Preface Notice The company reserves the right to revise this publication or to change its contents without notice. Information contained herein is for reference only and does not constitute a commitment on the part of the manufacturer or any subsequent vendor. They assume no responsibility or liability for any errors or inaccuracies that may appear in this publication nor are they in anyway responsible for any loss or damage resulting from the use (or misuse) of this publication.
Preface FCC Statement (Federal Communications Commission) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Preface IMPORTANT SAFETY INSTRUCTIONS Follow basic safety precautions, including those listed below, to reduce the risk of fire, electric shock, and injury to persons when using any electrical equipment: 1. 2. 3. 4. 5. Do not use this product near water, for example near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool. Avoid using this equipment with a telephone line (other than a cordless type) during an electrical storm.
Preface Instructions for Care and Operation The notebook computer is quite rugged, but it can be damaged. To prevent this, follow these suggestions: 1. Don’t drop it, or expose it to shock. If the computer falls, the case and the components could be damaged. Do not expose the computer to any shock or vibration. 2. Do not place anything heavy on the computer. Keep it dry, and don’t overheat it. Keep the computer and power supply away from any kind of heating element. This is an electrical appliance.
Preface 3. Avoid interference. Keep the computer away from high capacity transformers, electric motors, and other strong magnetic fields. These can hinder proper performance and damage your data. 4. Follow the proper working procedures for the computer. Shut the computer down properly and don’t forget to save your work. Remember to periodically save your data as data may be lost if the battery is depleted. Do not turn off the power until you properly shut down all programs. 5.
Preface Power Safety The computer has specific power requirements: Power Safety Warning Before you undertake any upgrade procedures, make sure that you have turned off the power, and disconnected all peripherals and cables (including telephone lines). It is advisable to also remove your battery in order to prevent accidentally turning the machine on. VI • Only use a power adapter approved for use with this computer.
Preface Battery Precautions • • • • • • • • • Only use batteries designed for this computer. The wrong battery type may explode, leak or damage the computer. Do not remove any batteries from the computer while it is powered on. Do not continue to use a battery that has been dropped, or that appears damaged (e.g. bent or twisted) in any way. Even if the computer continues to work with a damaged battery in place, it may cause circuit damage, which may possibly result in fire.
Preface Cleaning Do not apply cleaner directly to the computer; use a soft clean cloth. Do not use volatile (petroleum distillates) or abrasive cleaners on any part of the computer. Servicing Do not attempt to service the computer yourself. Doing so may violate your warranty and expose you and the computer to electric shock. Refer all servicing to authorized service personnel. Unplug the computer from the power supply.
Preface Travel Considerations Packing As you get ready for your trip, run through this list to make sure the system is ready to go: 1. 2. 3. 4. 5. 6. 7. 8. Check that the battery pack and any spares are fully charged. Power off the computer and peripherals. Close the display panel and make sure it’s latched. Disconnect the AC adapter and cables. Stow them in the carrying bag. The AC adapter uses voltages from 100 to 240 volts so you won’t need a second voltage adapter.
Preface On the Road In addition to the general safety and maintenance suggestions in this preface, and “Troubleshooting” on page 8 - 1, keep these points in mind: Hand-carry the notebook - For security, don’t let it out of your sight. In some areas, computer theft is very common. Don’t check it with “normal” luggage. Baggage handlers may not be sufficiently careful. Avoid knocking the computer against hard objects.
Preface Developing Good Work Habits Developing good work habits is important if you need to work in front of the computer for long periods of time. Improper work habits can result in discomfort or serious injury from repetitive strain to your hands, wrists or other joints. The following are some tips to reduce the strain: • Adjust the height of the chair and/or desk so that the keyboard is at or slightly below the level of your elbow. Keep your forearms, wrists, and hands in a relaxed position.
Preface Lighting Proper lighting and comfortable display viewing angle can reduce eye strain and muscle fatigue in your neck and shoulders. • Position the display to avoid glare or reflections from overhead lighting or outside sources of light. • Keep the display screen clean and set the brightness and contrast to levels that allow you to see the screen clearly. • Position the display directly in front of you at a comfortable viewing distance. • Adjust the display-viewing angle to find the best position.
Preface Contents Notice ...........................................................................I FCC Statement ...................................................II Instructions for Care and Operation ................. IV Power Safety ..................................................... VI Battery Precautions ..........................................VII Cleaning ........................................................ VIII Servicing ........................................................
Preface Inserting and Removing PC Cards .........................2-8 Auto Mail Checker ...................................................2-9 TouchPad and Buttons/Mouse ...............................2-11 Audio Features .......................................................2-12 Audio "DJ" CD Player ...........................................2-13 Configuring the Infrared Settings for FIR ..............2-15 Adding a Printer .....................................................2-16 USB Printer ...............
Preface Auto Mail Checker (WinXP) ..............................4-11 LCDAP (WinXP) ................................................4-12 Module Drivers ......................................................4-12 Wireless LAN (WinXP) ......................................4-12 Bluetooth (WinXP) .............................................4-12 TV Tuner (WinXP) .............................................4-12 PC Camera (WinXP) ...........................................4-12 BIOS Utilities Overview ............
Preface ZCOM (802.11a/b/g) WLAN Module Driver Installation ........................................................................7-4 The Bluetooth Module .............................................7-5 Bluetooth Module Driver Installation ...................7-5 The 7-in-1 Card Reader Module ..............................7-7 The TV Tuner Module .............................................7-8 Installing the AverTV Utility Software ................7-9 Installing the InterVideo WinDVD 4 Software ....
Preface NVIDIA Video Driver Controls Specifications NVIDIA Video Driver Installation .........................B-1 NVIDIA Display Properties ....................................B-2 Display Devices .......................................................B-6 Attaching Other Displays ........................................B-7 Display Modes ......................................................... B-9 Enabling TV Display .............................................B-10 Processor Types ......................
Preface XVIII
Quick Start Guide Chapter 1: Quick Start Guide Overview This Quick Start Guide is a brief introduction to the basic features of your computer, to navigating around the computer and to getting your system started.
1 Quick Start Guide Advanced Users If you are an advanced user you may skip over most of this Quick Start Guide. However you may find it useful to refer to “What to Install” on page 4 - 1, “BIOS Utilities” on page 5 - 1 and “Upgrading The Computer” on page 6 - 1 in the User’s Manual. You may also find the notes marked with a of interest to you. Notes Check the light colored boxes with the mark above to find detailed information about the computer’s features.
Quick Start Guide System Software Your computer may already come with system software pre-installed.
1 Quick Start Guide System Startup 1. 2. 3. 4. 5. 6. 7. Remove all packing materials. Place the computer on a stable surface. Securely attach any peripherals you want to use with the notebook (e.g. keyboard and mouse) to their ports. Attach the AC adapter to the DC-In jack on the right of the computer, then plug the AC power cord into an outlet, and connect the AC power cord to the AC adapter. Move and hold the LCD latches 1 outwards, and the release the top cover.
Quick Start Guide Getting to Know Your Computer The graphics on the following pages will help you to become familiar with the basic functions, and to learn the location of the various ports and components of your computer. Model Differences 1 Model A Standard Screen Model B Wide Screen 1 1 1. This manual refers to the two notebook models pictured on this page. The designs vary slightly in external design. Photographs used throughout this manual are of Model A (Model B features a wide screen).
1 Quick Start Guide 1.8" LCD The 1.8" TFT Top Case LCD can be used to display company logos, personal photos, animated files etc. (see below). Details on how to program the logos and pictures for the 1.8" LCD are available in Appendix D on page D - 1. 1.8" LCD Power ON/OFF Power to the 1.8" LCD may be toggled on/off by touching the metal rim which runs around the LCD. The 1.
Quick Start Guide System Map: Top View with LCD Panel Open 1 1. Optional Built-In PC Camera 2. LCD 3. Speakers (Model A -See Figure 1 - 2) 4. LED Indicators 5. AP-key Buttons 6. Power Button 7. Built-In Microphone 8. Keyboard 9. TouchPad & Buttons 10. Audio "DJ" Display Panel (Including LED Indicators) Wireless Device Operation Aboard Aircraft The use of any portable electronic transmission devices aboard aircraft is usually prohibited.
1 Quick Start Guide LED Indicators Table 1 - 2 - Audio "DJ" LED Indicators The two sets of indicators on the computer display helpful information about the current status of the computer. There are also indicators located on the display panel of the Audio "DJ".
Quick Start Guide AP-key Buttons Function Keys & Numeric Keypad These buttons access the internet, e-mail and toggle power to the optional PC Camera, Wireless LAN and/ or Bluetooth modules. Make sure you install the driver to enable the AP-key Button functions (refer to “What to Install” on page 4 - 1). The keyboard has an embedded numerical keypad for easy numeric data input (see Figure 1 - 5).
1 Quick Start Guide Keys Description Fn Function Key Fn + F3 Mute Toggle Fn + F4 Sleep Toggle Fn + F5 Decrease Audio Volume Fn + F6 Increase Audio Volume Fn + F7 Display Toggle Fn + F8 Decrease LCD Brightness Fn + F9 Increase LCD Brightness Fn + NumLk Number Lock Toggle Fn + ScrLk Scroll Lock Toggle Table 1 - 4 - Function Keys Figure 1 - 5 - Keyboard Function Keys NumLk & ScrLk Keys Numeric Keypad Fn Key Special Characters Some software applications allow the number-keys to be
Quick Start Guide System Map: Front & Rear Views 4 1 2 1 2 3 Figure 1 - 6 Front & Rear Views 4 1. 2. 5 3. 4. 5. Audio "DJ" Player The built-in standalone audio CD player gives you direct hardware control for audio CDs (MP3 compatible) when the computer is shut down, but has a working power source. 6 7 8 9 10 11 12 13 Overheating 6. 7. 8. 9. 10. 11. 12. 13.
1 Quick Start Guide System Map: Left View Figure 1 - 7 Left View 1. 2. 3. 4. 5. 6. 7. 3-in-1 Card Reader Infrared Transceiver (see page 2 - 12) Speaker Secondary Device Bay Release Latch Secondary (Optional) Device Bay RJ-45 LAN Jack PC Card Slot 1 3 6 7 3-in-1 Card Reader Formats The card reader allows you to use the most popular digital storage card formats (see below).
Quick Start Guide System Map: Right View Figure 1 - 8 - Right View 1. 1 6 7 2 3 4 5 Changing DVD Regional Codes Go to the Control Panel and double-click System > Hardware (tab), click Device Manager, then click the + next to DVD/CD-ROM drives. Double-click on the DVD-ROM device to bring up the Properties box, and select the DVD Region (tab) to bring up the control panel to allow you to adjust the regional code (see “DVD Regional Codes” on page 2 - 5).
1 Quick Start Guide System Map: Bottom View Figure 1 - 9 Bottom View 1. 2. 3. 4. 5. 6. Battery Speakers Hard Disk Bay/TV Tuner Cover Video Card Cover CPU Cover Vent/Fan Intake 5 4 CPU 6 The CPU is not a user serviceable part. Opening this compartment, or accessing the CPU in any way, may violate your warranty. 6 6 6 3 2 1 2 Battery Information Always completely discharge, then fully charge, a new battery before using it.
Quick Start Guide Windows XP Start Menu & Control Panel Most of the control panels, utilities and programs within Windows XP (and most other Windows versions) are accessed from the Start menu. When you install programs and utilities they will be installed on your hard disk drive, and a shortcut will usually be placed in the Start menu and/or the desktop. You can customize the look of the Start menu by right-clicking the Start menu and selecting Properties from the menu.
1 Quick Start Guide Video Features Video Driver Controls This computer features two different (NVIDIA GeForce 6800 or ATI M28) PCI Express video card options (see “Video Card Options” on page D - 3). If you are unsure which video card your model features, then go to the BIOS and check “VGA Card:” under System Information in the Advanced menu (see “System Information (Advanced Menu)” on page 5 - 8).
Quick Start Guide NVIDIA Display Properties 1 2 3 ATI Display Properties 1 2 3 Figure 1 - 11 - Display Properties Desktop Video Features 1 - 17 1
1 Quick Start Guide Display Devices & Options Besides the built-in LCD, you can also use an external VGA monitor/external Flat Panel Display or TV as your display device. A VGA monitor/Flat Panel Display connects to the DVI-Out port, a TV to the S-Video-Out Port. The following display modes are available (see“NVIDIA Video Driver Controls” on page B - 1 or “ATI Video Driver Controls” on page C - 1 for details).
Quick Start Guide Power Management Features The Power Options control panel in Windows (see page 1 - 14) allows you to configure power management features for your computer. You may conserve power through individual components such as the monitor or hard disk (by means of Power Schemes), or you may use either Standby or Hibernate mode to conserve power throughout the system (enable Hibernate support from the control panel as pictured in Figure 1 - 12).
1 Concise User’s Guide 1 - 20
Storage Devices, Mail Program, Mouse, Audio & Printer Chapter 2: Storage Devices, Mail Program, Mouse, Audio & Printer Overview Read this chapter to learn more about the following main features and components of the computer: • • • • • • • • • • Hard Disk Drive Optical Device 3-in-1 Card Reader PC Card Slot Auto Mail Checker TouchPad and Buttons/Mouse Audio Features Audio "DJ" CD Player Configuring the Infrared Settings for FIR Adding a Printer Overview 2 - 1 2
Storage Devices, Mail Program, Mouse, Audio & Printer 2 Power Safety Before attempting to access any of the internal components of your computer please ensure that the machine is not connected to the AC power, and that the machine is turned off and any batteries are removed. Also ensure that all peripheral cables, including phone lines, are disconnected from the computer.
Storage Devices, Mail Program, Mouse, Audio & Printer Optical Device There is a bay for a 5.25" optical (Combo or DVD-Dual) device (12.7mm height). The actual device will depend on the model you purchased. The optical device is usually labeled “Drive D:” and may be used as a boot device if properly set in the BIOS (see “Boot Menu” on page 5 - 13).
Storage Devices, Mail Program, Mouse, Audio & Printer 2 CD Emergency Eject If you need to manually eject a CD (e.g. due to an unexpected power interruption) you may push the end of a straightened paper clip into the emergency eject hole. However please do NOT use a sharpened pencil or similar object that may break and become lodged in the hole. Disk Eject Warning Don’t try to remove a CD/DVD while the system is accessing it. This may cause the system to “crash”.
Storage Devices, Mail Program, Mouse, Audio & Printer DVD Regional Codes 2 To change the DVD regional codes see “Changing DVD Regional Codes” on page 1 - 13. .
Storage Devices, Mail Program, Mouse, Audio & Printer 2 Card Reader Cover Make sure you keep the cover in the card reader when not is use. This will help prevent foreign objects and/or dust getting in to the card reader. 3-in-1 Card Reader The card reader allows you to use some of the latest digital storage cards. Push the card into the slot and it will appear as a removable device.
Storage Devices, Mail Program, Mouse, Audio & Printer Removing Cards from the Card Reader 2 To remove any inserted cards, click the Safely Remove Hardware icon in the Windows taskbar and follow the instructions below in order to prevent system errors (DO NOT PULL THE CARD OUT OF THE SLOT). 1. 2. Click the icon in the taskbar, and click to select the card from the pop-up list. A “’Safe To Remove Hardware” bubble will pop-up to indicate you may now safely remove the card from the reader slot.
Storage Devices, Mail Program, Mouse, Audio & Printer PC Card Slot 2 The computer is equipped with a PCMCIA 3.3V/5V slot for one type II PC Card. Make sure you install the driver for the PC Card (see “What to Install” on page 4 - 1). Inserting and Removing PC Cards • Align the PC Card with the slot and push it in until it locks into place. • To remove a PC Card, simply press the eject button 1 next to the slot.
Storage Devices, Mail Program, Mouse, Audio & Printer Auto Mail Checker 2 After you have installed the driver for the Auto Mail Checker program (see “What to Install” on page 4 - 1) you may then configure it to give you notification when you receive new mail. You must be online to receive this notification (note that this program only supports the POP3 protocol), and your default mail program does not need to be open.
Storage Devices, Mail Program, Mouse, Audio & Printer 2 You may then configure the options for your mailserver, name, password, program and method(s) of notification. Note Check with your Internet Service Provider, network administrator or Mail Service provider for details on what to put on these pages.
Storage Devices, Mail Program, Mouse, Audio & Printer TouchPad and Buttons/Mouse The TouchPad is an alternative to the mouse; however, you can also add a mouse to your computer through one of the USB ports. The TouchPad buttons function in much the same way as a two-button mouse. The central button may be configured to function as you require.
Storage Devices, Mail Program, Mouse, Audio & Printer 2 Sound Volume Adjustment How high the sound volume can be set using the volume control knob depends on the setting of the volume control within Windows. Click the Speaker icon on the taskbar to check the setting.
Storage Devices, Mail Program, Mouse, Audio & Printer Audio "DJ" CD Player The built-in standalone audio CD player gives you direct hardware control for audio CDs/DVDs when the computer is shut down, but has a working power source. 1. Make sure that the computer is shut down (i.e. the operating system is not running) but you have a working power source (either battery or AC Power). 2. Press the Audio "DJ" power button. 3.
Storage Devices, Mail Program, Mouse, Audio & Printer 2 TV Tuner Option If you have included the optional TV Tuner in your purchase configuration, you can use the supplied remote control unit to control the Audio "DJ". Figure 2 - 12 Audio "DJ" Controls 2 - 14 Audio "DJ" CD Player 1 4 2 3 5 1. 2. 3. 4. 5. 6. 7. 8. 9. 10.
Storage Devices, Mail Program, Mouse, Audio & Printer Configuring the Infrared Settings for FIR To configure your computer for Fast Infrared (FIR) communication follow these steps: 1. 2. 3. 4. 5. Click Start, point to Settings and click Control Panel (or click Start > Control Panel). Double-click Wireless Link (Printers and Other Hardware Category) icon. Click Hardware (tab), and click the Properties button, then click the Advanced (tab).
Storage Devices, Mail Program, Mouse, Audio & Printer 2 Parallel Printer After setting up the printer attach the parallel cable to the printer. Connect the printer’s parallel cable to the Parallel port. Adding a Printer The most commonly used peripheral is a printer. The following conventions will help you to add a printer, however it is always best to refer to the printer manual for specific instructions and configuration options. USB Printer Most new printers have a USB interface connection.
Power Management Chapter 3: Power Management Overview To conserve power, especially when using the battery, your computer uses the ACPI power management system. Power management conserves power by controlling individual components of the computer (the monitor and hard disk drive) or the whole system. This chapter covers: • • • • • • OS Note Power management functions will vary slightly depending on your operating system.
Power Management 3 2nd Battery If you have included the secondary battery in your purchase configuration, do not try to startup the computer from the 2nd battery only. The Power Sources The computer can be powered by either an AC adapter or a battery pack. AC Adapter Use only the AC adapter that comes with your computer. The wrong type of AC adapter will damage the computer and its components. 1. 2. 3. 4. Attach the AC adapter to the DC-in jack on the right of the computer.
Power Management Turning on the Computer Now you are ready to begin using your computer. To turn it on simply press the power button on the front panel. When the computer is on, you can use the power button as a Standby/Hibernate/Shutdown hot-key button when it is pressed for less than 4 seconds (pressing and holding the power button for longer than this will shut the computer down). Use Power Options in the Windows control panel to configure this feature.
Power Management 3 Resuming Operation The system can resume from Monitor or Hard Disk Standby by pressing a key on the keyboard. Figure 3 - 1 Power Schemes 3 - 4 Power Schemes Power Schemes You can set your computer to conserve power through individual components by means of Power Schemes.
Power Management Each Windows Power Scheme will also adjust the processor performance of your machine in order to save power. This is worth bearing in mind if you are experiencing any reduced performance (especially under DC/battery power). 3 Choose the Home/Office Desk scheme for maximum performance when the computer is powered from an AC power source.
Power Management System Power Options 3 You can use the system power options to stop the computer’s operation and restart where you left off. This system features Standby and Hibernate sleep mode levels (Hibernate mode will need to be enabled by clicking the option in the Hibernate tab in the Power Options control panel - Figure 3 - 2 on page 3 - 7). Hibernate Mode vs. Shutdown Hibernate mode and Shutdown are the same in that the system is off and you need to press the power button to turn it on.
Power Management Standby Standby saves the least amount of power, but takes the shortest time to return to full operation. During Standby the hard disk is turned off, and the CPU is made to idle at its slowest speed. All open applications are retained in memory. When you are not using your computer for a certain length of time, which you specify in the operating system, it will enter Standby mode to save power.
Power Management Configuring the Power Button The power button may be set to send the computer in to either Standby or Hibernate mode (Figure 3 - 3). In Standby mode, the LED will flash green. In Hibernate mode the LED will be off. If you are in a power saving mode set to save power through individual components (e.g. hard disk, monitor), the LED will remain green.
Power Management Battery Information Please follow these simple guidelines to get the best use out of your battery. Low Battery Warning New Battery Always completely discharge, then fully charge, a new battery (see “Battery FAQ” on page 3 - 12 for instructions on how to do this). Battery Life Your computer’s battery life is dependent upon many factors, including the programs you are running, and peripheral devices attached.
Power Management 3 Conserving Battery Power To conserve battery power: Battery life may be shortened through improper maintenance. To optimize the life and improve its performance, fully discharge and recharge the battery at least once every 30 days. We recommend that you do not remove the primary battery yourself. If you do need to remove the battery for any reason see “Removing the Primary Battery” on page 6 - 3. Lower the brightness level of the LCD display.
Power Management Proper Handling of the Battery Pack • DO NOT disassemble the battery pack under any circumstances • DO NOT expose the battery to fire or high temperatures, it may explode • DO NOT connect the metal terminals (+, -) to each other Damaged Battery Warning Should you notice any physical defects (e.g. the battery is bent out of shape after being dropped), or any unusual smells emanating from the notebook battery, shut your computer down immediately and contact your service center.
Power Management 3 Caution Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Discard used battery according to the manufacturer’s instructions. Battery FAQ How do I completely discharge the battery? Use the computer with battery power until it shuts down due to a low battery.
Drivers & Utilities Chapter 4: Drivers & Utilities This chapter deals with installing the drivers and utilities essential to the operation or improvement of some of the computer’s subsystems. The system takes advantage of some newer hardware components for which the latest versions of most available operating systems haven’t built in drivers and utilities. Thus, some of the system components won’t be auto-configured with an appropriate driver or utility during operating system installation.
Drivers & Utilities Navigate (Browse..) to D: 4 You will notice that many of the instructions for driver installation require you to “Navigate (Browse) to D:”. We assume that you will install all drivers and utilities from the built-in CD device and it is assigned to “Drive D:”. In addition, all file extensions can be seen In this case “D:” is the drive specified for your CD device. Not all computers are setup the same way, and some computers have the CD listed under a different drive letter - e.g.
Drivers & Utilities Service Packs Make sure you have installed the appropriate Service Pack before installing all the drivers. If you are unsure of the Service Pack currently installed see below. Service Pack Installed To see which Service Pack is currently installed on your computer go to the General tab of the System control panel. Right-click the My Computer icon on the desktop or in the Start menu and select Properties.
Drivers & Utilities Authorized Driver Message 4 If you receive a message telling you that the driver you are installing is not authorized (Digital Signature Not Found), just click Continue Anyway to ignore the message and continue the installation procedure. You will receive this message in cases where the driver has been released after the version of Windows you are currently using. All the drivers provided will have already received certification for Windows.
Drivers & Utilities Driver Installation Insert the Device Drivers & Utilities + User’s Manual CD-ROM and the Notebook Driver Installation application will run automatically. If you want to install the driver manually see “Manual Driver Installation” on page 4 - 6. 1. 2. 3. 4. 5. 6. Check the driver installation order from Table 4 1, on page 4 - 6 (the drivers must be installed in this order) which is the same as that listed in the driver installation screen menu.
Drivers & Utilities Manual Driver Installation If you wish to install the drivers manually, click the Exit button to quit the Notebook Driver Installation application, then follow the manual installation procedure for each driver. The manual installation procedure begins with instructions on how to browse to the executable file; “Click Start (menu) > Run..”.
Drivers & Utilities Windows XP Drivers This section covers driver and utility installation instructions for Windows XP (Professional & Home). New Hardware Found If you see the message “New Hardware Found” (Found New Hardware Wizard) during the installation procedure (other than when outlined in the driver install procedure), click Cancel to close the window, and follow the installation procedure.
Drivers & Utilities 4 Audio (WinXP) 1. Run the Notebook Driver Installation application and double-click Audio. OR Click Start (menu) > Run... and navigate (Browse..) to D:\Drivers\ 02AUDIO\Setup.exe and click OK. 2. Click Next (click Cancel if The Found New Hardware Wizard appears). 3. Click Finish to restart the computer. 4. When the computer restarts click Cancel if the The Found New Hardware Wizard appears. 5.
Drivers & Utilities LAN (WinXP) 1. Run the Notebook Driver Installation application and double-click Lan. OR Click Start (menu) > Run... and navigate (Browse..) to D:\Drivers\ 04LAN\WinXP\SetupYukonWin.exe and click OK. 2. Click Next. 3. Click the button to accept the license and click Next. 4. Click Next > Install > Finish. 5. The network settings can now be configured.
Drivers & Utilities 4 AP-Key Buttons (WinXP) 1. Run the Notebook Driver Installation application and double-click AP-key. OR Click Start (menu) > Run... and navigate (Browse..) to D:\Drivers\ 06APKey\Setup.exe and click OK. 2. Click Next. 3. Click Finish to restart the computer. 4 - 10 Windows XP Drivers TouchPad (WinXP) 1. Run the Notebook Driver Installation application and double-click Touchpad. OR Click Start (menu) > Run... and navigate (Browse...) to D:\Drivers\ 07TOUCHPAD\WINXP\Setup.
Drivers & Utilities PCMCIA & Card Reader (WinXP) 1. Run the Notebook Driver Installation application and double-click PCMCIA. OR Click Start (menu) > Run... and navigate (Browse...) to D:\Drivers\ 08PCMCIA\setup.exe and click OK. 2. Choose the language you prefer, and click OK. 3. Click Next > Finish. Auto Mail Checker (WinXP) 1. Run the Notebook Driver Installation application and double-click Automail. OR Click Start (menu) > Run... and navigate (Browse..) to D:\Drivers\ 09AUTOMAIL\SETUP.
Drivers & Utilities 4 LCDAP (WinXP) 1. Run the Notebook Driver Installation application and double-click LCDAP. OR Click Start (menu) > Run... and navigate (Browse..) to D:\Drivers\ 10LCDAP\LCDAP.exe and click OK. 2. This will run the program (see “1.8" Top Case LCD” on page D - 1 for further instructions). 3. If you wish to copy the application to the hard disk make sure you copy the whole LCDAP folder to your hard disk (e.g. C: drive).
BIOS Utilities Chapter 5: BIOS Utilities Overview This chapter gives a brief introduction to the computer’s built-in software: Diagnostics: The POST (Power-On Self Test) Configuration: The Setup utility If your computer has never been set up, or you are making important changes to the system (e.g. hard disk setup), then you should review this chapter first and note the original settings found in Setup. Even if you are a beginner, keep a record of the settings you find and any changes you make.
BIOS Utilities POST Screen 5 1.BIOS information 2.CPU type 3.Memory status 4.Enter Setup prompt appears only during POST Note: The POST screen as pictured is for guideline purposes only. The POST screen on your computer may appear slightly different. Figure 5 - 1 POST Screen The Power-On Self Test (POST) Each time you turn on the computer, the system takes a few seconds to conduct a POST, including a quick test of the on-board RAM (memory).
BIOS Utilities Failing the POST Errors can be detected during the POST. There are two categories, “fatal” and “non-fatal”. Fatal Errors These stop the boot process and usually indicate there is something seriously wrong with your system. Take the computer to your service representative or authorized service center as soon as possible. Non-Fatal Errors This kind of error still allows you to boot.
BIOS Utilities The Setup Program The Phoenix Setup program tells the system how to configure itself and manage basic features and subsystems (e.g. port configuration). Entering Setup 5 To enter Setup, turn on the computer and press F2 during the POST. The prompt (Press F2 to Enter Setup) seen in Figure 5 - 1 is usually present for a few seconds after you turn on the system. If you get a “Keyboard Error”, (usually because you pressed F2 too quickly) just press F2 again.
BIOS Utilities Setup Screens The following pages contain additional advice on portions of the Setup. Setup Menus Along the top of the screen is a menu bar with five (5) menu headings. When you select a heading, a new screen appears. Scroll through the features listed on each screen to make changes to Setup. Instructions on how to navigate each screen are in the box along the bottom of the screen.
BIOS Utilities Main Menu PhoenixBIOS Setup Utility Figure 5 - 2 Main Main Advanced Security Boot Exit Main Menu Item Specific Help System Time: 13 [22:11:05] [09/22/2004] System Date: 5 IDE Channel 0 Master IDE Channel 0 Slave [CD-ROM] [None] SATA Port 1 SATA Port 2 [60012MB SATA1] [None] Installed memory Available to OS Used by devices F1 Esc Help Exit , , or selects field.
BIOS Utilities IDE Channel 0 Master/Slave Pressing Enter here opens the sub-menu to show the configuration of either a CD/DVD type Device or HDD on the computer’s IDE Channel 0. Use the Auto (Type:) setting to have the items configured automatically for you. SATA Port 1/2 Pressing Enter here opens the sub-menu to show the configuration of any hard disks on the computer’s SATA Port 1 or 2. Use the Auto (Type:) setting to have the items configured automatically for you.
BIOS Utilities Advanced Menu Figure 5 - 3 Advanced Menu PhoenixBIOS Setup Utility Advanced Advanced Main Security Power Boot Setup Warning Setting items on this menu to incorrect values may cause your system to malfunction.
BIOS Utilities I/O Device Configuration The sub-menus under this item include options to configure the Serial port A (Serial Mouse), Serial port B (Infrared) and Parallel (Printer) port. These can be left to the default settings, however you may wish to use certain devices that require settings to be adjusted accordingly. Check the documentation for any such devices to see what settings are required.
BIOS Utilities Reset Configuration Data: This item is set to No as default. You can change the setting to Yes if you have installed a new add-on which has reconfigured the system, resulting in such a serious system conflict that the operating system is unable to boot.
BIOS Utilities Security Menu Figure 5 - 5 PhoenixBIOS Setup Utility Main Advanced Security Security Boot Security Menu Exit Item Specific Help Supervisor Password Is: Clear Set Supervisor Password [Enter] Password on boot: [Disabled] Supervisor Password controls access to the setup utility.
BIOS Utilities Password Warning 5 If you set a boot password (Password on boot is “Enabled“), NEVER forget your password. The consequences of this could be serious. If you cannot remember your boot password you must contact your vendor and you may lose all of the information on your hard disk. 5 - 12 Security Menu Password on boot: Specify whether or not a password (supervisor or user password) should be entered to boot the computer.
BIOS Utilities Boot Menu Figure 5 - 6 Boot Menu PhoenixBIOS Setup Utility Main Advanced Security Boot Exit Item Specific Help Boot priority order: 1: USB FDC: 2: Legacy Floppy Drives 3: SATA_1: FUJITSU MHT2060AT-(S1) 4: SATA_2: 5: IDE0_M: TSSTcorpCD/DVDW TS-L532A6: IDE0_S: 7: PCI LAN: B2 D0 Yukon PXE 8: Excluded from boot order: F1 Esc Help Exit Select Item Select Menu -/+ Enter Keys used to view or configure devices: Up and Down arrows select a device.
BIOS Utilities Boot devices usually are hard drives, floppy drives, and CD/DVD-ROMs and networks (LAN). When you specify a device as a boot device on the Boot Menu, it requires the availability of an operating system on that device. Most home computers come with an operating system already installed on “Drive C:”. 5 If you wish to boot from a CD/DVD-ROM you will need to add it to the boot order. As a general rule the order below is recommended: 1. 2. 3. 4.
BIOS Utilities Exit Menu Figure 5 - 7 PhoenixBIOS Setup Utility Main Advanced Security Boot Exit Menu Exit Exit Item Specific Help Exit Saving Changes Exit Discarding Changes Load Setup Defaults Discard Changes Save Changes F1 Esc Help Exit Select Item Select Menu Exit System Setup and save your changes to CMOS.
BIOS Utilities 5 5 - 16
Upgrading The Computer Chapter 6: Upgrading The Computer Overview This chapter contains information on upgrading the computer. Follow the steps outlined to make the desired upgrades. If you have any trouble or problems you can contact your service representative for further help.
Upgrading The Computer Power Safety Warning 6 Before you undertake any upgrade procedures, make sure that you have turned off the power, and disconnected all peripherals and cables (including telephone lines). It is advisable to also remove your battery in order to prevent accidentally turning the machine on. When Not to Upgrade These procedures involve opening the system’s case, adding and sometimes replacing parts.
Upgrading The Computer Removing the Primary Battery If you are confident in undertaking upgrade procedures yourself, for safety reasons it is best to remove the battery (batteries). Warranty Warning 1. 2. 3. 4. 5. Please check with your service representative before undertaking any upgrade procedures to find out if this will VOID your warranty. Turn the computer off, and turn it over. Move the battery release latches in the direction of the arrows 1 - 2 . The battery will pop -up.
Upgrading The Computer HDD System Warning 6 New HDD’s are blank. Before you begin make sure: You have backed up any data you want to keep from your old HDD. You have all the CDROMs and FDDs required to install your operating system and programs. If you have access to the internet, download the latest application and hardware driver updates for the operating system you plan to install. Copy these to a removable medium.
Upgrading The Computer 4. 5. 6. Push the parallel hard disk assembly in the direction of the arrow 5 (serial HDD’s push in the opposite direction - see sidebar) and lift the assembly 6 up out off the computer. Remove screws 7 - 10 in order to separate the bracket from the hard disk. Reverse the process to install a new hard disk(s). Parallel HDD 8 Hard Disk Connectors There are two hard disk connectors on this computer.
Upgrading The Computer Contact Warning 6 Be careful not to touch the metal pins on the module’s connecting edge. Even the cleanest hands have oils which can attract particles, and degrade the module’s performance. Upgrading the System Memory (RAM) The computer has two memory sockets for 200 pin Small Outline Dual In-line (SO-DIMM) DDR type memory modules (see “Memory” on page E - 2). The total memory size is automatically detected by the POST routine once you turn on your computer. 1. 2. 3.
Upgrading The Computer 4. 5. Set the keyboard aside. Remove screws 6 & 7 shielding plate 8 .
Upgrading The Computer 6. Gently pull the two release latches ( 9 & 10 ) on the sides of the memory socket in the direction indicated by the arrows. Figure 6 - 6 RAM Removal 9 10 9 10 11 11 6 7. 8. 9. 10. 11. 12. 13. The RAM module 11 will pop-up, and you can remove it. Pull the latches to release the second module if necessary. Insert a new module holding it at about a 30° angle and fit the connectors firmly into the memory slot. The module’s pin alignment will allow it to only fit one way.
Upgrading The Computer Changing the Secondary Bay Device 1. 2. 3. 4. Turn off the computer, and turn it over and remove the battery. Move and hold the secondary bay release latch 1 (on the left side of the computer) in the direction of the arrow. Pull the device 2 out of the bay while gripping it at point 3 . When inserting a new device make sure it is pushed fully into the slot until the release latch 1 clicks down to lock the device in position.
Upgrading The Computer Warranty The CPU is not a user serviceable part. Opening this compartment, or accessing the CPU in any way, may violate your warranty. 6 Upgrading the Processor If you want to upgrade your computer by replacing the existing processor with a faster/new one you will need to contact your customer service representative. We recommend that you do not do this yourself, since if it is done incorrectly you may damage the processor or mainboard.
Modules Chapter 7: Modules Overview This chapter contains the information on the various modules (some of which are optional) which may come with your computer, depending on the configuration purchased. If you are unsure please contact your service representative.
Modules The Mini-PCI WLAN Module Options If your purchase option includes the any of the Wireless LAN module options, follow the information on the following pages for instructions on installing the driver. Pay careful attention to the warnings concerning the use of wireless modules aboard aircraft, and the instructions on enabling/disabling power to the modules. Before installing the Wireless LAN driver, make sure that the optional WLAN module is on (the LED will be green).
Modules MSI 6855A (802.11b/g) Wireless LAN Driver Installation 1. Insert the WLAN CD-ROM into the CD/DVD drive. 2. The program will run automatically. 3. Click Install Software and click Next. 4. Click the button to accept the license agreement, then click Next. 5. Click Install. 6. Click Finish and exit the install screen. 7. Access any available wireless networks from Network Connections control panel in Windows (see sidebar).
Modules Network Connection 7 Use the Windows Network Connections control panel to access available wireless networks (Start > Settings > Network Connections or Start > Connect To > Show all Connections). ZCOM (802.11a/b/g) WLAN Module Driver Installation 1. Insert the WLAN CD-ROM into the CD/DVD drive. 2. Click Start (menu) > Run... and navigate (Browse..) to D:\Utility\ SETUP.exe and click OK. 3. Click Next > Next > Finish to complete the installation. 4.
Modules The Bluetooth Module Before installing the Bluetooth driver, make sure that the optional Bluetooth module is on. Use the Bluetooth AP-key button to toggle power to the Bluetooth module. Make sure you install the drivers in the order indicated in Table 4 - 1, on page 4 - 6. Bluetooth Module Driver Installation 1. Insert the Bluetooth CD-ROM into the CD/DVD drive. 2. The program will run automatically. 3. Click Install (button). 4. Click the button to accept the license agreement, then click OK. 5.
Modules Figure 7 - 3 Bluetooth Control Panels/ Help (Windows XP) 7 7 - 6 The Bluetooth Module
Modules The 7-in-1 Card Reader Module This optional card reader allows you to use some of the latest digital storage cards. Push the card into the slot and it will appear as a removable device. The following formats can be read by the card reader: • • • • • • • MMC (MultiMedia Card) SD (Secure Digital) MS (Memory Stick) MS (Memory Stick Pro) SM (SmartMedia Card) CF (Compact Flash Types I & II) MD (IBM Microdrive) Card Reader Cover Make sure you keep the cover in the card reader when not is use.
Modules TV Tuner Remote The remote control unit provided with the optional TV Tuner will only function when the computer is powered from the AC adapter, and not while the computer is powered by the internal battery. 7 The TV Tuner Module The optional TV Tuner allows you to watch TV, play music CDs, video conference and capture still images and video on your PC. The TV Tuner comes with a remote control unit, cable and a CD containing the utility software.
Modules Installing the AverTV Utility Software 1. Insert the AverTV Utility CD-ROM into the CD/DVD drive. 2. Click TV Utility Software. 3. Click Yes > Next > Next (click Cancel if asked a Found New Hardware Wizard appears). 4. Click Finish. 5. Run the program from the Start > Programs/All Programs > AVer TV menu, and select the Aver TV program, or double-click the icon on the desktop. Insert the AverTV Utility CD-ROM and click Acrobat Reader 5.
Modules PC Camera & TV Tuner 7 If you have the optional TV Tuner included in your purchase, make sure you install the TV Tuner driver and application first. After installing the PC Camera driver you will need to select which device to use with the BisonCap program. Go to the Devices menu in the BisonCap program and select the BisonCam, USB2.0 device.
Modules Kenmec PC Camera Driver Installation (WinXP) 1. Insert the PC Camera CD-ROM into the CD/DVD drive. 2. Click Start (menu) > Run... and navigate (Browse..) to D:\Setup.exe and click OK. 3. Choose the language you prefer and click OK > Next. 4. Click Finish to complete the installation. 5. Run the BisonCap application software from the Bs350u2 shortcut on the desktop, or from the Bs350u2 item in the Start > Programs/ All Programs menu (give the computer time to find the hardware).
Modules PC Camera Audio Setup Taking Still Pictures You may take still pictures in the Windows XP operating system only. 7 Double-click the My Computer icon on the desktop, or go the Start menu and point to My Computer, then click it. Double-click BisonCam, icon. If you wish to capture video & audio with your camera, it is necessary to setup the audio recording options in Windows. 1. 2. 3. 4. 5. 6. 7.
Modules Figure 7 - 6 Audio Setup (Windows XP) 7 The PC Camera Module Options 7 - 13
Modules Pre-Allocating File Space BisonCap BisonCap is a video viewer useful for general purpose video viewing and testing, and can capture video files to .avi format. 1. You may pre-allocate the file size for the capture file in the BisonCap program. You can choose to ignore this by clicking Cancel.
Modules Eliminating Screen Flicker If you find that the video screen in the BisonCap program is flickering, you can try to adjust the setting in the Video Capture Filter options. 1. 2. 3. Run the BisonCap program. Go to Options and scroll down to select “Video Capture Filter...”. Click either 50Hz or 60Hz under Frequency in Property Page (tab).
Modules 7 7 - 16
Troubleshooting Chapter 8: Troubleshooting Overview Should you have any problems with your computer, before consulting your service representative, you may want to try to solve the problem yourself. This chapter lists some common problems and their possible solutions. This can’t anticipate every problem, but you should check here before you panic. If you don’t find the answer in these pages, make sure you have followed the instructions carefully and observed the safety precautions in the preface.
Troubleshooting Basic Hints and Tips Many of the following may seem obvious but they are often the solution to a problem when your computer appears not to be working. • Power - Is the computer actually plugged into a working electrical outlet? If plugged into a power strip, make sure it is actually working. Check the LED Power Indicators (see “LED Indicators” on page 1 - 8) to see the computer’s power status. • Connections - Check all the cables to make sure that there are no loose connections anywhere.
Troubleshooting Backup and General Maintenance • Always backup your important data, and keep copies of your OS and programs safe, but close to hand. Don’t forget to note the serial numbers if you are storing them out of their original cases, e.g. in a CD wallet. • Run maintenance programs on your hard disk and OS as often as you can. You may schedule these programs to run at times when you are not using your computer.
Troubleshooting Viruses • Install an Anti-Virus program and keep the definitions file (the file which tells your program which viruses to look for) up to date. New computer viruses are discovered daily, and some of them may seriously harm your computer and cause you to lose data. Anti-Virus programs are commercially available and the definitions file updates are usually downloadable directly from the internet. • Be careful when opening e-mail from sources you don’t know.
Troubleshooting Upgrading and Adding New Hardware/Software • Do not be tempted to make changes to your Windows Registry unless you are very sure of what you are doing, otherwise you will risk severely damaging your system. • Don’t open your computer or undertake any repair or upgrade work if you are not comfortable with what you are doing. • Read the documentation.
Troubleshooting • Thoroughly check any recent changes you made to your system as these changes may affect one or more system components, or software programs. If possible, go back and undo the change you just made and see if the problem still occurs. • Don’t over complicate things.
Troubleshooting Power Problem Possible Cause - Solution You turned on the power but it doesn’t work. Battery missing / incorrectly installed. Check the battery bay, make sure the battery is present and seated properly (the design of the battery only allows it to go in one way). Make sure there’s nothing interfering with the battery contacts. The Battery LED power indicator , is blinking orange. Low Battery. Plug in the AC power source.
Troubleshooting Problem Possible Cause - Solution The computer feels too hot. Make sure the computer is properly ventilated and the vents/fan intakes are not blocked. If this doesn’t cool it down, put the system into Hibernate mode or turn it off for an hour. Make sure the computer isn’t sitting on a thermal surface (see “Overheating” on page 1 11). Make sure you’re using the correct adapter.
Troubleshooting Display Problem Nothing screen. appears Possible Cause - Solution on The system is in a power saving mode. Toggle the sleep/resume key combination, Fn + F4 (see “Sleep Button” on page 3 - 8). \ The screen controls need to be adjusted. Toggle the screen control key combinations Fn + F8/F9). If you’re connected to an external monitor, make sure it’s plugged in and turned on. You should also check the monitor’s own brightness and contrast controls.
Troubleshooting Boot Password Problem You forget password. the Possible Cause - Solution boot If you forget the password, you may have to discharge the battery of the CMOS. Contact your service representative for help. Password Warning 8 If you choose to set a boot password, NEVER forget your password. The consequences of this could be serious. If you cannot remember your boot password you must contact your vendor and you may lose all of the information on your hard disk.
Troubleshooting Audio & CD Device Problem Possible Cause - Solution The sound cannot be heard or the volume is very low. The volume might be set too low. Check the volume control in the Volume Control Panel in the Windows taskbar, or use the key combination Fn + F5 and F6 (see “Audio Features” on page 2 - 12) to adjust. The compact disc cannot be read. The compact disc is dirty. Clean it with a CD-ROM cleaner kit. The compact disc tray will not open when there is a disc in the tray.
Troubleshooting Keyboard Problem Unwelcome numbers appear when typing. Possible Cause - Solution If the LED is lit, then Num Lock is turned ON (see “LED Indicators” on page 1 - 8). Other Keyboards 8 If your keyboard is damaged or you just want to make a change, you can use any standard USB keyboard. The system will detect and enable it automatically. However special functions/hot keys unique to the system’s regular keyboard may not work.
Troubleshooting Operation Problem Possible Cause - Solution The system freezes or the screen goes dark. The system’s power saving features have timed-out. Use the AC adapter, press a key on the keyboard, or press the sleep (Fn + F4) key combination, or press the power button if no LEDs are lit. The system never goes into a power saving mode. Power Options features are not enabled. Go to the Windows Power Options menu and enable the features you prefer (see “System Power Options” on page 3 - 6).
Troubleshooting Modules 8 Problem Possible Cause - Solution The Wireless LAN/ Bluetooth/PC Camera modules cannot be detected. The modules are off. Check the LED indicator to see if the wireless modules are on or off (see “LED Indicators” on page 1 - 8). If the LED indicator is off, then press the appropriate AP-key button in order to enable the modules (see Table 1 - 3 “- AP-key Buttons” on page 1 - 9 The Wireless LAN/ Bluetooth/ modules cannot be configured.
Interface (Ports & Jacks) Appendix A: Interface (Ports & Jacks) Overview The following chapter will give a quick description of the interface (ports & jacks) which allow your computer to communicate with external devices, connect to the internet etc.
Interface (Ports & Jacks) Ports and Jacks Item Built-In Microphone CATV-In Jack DC-In Jack Description The built-in microphone allows you to record on your computer Use this jack to connect a CATV cable if you have included the optional Mini-PCI TV Tuner in your purchase. Plug the supplied AC adapter into this jack to power your computer.
Interface (Ports & Jacks) Item Microphone-In Jack Mini-IEEE 1394a Port Description Plug an external microphone in to this jack to record on your computer. This allows high-speed connection to various peripheral devices, e.g. external disk drives and digital cameras (see note below). IEEE 1394 The Mini-IEEE 1394a ports only support SELF POWERED IEEE 1394 devices. Parallel Port Connect a parallel type printer to this port.
Interface (Ports & Jacks) Item Description RJ-45 LAN Jack This port supports LAN (Network) functions. Note: Broadband (e.g. ADSL) modems usually connect to the LAN port. S/PDIF-Out Jack This S/PDIF (Sony/Philips Digital Interface Format) Out Port allows you to connect your DVD-capable PC to a Dolby AC-3 compatible receiver for “5.1” or ‘dts’ surround sound. Security Lock Slot To prevent possible theft, a Kensington-type lock can be attached to this slot. Locks can be purchased at any computer store.
Appendix B: NVIDIA Video Driver Controls The basic settings for configuring the LCD are outlined in “Video Features” on page 1 - 16. Video Card Options NVIDIA Video Driver Installation Make sure you install the drivers in the order indicated in Table 4 - 1, on page 4 - 6. 1. Run the Notebook Driver Installation application and double-click VIDEO. OR Click Start (menu) > Run... and navigate (Browse..) to D:\Drivers\05NVIDIA\setup.exe and click OK. 2.
NVIDIA Taskbar Icon Click the NVIDIA icon in the taskbar to bring up the troubleshooting menu, and go to the GeForce Go 6800 Properties from the menu (click NVIDIA Display > Laptop Display). B If you cannot see the tray icon , go to the GeForce Go 6800 Properties control panel tab and select the Troubleshooting item from the Additional Properties menu. Click the tickbox “Display the NVIDIA Settings icon in the taskbar”.
Additional Properties The items listed in the Additional Properties window allow you to configure your display(s). If the items do not display you can either click the Additional Properties button, or click the icon . Figure B - 1 Additional Properties Click pin icon to push pin in to keep the menu open. B Some screen examples are shown on the following page.
You may make changes to the Display Settings, Color Correction, Video Overlay, Resolutions, Refresh Rates and Screen Rotation by clicking the appropriate tab and adjusting the setting. Figure B - 2 Screen Examples Help Menus B Right-click on many of the items in the tabs to bring up the “What’s This?” button. Click the “What’s This?” button to bring up the help menu. B - 4 NVIDIA Display Properties Right-click on a control panel item to bring up a Help menu (see sidebar).
NVIDIA nView Desktop Manager The nView Desktop Manager allows quick access to control panels for features such as Desktop Management, Profiles, Hot Keys etc. The Control panel may be accessed as follows. 1. 2. Click Start, point to Settings and click Control Panel (or just click Control Panel). Double-click NVIDIA nView Desktop Manager (icon) - Click "Switch to Classic View" from the left of the menu if you are in Category View. Right-click the Enable button to display the Desktop Management options menu.
Display Wizard Use the Display Wizard in the Desktop Management window to quickly setup and configure any attached displays (see Figure B - B - 3 on page B - 5). Display Devices Besides the built-in LCD, you can also use an external monitor/flat panel display or TV/HDTV as your display device. The following are the display options: 1. 2. 3. 4. The built-in LCD. An external monitor connected to the DVI-Out Port (may require DVI to VGA converter).
Attaching Other Displays If you prefer to use a monitor or flat panel display, connect it to the DVI-Out Port at the rear of the computer. 1. 2. 3. 4. 5. 6. Attach your external monitor to the DVI-Out Port (or TV/HDTV to the SVideo-Out Port), and turn it on. Go to Additional Properties in the GeForce Go 6800 Properties control panel tab (“NVIDIA Display Properties” on page B - 2). Select nView Display Settings (available if external display is attached).
7. Select the display option from the Primary Display/ Secondary Display dropbox. If you have a TV and external monitor/flat panel display attached you will have a number of available options (see sidebar). Select and Apply the appropriate option. 8. Click the monitor icon to select it, then click the Device Settings button to make any adjustments for the selected display (including Screen Resolutions & Refresh Rates). Click Apply to confirm any setting changes.
Display Modes Single Display Mode Only one of your displays is used. Clone Mode Clone Mode simply shows an exact copy of the Primary display desktop on the other display(s). This mode will drive multiple displays with the same content and each display device can be configured independently. Dualview Mode Dualview Mode treats both connected displays as separate devices, and they act as a virtual desktop resulting in a large workspace.
Enabling TV Display To display desktop images on a TV, connect the TV to your computer by using an S-Video cable from the TV to the S-Video-Out Port at the rear of the computer (see “System Map: Front & Rear Views” on page 1 - 11). You will need to enable the TV display from the nView Display Settings tab (see “Attaching Other Displays” on page B - 7). The TV will appear as a display option (select the display option from the Primary Display/ Secondary Display dropbox) when attached to the S-Video-Out Port.
Set the TV format from the Select TV Format menu. The Advanced option (in Dualview mode) at the bottom of the Select TV Format menu allows you to select TV format by country if you are unsure of your TV format. Figure B - 7 TV Settings and Adjustments B Device Adjustments (Device Settings menu) allows you to make changes to the TV output.
B B - 12
ATI Video Driver Controls Appendix:C: ATI Video Driver Controls The basic settings for configuring the LCD are outlined in “Video Features” on page 1 - 16. Video Card Options ATI Video Driver Installation Make sure you install the drivers in the order indicated in Table 4 - 1, on page 4 - 6. 1. Run the Notebook Driver Installation application and double-click VIDEO. OR Click Start (menu) > Run... and navigate (Browse..) to D:\Drivers\05ATI\Setup.exe and click OK. 2.
ATI Video Driver Controls ATI Taskbar Icon You can also access ATI Mobility Radeon X800 Properties by right-clicking the ATI icon in the taskbar. Point to Settings and click ATI Display Settings, then click the Settings (tab). ATI Mobility Radeon X800 Properties More advanced video configuration options are provided in the ATI Mobility Radeon X800 control panel tab: 1. 2. 3. 4. Open the Display Properties (see “Video Features” on page 1 - 16) control panel. Click Advanced (button).
ATI Video Driver Controls Figure C - 2 ATI Mobility Radeon X800 Properties Tabs Help Menus Right-click on almost any item in the tabs to bring up the “What’s This?” button. Help Menu Click to Configure Theater Mode (Not Supported with TV Tuner) Click the “What’s This?” button to bring up the help menu. Theater Mode Theater Mode is not supported with the TV Tuner module installed (see page C - 4).
ATI Video Driver Controls Theater Mode Theater Mode can be enabled by clicking Clone Mode Options (button) in the Overlay tab from the ATI Mobility Radeon X800 Properties. (see page C 3). Theater Mode enables you to display video playback in full screen on a secondary monitor. Theater Mode is not supported if you have the TV Tuner module installed.
ATI Video Driver Controls Attaching Other Displays If you prefer to use a monitor or flat panel display, connect it to the DVI-Out Port at the rear of the computer. 1. 2. 3. 4. 5. Attach your external monitor to the DVI-Out Port (or TV/HDTV to the SVideo Out Port), and turn it on. Select the Displays tab in the ATI Mobility Radeon X800 properties. Click the enable/disable button / for the display device you wish to use. Click Apply. Click Yes to accept the settings and OK to save the changes.
ATI Video Driver Controls Primary & Clone Displays Display Modes Single Only one of your displays is used. The Primary display in an Extended Desktop environment will be associated with display Icon 1 in the settings tab. Multiple - Clone Mode Clone Mode simply shows an exact copy of the Primary display desktop on the other display(s). This mode will drive multiple displays with the same content and each display device can be configured independently.
ATI Video Driver Controls Clone Mode Clone Mode simply shows an exact copy of the Primary display desktop on the other display(s). This mode will drive multiple displays with the same content. Use this feature to display the screen through a projector for a presentation. Each display device can be configured independently as this allows you to set the options for overhead projectors etc., which require specific resolutions and refresh rates.
ATI Video Driver Controls Extended Desktop Mode The system supports Extended Desktop in multiple display environments in WindowsXP. An Extended Desktop creates a desktop spanning multiple displays and acts as a large workspace. To get this effect: 1. 2. 3. 4. 5. 6. 7. 8. 9. C C - 8 Display Modes Attach your external monitor to the DVI-Out port (or TV/HDTV to the SVideo Out Port), and turn it on. Select the Displays tab in the ATI Mobility Radeon X800 properties.
ATI Video Driver Controls 10. In the example shown in Figure C - 5 the primary monitor 1 is on the left, the other display is on the right. Help Click either the Display popup menu, or click the icon for the appropriate display. Then click the tick box to extend the primary display’s desktop to it. Further help is available through the menus accessed from the taskbar (see Figure C - 1 on page C2). Figure C - 5 Extended Desktop Monitor Arrangement 11.
ATI Video Driver Controls 12. One display will be set to 1 (Primary). The displays may be switched as long as one as set to Primary. Figure C - 6 Displays Tab (Extended Desktop Mode) In this picture the notebook LCD panel is the primary display, and the desktop may be extended to any attached displays. The primary display is indicated with a button depressed. Click the buttons to switch the primary display. 13.
ATI Video Driver Controls Enabling TV Display To display desktop images on a TV, connect the TV to your computer by using an S-Video cable from the TV to the S-Video-Out Port at the rear of the computer (see “System Map: Front & Rear Views” on page 1 - 11). Further help is available to help you troubleshoot your TV connection through the menus accessed from the taskbar (see page Figure C - 1 on page C-2).
ATI Video Driver Controls C C - 12
1.8" Top Case LCD Appendix D: 1.8" Top Case LCD The 1.8" TFT Top Case LCD can be used to display company logos, personal photos, animated files etc. The following file formats are supported: • 24 bit depth Bitmap (.bmp) files which are 128 pixel wide * 160 pixel high • 32 bit depth GIF or animated .GIF files which are 128 pixel wide * 160 pixel high Press to Toggle Power On/Off Flash1.8" LCD Top Case & Battery Power The 1.
1.8" Top Case LCD Flash Top Case Logo This BIOS item allows you to enable the serial port for application programming of the top case logo. After programming the logo make sure you reset the option to “Disabled” (default) otherwise the serial port will not work. BIOS Setting Before using the application (LCDAP.EXE) provided on the Device Drivers and Utilities CD-ROM to program the files displayed on the 1.8" LCD, you must enable the setting in the BIOS: 1. 2. 3. 4.
1.8" Top Case LCD Using the LCDAP Program Your computer may already come with LCDAP.EXE pre-installed on the hard disk (e.g. on the C: drive). Where this is not the case, or where you are re-configuring your computer the LCDAP.EXE is provided on the Device Drivers and Utilities CD-ROM: 1. Run the Notebook Driver Installation application and double-click LCDAP. OR Click Start (menu) > Run... and navigate (Browse..) to D:\Drivers\ 10LCDAP\LCDAP.exe and click OK. 2.
1.8" Top Case LCD Browse to the LCDAP folder on the computer’s hard disk and double-click LCDAP (.EXE) to run the program.
1.8" Top Case LCD LCDAP Files There are 12 slots available for user files in the LCADAP program, and one fixed slot display the manufacturer’s logo. Adding Files 1. To add a file click on any of the 12 slots to select it, and click Open File (button), or double-click on any empty slot, or right-click a slot or file. 2. Select a file and click Open to add the file to the slot (files may be replaced but not deleted). Transition Type The Type box lists four types of transiting for selected slides.
1.8" Top Case LCD Update Program Warning Avoid using the Update Program button as this information is not modifiable in user mode.. Selecting & Configuring Files to Display 1. To select files to display double-click the file to highlight it (it will be outlined in blue). 2. You can select up to 12 files to display, however this is dependent upon the file size (a maximum of 512 Kbytes of files may be selected). 3.
Specifications Appendix E: Specifications Latest Specification Information The specifications listed in this Appendix are correct at the time of going to press. Certain items (particularly processor types/speeds and CD/DVD device types) may be changed or updated due to the manufacturer's release schedule. Check with your service center for details.
Specifications Feature Specification Processor Types Intel® Pentium® 4 520/ 530/ 540/ 550/ 560/ 570 Processor with HT Technology LGA775 Package (775-pin) (90nm) 90 Nanometer Process Technology, 1024KB On-Die L2 Cache & 800MHz Front Side Bus - 2.8/ 3.0/ 3.2/ 3.4/ 3.6/ 3.
Specifications Feature Specification Video Card Options Option One: Option Two: ATI M28 (X800) High Performance Chip 256MB DDR-III (DDR3) Video RAM On Board 128-bit Graphics Engine PCI Express * 16 Full DirectX® 9 Support Dual-View Display Monitor HDTV Output Support NVIDIA GeForce 6800 High Performance Chip 256MB DDR-III (DDR3) Video RAM On Board 128-bit Graphics Engine PCI Express * 16 Full DirectX® 9 Support Dual-View Display Monitor HDTV Output Support Storage Options One Changeable Primary Seri
Specifications Feature Specification Audio SRS WOW Surround Sound Technology inside Intel Azalia High Definition Audio Interface 3D Stereo Enhanced Sound System Virtual 7.1 - Channel Sound System Compatible with Sound-Blaster PRO™ S/PDIF Digital Output (7.
Specifications Feature Communication Specification Infrared Transceiver Infrared Transfer 1cm ~ 1M Operating Distance 115.2K bps SIR 4M bps FIR IrDA 1.1 Compliant 802.11b/g OR 802.11a/b/g Mini-PCI Wireless LAN Module (Optional) PCI-Express 10/100/1000 BASE-T Fast Ethernet LAN on board 300K Pixel Video Camera Module (Optional) Integrated V.90/56K Azalia Modem (V.92 Compliant) Bluetooth™ 1.
Specifications Feature Specification Physical Dimensions & Weight 360mm (w) * 292mm (d) * 37-52mm (h) 4.5 kg with Battery Optional 2nd Parallel (PATA) Hard Disk Drive 802.11b/g OR 802.11a/b/g Mini-PCI Wireless LAN Module DVD/CD-RW Combo Drive Module DVD-Dual Drive Module Bluetooth™ 1.
