V13.3.
Preface Notice The company reserves the right to revise this publication or to change its contents without notice. Information contained herein is for reference only and does not constitute a commitment on the part of the manufacturer or any subsequent vendor. They assume no responsibility or liability for any errors or inaccuracies that may appear in this publication nor are they in anyway responsible for any loss or damage resulting from the use (or misuse) of this publication.
Preface R&TTE Directive This device is in compliance with the essential requirements and other relevant provisions of the R&TTE Directive 1999/5/EC. This device will be sold in the following EEA countries: Austria, Italy, Belgium, Liechtenstein, Denmark, Luxembourg, Finland, Netherlands, France, Norway, Germany, Portugal, Greece, Spain, Iceland, Sweden, Ireland, United Kingdom, Cyprus, Czech Republic, Estonia, Hungary, Latvia, Lithuania, Malta, Slovakia, Poland, Slovenia.
Preface CE Marking This device has been tested to and conforms to the regulatory requirements of the European Union and has attained CE Marking. The CE Mark is a conformity marking consisting of the letters “CE”. The CE Mark applies to products regulated by certain European health, safety and environmental protection legislation. The CE Mark is obligatory for products it applies to: the manufacturer affixes the marking in order to be allowed to sell his product in the European market.
Preface FCC Statement (Federal Communications Commission) You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Preface FCC RF Radiation Exposure Statement: 1. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. Warning Use only shielded cables to connect I/O devices to this equipment.
Preface IMPORTANT SAFETY INSTRUCTIONS Follow basic safety precautions, including those listed below, to reduce the risk of fire, electric shock, and injury to persons when using any electrical equipment: 1. 2. 3. 4. 5. Do not use this product near water, for example near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool. Avoid using this equipment with a telephone line (other than a cordless type) during an electrical storm.
Preface Instructions for Care and Operation The notebook computer is quite rugged, but it can be damaged. To prevent this, follow these suggestions: 1. Don’t drop it, or expose it to shock. If the computer falls, the case and the components could be damaged. Do not expose the computer to any shock or vibration. 2. Do not place it on an unstable surface. Do not place anything heavy on the computer. Keep it dry, and don’t overheat it.
Preface 3. Avoid interference. Keep the computer away from high capacity transformers, electric motors, and other strong magnetic fields. These can hinder proper performance and damage your data. 4. Follow the proper working procedures for the computer. Shut the computer down properly and don’t forget to save your work. Remember to periodically save your data as data may be lost if the battery is depleted. Do not turn off the power until you properly shut down all programs. 5.
Preface Power Safety The computer has specific power requirements: • Only use a power adapter approved for use with this computer. • Your AC/DC adapter may be designed for international travel but it still requires a steady, uninterrupted power supply. If you are unsure of your local power specifications, consult your service representative or local power company. • The power adapter may have either a 2-prong or a 3-prong grounded plug.
Preface Polymer Battery Precautions Note the following information which is specific to polymer batteries only, and where applicable, this overrides the general battery precaution information overleaf. • Polymer batteries may experience a slight expansion or swelling, however this is part of the battery’s safety mechanism and is not a cause for concern. • Use proper handling procedures when using polymer batteries.
Preface Battery Precautions • Only use batteries designed for this computer. The wrong battery type may explode, leak or damage the computer. • Do not remove any batteries from the computer while it is powered on. • Do not continue to use a battery that has been dropped, or that appears damaged (e.g. bent or twisted) in any way. Even if the computer continues to work with a damaged battery in place, it may cause circuit damage, which may possibly result in fire.
Preface Cleaning Do not apply cleaner directly to the computer; use a soft clean cloth. Do not use volatile (petroleum distillates) or abrasive cleaners on any part of the computer. Servicing Do not attempt to service the computer yourself. Doing so may violate your warranty and expose you and the computer to electric shock. Refer all servicing to authorized service personnel. Unplug the computer from the power supply.
Preface Travel Considerations Packing As you get ready for your trip, run through this list to make sure the system is ready to go: 1. 2. 3. 4. 5. 6. 7. 8. Check that the battery pack and any spares are fully charged. Power off the computer and peripherals. Close the display panel and make sure it’s latched. Disconnect the AC/DC adapter and cables. Stow them in the carrying bag. The AC/DC adapter uses voltages from 100 to 240 volts so you won’t need a second voltage adapter.
Preface On the Road In addition to the general safety and maintenance suggestions in this preface, and Chapter 8: Troubleshooting, keep these points in mind: Hand-carry the notebook - For security, don’t let it out of your sight. In some areas, computer theft is very common. Don’t check it with normal luggage. Baggage handlers may not be sufficiently careful. Avoid knocking the computer against hard objects.
Preface Developing Good Work Habits Developing good work habits is important if you need to work in front of the computer for long periods of time. Improper work habits can result in discomfort or serious injury from repetitive strain to your hands, wrists or other joints. The following are some tips to reduce the strain: • Adjust the height of the chair and/or desk so that the keyboard is at or slightly below the level of your elbow. Keep your forearms, wrists, and hands in a relaxed position.
Preface Lighting Proper lighting and comfortable display viewing angle can reduce eye strain and muscle fatigue in your neck and shoulders. • • • • Position the display to avoid glare or reflections from overhead lighting or outside sources of light. Keep the display screen clean and set the brightness and contrast to levels that allow you to see the screen clearly. Position the display directly in front of you at a comfortable viewing distance. Adjust the display-viewing angle to find the best position.
Preface Contents Notice .............................................................................................................................................................I ErP Off Mode Power Consumption Statement: ........................................................................................... II FCC Statement ............................................................................................................................................
Preface System Map: LCD Panel Open ..................................................................................................................1-6 LED Indicators ...........................................................................................................................................1-7 Keyboard ....................................................................................................................................................1-8 Keyboard Shortcuts .....................
Preface Features & Components Overview ....................................................................................................................................................2-1 Hard Disk Drive/Solid State Drive ............................................................................................................2-2 Multi-In-1 Push-Push Card Reader ...........................................................................................................2-3 Touchpad and Buttons/Mouse ...
Preface Configuring the Power Buttons .................................................................................................................3-8 Resuming Operation ................................................................................................................................3-10 Power Conservation Modes .....................................................................................................................3-11 Battery Information ......................................
Preface Video (VGA) .............................................................................................................................................4-7 LAN ...........................................................................................................................................................4-7 CardReader ................................................................................................................................................4-7 Touchpad ................
Preface MB Series / BIOS Revision / KBC/EC firmware Revision ......................................................................5-6 Advanced Menu .........................................................................................................................................5-7 Intel Smart Connect Technology (Advanced Menu) .................................................................................5-7 Intel(R) Rapid Start Technology (Advanced Menu) ..........................................
Preface Upgrading The Computer Overview ....................................................................................................................................................6-1 When Not to Upgrade ................................................................................................................................6-2 Removing the Battery ................................................................................................................................
Preface 3rd Party Bluetooth (V4.0) Combo Driver Installation ...........................................................................7-18 Intel Bluetooth Combo Driver Installation ..............................................................................................7-18 Bluetooth Configuration in Windows 8 ...................................................................................................7-19 Trusted Platform (Security) Module ......................................................
Preface 3G Configuration in Windows 8 ..............................................................................................................7-62 EM820W 3G Module PIN Code & Power-Saving ..................................................................................7-65 Troubleshooting Overview ....................................................................................................................................................8-1 Basic Hints and Tips ................................
Preface Display Devices & Options ....................................................................................................................C-15 Attaching Other Displays .......................................................................................................................C-16 Attaching Other Displays - Devices (Charms Bar) ................................................................................C-18 Configuring an External Display In Windows ................................
Preface BIOS .........................................................................................................................................................D-3 Security .....................................................................................................................................................D-3 Features .....................................................................................................................................................D-4 Operating System .
Preface XXVIII
Quick Start Guide Chapter 1: Quick Start Guide Overview This Quick Start Guide is a brief introduction to the basic features of your computer, to navigating around the computer and to getting your system started. The remainder of the manual covers the following: • Chapter 2 • Chapter 3 • Chapter 4 • Chapter 5 • Chapter 6 • Chapter 7 • Appendix A • Appendix B • Appendix C • Appendix D A guide to using some of the main features of the computer e.g.
1 Quick Start Guide Advanced Users If you are an advanced user you may skip over most of this Quick Start Guide. However you may find it useful to refer to “What to Install” on page 4 - 1, “BIOS Utilities” on page 5 - 1 and “Upgrading The Computer” on page 6 - 1 in the reminder of the User’s Manual. You may also find the notes marked with a of interest to you.
Quick Start Guide Not Included Operating Systems (e.g. Windows 8) and applications (e.g. word processing, spreadsheet and database programs) have their own manuals, so please consult the appropriate manuals. Drivers If you are installing new system software, or are re-configuring your computer for a different system, you will need to install the drivers listed in “Drivers & Utilities” on page 4 - 1. Drivers are programs which act as an interface between the computer and a hardware component e.g.
1 Quick Start Guide System Startup 1. 2. 3. 4. 5. Remove all packing materials. Place the computer on a stable surface. Securely attach any peripherals you want to use with the notebook (e.g. keyboard and mouse) to their ports. Attach the AC/DC adapter to the DC-In jack on the right of the computer, then plug the AC power cord into an outlet, and connect the AC power cord to the AC/DC adapter.
Quick Start Guide System Software Your computer may already come with system software pre-installed. Where this is not the case, or where you are re-configuring your computer for a different system, you will find the Windows 8 operating system is supported. Note: In order to run Windows 8 (64-bit) without limitations or decreased performance, your computer requires a minimum 2GB of system memory (RAM).
1 Quick Start Guide Figure 1 - 2 LCD Panel Open 1. 2. 3. 4. 5. 6. 7. System Map: LCD Panel Open 2 Built-in PC Camera PC Camera LED Built-In Microphone LCD Power Button Keyboard Touchpad & Buttons 1 3 Wireless Device Operation Aboard Aircraft 4 5 6 7 1 - 6 System Map: LCD Panel Open The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the WLAN/ Bluetooth module(s) are OFF if you are using the computer aboard aircraft.
Quick Start Guide LED Indicators The LED indicators on the computer display helpful information about the current status of the computer.
1 Quick Start Guide Other Keyboards If your keyboard is damaged or you just want to make a change, you can use any standard USB keyboard. The system will detect and enable it automatically. However special functions/hot-keys unique to the system’s regular keyboard may not work. Keyboard The keyboard has an embedded numerical keypad for easy numeric data input, and function keys to change operational features instantly.
Quick Start Guide Keyboard Shortcuts The following Windows Logo Key (Winkey) keyboard shortcuts are useful for navigation/operation in Windows 8.
1 Quick Start Guide Function/Hot Key Indicators The function keys (F1 - F12 etc.) will act as hot keys when pressed while the Fn key is held down. In addition to the basic function key combinations; visual indicators are available when the hot key utility is installed.
Quick Start Guide Control Center When in the Windows Desktop application (not in the Start screen) press the Fn + Esc key combination, or double-click the icon in the notification area of the taskbar to toggle the Control Center on/off. The Control Center gives quick access to frequently used controls and enables you to quickly turn the camera/Touch Pad on/off. Control Center Click on any button to turn any of the modules (e.g. TouchPad, Camera) on/off.
1 Quick Start Guide Figure 1 - 5 Front & Left Views 1. 2. 3. 4. 5. 6. LED Power Indicators Security Lock Slot Microphone-In Jack Headphone-Out Jack Vent/Fan Intake/ Outlet Speaker System Map: Front & Left Views 1 2 3 4 5 6 Overheating To prevent your computer from overheating make sure nothing blocks the Vent/Fan Intake while the computer is in use.
Quick Start Guide System Map: Right & Rear Views 1 3 2 7 Multi-In-1 Push-Push Card Reader The card reader allows you to use the most popular digital storage card formats: MMC (MultiMedia Card) / RS MMC SD (Secure Digital) / Mini SD / SDHC /W255EU SDXC Optical Device Drives To install applications and drivers etc. you will need to attach an external optical CD/DVD device to the USB ports. 3 Figure 1 - 6 Right & Rear Views 4 5 6 1. Speaker 2. Multi-in-1 PushPush Card Reader 3. USB 3.0 Port 4.
1 Quick Start Guide Figure 1 - 7 Bottom View 1. 2. 3. 4. 5. System Map: Bottom View 1 Battery Vent/Fan Intake/ Outlet Speakers Component Bay Cover HDD Bay Cover 4 2 Battery Information 2 2 3 5 2 3 Always completely discharge, then fully charge, a new battery before using it. Completely discharge and charge the battery at least once every 30 days or after about 20 partial discharges. CPU The CPU is not a user serviceable part.
Quick Start Guide 3G Module USIM Card Installation If you have included an optional 3G module, follow the instructions below to install the USIM card (which will be provided by your service provider). See page 7 - 62 for configuration instructions. 1. 2. 3. 4. 5. 6. Turn the computer off, remove the AC/DC adapter and turn it over. Slide the latch 1 in the direction of the arrow. Slide the latch 2 in the direction of the arrow, and hold it in place.
1 Quick Start Guide Windows 8 Touch Screen Controls/Gestures This computer model incorporates a touch screen and this can be used to navigate through he interface in much the same way as a mouse, touchpad and keyboard. Where you see the instruction to click an item in this manual, you can choose to tap/double tap the appropriate area of the screen instead. The following gestures are useful when navigating the Windows 8 interface.
Quick Start Guide • Swipe from left and back (Display running apps) - Slide your finger from the left and quickly drag it back towards the right to display a list of apps that are currently running. Tap any app to switch to it. • Pull down from the top (Close app) - Close any running app by starting at the top area of the screen and quickly pulling your finger about halfway down the screen.
1 Quick Start Guide Touch Keyboard If you need to type on screen then the Touch Keyboard will pop up when required (e.g. when you need to type in an internet URL address in Internet Explorer). When the Touch Keyboard is displayed you have several display/input options and these can be accessed from the icon at the bottom right of the keyboard. To access the Touch Keyboard from the Desktop app click/tap the keyboard icon in the taskbar .
Quick Start Guide The Touch Keyboard allows you to input text without the use of an actual keyboard., and you can use writing pad to write (continuously or one character at a time) or touch keyboard to input text. Use the Help menu for further information.
1 Quick Start Guide Windows Control Panel Throughout this manual you will see an instruction to open the Control Panel. In Windows 8 right-click the lower left hot corner to bring up the context menu (or use the Windows Logo Key + X key combination) and select Control Panel. Swipe a finger from the right of the Touchpad from the Desktop (not the Start screen) to access the Charms Bar, click Settings and click Control Panel.
Quick Start Guide Windows 8 Start Screen & Desktop The Apps, control panels, utilities and programs within Windows 8 are accessed from the Start screen and/or Windows Desktop app. The Desktop (which runs as an app within the Start screen) can be accessed by clicking the Desktop item in the Start screen (or by using the Windows Logo Key + D key combination).
1 Quick Start Guide Apps & Tiles The Windows 8 Start screen will contain a number of apps, and many more will be installed as you add more applications etc. Not all of these apps can fit on one screen so you will often need use the slider at the bottom of the screen in order to view all the necessary Apps. Accessing Pining/Unpinning All Apps You can add and remove the tiles for apps and control panels in the Start screen. Right-click on a blank area of the Start screen, and you will see the All Apps icon.
Quick Start Guide Desktop Application When the Desktop app is running (click the app in the Start screen or use the Windows Logo Key + D key combination) you can use lower left hot corner to switch between the Start screen and the Windows Desktop app. To do so move your mouse to hover over the bottom left corner of the screen and click the pop-up. When you move to the lower left hot corner in the Start screen itself it will take you back to your most recently used app.
1 Quick Start Guide Display Most Recently Used Apps When the Desktop app is running you can right-click the lower left hot corner (or use the Windows Logo Key + X key combination) to bring up an advanced context menu of useful features such as Control Panel, Programs and Features, Power Options, Task Manager, Search, Windows Explorer, Command Prompt, Device Manager and Network Connections etc.
Quick Start Guide Windows 8 Charms Bar The right side of the screen displays the Windows 8 Charms Bar. The Charms Bar contains the Search, Share, Start, Devices and Settings menus. To access up the Charms Bar move the cursor to the upper or lower right corners of the screen, and then hover over one of the items in the Charms Bar to activate it (the bar will be black when it is active), or use the Windows Logo Key + C key combination.
1 Quick Start Guide Charms Bar Items • Search results. • Share : You can search for any file, application, Apps and control panel settings with instantaneous : This button is used to share information with people via mail or social networks. • Start : Click to bring up the Start Menu (the same function as pressing the Windows Logo Key or clicking the bottom left of the screen). • Devices : Click this button to change connected peripheral device settings e.g. an external display.
Quick Start Guide Windows 8 Control Panel In many instances throughout this manual you will see an instruction to open the Control Panel. The Control Panel can be accessed in a number of ways in Windows 8. • Click/ Search in the Windows Charms Bar (see previous page) and the search pane will pop out. Type Control Panel and select it from the results to the left.
1 Quick Start Guide • When in the Desktop app (this does not apply to the Start screen) click on Settings in the Windows Charms Bar and select Control Panel from the menu. Figure 1 - 22 - Settings Charms Bar (Desktop App Only) • Right-click on a blank area of the Start screen, or swipe a finger from the top or bottom of the touch screen. Click the All Apps icon and click Control Panel.
Quick Start Guide • Right-click the lower left hot corner to bring up the menu and select Control Panel (see Figure 1 - 17 on page 1 - 24). Keyboard Shortcut to Control Panel You can also use keyboard shortcuts to access the Control Panel. Press the Windows logo key and X to bring up the context menu, and then press P to bring up the Control Panel. Alternatively press the Windows logo key and R to bring up the Run dialog box, and then type “Control Panel” and press Enter to access the Control Panel.
1 Quick Start Guide Windows 8 Taskbar In many instances throughout this manual you will see an instruction to access the notification area of the taskbar. In Windows 8 the taskbar is accessed from the Desktop application. If you are in the Start screen you will need to click the Desktop app to switch to the Desktop. The taskbar is displayed at the bottom of the desktop screen, and you can see the notification area of the taskbar in the bottom right of the screen.
Quick Start Guide Video Features You can switch display devices, and configure display options, from the Display control panel (in Appearances and Personalization) in Windows 8 when running the Desktop app (see “Desktop Application” on page 1 - 23 and Appendix C). In Windows 8 it is possible to quickly configure external displays from the Devices menu item in the Charms Bar (see “Windows 8 Charms Bar” on page 1 - 25). To Configure Displays from Devices (Charms Bar): 1. 2. 3. 4.
1 Quick Start Guide To access Display (Control Panel) and Screen Resolution in Windows 8: 1. 2. 3. Go to the Control Panel. Click Display (icon) - In the Appearance and Personalization category. Adjust resolution. Right-Click Desktop App 1. 2. 2 1 3 Figure 1 - 26 - Screen Resolution 1 - 32 Video Features 3. You can right-click the desktop and select Screen resolution 1 (Figure 1 - 26). Use the dropbox to select the screen Resolution 2 (Figure 1 - 26).
Quick Start Guide To access the Intel(R) HD Graphics Control Panel: 1. 2. Click Advanced settings 3 (Figure 1 - 26 on page 1 - 32) in the Screen Resolution control panel in Windows. Click the Intel(R)... tab and click Graphics Properties (button) 4 (Figure 1 - 27) . OR 3. Right-click the desktop and select Graphics Properties from the menu. OR 4. Click the icon in the notification area of the Desktop taskbar and select Graphics Properties from the menu.
1 Quick Start Guide Power Options Power Options (Hardware and Sound) can be accessed from the Control Panel. The Power Menu item in Settings in the Charms Bar in Windows 8 may be used to Shut down or Restart (you can also add Hibernate/ Sleep to the menu). Shut Down, Restart or Sleep 1. 2. 3. Go to the Charms Bar and click Settings. Click Power . Select Sleep, Shut Down or Restart.
Quick Start Guide Running Apps To run apps in Windows 8 you will need to check that the Screen Resolution and User Account Control Settings are compatible with the system requirements. Screen Resolution Settings 1. 2. Switch to the Windows Desktop (click the app or use the Windows logo key + D key combination). Right-click a blank area of the Windows Desktop and select Screen Resolution.
1 Quick Start Guide User Account Control Settings If your computer meets the minimum screen resolution requirements, and still you can't run Metro apps, then that you have to check the status of User Account Control (UAC). Metro apps may fail to open when the UAC is turned off. To check whether the UAC is on or off, follow the instructions below. 1. 2. 3. 4. Open the Control Panel.
Features & Components Chapter 2: Features & Components 2 Overview Read this chapter to learn more about the following main features and components of the computer: • • • • Hard Disk Drive/Solid State Drive Multi-In-1 Push-Push Card Reader Touchpad and Buttons/Mouse Audio Features Overview 2 - 1
Features & Components 2 Power Safety Before attempting to access any of the internal components of your computer please ensure that the machine is not connected to the AC power, and that the machine is turned off. Also ensure that all peripheral cables, including phone lines, are disconnected from the computer. Hard Disk Drive/Solid State Drive The hard disk/solid state drive is used to store your data in the computer.
Features & Components Multi-In-1 Push-Push Card Reader The card reader allows you to use some of the latest digital storage cards. Push the card into the slot and it will appear as a removable device, and can be accessed in the same way as your hard disk (s). Make sure you install the card reader driver (see “CardReader” on page 4 - 7. • MMC (MultiMedia Card) / RS MMC • SD (Secure Digital) / Mini SD / SDHC / SDXC Note: Some of these cards require PC adapters that are usually supplied with the cards.
Features & Components 2 Mouse Driver If you are using an external mouse your operating system may be able to auto-configure your mouse during its installation or only enable its basic functions. Be sure to check the device’s user documentation for details. Touchpad and Buttons/Mouse The Touchpad is an alternative to the mouse; however, you can also add a mouse to your computer through one of the USB ports. The Touchpad buttons function in much the same way as a two-button mouse.
Features & Components Elan TouchPad Once you have installed the touchpad driver (see “Touchpad” on page 4 - 7) you can configure the functions by double-clicking the touchpad driver icon in the notification area of the taskbar (or from Options in the ELAN tab in the Mouse control panel in Windows). You may then configure the gestures and options to your preferences.
Features & Components The Elan Smart-Pad control panel allows you to use a specific gesture (action) on the surface of the touchpad to perform specific actions to manipulate documents, objects and applications. 2 Click the menu tabs (One-finger, Multi-finger or Additional) and then the function button on the left to access the Configuration controls in the right panel. Click the tick box to Enable most of the controls and click Apply to save the settings.
Features & Components Click the Function Description tion. Click the Default button to get a detailed description of any func- 2 button to set any of the functions to the default setting.
Features & Components One-Finger 2 Tapping One-Finger tapping is equivalent to clicking the left mouse button to perform a point/click/select function. Figure 2 - 6 Tapping Button The left and right touchpad buttons may be configured to perform any action listed in the Button drop-down menu.
Features & Components Drag and Drop You can select the different drag and drop methods from the menu provided. The object can be released when you lift the finger off the touchpad, when you tap again or after a set time delay. 2 Figure 2 - 8 Drag and Drop Edge Scroll Enable Vertical or Horizontal Scroll from this menu. You can configure the width of the scrollable area by adjusting the slider accordingly. To scroll vertically, tap the right edge of the touchpad and drag the finger up and down.
Features & Components Edge Swipe Enable Edge Swipe to use a single finger to scroll from the edges of the touchpad to perform the designated function in Windows 8.
Features & Components Multi-Finger 2 Zooming Place two fingers on the touchpad (for best results use the tips of the fingers) and slide them apart to zoom in, or closer together to zoom out. Figure 2 - 11 Zooming Scrolling The Two-Finger scrolling feature works in most scrollable windows and allows you to scroll horizontally and vertically. Tap the pad surface and slide both fingers in the direction required (vertically or horizontally as long as the option is selected).
Features & Components Rotation You can rotate objects by using a two-finger gesture. Touch and rotate using two fingers on the pad in the direction required. Alternatively place a finger down on the pad and rotate the other finger around it in a circular motion (clockwise or counterclockwise). 2 Figure 2 - 13 Rotation Three Finger Swipe This gesture is used to activate a Page Up/Page Down operation.
Features & Components Additional 2 Palm Tracking This feature helps guard against accidental contact such as palms resting on the pad. Use the slider to adjust the sensitivity of the feature as appropriate. Figure 2 - 15 Palm Tracking Sensitivity Adjust the level of finger pressure required for the cursor to respond from this menu.
Features & Components 2 Volume Adjustment The sound volume level can be set using the volume control in the Settings menu in the Charms Bar. Audio Features You can configure the audio options on your computer from the Sound control panel in Windows, or from the Realtek HD Audio Manager icon in the taskbar notification area/control panel (right-click the taskbar notification area icon to bring up an audio menu).
Features & Components Setup for Audio Recording 2 To record audio sources on your computer at optimum quality follow the instructions below: 1. 2. 3. 4. Go to the Control Panel. Click Realtek HD Audio Manager (Hardware and Sound), or right-click the taskbar icon and select Sound Manager. Click Microphone Effects (tab) in Microphone (tab), and then click to select Noise Suppression (button), or adjust the Recording Volume level to around 60, to obtain the optimum recording quality.
Features & Components 2 2 - 16
Power Management Chapter 3: Power Management Overview To conserve power, especially when using the battery, your computer power management conserves power by controlling individual components of the computer (the monitor and hard disk drive) or the whole system.
Power Management 3 Forced Off If the system “hangs”, and the Ctrl + Alt + Del key combination doesn’t work, press the power button for 4 seconds, or longer, to force the system to turn itself off. The Power Sources The computer can be powered by either an AC/DC adapter or a battery pack. AC/DC Adapter Use only the AC/DC adapter that comes with your computer. The wrong type of AC/ DC adapter will damage the computer and its components. 1. 2. 3. 4.
Power Management Turning On the Computer Now you are ready to begin using your computer. To turn it on simply press the power button on the front panel. When the computer is on, you can use the power button as a Stand by/Hibernate/ Shutdown hot-key button when it is pressed for less than 4 seconds (pressing and holding the power button for longer than this will shut the computer down). Use Power Options (Hardware and Sound) in the Windows control panel to configure this feature.
Power Management 3 Resuming Operation See Table 3 - 1, on page 3 - 10 for information on how to resume from a power-saving state. Password It is recommended that you enable a password on system resume in order to protect your data. Figure 3 - 2 Power Plan Advanced Settings 3 - 4 Power Plans Power Plans The computer can be configured to conserve power by means of power plans. You can use (or modify) an existing power plan, or create a new one.
Power Management Each Windows power plan will also adjust the processor performance of your machine in order to save power. This is worth bearing in mind if you are experiencing any reduced performance (especially under DC/battery power). 3 Choose High performance (you may need to click Show additional plans to view the High performance plan) for maximum performance when the computer is powered from an AC power source.
Power Management 3 Wake On LAN Support (Windows 8) Wake-On-LAN is only supported from Sleep or Hibernate states in Windows 8. If you require your computer to wake up from network activity in Windows 8 then make sure that the computer is either in Sleep or Hibernate. Wake-On-LAN is not supported from Shutdown states in Windows 8. Power-Saving States You can use power-saving states to stop the computer’s operation and restart where you left off.
Power Management Hibernate Hibernate uses the least amount of power of all the power-saving states and saves all of your information on a part of the hard disk before it turns the system off. If a power failure occurs the system can restore your work from the hard disk; if a power failure occurs when work is saved only to memory, then the work will be lost. Hibernate will also return you to where you last left off within seconds.
Power Management 3 Password Protection Configuring the Power Buttons The power/sleep button (Fn + F4 key combo) and closed lid may be set to send the computer in to a power-saving state. Click Choose what the power buttons do on the left menu in Power Options to bring up the menu. It is recommended that you enable a password on wake up in order to protect your data.
Power Management Adding Hibernate/Sleep to the Power Menu Add Hibernate/Sleep to the Power Menu as follows. 1. 2. 3. 4. 5. Go to the Power Options (Hardware and Sound) control panel (see page 1 - 27). Click “Change settings that are currently unavailable” . Click Choose what the power buttons do. Click to put a tick in the Hibernate/Sleep box under Shutdown settings. Click Save Changes and close the control panel.
Power Management Resuming Operation You can resume operation from power-saving states by pressing the power button, or in some cases pressing the sleep button (Fn + F4 key combo).
Power Management Power Conservation Modes This system supports Energy Star power management features that place computers (CPU, hard drive, etc.) into a low-power sleep modes after a designated period of inactivity. Adjust Power Conservation Modes from the Control Center: 1. 2. 3. Press the Fn + Esc key combination to toggle the Control Center on/off. Click either the Performance, Balanced or Energy Star button.
Power Management Ctrl + Alt + Delete Key Combination You can use the CTRL + ALT + DEL key combination from almost any of the Windows 8 interfaces/Apps to bring up a full-screen displaying Lock, Switch User, Log off, Change a password and Task Manager options. If you click the Power icon in the lower right corner of the screen a power management option menu appears to display Sleep, Shut down, and Restart.
Power Management Battery Information Follow these simple guidelines to get the best use out of your battery. Low Battery Warning Battery Power Your computer’s battery power is dependent upon many factors, including the programs you are running, and peripheral devices attached. You can set actions to be taken (e.g. Shut down, Hibernate etc.), and set critical and low battery levels from power plan Change plan settings > Change advanced power settings (see Figure 3 - 3 on page 3 - 5).
Power Management 3 Windows Mobility Center The Windows Mobility Center control panel provides an easy point of access for information on battery status, power plans used and wireless device status etc. Conserving Battery Power • Use a power plan that conserves power (e.g Power saver), however note that this may have an affect on computer performance. • Lower the brightness level of the LCD display.
Power Management Battery Life Battery life may be shortened through improper maintenance. To optimize the life and improve its performance, fully discharge and recharge the battery at least once every 30 days. We recommend that you do not remove the battery yourself. If you do need to remove the battery for any reason (e.g. long term storage or system upgrade) see “Removing the Battery” on page 6 - 3.
Power Management 3 Caution Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Discard used battery according to the manufacturer’s instructions.
Power Management Battery FAQ How do I completely discharge the battery? Use the computer with battery power until it shuts down due to a low battery. Don’t turn off the computer even if a message indicates the battery is critically low, just let the computer use up all of the battery power and shut down on its own. 1. 2. 3 Save and close all files and applications. Create a power plan for discharging the battery and set all the options to Never.
Power Management 3. Click Change plan settings (after creating it) and click Change plan settings > Change advanced power settings.
Power Management 4. 5. Scroll down to Battery and click + to expand the battery options.
Power Management 3 How do I fully charge the battery? When charging the battery, don’t stop until the LED charging indicator light changes from orange to green. How do I maintain the battery? Completely discharge and charge the battery at least once every 30 days or after about 20 partial discharges.
Drivers & Utilities Chapter 4: Drivers & Utilities This chapter deals with installing the drivers and utilities essential to the operation or improvement of some of the computer’s subsystems. The system takes advantage of some newer hardware components for which the latest versions of most available operating systems haven’t built in drivers and utilities. Thus, some of the system components won’t be auto-configured with an appropriate driver or utility during operating system installation.
Drivers & Utilities Driver Installation 4 1. 2. 3. 4. Insert the Device Drivers & Utilities + User’s Manual disc into the attached DVD drive. Click the message “Tap to choose what happens with this disc.” Click Run autorun.exe. Click Install Drivers (button), or Option Drivers (button) to access the Optional driver menu.
Drivers & Utilities 5. 6. 7. Check the driver installation order from Table 4 - 1, on page 4 - 4 (the drivers must be installed in this order) which is the same as that listed in the Drivers Installer menu below. Click to select the driver you wish to install, (you should note down the drivers as you install them). Follow the instructions for each individual driver installation procedure as listed on the following pages.
Drivers & Utilities Win 8 Driver 4 Page # Optional Items Page # Chipset Page 4 - 7 PC Camera Module (No driver required for Windows 8) Page 7 - 2 Video (VGA) Page 4 - 7 Wireless LAN Module Page 7 - 9 LAN Page 4 - 7 Bluetooth & WLAN Combo Module Page 7 - 17 CardReader Page 4 - 7 Trusted Platform (Security) Module Page 7 - 23 Touchpad Page 4 - 7 Intel® Rapid Storage Technology (required for hard disks in AHCI/RAID mode and for Intel® Smart Response Technology) Airplane Page 4 - 7 Int
Drivers & Utilities Manual Driver Installation Click Browse CD/DVD (button) in the Drivers Installer application and browse to the executable file in the appropriate driver folder. Windows Update After installing all the drivers make sure you enable Windows Update in order to get all the latest security updates etc. (all updates will include the latest hotfixes from Microsoft). See “Windows Update” on page 4 9 for instructions.
Drivers & Utilities User Account Control 4 If a User Account Control prompt appears as part of the driver installation procedure, click Continue or Allow, and follow the installation procedure as directed. Windows Security Message If you receive a Windows security message as part of the driver installation process. Just click “Install this driver software anyway” or “Install” to continue the installation procedure.
Drivers & Utilities Driver Installation Procedure Insert the Device Drivers & Utilities + User’s Manual disc into an attached optical (DVD) drive and click Install Drivers/Option Drivers (button). Chipset 1. Click 1.Install Chipset Driver > Yes. 2. Click Next > Yes > Next > Next. 3. Click Finish to restart the computer. Video (VGA) 1. Click 2.Install VGA Driver > Yes. 2. Click Next > Yes > Next > Next. 3. Click Finish to restart the computer.
Drivers & Utilities Hot Key 1. Click 8.Install Hotkey AP > Yes. 2. Click Next > Next. 3. Click Finish > Finish to restart the computer. 4 MEI Driver 1. Click 9.Install MEI Driver > Yes. 2. Click Next > Yes > Next. 3. Click Finish. Audio 1. Click 10. Install Audio Driver > Yes. 2. Click Next. 3. Click Finish to restart the computer. 4 - 8 Driver Installation Note that after installing the audio driver the system will not return to the Drivers Installer screen.
Drivers & Utilities Windows Experience Index Windows Update After installing all the drivers make sure you enable Windows Update in order to get all the latest security updates etc. (all updates will include the latest hotfixes from Microsoft). To enable Windows Update make sure you are connected to the internet: 1. 2. 3. 4. 5. 6. Go to the Control Panel. Click Windows Update (System and Security/ Security). Click Check for updates (button).
Drivers & Utilities Optional Drivers See the pages indicated in Table 4 - 1, on page 4 - 4 for the driver installation procedures for any modules included in your purchase option. 4 Optional Driver Installation Note Note that driver # 4 (Sound Blaster Cinema) is not required for this particular model. Figure 4 - 3 - Option Drivers Note that you need to install both the WLAN & Bluetooth drivers for Intel and 3rd party WLAN & Bluetooth Combo modules.
BIOS Utilities Chapter 5: BIOS Utilities Overview This chapter gives a brief introduction to the computer’s built-in software: If your computer has never been set up, or you are making important changes to the system (e.g. hard disk setup), then you should review this chapter first and note the original settings found in Setup. Even if you are a beginner, keep a record of the settings you find and any changes you make. This information could be useful if your system ever needs servicing.
BIOS Utilities BIOS Settings Warning 5 Incorrect settings can cause your system to malfunction. To correct mistakes, return to Setup and restore the Previous Values with , or Optimized Defaults with . UEFI Boot & POST When UEFI Boot is enabled, then the prompts to press F2 or F7 will not appear. However you can still press F2 to enter the setup, or F7 to choose the preferred boot device, if you press the key immediately the system boots up.
BIOS Utilities Failing the POST Errors can be detected during the POST. There are two categories, “fatal” and “nonfatal”. Fatal Errors These stop the boot process and usually indicate there is something seriously wrong with your system. Take the computer to your service representative or authorized distributor/supplier as soon as possible. Non-Fatal Errors This kind of error still allows you to boot.
BIOS Utilities Setup Menus 5 The Setup menus shown in this section are for reference only. Your computer’s menus will indicate the configuration appropriate for your model and options. Setup Screens The following pages contain additional advice on portions of the Setup. Along the top of the screen is a menu bar with menu headings. When you select a heading, a new screen appears. Scroll through the features listed on each screen to make changes to Setup.
BIOS Utilities Main Menu Figure 5 - 2 Main Menu System Time & Date (Main Menu) The hour setting uses the 24-hour system (i.e., ØØ = midnight; 13 = 1 pm). If you can change the date and time settings in your operating system, you will also change these settings. Some applications may also alter data files to reflect these changes.
BIOS Utilities SATA Port # (Main Menu) Pressing Enter opens the sub-menu to show the configuration of a optical Device/ HDD on the computer’s SATA Ports. CPU/System/Extended Memory: (Main Menu) This item contains information on the CPU type and system memory, and is not user configurable. The system will auto detect the amount of memory installed. 5 MB Series / BIOS Revision / KBC/EC firmware Revision This item contains information on the BIOS version etc., and is not user configurable.
BIOS Utilities Advanced Menu Figure 5 - 3 Advanced Menu 5 Intel Smart Connect Technology (Advanced Menu) Smart Connect is a technology that makes checks on web applications that are open even when the computer is in sleep mode, and thus allows updates to be made without the need to turn the computer on. The sub-menus here allow you to enable/disable the technology (ISCT Configuration).
BIOS Utilities UEFI Boot 5 When UEFI Boot is enabled, then the prompts to press F2 or F7 will not appear. However you can still press F2 to enter the setup, or F7 to choose the preferred boot device, if you press the key immediately the system boots up. Intel(R) Rapid Start Technology (Advanced Menu) Enable/disable Intel(R) Rapid Start Technology from this menu. The rapid start hibernation mode can resume power within 5 to 6 seconds and can remember your computer's state with zero power.
BIOS Utilities Power On Boot Beep (Advanced Menu) Use this menu item to enable/disable the beep as the computer starts up. Battery Low Alarm Beep (Advanced Menu) Use this menu item to enable/disable the battery low alarm beep.
BIOS Utilities Security Menu Security Menu 5 The changes you make here affect the access to the Setup utility itself, and also access to your machine as it boots up after you turn it on. These settings do not affect your machine or network passwords which will be set in your software OS. Figure 5 - 4 Security Menu Set Supervisor Password (Security Menu) You can set a password for access to the Aptio Setup Utility. This will not affect access to the computer OS (only the Aptio Setup Utility).
BIOS Utilities Note: To clear existing passwords press Enter and type the existing password, then press Enter for the new password (without typing any password entry) and Enter again to confirm the password clearance. Set User Password (Security Menu) You can set a password for user mode access to the Aptio Setup Utility. This will not affect access to the computer OS, (only the Setup utility) unless you choose to set a Password on Boot (see below).
BIOS Utilities Secure Boot Control (Security Menu) Secure Boot prevents unauthorized operating systems and software from loading during the startup process. Secure Boot Control is available as a menu option if you have enabled UEFI Boot (see “UEFI Boot (Boot Menu)” on page 5 - 17). Enabling Secure Boot will bring up the Secure Boot Mode menu to enable you to configure Secure Boot as Standard (with a fixed secure boot policy) or Custom (which enables you to make changes to the Key Management database).
BIOS Utilities TPM Configuration (Security Menu) This sub-menu will allow you to enable/disable Trusted Platform Module (TPM) support, and to configure the TPM State. Select TPM Configuration and press Enter to access the sub-menu. Press Enter to access the Security Device Support menu and select Enable to display the full TPM configuration menu (see “Trusted Platform (Security) Module” on page 7 - 23 for details).
BIOS Utilities TPM State (Security Menu > Security Device Support Enabled) Select TPM State, press Enter and select Enabled to change the TPM state to enabled. You will then need to press F4 to save the changes and restart the computer. 5 Figure 5 - 6 TPM State (Enabled) As the computer restarts press F2 to enter the BIOS again and go to the TPM Configuration menu.
BIOS Utilities Pending TPM operation (Security Menu > Security Device Support & TPM State Enabled) Select Pending operation, press Enter and select the option you require (if you are initializing TPM you should select Enable Take Ownership). You will then need to press F4 to save the changes and restart the computer. You can now install the TPM driver (see “Trusted Platform Module (TPM) Driver Installation” on page 7 - 26) and then initialize the TPM.
BIOS Utilities Boot Menu Figure 5 - 8 Boot Menu 5 BIOS Screens Note that the BIOS screens pictured on these pages are intended for guidance in setting up your system’s BIOS. BIOS versions are subject to constant change and revision, therefore your computer’s actual screens may appear slightly different from those pictured on these pages. 5 - 16 Boot Menu When you turn the computer on it will look for an operating system (e.g.
BIOS Utilities Boot Option Priorities (Boot Menu) Press Enter to access the menu, use the arrow keys to move up and down the menu, and press Enter to select a device from the Boot Option # list (the selected device will be highlighted in white). UEFI Boot (Boot Menu) Enable/disable UEFI Boot from this menu. The Unified Extensible Firmware Interface (UEFI) specification provides a clean interface between operating systems and platform firmware at boot time.
BIOS Utilities Exit Menu Figure 5 - 9 Exit Menu 5 Click Save Changes and Reset to save all changes made. Choosing to Discard Changes, or Exit Discarding Changes, will wipe out any changes you have made to the Setup. You can also choose to restore the original Setup defaults that will return the Setup to its original state, and erase any previous changes you have made in a previous session.
Upgrading The Computer Chapter 6: Upgrading The Computer Overview This chapter contains information on upgrading the computer. Follow the steps outlined to make the desired upgrades. If you have any trouble or problems you can contact your service representative for further help.
Upgrading The Computer When Not to Upgrade Power Safety Warning 6 Before you undertake any upgrade procedures, make sure that you have turned off the power, and disconnected all peripherals and cables (including telephone lines). It is advisable to also remove your battery in order to prevent accidentally turning the machine on. These procedures involve opening the system’s case, adding and sometimes replacing parts.
Upgrading The Computer Removing the Battery If you are confident in undertaking upgrade procedures yourself, for safety reasons it is best to remove the battery. 1. 2. 3. 4. 5. Turn the computer off, and turn it over. Slide the latch 1 in the direction of the arrow. Slide the latch 2 in the direction of the arrow, and hold it in place. Slide the battery out in the direction of the arrow 3 . Reinsert the battery as illustrated below 4 .
Upgrading The Computer Removing the Component Bay Cover 1. 2. 3. 4. Turn off the computer, and turn it over and remove the battery (see page 6 - 3). Remove screws 1 & 2 from the bottom of the computer. Slide the component bay cover until the cover and case indicators 3 are aligned. Lift the bottom cover 4 off the computer case.
Upgrading The Computer Replacing the Component Bay Cover 1. 2. 3. Reinsert the component bay cover by placing it on the bottom case assembly, and make sure the case markers line up 1 . Apply downward pressure and sliding the cover in the direction of arrow 2 . Replace screws 1 & 2 (Figure 6 - 2 on page 6 - 4) and battery (see page 6 - 3).
Upgrading The Computer HDD System Warning 6 New HDD’s are blank. Before you begin make sure: You have backed up any data you want to keep from your old HDD. You have all the discs required to install your operating system and programs. If you have access to the internet, download the latest application and hardware driver updates for the operating system you plan to install. Copy these to a removable medium.
Upgrading The Computer Removing the Hard Disk Bay Cover 1. 2. 3. 4. Turn off the computer, and turn it over and remove the battery (see page 6 - 3). Remove screws 1 & 2 from the bottom of the computer. Slide the HDD bay cover in the direction of arrow 3 until the cover and case indicators 4 are aligned. Remove the HDD bay cover 5 .
Upgrading The Computer Replacing the HDD Bay Cover 1. 2. 3. Reinsert the HDD bay cover by placing it on the bottom case assembly, and make sure the case markers line up 1 . Apply downward pressure with both thumbs at points 2 & 3 and slide the cover in the direction of the arrows as illustrated. Replace screws 1 & 2 (Figure 6 - 4 on page 6 - 7) and battery (see page 6 - 3).
Upgrading The Computer Removing the HDD 1. 2. 3. 4. 5. 6. Remove the HDD bay cover (see page 6 - 7). Grip the tab 1 and slide the HDD assembly in the direction of arrow 2 . Remove the HDD assembly 3 . Remove screws 4 & 5 and the cover 6 . Replace the HDD assembly by using a finger to push it in at point 7 in the direction of arrow 8 . Replace the component bay cover and screws.
Upgrading The Computer Removing the SSD From the Component Bay 1. 2. 3. 4. 5. 6. 6 7. Remove the component bay cover (see page 6 - 4). The SSD slot is at point 1 on the mainboard. Remove screw 2 . The SSD 3 will pop-up and you can then remove it. Replace the SSD by angling it as illustrated, and then fit the connector firmly into the slot. The SSD module’s pin alignment will allow it to only fit one way. Make sure the module is seated as far into the slot as it will go.
Upgrading The Computer Upgrading the System Memory (RAM) The computer has two memory sockets for 204 pin Small Outline Dual In-line (SODIMM) DDR3L type memory modules (see “Memory” on page D - 2 for details of supported module types). 1. 2. Turn off the computer, and turn it over and remove the battery (see page 6 - 3) and component bay cover (see page 6 - 4). The memory sockets will be visible at point 1 .
Upgrading The Computer 3. Gently pull the two release latches on the sides of the memory socket in the direction indicated by the arrows ( 2 & 3 ) in Figure 6 - 9. Figure 6 - 9 RAM Module Release Latches 2 3 6 2 3 Contact Warning Be careful not to touch the metal pins on the module’s connecting edge. Even the cleanest hands have oils which can attract particles, and degrade the module’s performance. Figure 6 - 10 RAM Module Removal 4. The RAM module will 4 pop-up, and you can remove it.
Upgrading The Computer 5. 6. 7. 8. 9. Pull the latches to release the second module if necessary. Insert a new module holding it at about a 30° angle and fit the connectors firmly into the memory slot. The module’s pin alignment will allow it to only fit one way. Make sure the module is seated as far into the slot as it will go. DO NOT FORCE the module; it should fit without much pressure. Press the module in and down towards the mainboard until the slot levers click into place to secure the module.
Upgrading The Computer 6 6 - 14
Modules & Options Chapter 7: Modules & Options Overview This chapter contains information on the following modules, which may come with your computer, depending on the configuration purchased. If you are unsure please contact your service representative.
Modules & Options PC Camera Module When the PC Camera application is run the LED indicator to the left of the camera will be illuminated in red (see 2 Figure on page 1 - 6). Note that you need to use the Camera app in Windows 8 to take pictures and capture video. Use the Fn + F10 key combination (see “Function/Hot Key Indicators” on page 1 - 10) to toggle power to the PC Camera module.
Modules & Options PC Camera Audio Setup If you want to capture video & audio with your camera, it is necessary to setup the audio recording options in Windows. 1. 2. 3. 4. 5. 6. Go to the Control Panel. Click Sound (Hardware and Sound) and click Recording (tab). Right-click hold and release Microphone (Realtek High Definition Audio) and make sure the item is not disabled. Double-click Microphone (or select Properties from the right-click menu).
Modules & Options Camera App 1. 2. 3. Make sure the camera is powered on (use the Fn + F10 key combination to toggle power to the camera module). Click the Camera app icon in the Start screen to run the Camera app . The camera interface is a translucent app bar with three buttons. Figure 7 - 2 Camera App Bar • Camera options:.
Modules & Options You can also click on More to adjust Brightness, Contrast and Flicker (if you find that the video screen in the camera program is flickering, you can try to adjust the setting here). Eliminating Screen Flicker If you find that the video screen in the camera program is flickering, you can try to adjust the setting in Flicker under More Options.
Modules & Options Taking Pictures/Capturing Video 1. 2. 3. 4. 5. 6. 7. 7 Figure 7 - 5 Libraries - Pictures 7 - 6 PC Camera Module Make sure the camera is powered on (use the Fn + F10 key combination to toggle power to the camera module). Click the Camera app icon in the Start screen to run the Camera app . Click to select the timer if you require a countdown before capture. Click to select either photo or video modes.
Modules & Options 8. A scroll arrow will appear on the left side of the screen after any pictures/videos have been captured. 9. Click the arrows (on either side of the screen) to browse through the captured photos/video, and back to the Camera app. 10. Clicking on a captured photo will bring up an app bar with Crop and Delete buttons. Figure 7 - 6 Crop & Delete Buttons (for Still Photos) 11. Use the handles to Crop any captured picture, and click OK to save the changes made. 12.
Modules & Options Reducing Video File Size Note that capturing high resolution video files requires a substantial amount of disk space for each file. After recording video, check the video file size (right-click the file and select Properties) and the remaining free space on your hard disk (go to My Computer, right-click the hard disk, and select Properties). If necessary you can remove the recorded video file to a removable medium e.g. CD, DVD or USB Flash drive.
Modules & Options Wireless LAN Module If you have included an Intel® or 3rd Party WLAN module in your purchase option make sure that the module is on (i.e. the system is not in Airplane Mode) before installing the driver. Make sure you install the drivers in the order indicated in Table 4 - 1, on page 4 - 4. Note that you need to install both the WLAN & Bluetooth drivers for the WLAN & Bluetooth Combo modules.
Modules & Options 3rd Party 802.11b/g/n Driver Installation 1. Make sure the system is not in Airplane Mode, and then insert the Device Drivers & Utilities + User’s Manual disc into an attached DVD drive. 2. Click Option Drivers (button). 3. Click 1.Install WLAN Driver > Yes. 4. Click Next. 5. Click Finish to restart the computer. 6. The operating system is the default setting for Wireless LAN control in Windows (see page 7 - 11). 7 Intel® WLAN Driver Installation 1.
Modules & Options WLAN Configuration in Windows 8 You can configure a wireless connection using one of the following options, however make sure the Wireless LAN module is turned on (and not in Airplane Mode) before configuration begins. Charms Bar 1. 2. 3. Go to the Charms Bar. Select Settings and then click the WiFi icon (it should read Available under the icon and Airplane mode should be Off). A list of available access points will appear.
Modules & Options 4. 5. 6. 7. 8. Double-click an access point to connect to it (or click it and click Connect). Enter a network security key (password) if required, and click Next. You can choose to share or connect to devices or not. When you are connected to the network access point it will display the Connected icon . Select any connected network and click Disconnect to disconnect from a connected access point. 7 Figure 7 - 9 Networks Connected / Disconnect 9.
Modules & Options 11. You need to either use Airplane Mode, or to turn the WLAN module off aboard aircraft.
Modules & Options Desktop Mode 1. 2. 3. 4. 5. 6. 7. Switch to the Windows Desktop (click the app or use the Windows logo key D key combination). Click the wireless icon in the notification area of the taskbar. A list of available access points will appear. Double-click an access point to connect to it (or click it and click Connect). Enter a network security key (password) if required, and click Next. You can choose to share or connect to devices or not.
Modules & Options Control Panel If you are in Category View do the following (see over for Icon View): 1. 2. 3. Open the Control Panel. Click the Network and Internet control panel. Click Connect to a network. Figure 7 - 12 Network and Internet Control Panel 4. 5. 6. 7. 8. A list of available access points will appear. Double-click an access point to connect to it (or click it and click Connect). Enter a network security key (password) if required, and click Next.
Modules & Options If you are in Icon View do the following: 1. 2. 3. 4. Open the Control Panel. Click Network and Sharing Center. Click Change Adapter Settings. Double-click Wi-Fi. 5. 6. 7. 8. 9. A list of available access points will appear. Double-click an access point to connect to it (or click it and click Connect). Enter a network security key (password) if required, and click Next. You can choose to share or connect to devices or not.
Modules & Options Bluetooth & WLAN Combo Module If your purchase option includes the Combination Wireless LAN & Bluetooth module (either Intel® or 3rd Party) then install the driver as instructed overleaf. Make sure that the module is on (i.e. the system is not in Airplane Mode) before installing the driver. Bluetooth Data Transfer 7 Note that the transfer of data between the computer and a Bluetooth enabled device is supported in one direction only (simultaneous data transfer is not supported).
Modules & Options High Speed Bluetooth Data Transfer 7 The Combination Wireless LAN & Bluetooth module supports high speed data transfer. However to achieve such transfer speeds, both devices must support high speed data transfer. To obtain high speed data transfer make sure that both the WLAN and Bluetooth modules are powered on. Check your Bluetooth compatible device’s documentation to confirm it supports high speed data transfer. 3rd Party Bluetooth (V4.0) Combo Driver Installation 1.
Modules & Options Bluetooth Configuration in Windows 8 You can configure a Bluetooth connection as below, however make sure the Bluetooth module is on (i.e. not in Airplane Mode) before configuration begins. Desktop Mode 1. 2. 3. Switch to the Windows Desktop (click the App or use the Windows logo key D key combination). Click the notification area of the taskbar and double-click the Bluetooth icon click and select Show Bluetooth Devices). The Devices item in PC Settings will appear.
Modules & Options 4. 5. Click Add a Device. Double-click the device you want to pair with the computer. 6. On first connection the computer will provide you with a pairing code to be entered onto the device. 7. Enter the code into your Bluetooth enabled device and click Yes on the computer to complete the pairing.
Modules & Options 8. You need to either use Airplane Mode, or to turn the Bluetooth module off aboard aircraft.
Modules & Options To Make your Computer Discoverable to Bluetooth Devices 1. 2. 3. 4. Switch to the Windows Desktop (click the app or use the Windows logo key + D key combination). Click the notification area of the taskbar, click the Bluetooth icon and click Open Settings. Click Options, and make sure that Allow Bluetooth devices to find this computer check box (Discovery) has a tick inside it.
Modules & Options Trusted Platform (Security) Module If your purchase option includes the TPM security chip, this allows you to create and manage digital certificates for user and platform authentication. This type of security is usually administered within large enterprises and organizations, and therefore requires implementation by a system administrator before users can access security features. Individual users can use the TPM as an authentication with the fingerprint reader.
Modules & Options Enabling & Activating TPM 1. 2. 3. 4. 5. 6. 7 Restart the computer. Enter the Aptio Setup Utility pressing F2 during the POST/startup. Use the arrow keys to select the Security menu. Select TPM Configuration and press Enter to access the sub-menu. Press Enter to access the Security Device Support menu and select Enable to display the full TPM configuration menu. Select TPM State, press Enter and select Enabled to change the TPM state to enabled.
Modules & Options 8. Select Pending operation, press Enter and select the option you require (if you are initializing TPM you should select Enable Take Ownership). You will then need to press F4 to save the changes and restart the computer. Figure 7 - 20 Pending operation (Enable Take Ownership) 9. You can now install the TPM driver (see “Trusted Platform Module (TPM) Driver Installation” on page 7 - 26) and then initialize the TPM.
Modules & Options 7 Trusted Platform Module (TPM) Driver Installation 1. Make sure you have enabled and activated the TPM in the BIOS before installing the driver. 2. Insert the Device Drivers & Utilities + User’s Manual disc into an attached DVD drive. 3. Click Option Drivers (button). 4. Click 3.Install TPM Driver > Yes. 5. Click Next. 6. Click the button to accept the license and click Next. 7. Click Next > Next > Install. 8. Click Finish > Yes to restart the computer.
Modules & Options Initializing TPM 1. 2. 3. 4. 5. Switch to the Desktop app and click the TPM icon right-click the icon in the notification area of the taskbar, and select Security Platform Initialization (or click the Security Platform State taskbar bubble). Click User Settings (tab) and click Yes, or right-click the icon in the notification area of the taskbar, and select Security Platform Initialization (or click the Security Platform State taskbar bubble).
Modules & Options 6. Help 7. Choose the Security Platform Features you want to use by clicking the appropriate tickbox. Enter a Basic User Password (and re-type to confirm it) and click Next. Right-click the icon in the notification area of the taskbar to bring up the menu to select Help or How to use the Security Platform Features. 7 You can also click the Help button in any of the Infineon Security Platform Settings Tool tabs to bring up specific help topics on each tab.
Modules & Options Infineon Security Platform Settings Tool The Infineon Security Platform Settings Tool allows you to manage and check the TPM state, manage your password information, and to backup and restore the TPM data. As TPM is usually administered within large enterprises and organizations, your system administrator will need to assist you in managing the information here. Menus Note that not all the menus pictured here will be available for access.
Modules & Options User Settings This page allows the settings to be configured for the currently logged in Infineon Security Platform user including the ability to change the password, configure secure e-mail, file and folder encryption and Enhanced Authentication. You can also import or delete certificates protected by the security platform.
Modules & Options Backup Here you can configure backup and restore operations. Backup files contain the computer identification and user identification information which is used to match the machine name and user name with the current machine and user during restoration.
Modules & Options Migration The Migration tab is used to help securely transfer keys and certificates from one platform to another.
Modules & Options Password Reset Use Password Reset to reset basic user passwords when required.
Modules & Options BitLocker BitLocker Drive Encryption can be used in conjunction with the TPM to encrypt data on the disk and is done via the Microsoft BitLocker Control Panel Applet. Click Configure and select a drive to be encrypted and then follow the Wizard to begin the encryption process.
Modules & Options Access the Microsoft BitLocker Drive Encryption control panel applet from the Windows control panel (System and Security).
Modules & Options Advanced Configure all the Security Platform owner and policy settings from the Advanced tab. The settings that can be changed are for the local computer only.
Modules & Options Intel® Rapid Storage Technology Install the Intel® Rapid Storage Technology to support your AHCI mode SATA drive. IRST Driver Installation 1. Insert the Device Drivers & Utilities + User’s Manual disc into an attached DVD drive. 2. Click Option Drivers (button). 3. Click 5.Install IRST Driver > Yes. 4. Click Next. 5. Click in the tickbox to accept the license and click Next. 6. Click Next > Next > Next. 7. Click Finish to restart the computer. 8.
Modules & Options Intel® Smart Response Technology 7 Support for Intel® Smart Response Technology is dependent on your processor. For details contact your distributor/ supplier. Intel® Smart Response Technology Intel® Smart Response Technology is an Intel® Rapid Storage Technology (RST) caching feature that accelerates computer system performance by using the SSD as cache memory between the hard disk drive and system memory.
Modules & Options Enabling Intel Smart Response Technology 1. 2. Run the Intel® Rapid Storage Technology application. Click Enable acceleration under Performance > Smart Response Technology (note that you will at least 5MB of free unpartitioned and unallocated space on the SSD otherwise the Smart Response Technology item will not appear). Figure 7 - 32 Intel® Rapid Storage Technology Performance Enable Acceleration 3. 4. Select the SSD to be used as a cache device.
Modules & Options 5. 6. Select the HDD (or RAID volume) to be accelerated (it is highly recommended that you accelerate the system volume or system disk for maximum performance). Select the acceleration mode, and then click OK (Enhanced mode is selected by default). Note: Enhanced mode (default): Acceleration optimized for data protection. Maximized mode: Acceleration optimized for input/output performance.
Modules & Options 7. The page will refresh and report the new configuration in under Performance > Smart Response Technology.
Modules & Options Intel® Rapid Start Technology Intel(R) Rapid Start Technology can resume power from Hibernation within 5 to 6 seconds and can remember your computer's previous state with zero power. System Requirements to support Intel® Rapid Start Technology: • Intel Rapid Storage Technology software installed. • A Solid State Drive (SSD) with a minimum capacity of 18.6GB. 7 See overleaf for instructions on enabling Intel® Rapid Start Technology.
Modules & Options Intel® Rapid Start Technology Configuration 1. 2. 3. Enable Intel(R) Rapid Start Technology from the BIOS (see “Intel(R) Rapid Start Technology (Advanced Menu)” on page 5 - 8). Go the Windows control panel and double-click Administrative Tools (System and Security)> Computer Management > Storage > Disk Management Right-click the SSD and select Shrink Volume from the menu.
Modules & Options 4. Enter the figure, which should be equal to amount of system memory (RAM) in your computer, in “Enter the amount of space to shrink in MB”. 5. Click Shrink (any unallocated file space may be formatted for storage use). Figure 7 - 36 Shrink Volume Size 7 Memory Size (Amount of Space to Shrink) The figure entered in the “Enter the amount of space to shrink in MB” field above should be equal to the amount of system memory in your computer.
Modules & Options 6. Run the Desktop app and right-click the lower left hot corner (or use the Windows Logo Key + X key combination) and select Command Prompt (Admin). Figure 7 - 37 Search for CMD Prompt 7 7. 8. Type “DISKPART”. At the DISKPART command type “list disk”.
Modules & Options 9. Type “select disk #” (# is disk number where you want to create the store partition, so refer to the results obtained from "list disk" for exact disk number). 10. The message “Disk # is now the selected disk.” will appear. Figure 7 - 39 Diskpart - Select Disk # 7 Figure 7 - 40 11. Type “create partition primary”. 12. A “DiskPart succeeded in creating the specified partition.” message should appear.
Modules & Options 13. Type “detail disk”. Figure 7 - 41 Diskpart - Detail Disk 7 14. Type “select Volume #” (# is volume of your storage partition so refer to results obtained from "detail disk" for the exact volume number). 15. The message “Volume # is now the selected volume.” will appear.
Modules & Options 16. Type the following, depending on the format of the SSD. • For MBR formatted SSDs: “set id=84 override” (the id must be set to 84). • For GPT formatted SSDs: “set id=D3BFE2DE-3DAF-11DF-BA40-E3A556D89593”. 7 Figure 7 - 43 Diskpart - Set id= 17. The message “DiskPart successfully set the partition ID.” will appear. 18. Close the CMD window.
Modules & Options 19. Go the Windows control panel and double-click Administrative Tools (System and Security)> Computer Management > Storage > Disk Management. 20. The disk partition should read Healthy Hibernation Partition. Figure 7 - 44 Computer Management (Healthy Hibernation Partition) Healthy (Hibernation Partition) 21. Restart the computer. 22. Install the driver (see below). Intel® Rapid Start Technology Driver Installation 1.
Modules & Options Intel® Smart Connect Technology System Requirements 7 Note that in order to support Intel® Smart Connect Technology your system will need to have the item enabled in the BIOS (see page 5 - 7). In addition only certain Intel WLAN modules support this feature. Intel® Smart Connect Technology Intel® Smart Connect Technology periodically, and briefly, wakes the computer from Sleep mode in order to update information for certain applications (e.g.
Modules & Options Intel® Smart Connect Technology Configuration 1. 2. 3. 4. Access the Intel(R) Smart Connect Technology application from the Start menu. Click Basic (tab) and adjust the slider to set the update frequency (note that the slider balances between “More Frequent Updates” and “More Battery Life”). Note the sidebar warning about the use of Intel(R) Smart Connect Technology aboard aircraft and make sure your wireless LAN module is off during air travel.
Modules & Options 7 5. 6. Click Advanced (tab) to access the Extended Power Savings settings. Extended Power Savings allows you to set a time period during which the computer will update less often (e.g. at night while you are asleep or whenever you are at work). 7. Updates set during this time period will be performed every two hours, and this will override the settings selected in the Basic tab in order to conserve power consumption.
Modules & Options 8. Click the Help tab and click Topics to access the main Help menu. Intel WLAN Modules If your purchase option includes an Intel WLAN module, (with Intel’s PROSet Wireless Connection Utility installed), Intel® Smart Connect Technology will search for WiFi networks around you that you have previously accessed. If no known WiFi networks are found, your computer will not update again until it recognizes a known WiFi network.
Modules & Options 9. Disable Intel Rapid Start Technology by clicking the Off button, and clicking Save. OR 10. Click Timer to make sure it is on, and adjust the slider to select a time to delay entering Rapid Start from running, and click Save.
Modules & Options Intel® Wireless Display Application The Intel® Wireless Display Application (requires Intel® Centrino WLAN/ Combo module), in conjunction with a compatible video adapter (purchased separately), allows you to display the contents of the notebook display on another display (e.g. HDTV) without the need to have cables stretching across a room. You can then play games, browse the internet, display videos or photo slide shows on your TV/external display without using HDMI or A/V cables.
Modules & Options Intel® WiDi Application Installation 1. Insert the Device Drivers & Utilities + User’s Manual disc into the DVD drive. 2. Click Option Drivers (button). 3. Click 8.Install Intel WiDi AP > Yes. 4. Click Next. 5. Click the button to accept the license and click Next. 6. Click Finish.
Modules & Options Intel® WiDi Application Configuration 1. 2. 3. Run Intel(R) Wireless Display from the Start screen. Click I agree to the terms of this license (button). The application will scan for any connected compatible adapters (or you can click the Scan for available adapters button to enable Intel My WiFi Technology).
Modules & Options 4. 5. 6. Click to select and detected adapters, and click Connect. The system will then prompt you to enter the 4-digit security code which will be displayed on the external TV Screen (or press the connect button on the wireless speaker adapter). Enter the code for the video adapter and click Continue.
Modules & Options 7. 8. You will then be prompted to enter a name for the video adapter and click Continue. Click Finished to complete the setup. Test Audio Adapter To verify a successful audio connection (for Intel® Wireless Music), select the “Test your audio connection” link or select “Finished” to bypass the test. You can select “Play Sample” to play an audio test sample from your adapter to the connected speaker set.
Modules & Options 3G Module If you have included an optional UMTS/HSPDA+ based 3G Module (Universal Mobile Telecommunications System or High Speed Packet Access) module (see “Communication” on page D - 3 for specification details) in your purchase option, you do not require a driver/application installation for Windows 8.
Modules & Options 3G Module USIM Card Installation If you have included an optional 3G module, follow the instructions below to install the USIM card (which will be provided by your service provider). 1. 2. 3. 4. 5. 6. Turn the computer off, remove the AC/DC adapter and turn it over. Slide the latch 1 in the direction of the arrow. Slide the latch 2 in the direction of the arrow, and hold it in place. Grip the battery and remove it in the direction of arrow 3 .
Modules & Options 3G Configuration in Windows 8 You can configure a 3G connection as below, however make sure the system is not in Airplane Mode before configuration begins. Charms Bar 1. 2. \ 3. 7 Figure 7 - 53 WiFi Settings (Charms Bar) & Networks (with Mobile Broadband) 7 - 62 3G Module Go to the Charms Bar. Select Settings and then click the WiFi icon (it should read Available under the icon and Airplane mode should be Off). A list of available access points will appear.
Modules & Options 4. 5. Any 3G service provider (connection information is usually stored on the USIM card) will appear under Mobile Broadband. Double-click any connection icon under Mobile Broadband (or click and click Connect). Figure 7 - 54 Mobile Broadband (Connect) 6. 7. The system will connect to your network. A Connected will appear alongside the 3G connection (click the connection to view the timer which indicates your connected time for the current session).
Modules & Options Wireless Device Operation Aboard Aircraft The use of any portable electronic transmission devices aboard aircraft is usually prohibited. 7 Make sure the system is in Airplane Mode if you are using the computer aboard aircraft. Figure 7 - 56 PC Settings (Wireless) 7 - 64 3G Module 8. You can then access the internet, download e-mail etc. as per any internet connection. 9. To disconnect you can select the connection and click Disconnect . 10.
Modules & Options EM820W 3G Module PIN Code & Power-Saving Note that there may be some issues when a PIN Code is set for the EM820W 3G module (if you are unsure of your module version contact your distributor/supplier) in Windows 8, Mobile Broadband has been turned off, and the system has resumed from a power-saving state. To prevent any issues it is recommended that you simply do not enable a PIN for the EM820W 3G module.
Modules & Options 4. 5. 6. Click Security (tab) and click Disable PIN. Enter the PIN number and click Disable PIN and click OK to confirm. It is recommended that you do not Enable a PIN for the EM820W 3G module.
Troubleshooting Chapter 8: Troubleshooting Overview Should you have any problems with your computer, before consulting your service representative, you may want to try to solve the problem yourself. This chapter lists some common problems and their possible solutions. This can’t anticipate every problem, but you should check here before you panic. If you don’t find the answer in these pages, make sure you have followed the instructions carefully and observed the safety precautions in the preface.
Troubleshooting Basic Hints and Tips Many of the following may seem obvious but they are often the solution to a problem when your computer appears not to be working. • Power - Is the computer actually plugged into a working electrical outlet? If plugged into a power strip, make sure it is actually working. Check the LED Power & Communication Indicators (see “LED Indicators” on page 1 - 7) to see the computer’s power status.
Troubleshooting Backup and General Maintenance • Always backup your important data, and keep copies of your OS and programs safe, but close to hand. Don’t forget to note the serial numbers if you are storing them out of their original cases, e.g. in a CD wallet. • Run maintenance programs on your hard disk and OS as often as you can. You may schedule these programs to run at times when you are not using your computer.
Troubleshooting Viruses • Install an Anti-Virus program and keep the definitions file (the file which tells your program which viruses to look for) up to date. New computer viruses are discovered daily, and some of them may seriously harm your computer and cause you to lose data. Anti-Virus programs are commercially available and the definitions file updates are usually downloadable directly from the internet. 8 • Be careful when opening e-mail from sources you don’t know.
Troubleshooting Upgrading and Adding New Hardware/Software • Do not be tempted to make changes to your Windows Registry unless you are very sure of what you are doing, otherwise you will risk severely damaging your system. • Don’t open your computer or undertake any repair or upgrade work if you are not comfortable with what you are doing. • Read the documentation.
Troubleshooting • Thoroughly check any recent changes you made to your system as these changes may affect one or more system components, or software programs. If possible, go back and undo the change you just made and see if the problem still occurs. • Don’t over complicate things.
Troubleshooting Problems and Possible Solutions Problem Possible Cause - Solution You turned on the power but it doesn’t work. Battery missing / incorrectly installed. Check the battery bay, make sure the battery is present and seated properly (the design of the battery only allows it to go in one way). Make sure there’s nothing interfering with the battery contacts. The battery LED power indicator blinking orange. , is Low Battery. Plug in the DC power source.
Troubleshooting Problem The computer feels too hot. Possible Cause - Solution Make sure the computer is properly ventilated and the Vent/Fan intakes are not blocked. If this doesn’t cool it down, put the system into Hibernate mode or turn it off for an hour. Make sure the computer isn’t sitting on a thermal surface (see “Overheating” on page 1 - 12/1 - 13). Make sure you’re using the correct adapter.
Troubleshooting Problem Possible Cause - Solution You forget the boot password. If you forget the password, you may have to discharge the battery of the CMOS. Contact your service representative for help. Password Warning If you choose to set a boot password, NEVER forget your password. The consequences of this could be serious. If you cannot remember your boot password you must contact your vendor and you may lose all of the information on your hard disk.
Troubleshooting Problem Possible Cause - Solution Other Keyboards If your keyboard is damaged or you just want to make a change, you can use any standard USB keyboard. The system will detect and enable it automatically. However special functions/hot keys unique to the system’s regular keyboard may not work. 8 The system freezes or the screen goes dark. The system’s power saving features have timed-out.
Troubleshooting Problem Possible Cause - Solution The Wireless LAN/Bluetooth modules cannot be configured. The driver(s) for the module(s) have not been installed. Make sure you have installed the driver for the appropriate module (see the instructions for the appropriate module in Chapter 7 "Modules & Options"). A file cannot be copied connected Bluetooth device.
Troubleshooting Resolving the “Insert a SIM” issue with the 3G Module (Windows 8) 1. If a PIN was set for the EM820W 3G module, you have then switched Mobile broadband off (or put the system in Airplane Mode) under Wireless in PC Settings, and the system has just resumed from a power-saving state the following error may occur. 8 Figure 8 - 1 - PC Settings (Charms Bar) - Wireless (Mobile Broadband Off) 2.
Troubleshooting 3. 4. 5. 6. Go to the Charms Bar. Select Settings and you will then note that the WiFi icon will read Unavailable. Standard procedure would be to click the connection and enter the PIN number to unlock the connection. In this instance you will note that the Mobile broadband connection will read Insert a SIM. 8 Figure 8 - 2 - Mobile Broadband (Insert a SIM) 7. 8. 9. In this case you will need to restart the computer.
Troubleshooting 8 8 - 14
Interface (Ports & Jacks) Appendix A: Interface (Ports & Jacks) Overview The following chapter will give a quick description of the interface (ports & jacks) which allow your computer to communicate with external devices, connect to the internet etc.
Interface (Ports & Jacks) Notebook Ports and Jacks Item Description Card Reader Port The card reader allows you to use some of the latest digital storage cards. Push the card into the slot and it will appear as a removable device. DC-In Jack A Plug the supplied AC/DC adapter into this jack to power your computer. HDMI-Out Port The HDMI-Out (High-Definition Multimedia Interface) is an audio/video connector interface for transmitting uncompressed digital streams.
Interface (Ports & Jacks) Item Description Security Lock Slot To prevent possible theft, a Kensington-type lock can be attached to this slot. Locks can be purchased at any computer store. USB 3.0 Ports These USB 3.0 compatible ports (backwards-compatible with USB 2.0 however USB 3.0 will transfer data much faster than USB 2.0) are for low-speed peripherals such as keyboards, mice or scanners, and for high-speed peripherals such as external HDDs, digital video cameras or high-speed scanners etc.
Interface (Ports & Jacks) A A - 4
Control Center Appendix B: Control Center Overview The following chapter will give a quick description of the functions of the Control Center. The Control Center gives quick access to frequently used controls, power management features and enables you to quickly turn modules on/off. Click the Control Center icons to toggle the appropriate function, or hold the mouse button down and move the slider where applicable. Certain functions will automatically be adjusted when a power mode is selected.
Control Center Power Modes You can set a Power Mode by clicking the appropriate icon at the top of the Control Center. Each power mode will affect screen brightness, Touchpad and PC camera power etc. You can click a Control Center icon to set an overall power mode and then click individual icons in the Control Center to power on/off the Touchpad and PC camera.
Control Center Power Status The Power Status icon will show whether you are currently powered by the battery, or by the AC/DC adapter plugged in to a working power outlet. The power status bar will show the current battery charge state. Brightness The Brightness icon will show the current screen brightness level. You can use the slider to adjust the screen brightness or the Fn + F8/F9 key combinations, or use the Fn+ F2 key combination to turn off the LED backlight (press any key to turn it on again).
Control Center Sleep Click the Sleep button to bring up the Hibernate or Sleep buttons, and click either button to have the computer enter the appropriate power-saving mode (see “Power-Saving States” on page 3 - 6). Display Switch Click the Display Switch button to access the menu (or use the priate attached display mode. + P key combination) and select the appro- Time Zone Clicking the Time Zone button will access the Date and Time Windows control panel.
Video Driver Controls Appendix C: Video Driver Controls The basic settings for configuring the LCD are outlined in “Video Features” on page 1 - 31. Make sure you install the drivers in the order indicated in Table 4 - 1, on page 4 - 4. Video (VGA) 1. Insert the Device Drivers & Utilities + User’s Manual disc into an attached DVD drive. 2. Click 2.Install VGA Driver > Yes. 3. Click Next > Yes > Next > Next. 4. Click Finish to restart the computer.
Video Driver Controls Intel® HD Graphics Control Panel Advanced video configuration options are provided by the Intel® HD Control Panel. To access the control panel see below and overleaf: 1. Click the Intel® HD Graphics Control Panel icon in the Start screen.
Video Driver Controls OR 2. Right-click the Desktop and select Graphics Properties from the menu. OR 3. 4. 5. Click Advanced settings in the Screen Resolution control panel in Windows. Click the Intel(R) HD Graphics Control Panel tab and click Graphics Properties (button). Double-click the Intel(R) HD Graphics control panel in the Windows Control Panel.
Video Driver Controls You may make changes to any of the graphics properties by clicking the appropriate menu panel and adjusting the settings on the right.
Video Driver Controls Sub-Menus Some of the menu panels will also have sub-menus (in the top left corner of the menu alongside the icon ) to display further configuration options.
Video Driver Controls Multiple Display Display Click either Display Settings or Color to make display adjustments, including configuration for any attached external displays. At least one other display must be attached in order to view multiple display selection options.
Video Driver Controls Click the Display menu at the top of the screen to display the sub-menus. The Multiple Displays menu allows you to configure the display mode of any attached displays (see “Attaching Other Displays” on page C - 16). Multiple Display At least one other display must be attached in order to view multiple display selection options.
Video Driver Controls The Audio sub-menu allows you to configure the capability mode of any attached displays if applicable (i.e. the attached display supports audio). Enable Audio Without Video to keep audio on when the display blanks out for power saving purposes.
Video Driver Controls 3D This menu allows you to choose how 3D images are displayed. Quality displays the most detail, Balanced provides better computer performance with good quality and Custom allows you to configure the Anisotropic Filtering, Vertical Sync and Anti-Aliasing features to your preferences. Click Apply to save changes.
Video Driver Controls Options Options allows you to Customize Hot Keys (for opening the application, rotating the display, scaling etc.,) to your preferences. Click Apply to save changes.
Video Driver Controls Click the Options menu at the top of the screen to display the sub-menus. The Information Center provides details on System Information, the Built-In Display and any attached displays. Preferences Go to the Preferences sub-menu in Options to configure the preferences for the Intel® HD Graphics Control Panel. Make sure you turn Tray Icon On to display the Intel® HD Graphics Control Panel icon in the notification area of the taskbar (as below).
Video Driver Controls Video The Video Profiles menu allows you to brighten or darken movies, or to switch to vivid colors. Click Basic or Advanced to adjust the video settings based on the Application Settings or Driver Settings. The Preview image will display a sample image using the current settings. You can Save Profile and name the Profile to recall the settings at any time. Click Apply to save changes.
Video Driver Controls Click the Video menu at the top of the screen to display the sub-menus.The Image Enhancement menu allows you to adjust the Sharpness, Skin Tone Enhancement, Noise Reduction etc.Click Apply to save changes.
Video Driver Controls The Image Scaling and Gamut Mapping menus allow you to adjust these items.
Video Driver Controls Display Devices & Options Note that you can use external displays connected to the HDMI-Out port and/or external mini display port. See your display device manual to see which formats are supported. Attaching Displays When you first attach an external display you may find that the desktop does not occupy the full screen area. Use either the display’s auto adjust/configure controls, or the Intel(R) HD Graphics Control Panel to configure the full screen display.
Video Driver Controls Multiple Display At least one other display must be attached in order to view Multiple Display selection options. Attaching Other Displays To Clone Displays: 1. 2. 3. 4. 5. Attach your external display to the HDMI-Out port/mini display port, and turn it on. Go to the Intel(R) HD Graphics Control Panel control panel and click Display > Multiple Displays (sub-menu). Click Clone from the Select Multiple Display Mode menu. Click Apply, and OK to confirm the settings change.
Video Driver Controls To Enable Extended Mode: 1. 2. 3. 4. Attach your external display to the HDMI-Out port/mini display port, and turn it on. Go to the Intel(R) HD Graphics Control Panel control panel and click Display > Multiple Displays (sub-menu). Click Extended from the Select Multiple Display Mode menu. Click Apply, and OK to confirm the settings change. Click the appropriate monitor icon and drag it to match the physical arrangement you wish to use (e.g.
Video Driver Controls Windows Logo Key + P Key Combination You can use the +P key combination to quickly bring up the Second Screen menu. Attaching Other Displays - Devices (Charms Bar) You can configure attached displays from Devices (in the Windows 8 Charms Bar). 1. 2. 3. 4. Attach your external display to the HDMI-Out port/mini display port, and turn it on. Go the Charms Bar and select Devices. Click Second Screen.
Video Driver Controls Configuring an External Display In Windows 1. 2. 3. 4. Attach your external display to the HDMI-Out port/mini display port, and turn it on. Go to the Screen resolution control panel in the Desktop app. Click the Detect button. The computer will then detect any attached displays.
Video Driver Controls 5. You can configure the displays from the Multiple Displays menu. Figure C - 18 Screen Resolution Multiple Display Options C • Duplicate these displays - Shows an exact copy of the main display desktop on the other display(s) • Extend these displays - Treats both connected displays as separate devices • Show desktop only on 1/2 - Only one of your displays is used.
Video Driver Controls HDMI Audio Configuration HDMI (High-Definition Multimedia Interface) carries both audio and video signals. In some cases it will be necessary to go to the Sound control panel and manually configure the HDMI audio output as per the instructions below. 1. 2. 3. 4. Go to the Control Panel.
Video Driver Controls 5. 6. Adjust the HDMI settings from the control panel tabs. Click/tap OK to close the Sound control panel.
Video Driver Controls HDMI Notes • Connect a device with HDMI support to the HDMI-Out port BEFORE attempting to play audio/video sources through the device. • To play audio sources through your external display’s (TV or LCD) speakers you will need to go to the audio configuration control panel on the display and configure the audio input accordingly (see your display device manual). HDMI Video Configuration 1. 2. 3. 4. Connect an HDMI cable from the HDMI-Out port to your external display.
Video Driver Controls C C - 24
Specifications Appendix D: Specifications Latest Specification Information The specifications listed in this Appendix are correct at the time of going to press. Certain items (particularly processor types/ speeds and CD/DVD device types) may be changed, updated or delayed due to the manufacturer's release schedule. Check with your distributor/supplier for details.
Specifications Processors Video Adapter Keyboard & Pointing Device Intel® Core™ i7-4500U processor (22nm, 1.80GHz, DDR3L-1600MHz, 4MB L3 cache, TDP: 15W) Intel® HD Graphics (GPU is Dependent on Processor): Dynamic Frequency Intel Dynamic Video Memory Technology up to 1.7MB Microsoft DirectX®11 Compatible Built-in Touchpad with Multi-Gesture Functionality Intel® Core™ i5-4200U processor (22nm, 1.60GHz, DDR3L-1600MHz, 3MB L3 cache, TDP: 15W) Intel® Core™ i3-4010U processor (22nm, 1.
Specifications Mini Card Slots Slot 1 for Half Size Mini-Card WLAN Combo Module with PCIe & USB Interfaces Slot 2 for Full Size Mini-Card 3G Module with USB Interface OR Full Size MiniCard SSD (Solid State Drive) with SATA Interface Communication Built-In 10/100/1000Mb Base-TX Ethernet LAN 1.0M HD Video Camera Module with USB interface Intel® Dual Band Wireless-AC 7260 (2*2 802.11 a/c) Half Mini-Card PCIe WLAN + Bluetooth Combo Module (Factory Option) Intel® Dual Band Wireless-N 7260 (2*2 802.
Specifications Features Painted Style (For some Model designs in this series) Intel® Rapid Start Technology Intel® Smart Response Technology (processor dependent) Intel® Anti-Theft Technology Intel® Identity Protection Technology Intel® Smart Connect Technology Operating System Windows® 8 (64-bit) Environmental Spec Temperature Operating: Non-Operating: Relative Humidity Operating: Non-Operating: 5°C - 35°C -20°C - 60°C 20% - 80% 10% - 90% Dimensions & Weight D 340mm(w) * 240mm(d) * 22.8mm(h) 2.
