Preface Notice The company reserves the right to revise this publication or to change its contents without notice. Information contained herein is for reference only and does not constitute a commitment on the part of the manufacturer or any subsequent vendor. They assume no responsibility or liability for any errors or inaccuracies that may appear in this publication nor are they in anyway responsible for any loss or damage resulting from the use (or misuse) of this publication.
Preface FCC Statement (Federal Communications Commission) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Preface IMPORTANT SAFETY INSTRUCTIONS Follow basic safety precautions, including those listed below, to reduce the risk of fire, electric shock, and injury to persons when using any electrical equipment: 1. 2. 3. 4. 5. Do not use this product near water, for example near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool. Avoid using this equipment with a telephone line (other than a cordless type) during an electrical storm.
Preface Instructions for Care and Operation The notebook computer is quite rugged, but it can be damaged. To prevent this, follow these suggestions: 1. Don’t drop it, or expose it to shock. If the computer falls, the case and the components could be damaged. Do not expose the computer to any shock or vibration. 2. Do not place anything heavy on the computer. Keep it dry, and don’t overheat it. Keep the computer and power supply away from any kind of heating element. This is an electrical appliance.
Preface 3. Avoid interference. Keep the computer away from high capacity transformers, electric motors, and other strong magnetic fields. These can hinder proper performance and damage your data. 4. Follow the proper working procedures for the computer. Shut the computer down properly and don’t forget to save your work. Remember to periodically save your data as data may be lost if the battery is depleted. Do not turn off the power until you properly shut down all programs. 5.
Preface Power Safety The computer has specific power requirements: Power Safety Warning Before you undertake any upgrade procedures, make sure that you have turned off the power, and disconnected all peripherals and cables (including telephone lines). It is advisable to also remove your battery in order to prevent accidentally turning the machine on. VI • Only use a power adapter approved for use with this computer.
Preface Battery Precautions • Only use batteries designed for this computer. The wrong battery type may explode, leak or damage the computer. • Do not remove any batteries from the computer while it is powered on. • Do not continue to use a battery that has been dropped, or that appears damaged (e.g. bent or twisted) in any way. Even if the computer continues to work with a damaged battery in place, it may cause circuit damage, which may possibly result in fire.
Preface Cleaning Do not apply cleaner directly to the computer; use a soft clean cloth. Do not use volatile (petroleum distillates) or abrasive cleaners on any part of the computer. Servicing Do not attempt to service the computer yourself. Doing so may violate your warranty and expose you and the computer to electric shock. Refer all servicing to authorized service personnel. Unplug the computer from the power supply.
Preface Travel Considerations Packing As you get ready for your trip, run through this list to make sure the system is ready to go: 1. 2. 3. 4. 5. 6. 7. 8. Check that the battery pack and any spares are fully charged. Power off the computer and peripherals. Close the display panel and make sure it’s latched. Disconnect the AC/DC adapter and cables. Stow them in the carrying bag. The AC/DC adapter uses voltages from 100 to 240 volts so you won’t need a second voltage adapter.
Preface On the Road In addition to the general safety and maintenance suggestions in this preface, and Chapter 8: Troubleshooting, keep these points in mind: Hand-carry the notebook - For security, don’t let it out of your sight. In some areas, computer theft is very common. Don’t check it with “normal” luggage. Baggage handlers may not be sufficiently careful. Avoid knocking the computer against hard objects.
Preface Developing Good Work Habits Developing good work habits is important if you need to work in front of the computer for long periods of time. Improper work habits can result in discomfort or serious injury from repetitive strain to your hands, wrists or other joints. The following are some tips to reduce the strain: • Adjust the height of the chair and/or desk so that the keyboard is at or slightly below the level of your elbow. Keep your forearms, wrists, and hands in a relaxed position.
Preface Lighting Proper lighting and a comfortable viewing angle can reduce eye strain and shoulder and neck muscle fatigue. • • • • Position the display to avoid glare or reflections from overhead lighting or outside sources of light. Keep the display screen clean and set the brightness and contrast to levels that allow you to see the screen clearly. Position the display directly in front of you at a comfortable viewing distance. Adjust the display-viewing angle to find the best position.
Preface Contents Notice .................................................................................I FCC Statement .............................................................II Instructions for Care and Operation .......................... IV Power Safety .............................................................. VI Battery Precautions ...................................................VII Cleaning .................................................................. VIII Servicing ...............
Preface Parallel Printer ...........................................................2-12 Power Management Overview ........................................................................3-1 The Power Sources ........................................................3-2 AC/DC Adapter ...........................................................3-2 Battery .........................................................................3-2 Turning on the Computer ...............................................
Preface BIOS Utilities Upgrading The Computer Overview ........................................................................5-1 The Power-On Self Test (POST) ...................................5-2 Failing the POST .........................................................5-3 Fatal Errors .................................................................5-3 Non-Fatal Errors .........................................................5-3 The Setup Program .....................................................
Preface PC Camera Audio Setup ...........................................7-18 BisonCap (for 1.3M pixel camera module) ...............7-20 Eliminating Screen Flicker (BisonCap) ....................7-21 Video View (for 2.0M pixel camera module) ...........7-22 Mini-PCI TV Tuner Module ........................................7-25 MPC788/MPC718 Driver & Software .....................7-26 Digital TV Broadcast Signal ....................................7-28 TV Recording and Power Plans ...........................
Preface Specifications Processor Types ............................................................ C-2 Core Logic .................................................................... C-2 LCD .............................................................................. C-3 Security ......................................................................... C-3 Memory ......................................................................... C-3 BIOS ...........................................................
Preface Chipset ........................................................................D-28 Video ...........................................................................D-28 Audio ..........................................................................D-28 Modem ........................................................................D-28 LAN ............................................................................D-28 TouchPad ....................................................................
Quick Start Guide Chapter 1: Quick Start Guide Overview This Quick Start Guide is a brief introduction to the basic features of your computer, to navigating around the computer and to getting your system started. The remainder of the manual covers the following: • Chapter 2 • Chapter 3 • Chapter 4 • Chapter 5 • Chapter 6 • Chapter 7 • Chapter 8 • Appendix A • Appendix B • Appendix C • Appendix D A guide to using some of the main features of the computer e.g.
1 Quick Start Guide Advanced Users If you are an advanced user you may skip over most of this Quick Start Guide. However you may find it useful to refer to “Drivers & Utilities” on page 4 - 1, “BIOS Utilities” on page 5 - 1 and “Upgrading The Computer” on page 6 - 1 in the remainder of the User’s Manual. You may also find the notes marked with a of interest to you. Notes Check the light colored boxes with the mark above to find detailed information about the computer’s features.
Quick Start Guide Not Included Operating Systems (e.g. Windows Vista/ Windows XP etc.) and applications (e.g. word processing, spreadsheet and database programs) have their own manuals, so please consult the appropriate manuals. Drivers If you are installing new system software, or are re-configuring your computer for a different system, you will need to install the appropriate drivers. Drivers are programs which act as an interface between the computer and a hardware component e.g.
1 Quick Start Guide TV Tuner Module Support Note that the TV Tuner module (factory) options in Windows Vista are supported by the Windows Media Center software which comes built-in to the Windows Vista Home Premium and Ultimate Editions only. If your purchase includes a TV Tuner option, and you are reconfiguring your system for a different system, you should install either Windows Home Premium or Ultimate Editions only.
Quick Start Guide System Startup 1. 2. 3. 4. 5. 6. 7. 8. Remove all packing materials. Place the computer on a stable surface. Securely attach any peripherals you want to use with the notebook (e.g. keyboard and mouse) to their ports. Attach the AC/DC adapter to the DC-In jack at the rear of the computer, then plug the AC power cord into an outlet, and connect the AC power cord to the AC/DC adapter.
1 Quick Start Guide 1. Optional Built-In PC Camera 2. LCD 3. LED Power & Communication Indicators 4. Built-In Microphone 5. LED Status Indicators 6. Hot Key Buttons 7. Power Button 8. Keyboard 9. Speakers 10. Game Hot Keys 11. Touchpad & Buttons System Map: LCD Panel Open 1 Wireless Device Operation Aboard Aircraft 2 The use of any portable electronic transmission devices (e.g. WLAN or Bluetooth) aboard aircraft is usually prohibited.
Quick Start Guide LED Indicators The two sets of LED indicators (LED Status Indicators and LED Power & Communication Indicators) on the computer display helpful information about the current status of the computer.
1 Quick Start Guide Hot Key Buttons & Keyboard These buttons give instant access to the default Internet browser and e-mail program, and to a user-defined application, with one quick button press. To use the “user-defined application Hot Key Button”, you must install the driver. See “Application Hot Key” on page 2 - 8 for configuration instructions.
Quick Start Guide Keys Description Keys Description Fn + ~ Play/Pause (in Audio/Video Programs) Fn + F7 Display Toggle Fn + F1 TouchPad Toggle Fn + F8 Decrease LCD Brightness Fn + 1 Fan Automatic Control / Full Power Fn + F9 Increase LCD Brightness Fn + F3 Mute Toggle Fn + F10 PC Camera Toggle Fn + F4 Sleep Toggle Fn + F11 WLAN Module Toggle Fn + F5 Decrease Audio Volume Fn + F12 Bluetooth Module Toggle Fn + F6 Increase Audio Volume Fn + Scr Lk Scroll Lock Toggle Table 1 - 5
1 Quick Start Guide 1. 2. 3. 4. LCD Latches Line-In Jack S/PDIF-Out Jack Microphone-In Jack 5. Headphone-Out Jack 6. Speakers 7. Vent/Fan Intake 8. DC-In Jack 9. DVI-Out Port 10. S-Video-In Jack* System Map: Front & Rear Views 1 1 6 7 6 2 3 4 5 8 *Enabled with Optional Mini-PCI TV Tuner Only 7 9 10 Overheating To prevent your computer from overheating make sure nothing blocks the vent(s)/fan intake(s) while the computer is in use.
Quick Start Guide System Map: Left View 1. 2. 3. 1 2 3 4 5 6 9 7 4. 8 5. 6. Mini-IEEE 1394 Port 7. The Mini-IEEE 1394 port only supports SELF POWERED IEEE 1394 devices. 8. ExpressCard Slot The ExpressCard Slot accepts either ExpressCard/34 or ExpressCard/54 formats. 7-in-1 Card Reader 9.
1 Quick Start Guide Disk Eject Warning Changing DVD Regional Codes Don’t try to eject a CD/DVD while the system is accessing it. This may cause the system to “crash”. Stop the disk first then eject it, or press the stop button twice. Go to the Control Panel and double-click Device Manager (Hardware and Sound), then click the + next to DVD/CD-ROM drives.
Quick Start Guide System Map: Right & Bottom Views 1. 2. 2 1 1 4. 5. 6 4 4 4 3. 4 6. 5 3 USB Ports Security Lock Slot Battery (Secondary HDD Bay - HDD3) Fan Outlet/Intake Primary HDD Bay (HDD1 & HDD2) Component Bay Cover Battery Information Always completely discharge, then fully charge, a new battery before using it.
1 Quick Start Guide Windows Vista Start Menu & Control Panel Most of the control panels, utilities and programs within Windows Vista (and most other Windows versions) are accessed from the Start menu. When you install programs and utilities they will be installed on your hard disk drive, and a shortcut will usually be placed in the Start menu and/or the desktop. You can customize the look of the Start menu by right-clicking the Start menu and selecting Properties from the menu.
Quick Start Guide Video Features You can configure display options, from the Display Settings control panel in Windows as long as the appropriate video driver is installed. For more detailed video information see “NVIDIA Video Driver Controls” on page B - 1. To access Display Settings in Windows: 1. 2. 3. 4. 5. 6. 7. 8. Click Start, and click Control Panel (or point to Settings and click Control Panel).
1 Quick Start Guide Display Devices & Options Besides the built-in LCD, you can also use an external VGA monitor (CRT)/external Flat Panel Display (connected to the DVI-Out port) or TV (connected to the S-Video-Out jack) as your display device. 4 1 2 3 Figure 1 - 8 - Display Settings & NVIDIA Control Panel NVIDIA Display Mode Description Single One display device is used.
Quick Start Guide Power Options The Power Options (Hardware and Sound menu) control panel icon in Windows (see page 1 - 14) allows you to configure power management features for your computer. You can conserve power by means of power plans and configure the options for the power button, sleep button, computer lid (when closed), display and sleep mode from the left menu. Note that the Power saver plan may have an affect on computer performance.
1 Quick Start Guide 1 - 18
Storage Devices, Mouse, Audio & Printer Chapter 2: Storage Devices, Mouse, Audio & Printer Overview Read this chapter to learn more about the following main features and components of the computer: • • • • • • • • • Hard Disk Drive Optical Device 7-in-1 Card Reader ExpressCard Slot Application Hot Key Game Keys TouchPad and Buttons/Mouse Audio Features Adding a Printer Overview 2 - 1 2
Storage Devices, Mouse, Audio & Printer 2 Power Safety Before attempting to access any of the internal components of your computer please ensure that the machine is not connected to the AC power, and that the machine is turned off. Also ensure that all peripheral cables, including phone lines, are disconnected from the computer. Hard Disk Drive The hard disk drive(s) is(are) used to store your data in the computer. The hard disk(s) can be taken out to accommodate other 2.
Storage Devices, Mouse, Audio & Printer Optical Device There is a bay for a 5.25" optical (CD/DVD) device (12.7mm height). The actual device will depend on the model you purchased (see “Storage Options” on page C 4). The optical device is usually labeled “Drive D:” and may be used as a boot device if properly set in the BIOS (see “Boot Menu” on page 5 - 12).
Storage Devices, Mouse, Audio & Printer 2 Handling CDs or DVDs CD Emergency Eject If you need to manually eject a CD (e.g. due to an unexpected power interruption) you may push the end of a straightened paper clip into the emergency eject hole. However please do NOT use a sharpened pencil or similar object that may break and become lodged in the hole. Disk Eject Warning Don’t try to remove a CD/DVD while the system is accessing it. This may cause the system to “crash”.
Storage Devices, Mouse, Audio & Printer DVD Regional Codes 2 To change the DVD regional codes see “Changing DVD Regional Codes” on page 1 - 12. .
Storage Devices, Mouse, Audio & Printer 2 Card Reader Cover Make sure you keep the cover in the card reader when not in use. This will help prevent foreign objects and/or dust getting in to the card reader. 7-in-1 Card Reader The card reader allows you to use some of the latest digital storage cards. Push the card into the slot and it will appear as a removable device, and can be accessed in the same way as your hard disk (s).
Storage Devices, Mouse, Audio & Printer ExpressCard Slot The computer is equipped with an ExpressCard/34/54 slot that reads Express Card/ 34 and ExpressCard/54 formats. ExpressCards are the successors to PCMCIA (PC Cards). ExpressCard/54 is used for applications which require a larger interface slot, e.g. CompactFlash card reader. The number denotes the card width; 54mm for the Express Card/54 and 34mm for the ExpressCard/34.
Storage Devices, Mouse, Audio & Printer 2 Application.exe You will need to locate the actual application executable (.exe) file, not just the shortcut. To find the application rightclick its shortcut on the desktop and click Properties. Click the shortcut (tab) and see where the executable file is located by clicking the Open File Location (button).
Storage Devices, Mouse, Audio & Printer Game Keys 2 The two game hot keys on the left of the computer allow macros to be configured for common keystrokes used in applications (the keys can assigned macros for any program, not only games). To configure the keys follow the instructions below (make sure you have installed the Ap-Key Utility driver - see “Ap-Key Utility” on page 4 - 6). 1. 2. 3. Run the Game Key Configuration program from the desktop icon (or from C:\Windows\CleGameKey\GmKeyCfgUtl.exe).
Storage Devices, Mouse, Audio & Printer 2 Mouse Driver If you are using an external mouse your operating system may be able to auto-configure your mouse during its installation or only enable its basic functions. Be sure to check the device’s user documentation for details. TouchPad and Buttons/Mouse The TouchPad is an alternative to the mouse; however, you can also add a mouse to your computer through one of the USB ports. The TouchPad buttons function in much the same way as a two-button mouse.
Storage Devices, Mouse, Audio & Printer Audio Features You can configure the audio options on your computer from the Sound control panel in Windows, or from the Realtek HD Audio Manager icon in the taskbar/ control panel (right-click the taskbar icon to bring up an audio menu). The volume may also be adjusted by means of the Fn + F5/F6 key combination. Sound Volume Adjustment The sound volume level is set using the volume control within Windows (and the volume function keys on the computer).
Storage Devices, Mouse, Audio & Printer 2 Parallel Printer After setting up the printer attach the parallel cable to the printer. Connect the printer’s parallel cable to the Parallel to USB converter, and then plug the converter into the USB port. Turn ON the printer, then turn ON the computer. Windows will identify the printer and either load one of its own drivers or ask you to supply one. Follow the on-screen instructions. Adding a Printer The most commonly used peripheral is a printer.
Power Management Chapter 3: Power Management Overview To conserve power, especially when using the battery, your computer power management conserves power by controlling individual components of the computer (the monitor and hard disk drive) or the whole system.
Power Management The Power Sources The computer can be powered by either an AC/DC adapter or a battery pack. 3 AC/DC Adapter Use only the AC/DC adapter that comes with your computer. The wrong type of AC/ DC adapter will damage the computer and its components (see page C - 6). 1. 2. 3. 4. Attach the AC/DC adapter to the DC-In jack at the rear of the computer. Plug the AC power cord into an outlet, and then connect the AC power cord to the AC/DC adapter. Raise the lid/LCD to a comfortable viewing angle.
Power Management Turning on the Computer Now you are ready to begin using your computer. To turn it on simply press the power button on the front panel. When the computer is on, you can use the power button as a Sleep/Hibernate/Shut Down hot key button when it is pressed for less than 4 seconds (pressing and holding the power button for longer than this will force the computer to shut down).
Power Management 3 Resuming Operation See Table 3 - 1, on page 3 - 9 for information on how to resume from a power-saving state. Password It is recommended that you enable a password on system resume in order to protect your data. Figure 3 - 1 Power Plan Advanced Settings 3 - 4 Power Plans Power Plans The computer can be configured to conserve power by means of power plans. You can use (or modify) an existing power plan, or create a new one.
Power Management Each Windows Power Plan will also adjust the processor performance of your machine in order to save power. This is worth bearing in mind if you are experiencing any reduced performance (especially under DC/battery power). 3 Choose High performance for maximum performance when the computer is powered from an AC power source.
Power Management 3 Power Button The Power Button in the Start Menu (in Classic View use the Shut Down button ) can be used to send the computer into a powersaving state. Sleep Mode & Mobile PC Battery A mobile PC in Sleep uses very little battery power. After an extended period of time the computer will save any open documents and applications to hard disk. Power-Saving States You can use power-saving states to stop the computer’s operation and restart where you left off.
Power Management Hibernate Hibernate uses the least amount of power of all the power-saving states and saves all of your information on a part of the hard disk before it turns the system off. If a power failure occurs the system can restore your work from the hard disk; if a power failure occurs when work is saved only to memory, then the work will be lost. Hibernate will also return you to where you last left off within seconds.
Power Management 3 Password Protection Configuring the Power Buttons The power/sleep button (Fn + F4 key combo) and closed lid may be set to send the computer in to a power-saving state. It is recommended that you enable a password on wake up in order to protect your data. However you can disable this setting from the Power Options menu by clicking Require a password on wakeup in the left menu, and selecting the options (click Change settings that are currently unavailable).
Power Management Resuming Operation You can resume operation from power-saving states by pressing the power button, or in some cases pressing the sleep button (Fn + F4 key combo). Power Status Icon To Resume Color Power Off Off Press the Power Button Sleep Blinking Green Press the Power Button Closing the Lid If you have chosen to send the computer to Sleep when the lid is closed, raising the lid will wake the system up.
Power Management 3 Low Battery Warning When the battery is critically low, immediately connect the AC/DC adapter to the computer or save your work, otherwise, the unsaved data will be lost when the power is depleted. Battery Information Please follow these simple guidelines to get the best use out of your battery. Battery Power Your computer’s battery power is dependent upon many factors, including the programs you are running, and peripheral devices attached. You can set actions to be taken (e.g.
Power Management Conserving Battery Power • Use a power plan that conserves power (e.g Power saver), however note that this may have an affect on computer performance. • Lower the brightness level of the LCD display. The system will decrease LCD brightness slightly to save power when it is not powered by the AC/DC adapter. • Reduce the amount of time before the display is turned off. • Close wireless, Bluetooth, modem or communication applications when they are not being used.
Power Management Battery Life Battery life may be shortened through improper maintenance. To optimize the life and improve its performance, fully discharge and recharge the battery at least once every 30 days. 3 We recommend that you do not remove the battery yourself. If you do need to remove the battery for any reason see “Removing the Battery” on page 6 - 3. New Battery Always completely discharge, then fully charge, a new battery (see “Battery FAQ” on page 3 - 14 for instructions on how to do this).
Power Management Proper handling of the Battery Pack • DO NOT disassemble the battery pack under any circumstances • DO NOT expose the battery to fire or high temperatures, it may explode • DO NOT connect the metal terminals (+, -) to each other Damaged Battery Warning Should you notice any physical defects (e.g. the battery is bent out of shape after being dropped), or any unusual smells emanating from the notebook battery, shut your computer down immediately and contact your service center.
Power Management Battery FAQ How do I completely discharge the battery? Use the computer with battery power until it shuts down due to a low battery. Don’t turn off the computer even if a message indicates the battery is critically low, just let the computer use up all of the battery power and shut down on its own. 3 1. 2. 3. Figure 3 - 7 Power Plan Create 3 - 14 Battery Life Save and close all files and applications. Create a power plan for discharging the battery and set all the options to Never.
Power Management 4. 5. Scroll down to Battery and click + to expand the battery options.
Power Management How do I fully charge the battery? When charging the battery, don’t stop until the LED charging indicator light changes from orange to green. 3 How do I maintain the battery? Completely discharge and charge the battery at least once every 30 days or after about 20 partial discharges.
Drivers & Utilities Chapter 4: Drivers & Utilities This chapter deals with installing the drivers and utilities essential to the operation or improvement of some of the computer’s subsystems. The system takes advantage of some newer hardware components for which the latest versions of most available operating systems haven’t built in drivers and utilities. Thus, some of the system components won’t be auto-configured with an appropriate driver or utility during operating system installation.
Drivers & Utilities Driver Installation Insert the Device Drivers & Utilities + User’s Manual DVD-ROM and click Install Drivers (button), or click Optional (button) to access the Optional driver menu. 4 1. 2. If you wish to install the drivers manually see page 4 - 3. 3. Check the driver installation order from Table 4 - 1, on page 4 - 3 (the drivers must be installed in this order) which is the same as that listed in the Drivers Installer menu below.
Drivers & Utilities Manual Driver Installation To install the drivers manually click the Browse CD button in the Drivers Installer application and browse to the executable file in the appropriate driver folder.
Drivers & Utilities 4 Updating/Reinstalling Individual Drivers User Account Control (Win Vista) If you wish to update/reinstall individual drivers it may be necessary to uninstall the original driver.To do this go to the Control Panel in the Windows OS and double-click the Programs and Features icon (Programs > Uninstall a program). Click to select the driver (if it is not listed see below) and click Uninstall, and then follow the on screen prompts (it may be necessary to restart the computer).
Drivers & Utilities Driver Installation Procedure Video (VGA) 1. Click 1.Install Video Driver > Yes. 2. Click Next. 3. Click Finish to restart the computer. Audio 1. Click 2. Install Audio Driver > Yes. 2. Click Next. 3. Click Finish to restart the computer. Modem 1. Click 3.Install Modem Driver > Yes. 2. Click OK. 3. The modem is now ready for configuration.
Drivers & Utilities 4 Card Reader/ExpressCard 1. Click 5.Install CardReader Driver > Yes. 2. Click Next. 3. Click the button to accept the license, and then click Next. 4. Click Finish. Optional Drivers See the pages indicated for the driver installation procedures for any modules included in your purchase option. Ap-Key Utility 1. Click 6.Install AP-key Utility > Yes. 2. Click Next. 3. Click Finish to restart the computer. 4.
Drivers & Utilities Intel Matrix PC Camera This driver is only required if you have set up your hard disks in RAID or AHCI modes (see “Setting Up SATA RAID or AHCI Modes” on page 7 - 2). See the camera instructions in “PC Camera Driver Application” on page 7 - 17. TV Tuner Wireless LAN See the appropriate install procedure for your WLAN module in “Intel WLAN Driver Installation” on page 7 - 8. See the install procedure in “Mini-PCI TV Tuner Module” on page 7 - 25.
Drivers & Utilities 4 4 - 8
BIOS Utilities Chapter 5: BIOS Utilities Overview This chapter gives a brief introduction to the computer’s built-in software: PhoenixBIOS Setup Utility If your computer has never been set up, or you are making important changes to the system (e.g. hard disk setup), then you should review this chapter first and note the original settings found in the PhoenixBIOS Setup Utility. Even if you are a beginner, keep a record of the settings you find and any changes you make.
BIOS Utilities POST Screen 5 1.BIOS information 2.CPU type 3.Memory status 4.Enter Setup prompt appears only during POST Note: The POST screen as pictured is for guideline purposes only. Figure 5 - 1 POST Screen The Power-On Self Test (POST) Each time you turn on the computer, the system takes a few seconds to conduct a POST, including a quick test of the on-board RAM (memory). As the POST proceeds, the computer will tell you if there is anything wrong.
BIOS Utilities Failing the POST Errors can be detected during the POST. There are two categories, “fatal” and “nonfatal”. Fatal Errors These stop the boot process and usually indicate there is something seriously wrong with your system. Take the computer to your service representative or authorized service center as soon as possible. Non-Fatal Errors This kind of error still allows you to boot.
BIOS Utilities The Setup Program The Phoenix Setup program tells the system how to configure itself and manage basic features and subsystems (e.g. port configuration). Entering Setup 5 To enter the PhoenixBIOS Setup Utility, turn on the computer and press F2 during when you see the prompt "Press F2 to Enter Setup", which is usually present for a few seconds after you turn on the system. If you get a “Keyboard Error”, (usually because you pressed F2 too quickly) just press F2 again.
BIOS Utilities Setup Screens The following pages contain additional advice on portions of the Setup. Setup Menus Along the top of the screen is a menu bar with menu headings. When you select a heading, a new screen appears. Scroll through the features listed on each screen to make changes to Setup. Instructions on how to navigate each screen are in the box along the bottom of the screen.
BIOS Utilities Main Menu Phoenix TrustedCore(tm) Setup Utility Figure 5 - 2 Main Menu Main Main Advanced Security Boot Exit Item Specific Help System Time: System Date: 5 [08:11:05] [03/05/2007] SATA Port 1 SATA Port 2 SATA Port 3 [None] [60012MB SATA2] [None] IDE Channel 0 [CD-ROM] Installed memory Available to OS Used by devices F1 Esc Help Exit , , or selects field.
BIOS Utilities SATA Port 1/2/3: (Main Menu) Pressing Enter opens the sub-menu to show the configuration of hard disks on the computer’s SATA ports. Use the Auto (Type:) setting to have the items configured automatically for you. IDE Channel 0 (Main Menu) Pressing Enter here opens the sub-menu to show the configuration of the CD/DVD device(s) on the computer’s IDE Channel. Use the Auto (Type:) setting to have the items configured automatically for you.
BIOS Utilities RAID/AHCI Enable/Disable Warning 5 DO NOT Enable/Disable SATA RAID or SATA AHCI unless you intend to reinstall your operating system. Make sure you have backed up all your data before doing so. Figure 5 - 3 Advanced Menu Advanced Menu Phoenix TrustedCore(tm) Setup Utility Advanced Advanced Main Security Boot Exit Item Specific Help Setup Warning Setting items on this menu to incorrect values may cause your system to malfunction.
BIOS Utilities Reset Configuration Data: (Advanced Menu) This item is set to No as default. You can change the setting to Yes if you have installed a new add-on which has reconfigured the system, resulting in such a serious system conflict that the operating system is unable to boot.
BIOS Utilities Security Menu 5 The changes you make here affect the access to the Setup utility itself, and also access to your machine as it boots up after you turn it on. These settings do not affect your machine or network passwords which will be set in your software OS.
BIOS Utilities Password on boot: (Security Menu) Specify whether or not a password should be entered to boot the computer. If “Enabled” is selected, only users who enter a correct password can boot the system (see the warning in the sidebar). The default setting is “Disabled”. Note: To clear existing passwords press Enter and type the existing password, then press Enter for the new password (without typing any password entry) and Enter again to confirm the password clearance.
BIOS Utilities Boot Menu Phoenix TrustedCore(tm) Setup Utility Figure 5 - 5 Main Advanced Security Boot Exit Boot Menu Item Specific Help 5 F1 Esc Help Exit Select Item Select Menu -/+ Enter Boot priority order: 1: USB FDC: 2: USB KEY: 3: PCI SCSI: 4: IDE HDD: TOSHIBA MK6034GSX-(S2) 5: IDE CD: Optiarc DVD RW AD-7530A-(S 6: PCI BEV: Relatek Boot Agent 7: 8: Excluded from boot order: : All IDE HDD: : All IDE CDROM: : All USB Floppy: : All USB KEY: : All USB HDD: : USB CDROM: : All USB
BIOS Utilities Exit Menu Phoenix TrustedCore(tm) Setup Utility Main Advanced Security Boot Figure 5 - 6 Exit Menu Exit Item Specific Help Exit Saving Changes Exit Discarding Changes Load Setup Defaults Discard Changes Save Changes F1 Esc Help Exit Select Item Select Menu Exit System Setup and save your changes to CMOS.
BIOS Utilities 5 5 - 14
Upgrading The Computer Chapter 6: Upgrading The Computer Overview This chapter contains information on upgrading the computer. Follow the steps outlined to make the desired upgrades. If you have any trouble or problems you can contact your service representative for further help.
Upgrading The Computer When Not to Upgrade Power Safety Warning 6 Before you undertake any upgrade procedures, make sure that you have turned off the power, and disconnected all peripherals and cables (including telephone lines). It is advisable to also remove your battery in order to prevent accidentally turning the machine on. These procedures involve opening the system’s case, adding and sometimes replacing parts.
Upgrading The Computer Removing the Battery If you are confident in undertaking upgrade procedures yourself, for safety reasons it is best to remove the battery. 1. 2. 3. Turn the computer off, and turn it over. Loosen screws 1 - 3 . Release the battery, and lift the battery 4 out of the battery bay. 1 Warranty Warning Please check with your service representative before undertaking any upgrade procedures to find out if this will VOID your warranty.
Upgrading The Computer HDD System Warning 6 New HDD’s are blank. Before you begin make sure: You have backed up any data you want to keep from your old HDD. You have all the CD-ROMs and FDDs required to install your operating system and programs. If you have access to the internet, download the latest application and hardware driver updates for the operating system you plan to install. Copy these to a removable medium.
Upgrading The Computer 4. 5. 6. 7. 8. Remove screws 6 - 8 and lift the hard disk assembly out of the computer. Remove screws 9 - 16 . Separate the hard disk(s) from the bracket 17 and connector cable 18 . Insert the new hard disk into the computer. Re-Insert the bracket and insert screws.
Upgrading The Computer Removing the Hard Disk(s) in the Secondary HDD Bay 1. 2. 3. 4. 5. 6. 6 Turn off the computer, and turn it over and remove the battery. The secondary hard disk bay is located under the battery compartment. Remove screw 19 . Slide the hard disk assembly in the direction of the arrow 20 . Lift the hard disk assembly 21 out of the compartment. Remove the screws to release the hard disk from the case.
Upgrading The Computer Upgrading the System Memory (RAM) The computer has two memory sockets for 200 pin Small Outline Dual In-line (SODIMM) DDR II (DDR2) type memory modules (see “Memory” on page C - 3). The total memory size is automatically detected by the POST routine once you turn on your computer. 1. 2. 3. Turn off the computer, and turn it over and remove the battery. Locate the component cover and remove screws 1 - 10 . Remove the bay cover 11 .
Upgrading The Computer 4. Remove screws 12 - 14 from the RAM fan. Figure 6 - 6 12 RAM Fan Screws 6 13 5. Remove the RAM fan 15 .
Upgrading The Computer 6. 7. Gently pull the two release latches ( 16 & 17 ) on the sides of the memory socket in the direction indicated by the arrows in Figure 6 - 8 The RAM module 18 will pop-up, and you can remove it. 17 18 16 8. 9. 10. 11. 12. 13. Pull the latches to release the second module if necessary. Insert a new module holding it at about a 30° angle and fit the connectors firmly into the memory socket. The module’s pin alignment will allow it to only fit one way.
Upgrading The Computer Upgrading the Optical (CD/DVD) Device(s) 1. 2. 3. 4. Turn the computer off, turn it over and remove the battery. Locate the hard disk bay cover and remove screws 1 - 4 . Remove the bay cover 5 . Remove screw 6 and use the screwdriver to push the optical device(s) out of the computer at point 7 .
Upgrading The Computer Upgrading the Video Card If you intend to upgrade or add another VGA card follow the procedures outlined here. However please check with your service representative first to make sure your computer can support more than one video card, and that you are not going to void your warranty. Pay careful attention to the alignment of any video card into the slot on the mainboard. 1. 2. 3. Turn off the computer, and turn it over and remove the battery.
Upgrading The Computer 4. 5. Remove screws 12 - 14 from the video card fan. Disconnect the fan cable 15 . Figure 6 - 11 Video Card Fan Screws 14 15 6 12 13 6. Remove the video card fan 16 .
Upgrading The Computer 7. 8. 9. Remove screws 17 - 20 from the video card heatsink in the order indicated on the label. Remove screws 21 & 22 . Grip the handle and carefully remove the heatsink 23 . 18 Caution The heat sink, and video card area in general, contains parts which are subject to high temperatures. Allow the area time to cool before removing these parts.
Upgrading The Computer 10. Remove screw 24 from the video card. 11. Carefully remove the video card 25 .
Upgrading The Computer Installing a New Video Card 1. Prepare to fit the video card into the slot by holding it at about a 30° angle. Contact Warning Be careful not to touch the metal pins on the VGA card’s connecting edge. Even the cleanest hands have oils which can attract particles, and degrade the module’s performance. Figure 6 - 15 Video Card Insertion 2.
Upgrading The Computer 3. 4. Fit the connectors firmly into the socket, straight and evenly. DO NOT attempt to push one end of the card in ahead of the other. 5. The card’s pin alignment will allow it to only fit one way. Make sure the module is seated as far into the socket as it will go (none of the gold colored contact should be showing). DO NOT FORCE the card; it should fit without much pressure.
Upgrading The Computer 6. 7. 8. 9. Secure the card with screw 24 (Figure 6 - 14 on page 6 - 14). Place the heatsink back on the card, and secure the screws in the order indicated in Figure 6 - 13 on page 6 - 13. Attach the video card fan and secure with the screws as indicated in Figure 6 - 11 on page 6 - 12. Reinsert the component bay cover, and secure with the screws as indicated in Figure 6 - 10 on page 6 - 11.
Upgrading The Computer 6 6 - 18
Modules Chapter 7: Modules Overview This chapter contains the information on the various modules (some of which are optional) which may come with your computer, depending on the configuration purchased. If you are unsure please contact your service representative.
Modules Setting Up SATA RAID or AHCI Modes AHCI Mode Advanced Host Controller Interface (AHCI) is an interface specification that allows the storage driver to enable advanced serial ATA features such as Native Command Queuing (for maximum hard disk efficiency and performance). AHCI mode can be supported by one, two or three hard disks.
Modules RAID Level Description RAID 0 Identical drives reading and writing data in parallel to increase performance. RAID 0 implements a striped disk array and the data is broken into blocks and each block is written to a separate disk drive. RAID 1 Identical drives in a mirrored configuration used to protect data. Should a drive that is part of a mirrored array fail, the mirrored drive (which contains identical data) will handle all the data.
Modules SATA RAID or AHCI Setup Procedure (BIOS) 1. 2. Start-up your notebook computer and press to enter the BIOS. Go to the Advanced menu, select "SATA Mode" and press Enter. • For RAID Mode: - Set "SATA Mode" (“SATA Mode: (Advanced Menu)” on page 5 - 8) to "RAID". OR • For AHCI Mode: - Set "SATA AHCI Enable" (“SATA Mode: (Advanced Menu)” on page 5 - 8) to "AHCI". 3. 4. 7 5. 6. 7. Press Esc and go to the Boot menu.
Modules RAID Setup (Intel Matrix) 1. Press Ctrl + i to enter RAID configuration menu. Intel(R) Matrix Storage Manager option ROM v6.1.0.1002 ICH8R wRAID5 Copyright (C) 2003-06 Intel Corporation. All Rights Reserved. [ MAIN MENU 1. 2. 3. 4.
Modules 10. This will now return to the main menu. Figure 7 - 2 Intel(R) Matrix Storage Manager option ROM v6.0.0.1022 ICH8R wRAID5 Copyright (C) 2003-06 Intel Corporation. All Rights Reserved. [ MAIN MENU RAID Created 1. 2. 3. 4.
Modules Intel Matrix Make sure you install the Intel matrix driver and application if you have set up your hard disk(s) in AHCI or RAID modes. Intel Matrix Driver Installation 1. Click 1.Install Intel Matrix > Yes. 2. Click Next > Next > Yes > Next. 3. Click Finish to restart the computer. The Intel Matrix Storage Console displays status information on your RAID configuration. Run the Intel Matrix Storage Console from the Programs/All Programs menu.
Modules Wireless Device Operation Aboard Aircraft 7 The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the module(s) are OFF if you are using the computer aboard aircraft. Use the Fn + F11 key combination to toggle power to the WLAN module, and check the indicator to see if the module is powered on or not (see Table 1 - 5, on page 1 - 9). Wireless LAN Module If you have included an Intel PRO/Wireless 3945ABG (802.
Modules Connecting to a Wireless Network 1. Click the taskbar wireless icon , and then click Connect to a network (or rightclick the icon , and then click Connect to a network). Figure 7 - 4 Click icon 2. 3. Right-click icon In the Show list, click to choose Wireless from the drop-down menu. A list of currently available networks will appear.
Modules 4. 5. Click a network, and then click Connect. If you do not see a network you want to connect to, click Set up a connection or network (a list of options will appear allowing manual searching, and creating a new network). 6. Move the cursor over the taskbar icon Figure 7 - 6 Connecting 7 Figure 7 - 7 Connection Status 7 - 10 Wireless LAN Module to see the connection status (see below).
Modules 7. To disconnect from the wireless network you can click the taskbar wireless icon , and then select Connect or disconnect to access the network menu, and click Disconnect (or right-click the icon , and then click Disconnect from). Click icon Security Enabled Networks You should try to make sure that any network you are connecting to is a secure network. Connecting to unsecure networks may allow unauthorized access to your computer, documents, websites and files etc.
Modules Wireless Device Operation Aboard Aircraft 7 The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the module(s) are OFF if you are using the computer aboard aircraft. Use the Fn + F12 key combination to toggle power to the Bluetooth module, and check the indicator to see if the module is powered on or not (see Table 1 - 5, on page 1 - 9).
Modules User Guides & Help View the BlueSoleil User Guides from the Help Menu (or press the F1 key) in the IVT Corporation BlueSoleil Main Window control panel. Click the Help menu and select Contents and Index. Look through Getting Started or select the appropriate User Guide from the Contents menu.
Modules Disconnecting In order to have the Local Area Connection icon display the correct connection status, you will need to exit the IVT Corporation BlueSoleil - Main Window by clicking the File menu and selecting Exit (see over). 7 Bluetooth Local Area Connection You can check the Bluetooth connection status from the Network and Sharing Center: 1. 2. 3. 4. 5. 6. Use the Fn + F12 key combination to turn on the Bluetooth module.
Modules 8. 9. Do not use the close button or Fn + F12 key combination before clicking File > Exit or the correct status will not be displayed. You can then use the Fn + F12 key combination to turn off the Bluetooth module (check the LED icon for the Bluetooth module power status).
Modules PC Camera Module If you have included the PC Camera module in your purchase option, you will have the appropriate application provided on the Device Drivers & Utilities + User’s Manual DVD-ROM. There are 2 camera options available for this computer, depending on your purchase configuration. The 1.3M pixel camera module uses the BisonCap application to capture video files. The 2.0M pixel camera module uses the Video View application to capture video files. Make sure the PC Camera is on.
Modules PC Camera Driver Application 1. Make sure the module is powered on, and then insert the Device Drivers & Utilities + User’s Manual DVD-ROM into the CD/DVD drive. 2. Click Optional, and then click 4.PC Camera, Web cam > Yes. For the 1.3M Pixel Camera Module: 3. Choose the language you prefer and click Next > Next. 4. Click Finish to restart the computer. 5.
Modules PC Camera Audio Setup PC Camera & TV Tuner 7 If you have the optional TV Tuner included in your purchase, make sure you select which device to use with the BisonCap/Video View program. Go to the Devices menu and select the Bison Cam, NB Pro/ USB2.0 2M WebCam. If you wish to capture video & audio with your camera, it is necessary to setup the audio recording options in Windows. 1. 2. 3. 4. Click Start, and click Control Panel (or point to Settings and click Control Panel).
Modules Figure 7 - 12 Audio Setup for PC Camera Right-click 7 PC Camera Module 7 - 19
Modules Pre-Allocating File Space You may pre-allocate the file size for the capture file in the BisonCap program. You can choose to ignore this by clicking Cancel. 7 Pre-allocating space on the hard disk can improve the capture quality (particularly of large capture files), by reducing the amount of work the hard disk has to do in finding space for the video data as it is being captured. BisonCap (for 1.
Modules Eliminating Screen Flicker (BisonCap) If you find that the video screen in the BisonCap program is flickering, you can try to adjust the setting in the Video Capture Filter options. 1. 2. 3. Run the BisonCap program. Go to Options and scroll down to select “Video Capture Filter...”. Click either 50Hz or 60Hz under Frequency in Property Page (tab).
Modules Pre-Allocating File Space You may pre-allocate the file size for the capture file in the Video View program. 7 Pre-allocating space on the hard disk can improve the capture quality (particularly of large capture files), by reducing the amount of work the hard disk has to do in finding space for the video data as it is being captured. Video View (for 2.0M pixel camera module) Video View is a video viewer useful for general purpose video viewing and testing, and can capture video files to .
Modules Eliminating Screen Flicker (Video View) If you find that the video screen in the Video View program is flickering, you can try to adjust the setting in the Video Capture Filter options. 1. 2. 3. Run the Video View program. Go to Options and scroll down to select Video Capture Filter.... Click either 50Hz or 60Hz under Flickering Reduction in Image (tab).
Modules Zoom (Video View) If you have enabled digital zoom when installing the 2.0M Pixel Camera driver you may use the Options > Setting menu to zoom the camera in and out. Figure 7 - 15 Setting 1. 2. 3. Run the Video View program. Go to Options and scroll down to select Setting. Use the slider to adjust the zoom level, and click OK to save the setting. Snapshot Folder 7 The Snapshot folder’s default location is on the desktop.
Modules Mini-PCI TV Tuner Module A CD containing drivers, software and a user guide will be supplied if your purchase configuration includes the optional Mini-PCI TV Tuner module. The MPC788 module features both Analog and Hybrid (Analog & Digital) options; the MPC718 is a Hybrid module. You will also be supplied with a remote control unit and appropriate antenna and fittings for the Mini-PCI TV Tuner module.
Modules TV Tuner Module Support 7 Note that the TV Tuner module options in Windows Vista are supported by the Windows Media Center software which comes built-in to the Windows Vista Home Premium and Ultimate Editions only. If your purchase includes a TV Tuner option, and you are reconfiguring your system for a different system, you should install either Windows Home Premium or Ultimate Editions only. MPC788/MPC718 Driver & Software 1. Insert the MPC788 or MPC718 driver CD-ROM into the CD/DVD drive. 2.
Modules MPC718 Module 1. This TV Tuner module is fully supported by Windows Media Center in Windows Vista (Home Premium Edition & Ultimate Edition). 2. Run Windows Media Center directly from the Start menu (Start > Programs > Windows Media Center). 3. Windows Help and Support provides information on the Windows Media Center functions. Click Start and select Help and Support, and then type “Media Center” in the Search Help box and click the magnifying glass icon to bring up the results.
Modules Digital TV Broadcast Signal CATV Cable Safety Make sure that your CATV system installer has connected the Coaxial cable shield to the grounding system of the building, as close to the point of cable entry as practical. 7 This reminder is provided to call the CATV system installer’s attention to Article 820-93 of the NEC (Section 54, Part I of the Canadian Electrical Code). The antenna is the most crucial factor in receiving a clear digital terrestrial TV broadcast signal.
Modules 1. Mute 2. Teletext 3. 4. Home Power Button 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22.
Modules 7 7 - 30
Troubleshooting Chapter 8: Troubleshooting Overview Should you have any problems with your computer, before consulting your service representative, you may want to try to solve the problem yourself. This chapter lists some common problems and their possible solutions. This can’t anticipate every problem, but you should check here before you panic. If you don’t find the answer in these pages, make sure you have followed the instructions carefully and observed the safety precautions in the preface.
Troubleshooting Basic Hints and Tips Many of the following may seem obvious but they are often the solution to a problem when your computer appears not to be working. • Power - Is the computer actually plugged into a working electrical outlet? If plugged into a power strip, make sure it is actually working. Check the LED Power Indicators (see “LED Indicators” on page 1 - 7) to see the computer’s power status. • Connections - Check all the cables to make sure that there are no loose connections anywhere.
Troubleshooting Backup and General Maintenance • Always backup your important data, and keep copies of your OS and programs safe, but close to hand. Don’t forget to note the serial numbers if you are storing them out of their original cases, e.g. in a CD wallet. • Run maintenance programs on your hard disk and OS as often as you can. You may schedule these programs to run at times when you are not using your computer.
Troubleshooting Viruses • Install an Anti-Virus program and keep the definitions file (the file which tells your program which viruses to look for) up to date. New computer viruses are discovered daily, and some of them may seriously harm your computer and cause you to lose data. Anti-Virus programs are commercially available and the definitions file updates are usually downloadable directly from the internet. • Be careful when opening e-mail from sources you don’t know.
Troubleshooting Upgrading and Adding New Hardware/Software • Do not be tempted to make changes to your Windows Registry unless you are very sure of what you are doing, otherwise you will risk severely damaging your system. • Don’t open your computer or undertake any repair or upgrade work if you are not comfortable with what you are doing. • Read the documentation.
Troubleshooting • Don’t over complicate things. The less you have to deal with then the easier the source of the problem may be found; Example - if your computer has many devices plugged into its ports, and a number of programs running, then it will be difficult to determine the cause of a problem. Try disconnecting all of the devices and restarting the computer with all the peripheral devices unplugged.
Troubleshooting Problems & Possible Solutions Problem Possible Cause - Solution You turned the power on but it doesn’t work. Battery missing / incorrectly installed. Check the battery bay, make sure the battery is present and seated properly (the design of the battery only allows it to go in one way). Make sure there’s nothing interfering with the battery contacts. The Battery LED power indicator , is blinking orange. Low Battery. Plug in the AC power source.
Troubleshooting Problem Possible Cause - Solution The computer feels too hot. Make sure the computer is properly ventilated and the vents/fan intakes are not blocked. If this doesn’t cool it down, put the system into Hibernate mode or turn it off for an hour. Make sure the computer isn’t sitting on a thermal surface (see “Overheating” on page 1 - 13). Make sure you’re using the correct adapter.
Troubleshooting Problem Possible Cause - Solution Password Warning If you choose to set a boot password, NEVER forget your password. The consequences of this could be serious. If you cannot remember your boot password you must contact your vendor and you may lose all of the information on your hard disk. The sound cannot be heard or the volume is very low. The volume might be set too low.
Troubleshooting 8 Problem Possible Cause - Solution The system freezes or the screen goes dark. The system’s power saving features have timed-out. Use the AC/DC adapter, press a key on the keyboard, or press the sleep (Fn + F4) key combination, or press the power button if no LEDs are lit. The system never goes into a power saving mode. Power Options features are not enabled.
Interface (Ports & Jacks) Appendix A: Interface (Ports & Jacks) Overview The following chapter will give a quick description of the ports & jacks which allow your computer to communicate with external devices, connect to the internet etc.
Interface (Ports & Jacks) Ports and Jacks Item Card Reader Description The card reader allows you to use the following digital storage cards: MMC (MultiMedia Card) SD (Secure Digital) MS (Memory Stick) MS (Memory Stick Pro) Cable (CATV) Antenna Jack DC-In Jack A RS MMC (requires PC adapter) Mini SD (requires PC adapter) MS Duo (requires PC adapter) Use this jack to connect a CATV cable if you have included the optional Mini-PCI TV Tuner in your purchase.
Interface (Ports & Jacks) Item Description Headphone-Out Jack Headphones or speakers may be connected through this jack. Note: Set your system’s volume to a reduced level before connecting to this jack. Line-In Jack The Line-In jack allows you to play audio sources through the computer’s speakers. Note that audio input through Line-in will default to the mute setting. To set up your audio sources to play through the Line-in jack go to the Sound control panel and make sure the Mute box is not ticked.
Interface (Ports & Jacks) Item Description RJ-45 LAN Jack This port supports LAN (Network) functions. Note: Broadband (e.g. ADSL) modems usually connect to the LAN port. S/PDIF-Out Jack This S/PDIF (Sony/Philips Digital Interface Format) Out Port allows you to connect your DVDcapable PC to a Dolby AC-3 compatible receiver for “5.1” or ‘dts’ surround sound. Security Lock Slot To prevent possible theft, a Kensington-type lock can be attached to this slot. Locks can be purchased at any computer store.
NVIDIA Video Driver Controls Appendix B: NVIDIA Video Driver Controls The basic settings for configuring the LCD are outlined in “Video Features” on page 1 - 15. Video Card Options NVIDIA Video Driver Installation Make sure you install the drivers in the order indicated in Table 4 - 1, on page 4 - 3. 1. Insert the Device Drivers & Utilities + User’s Manual DVD-ROM into the CD/DVD drive. 2. Click 1.Install Video Driver > Yes. 3. Click Next. 4. Click Finish to restart the computer.
NVIDIA Video Driver Controls NVIDIA Control Panel To access the GeForce..... control panel from the desktop; right-click the desktop, then click NVIDIA Control Panel. B NVIDIA Control Panel More advanced video configuration options are provided in the NVIDIA Control Panel tab. 1. 2. 3. 4. Open the Display Settings (see page 1 - 16) control panel. Click Advanced Settings (button). Click GeForce..... (tab). Click Start the NVIDIA Control Panel to make any video adjustments. 1. 2.
NVIDIA Video Driver Controls The NVIDIA Control Panel provides additional video configuration controls and tools which allow quick access to features such as display configuration, 3D Settings and Help menus etc. Navigating the Control Panel Navigate through the control panels in much the same way as you would a web page. Click on the sub-heading tasks in the left menu (and on the highlighted links) for information. Use the buttons on the top left to go back, forward etc.
NVIDIA Video Driver Controls The Help menus provide index and search features, and direct links to the NVIDIA website etc.
NVIDIA Video Driver Controls SLI Multi GPU Configuration This computer features an NVIDIA Scalable Link Interface (SLI) that improves graphic quality and performance by combining dual NVIDIA GPUs in a single system. To enable/disable SLI Configuration: 3. 4. Go to NVIDIA Control Panel (see “NVIDIA Control Panel” on page B - 2). Double-click 3D Settings, and then click Set SLI Configuration.
NVIDIA Video Driver Controls SLI Multi GPU Configuration & Battery Power Note that due to the high power and system demands created by enabling SLI Configuration, you should not enable SLI configuration if your computer is powered by battery only. If you attempt to run an SLI configuration when the computer is powered by the battery only, then system problems may occur. • If the computer is currently powered by battery only do not enable SLI configuration.
NVIDIA Video Driver Controls Display Devices Besides the built-in LCD, you can also use an external monitor/flat panel display or TV as your display device. The following are the display options: 1. 2. 3. 4. The built-in LCD. An external monitor connected to the DVI-Out Port or external monitor port. A flat panel display connected to the DVI-Out Port (or external monitor port for older models). A TV connected to the S-Video-Out jack.
NVIDIA Video Driver Controls Attaching Other Displays Configuring an External Display in Windows Vista 1. 2. 3. Attach your external display to the external monitor port/DVI-Out Port and turn it on. If a New Display Detected window does not appear in Windows Vista, go to the Windows Mobility Center control panel (Mobile PC > Adjust commonly used mobility settings) and click Connect display.
NVIDIA Video Driver Controls Configuring an External Display using the NVIDIA Control Panel Alternatively you can use the NVIDIA control panel to configure any attached displays. 1. 2. 3. Attach your external display to the external monitor port/DVI-Out Port (or TV to the S-Video-Out jack), and turn it on. Go to NVIDIA Control Panel (see “NVIDIA Control Panel” on page B - 2). Double-click Display, and then click Set up multiple displays.
NVIDIA Video Driver Controls Blu-ray/HD-DVD Support B Display Modes Single Display Mode Only one of your displays is used. If your optical device drive option includes a Blu-ray/ HD-DVD device, please note the following: Clone Mode Clone Mode simply shows an exact copy of the Primary display desktop on the other display(s). This mode will drive multiple displays with the same content.
NVIDIA Video Driver Controls Using New Display Detected to Enable Extended Mode 1. 2. 3. 4. 5. Attach your external display to the external monitor port/DVI-Out Port (or TV to the S-Video-Out jack), and turn it on. If a New Display Detected window does not appear in Windows Vista, go to the Windows Mobility Center control panel (Mobile PC > Adjust commonly used mobility settings) and click Connect display. Click to select Show different parts of my desktop on each display (extended).
NVIDIA Video Driver Controls Using Display Settings to Enable Extended Mode 1. Display Settings Extended Desktop 2. Use the control panel to drag the monitors to match the physical arrangement you wish to use. 3. 4. You can drag any icons or windows across to either display desktop, which makes it possible to have one program visible in one of the displays, and a different program visible in the other display.
NVIDIA Video Driver Controls Enabling TV Display To display desktop images on a TV, connect the TV to your computer by using an S-Video cable from the TV to the S-Video-Out jack on the left of the computer. You will need to enable the TV display from the NVIDIA Control Panel as per the instructions on B - 9. The TV will appear as a display option (2. Select the displays you would like to use.) when attached to the S-Video-Out jack. Apply the settings, and then click Yes to save the changes.
NVIDIA Video Driver Controls Changing the TV Signal Format 1. 2. 3. 4. When the TV is enabled as a display device, click the sub-menus under Video & Television. Click “Change the signal or HD format” Select the TV signal format (the menu allows you to select TV format by country if you are unsure of your TV format). Apply the settings, and then click Yes to save the changes.
Specifications Appendix C: Specifications Latest Specification Information The specifications listed in this Appendix are correct at the time of going to press. Certain items (particularly processor types/ speeds and CD/DVD device types) may be changed, updated or delayed due to the manufacturer's release schedule. Check with your service center for details.
Specifications Feature Processor Types Core Logic Specification Intel® Core™ 2 Duo Processor LGA775 Package (775-pin) E6300/ E6400 65nm (65 Nanometer) Process Technology 2MB On-die L2 Cache & 1066MHz FSB 1.86/ 2.13 GHz Intel® Core™ 2 Duo Processor LGA775 Package (775-pin) E6600/ E6700 65nm (65 Nanometer) Process Technology 4MB On-die L2 Cache & 1066MHz FSB 2.40/ 2.
Specifications Feature LCD Specification 17.
Specifications Feature Video Card Video Card Options Note that card types, specifications and drivers are subject to continual updates and changes. Check with your service center for the latest details on video cards supported.
Specifications Feature Specification Card Reader Embedded 7-in-1 Card Reader (MS/ MS Pro/ SD/ Mini SD/ MMC/ RS MMC/ MS Duo) Note: MS Duo/ Mini SD/ RS MMC Cards Require a PC Adapter Audio UAA (Universal Audio Architecture) Integrated Azalia Compliant Interface S/PDIF Digital Output Built-In Microphone 4 * Built-In Speakers Keyboard & Pointing Device Full Size Winkey Keyboard with Numeric Keypad Two Game Hot Keys Built-In TouchPad (Scroll Functionality Included) ExpressCard Slot ExpressCard/34/54 S
Specifications Feature Communication Specification AZALIA MDC 56K Modem (V.90 & V.92 Compliant) USB 2.0 Bluetooth Class II Module (Option) 1GB PCIe Fast Ethernet LAN Module 1.3M/2.0M Pixel USB 2.0 PC Camera Module (Factory Option) Intel PRO/Wireless 3945ABG PCIe Wireless LAN Module (Option) Intel PRO/Wireless 4965AGN PCIe Wireless LAN Module (Option) Operating Systems Supported Windows XP SP2 Windows Vista 64bit Home Premium/ Business/ Enterprise/ Ultimate Power Management Supports ACPI 2.
Specifications Feature Physical Dimensions & Weight Optional Specification 397mm (w) * 298mm (d) * 51 ~ 60mm (h) 5.4kg Optical Drive Module Options: Intel PRO/Wireless 3945ABG PCIe Wireless LAN Module Intel PRO/Wireless 4965AGN PCIe Wireless LAN Module Combo Drive Module DVD-DUAL Module DVD-Super Multi Drive Module Blu-ray Drive Module HD-DVD Drive Module USB 2.0 Bluetooth Class II Module External USB 1.44MB Floppy Disk Drive 1.3M/2.0 Pixel USB 2.
Specifications C C - 8
Windows XP Information Appendix D: Windows XP Information This Appendix contains information (including control panel information, driver installation etc.) for users of the Windows XP OS.
Windows XP Information DVD Regional Codes Changing DVD Regional Codes Go to the Control Panel and double-click System > Hardware (tab), click Device Manager, then click the + next to DVD/CD-ROM drives. Double-click on the DVD-ROM device to bring up the Properties dialogue box, and select the DVD Region (tab) to bring up the control panel to allow you to adjust the regional code. DVD region detection is device dependent, not OS-dependent. You can select your module’s region code 5 times.
Windows XP Information Windows XP Start Menu & Control Panel Most of the control panels, utilities and programs within Windows XP (and most other Windows versions) are accessed from the Start menu. When you install programs and utilities they will be installed on your hard disk drive, and a shortcut will usually be placed in the Start menu and/or the desktop. You can customize the look of the Start menu by right-clicking the Start menu and selecting Properties from the menu.
Windows XP Information Sound Volume Adjustment How high the sound volume can be set depends on the setting of the volume control within Windows (and the volume control function keys on the computer). Click the Volume icon on the taskbar to check the setting. Figure D - 3 D Realtek Audio Configuration Menus D - 4 Audio Features Audio Features You can configure the audio options on your computer from the Sounds and Audio Devices Windows control panel.
Windows XP Information Application Hot Key The hot key buttons give instant access to the default Internet browser and e-mail program, and to a user-defined application, with one quick button press. To configure a program to open when the application hot key is pressed (Windows Media Player is the default program), follow the instructions below (make sure you install the Ap-Key Utility driver - see “TouchPad” on page D - 29). 1. Right click the Hot Key driver icon in the taskbar. 2.
Windows XP Information Game Keys The two game hot keys on the left of the computer allow macros to be configured for common keystrokes used in applications (the keys can assigned macros for any program, not only games). To configure the keys follow the instructions below. 1. Run the Game Key Configuration program from the desktop icon (or from C:\Windows\CleGameKey\GmKeyCfgUtl.exe). 2. Double-click the button for the appropriate key (it will turn red ). 3.
Windows XP Information Video Features You can switch display devices, and configure display options, from the Display Properties control panel in Windows as long as the appropriate video driver is installed. To access Display Properties in Windows: 1. 2. 3. 4. Click Start, point to Settings and click Control Panel (or just click Control Panel). Double-click Display (icon) - In the Appearances and Themes category. Click Settings (tab) in the Display Properties dialog box.
Windows XP Information Display Properties 2 1 3 Figure D - 6 - Display Properties & NVIDIA Control Panel Video Card Options Note that card types, specifications and drivers are subject to continual updates and changes. This computer features an NVIDIA Scalable Link Interface (SLI) that improves graphic quality and performance by combining dual NVIDIA GPUs in a single system for some of the video card options.
Windows XP Information Display Devices & Options Besides the built-in LCD, you can also use an external VGA monitor (CRT)/external Flat Panel Display or TV as your display device. A VGA monitor/Flat Panel Display connects to the DVI-Out port or external monitor port; a TV to the S-Video-Out jack. The following display modes are available. Display Mode Description Note Single Display Mode Only one of your displays is used.
Windows XP Information SLI Configuration & Multiple Displays Note that if SLI configuration is enabled only a Single display may be used as the display device. SLI Multi GPU Configuration This computer features an NVIDIA Scalable Link Interface (SLI) that improves graphic quality and performance by combining dual NVIDIA GPUs in a single system. To enable/disable SLI Configuration: 1. Go to NVIDIA Control Panel (see “Video Features” on page B - 7). 2.
Windows XP Information Control Panels (NVIDIA) The NVIDIA Control Panel provides additional video configuration controls and tools which allows quick access to features such as display configuration, appearance, mobile support and Help menus etc. Navigating the Control Panel Navigate through the control panels in much the same way as you would a web page. Click on the headings, menus and highlighted links for information. Use the buttons on the top left to go back, forward etc.
Windows XP Information Function Key Combination You can use the Fn + F7 key combination to toggle through the display options: Attaching Other Displays 1. Attach your external display to the external monitor port/DVI-Out Port (or TV to the SVideo-Out jack), and turn it on. 2. Go to NVIDIA Control Panel (see “Video Features” on page B - 7). 3. Click Set up multiple displays (Display). 4. Select the display mode and displays you want to use from the menu. 5.
Windows XP Information 7. Click Change Resolution (Display) to adjust the display resolution for any attached displays. 8. Click the display icon and use the sliders to adjust the resolution. 9. Click Apply (and Yes to confirm the settings change).
Windows XP Information To Enable Windows Extended Desktop 1. Attach your external monitor to the external monitor port and turn it on. 2. Click Start, point to Settings (or click Control Panel) and click Control Panel (if you are in Category View choose Appearance and Themes). 3. Double-click Display (icon). 4. Click Settings (tab). 5. Click the monitor icon (e.g. 2 ), and make sure you have checked “Extend my Windows desktop onto this monitor.” and click Apply.
Windows XP Information Enabling TV Display To display desktop images on a TV, connect the TV to your computer by using an SVideo cable from the TV to the S-Video-Out jack on the left of the computer. You will need to enable the TV display from the NVIDIA Control Panel as per the instructions on D - 12. The TV will appear as a display option (2. Select the displays you would like to use.) when attached to the S-Video-Out jack. Apply the settings, and then click Yes to save the changes.
Windows XP Information Changing the TV Signal Format 1. 2. 3. 4. D When the TV is enabled as a display device, click the sub-menus under Video & Television. Click “Change the signal or HD format” Select the TV signal format (the menu allows you to select TV format by country if you are unsure of your TV format). Apply the settings, and then click Yes to save the changes.
Windows XP Information Power Management Features The Power Options control panel icon in Windows (see page D - 3) allows you to configure power management features for your computer. You may conserve power through individual components such as the monitor or hard disk, or you may use either Stand by or Hibernate mode to conserve power throughout the system. Power Schemes You can set your computer to conserve power through individual components by means of Power Schemes.
Windows XP Information Each Windows Power Scheme will also adjust the processor performance of your machine in order to save power. This is worth bearing in mind if you are experiencing any reduced performance (especially under DC/battery power). Choose the Home/Office Desk scheme for maximum performance when the computer is powered from an AC power source.
Windows XP Information Stand by Stand by saves the least amount of power, but takes the shortest time to return to full operation. During Stand by the hard disk is turned off, and the CPU is made to idle at its slowest speed. All open applications are retained in memory. When you are not using your computer for a certain length of time, which you specify in the operating system, it will enter Stand by mode to save power.
Windows XP Information Configuring the Power Button The power button may be set to send the computer in to either Stand by or Hibernate mode. In Stand by mode, the LED will blink green. In Hibernate the LED will be off (battery) or orange (AC/DC adapter). If you are in a power saving mode set to save power through individual components (e.g. hard disk, monitor), the LED will remain green. Sleep Button You may also configure the Sleep/Resume key combination (Fn + F4).
Windows XP Information Battery Information Please follow these simple guidelines to get the best use out of your battery. New Battery Always completely discharge, then fully charge, a new battery (see “Battery FAQ” on page D - 24). Battery Life Your computer’s battery life is dependent upon many factors, including the programs you are running, and peripheral devices attached.
Windows XP Information Battery life may be shortened through improper maintenance. To optimize the life and improve its performance, fully discharge and recharge the battery at least once every 30 days. We recommend that you do not remove the battery yourself. If you do need to remove the battery for any reason see “Removing the Battery” on page 6 - 3.
Windows XP Information Proper handling of the Battery Pack • DO NOT disassemble the battery pack under any circumstances • DO NOT expose the battery to fire or high temperatures, it may explode • DO NOT connect the metal terminals (+, -) to each other Damaged Battery Warning Should you notice any physical defects (e.g. the battery is bent out of shape after being dropped), or any unusual smells emanating from the notebook battery, shut your computer down immediately and contact your service center.
Windows XP Information Battery FAQ How do I completely discharge the battery? Use the computer with battery power until it shuts down due to a low battery. Don’t turn off the computer by yourself even when you see a message that indicates the battery is critically low, just let the computer use up all of the battery power and shut down on its own.
Windows XP Information Driver Installation The Device Drivers & Utilities + User’s Manual DVD-ROM contains the drivers and utilities necessary for the proper operation of the computer. Table D - 3 lists what you need to install, and it is very important that the drivers are installed in the order indicated.
Windows XP Information What to Install D This section covers driver and utility installation instructions for Windows XP Home & Professional. Insert the Device Drivers & Utilities + User’s Manual DVDROM and click Install Drivers (button), or click Optional (button) to access the Optional driver menu. 1. Check the driver installation order from Table D - 3 (the drivers must be installed in this order) which is the same as that listed in the Drivers Installer menu below. 2.
Windows XP Information Updating/Reinstalling Individual Drivers If you wish to update/reinstall individual drivers it may be necessary to uninstall the original driver.To do this go to the Control Panel in the Windows OS and double-click the Add/Remove Programs item. If you see the individual driver listed (if not see below), uninstall it, following the on screen prompts (it may be necessary to restart the computer).
Windows XP Information Chipset 1. Click 1.Install Chipset Driver > Yes. 2. Click Next > Yes > Next. 3. Click Finish to restart the computer. Video 1. Click 2.Install Video Driver > Yes. 2. Click Next (click Continue Anyway if asked if you want to continue at any time). 3. Click “Yes, I want to restart my computer now” (button). 4. Click Finish to restart the computer. Audio 1. Click 3. Install Audio Driver > Yes. 2. Click Next (click Cancel if a Found New Hardware Wizard appears). 3.
Windows XP Information TouchPad 1. Click 6.Install Touchpad Driver > Yes. 2. Click Next > Next > Next. 3. Click Finish to restart your computer. Card Reader/ExpressCard 1. Click 7.Install CardReader Driver > Yes. 2. Click Next. 3. Click the button to accept the license, and then click Next. 4. Click Finish. Ap-Key Utility 1. Click 8.Install AP-key Utility > Yes. 2. Click Next. 3. The GameKey icon will appear on the desktop when the driver is installed. 4.
Windows XP Information Setting Up SATA RAID or AHCI Modes AHCI Mode Advanced Host Controller Interface (AHCI) is an interface specification that allows the storage driver to enable advanced Serial ATA features such as Native Command Queuing (for maximum hard disk efficiency and performance). AHCI mode can be supported by one, two or three hard disks.
Windows XP Information What to Prepare for RAID or AHCI Setup Prepare the following before setting up your serial ATA hard disks in RAID mode (to configure AHCI mode you do not need to prepare any extra hard disks but will need to install the Intel Matrix driver): 1. 2. 3. 4. 5. 6. An operable computer (to create a SATA RAID/AHCI driver diskette). An external USB floppy disk drive. A prepared formatted blank 3.5" 1.44MB floppy diskette.
Windows XP Information SATA RAID or AHCI Setup Procedure (BIOS) 1. 2. 3. 4. 5. 6. 7. 8. Go to the operable computer running Windows and insert a prepared formatted blank 3.5" 1.44MB floppy diskette. Insert the Device Drivers & Utilities + User’s Manual DVD-ROM into the CD/DVD drive of the operable computer. Click Start (menu) > Run... and navigate (Browse..) to D:\Others\00Raiddriver\F6flpy32.exe and click OK. Make sure the formatted blank 3.5" 1.44MB floppy diskette is inserted, and click OK.
Windows XP Information RAID Setup (Intel Matrix) 1. Press Ctrl + i to enter RAID configuration menu. Intel(R) Matrix Storage Manager option ROM v6.1.0.1002 ICH8R wRAID5 Copyright (C) 2003-06 Intel Corporation. All Rights Reserved. [ MAIN MENU 1. 2. 3. 4.
Windows XP Information 10. This will now return to the main menu. Figure D - 21 Intel(R) Matrix Storage Manager option ROM v6.0.0.1022 ICH8R wRAID5 Copyright (C) 2003-06 Intel Corporation. All Rights Reserved. [ MAIN MENU RAID Created 1. 2. 3. 4.
Windows XP Information Windows Setup for RAID & AHCI Modes 13. Start the computer up, and press a key when you see the message "Press any key to boot from CD". 14. Press the F6 key when you see the message “Press F6 if you need to install third party SCSI or RAID driver”. 15. When the Windows Setup menu appears (Windows will load a number of files before the Setup menu appears), press the key to "Specify Additional Device". 16.
Windows XP Information Intel Matrix Driver Installation 1. Insert the Device Drivers & Utilities + User’s Manual DVD-ROM into the CD/DVD drive. 2. Click Optional. 3. Click 1.Install Intel Matrix > Yes. 4. Click Next > Next > Yes > Next 5. Click Finish to restart the computer. 6. Run the Intel(R) Matrix Storage Manager application from the Start > Programs/All Programs menu. Figure D - 23 - Intel Matrix Storage Console 7. The Intel(R) Matrix Storage Manager provides information on the RAID status.
Windows XP Information Intel WLAN Module Before installing the Intel PRO/Wireless 3945ABG (802.11a/b/g) or Intel PRO/Wireless 4965AGN (802.11a/g/n) WLAN driver use the Fn + F11 key combination to toggle power to the module. Intel WLAN Driver Installation 1. Make sure the module is powered on (use the Fn + F11 key combination to toggle power to the module), and then insert the Device Drivers & Utilities + User’s Manual DVD-ROM into the CD/DVD drive. 2. Click Optional, and then click 2.Wireless Lan > Yes.
Windows XP Information User Guide You can view the User Guides from the Device Drivers & Utilities + User’s Manual DVD-ROM. Click Optional and then click the Unlock button. Click 2.Wireless Lan > Yes. Click View User Guide (button).
Windows XP Information Bluetooth Module Before installing the Bluetooth driver use the Fn + F12 key combination to toggle power to the module. Bluetooth Driver Installation 1. Make sure the module is powered on and then insert the Device Drivers & Utilities + User’s Manual DVD-ROM into the CD/DVD drive. 2. Click Optional, and then click 3.Bluetooth > Yes. 3. Choose the language you prefer, and click OK. 4. Click Next. 5. Click the button to accept the license agreement, and then click Next. 6.
Windows XP Information User Guide View the BlueSoleil User Guides (Contents and Index) from the Help menu (or press the F1 key) in the IVT Corporation BlueSoleil - Main Window control panel. Click BlueSoleil User Guides in the Contents tab, and click to select the appropriate User Guide from the panel on the right.
Windows XP Information Bluetooth Local Area Connection Icon If you want to display the Local Area Connection icon for the Bluetooth connection in the taskbar, set it up as follows: 1. Access the Network Connections control panel in Windows (Start > Settings > Network Connections OR Start > Connect To > Show all Connections) or by clicking the taskbar icon . 2. Right-click the Bluetooth connection icon, and select Properties. 3.
Windows XP Information 5. 6. 7. Use the Fn + F12 key combination to turn on the Bluetooth module. Run the IVT Corporation BlueSoleil program from the desktop icon or Start menu. The connection status will then be displayed. Figure D - 27 - Bluetooth Connected 8. To disconnect click File from the IVT Corporation BlueSoleil - Main Window, and select Exit (the Local Area Connection will then display “A network cable is unplugged”). 9.
Windows XP Information PC Camera Module Before installing the PC Camera driver use the Fn + F10 key combination to toggle power to the module. There are 2 camera options available for this computer, depending on your purchase configuration. The 1.3M pixel camera module uses the BisonCap application to capture video files. The 2.0M pixel camera module uses the Video View application to capture video files.
Windows XP Information PC Camera Driver Installation 1. Make sure the module is powered on and then insert the Device Drivers & Utilities + User’s Manual DVD-ROM into the CD/DVD drive. 2. Click Optional, and then click 4.PC Camera, Web cam > Yes. For the 1.3M Pixel Camera Module: 3. Choose the language you prefer and click Next > Next. 4. Click Finish to restart the computer. 5.
Windows XP Information PC Camera Audio Setup If you wish to capture video & audio with your camera, it is necessary to setup the audio recording options in Windows (see Figure D - 29 on page D - 46). 1. Go to the Start menu and point to Settings (or just click Control Panel) and click Control Panel, then doubleclick the Sounds & Audio Devices icon (Sounds, Speech, and Audio Devices in Category View). 2. Click Advanced in the Volume > Device volume tab. 3.
Windows XP Information Figure D - 29 Audio Setup for PC Camera D D - 46 PC Camera Module
Windows XP Information BisonCap (for 1.3M pixel camera modules) BisonCap is a video viewer useful for general purpose video viewing and testing, and can capture video files to .avi format. 1. Run the BisonCap application from the Start > Programs/All Programs > BisonCam menu (it is recommended that you set the capture file before the capture process - see Set Capture File below). 2.
Windows XP Information Eliminating Screen Flicker (BisonCap) If you find that the video screen in the BisonCap application is flickering, you can try to adjust the setting in the Video Capture Filter options. 1.Run the BisonCap program. 2.Go to Options and scroll down to select “Video Capture Filter...”. 3.Click either 50Hz or 60Hz under Frequency in Property Page (tab).
Windows XP Information Video View (for 2.0M pixel camera module) Video View is a video viewer useful for general purpose video viewing and testing, and can capture video files to .avi format. 1. Run the Video View program from the Start > Programs/All Programs > USB2.0 PC Camera menu (it is recommended that you set the capture file before the capture process - see Set Capture File below). 2.
Windows XP Information Eliminating Screen Flicker (Video View) If you find that the video screen in the Video View program is flickering, you can try to adjust the setting in the Video Capture Filter options. 1. Run the Video View program. 2. Go to Options and scroll down to select Video Capture Filter.... 3. Click either 50Hz or 60Hz under Flickering Reduction in Image (tab).
Windows XP Information Zoom (Video View) If you have enabled digital zoom when installing the 2.0M Pixel Camera driver you may use the Options > Setting menu to zoom the camera in and out. 1. Run the Video View program. 2. Go to Options and scroll down to select Setting. 3. Use the slider to adjust the zoom level, and click OK to save the setting. Figure D - 32 Setting Snapshot Folder Still Image Capture (Video View) You can capture still images by using the Snapshot command from the Capture menu. 1.
Windows XP Information Mini-PCI TV Tuner Module The Mini-PCI TV Tuner Module driver and application (for MPC788/MPC718) are provided on a separate CDROM for Windows XP (see “Mini-PCI TV Tuner Module” on page 7 - 25 for further information). D MPC788/MPC718 Driver & Cyberlink PowerCinema Installation 1. Insert the driver MPC788 or MPC718 CD-ROM into the CD/DVD drive. 2. Click XP Setup. 3. Choose the Setup Language you prefer, and then click Next. 4. Click Next > Next. 5.
