primary display).
Intel Video Driver Controls Configuring an External Display in Windows 7 You can also use the Screen Resolution control panel in Windows 7 to configure an external display. 1. 2. 3. 4. Attach your display to the external monitor port and turn it on. Go to the Screen resolution control panel (see “Video Features - Win 7” on page 1 - 16). Click the Detect button. The computer will then detect any attached displays.
Intel Video Driver Controls 5. You can configure the displays from the Multiple Displays menu. Figure B - 6 Screen Resolution Multiple Display Options (Win 7) • Duplicate these displays - Shows an exact copy of the main display desktop on the other display(s). • Extend these displays - Treats both connected displays as separate devices. • Show desktop only on 1/2 - Only one of your displays is used.
Intel Video Driver Controls Using the Windows Logo Key + P Key Combination to Switch Displays You can also use the + P key combination to quickly change display configuration and modes (this is particularly useful when attaching a projector) in Windows 7. 1. 2. 3. 4. Attach your display to the external monitor port and turn it on. + P key combination. Press the An on-screen menu will pop up.
Specifications Appendix C: Specifications Latest Specification Information The specifications listed in this Appendix are correct at the time of going to press. Certain items (particularly processor types/ speeds and CD/DVD device types) may be changed or updated due to the manufacturer's release schedule. Check with your service center for details.
Specifications Processor Processor Processor Intel® Core i7 Mobile Processor: =============================== i7-640M (2.80GHz) 32nm (32 Nanometer) Process Technology, 4MB L3 Cache & FSB 1066MHz - TDP 35W rPGA988A Package Intel® Core i5 Mobile Processor: =============================== i5-450M (2.40GHz) 32nm (32 Nanometer) Process Technology, 3MB L3 Cache & FSB 1066MHz - TDP 35W rPGA988A Package =============================== Intel® Core™ i3 Mobile Processor: =============================== i3-350M (2.
Specifications Memory Storage Interface Dual Channel DDRIII (DDR3) Up to Two Changeable 2.5" 9.5 mm (h) SATA (Serial) Hard Disk Drives Four USB 2.0 Ports One USB 3.
Specifications Card Reader Communication Power Embedded Multi-In-1 Card Reader - MMC / RSMMC - SD / Mini SD / SDHC / SDXC Compatible - MS / MS Pro / MS Duo Built-In 10/100/100 Mb Base-TX Ethernet LAN Full Range AC/DC Adapter – AC in 100 240V, 50 - 60Hz DC Output 19V, 4.74A (90 Watts) Note: Some of these cards require PC adapters that are usually supplied with the cards. Combo WLAN (802.11b/g/n) and Bluetooth v3.
Specifications Physical Dimensions & Weight 450mm (w) * 312mm (d) * 66.
Specifications C C - 6 Specifications
