electra
Preface Notice The company reserves the right to revise this publication or to change its contents without notice. Information contained herein is for reference only and does not constitute a commitment on the part of the manufacturer or any subsequent vendor. They assume no responsibility or liability for any errors or inaccuracies that may appear in this publication nor are they in anyway responsible for any loss or damage resulting from the use (or misuse) of this publication.
Preface R&TTE Directive This device is in compliance with the essential requirements and other relevant provisions of the R&TTE Directive 1999/5/EC. This device will be sold in the following EEA countries: Austria, Italy, Belgium, Liechtenstein, Denmark, Luxembourg, Finland, Netherlands, France, Norway, Germany, Portugal, Greece, Spain, Iceland, Sweden, Ireland, United Kingdom, Cyprus, Czech Republic, Estonia, Hungary, Latvia, Lithuania, Malta, Slovakia, Poland, Slovenia.
Preface CE Marking This device has been tested to and conforms to the regulatory requirements of the European Union and has attained CE Marking. The CE Mark is a conformity marking consisting of the letters “CE”. The CE Mark applies to products regulated by certain European health, safety and environmental protection legislation. The CE Mark is obligatory for products it applies to: the manufacturer affixes the marking in order to be allowed to sell his product in the European market.
Preface FCC Statement (Federal Communications Commission) You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Preface FCC RF Radiation Exposure Statement: 1. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. Warning Use only shielded cables to connect I/O devices to this equipment.
Preface IMPORTANT SAFETY INSTRUCTIONS Follow basic safety precautions, including those listed below, to reduce the risk of fire, electric shock, and injury to persons when using any electrical equipment: 1. 2. 3. 4. 5. Do not use this product near water, for example near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool. Avoid using this equipment with a telephone line (other than a cordless type) during an electrical storm.
Preface Instructions for Care and Operation The notebook computer is quite rugged, but it can be damaged. To prevent this, follow these suggestions: 1. Don’t drop it, or expose it to shock. If the computer falls, the case and the components could be damaged. Do not expose the computer to any shock or vibration. 2. Do not place it on an unstable surface. Do not place anything heavy on the computer. Keep it dry, and don’t overheat it.
Preface 3. Avoid interference. Keep the computer away from high capacity transformers, electric motors, and other strong magnetic fields. These can hinder proper performance and damage your data. 4. Follow the proper working procedures for the computer. Shut the computer down properly and don’t forget to save your work. Remember to periodically save your data as data may be lost if the battery is depleted. Do not turn off the power until you properly shut down all programs. 5.
Preface Power Safety The computer has specific power requirements: • Only use a power adapter approved for use with this computer. • Your AC/DC adapter may be designed for international travel but it still requires a steady, uninterrupted power supply. If you are unsure of your local power specifications, consult your service representative or local power company. • The power adapter may have either a 2-prong or a 3-prong grounded plug.
Preface Polymer Battery Precautions Note the following information which is specific to polymer batteries only, and where applicable, this overrides the general battery precaution information overleaf. • Polymer batteries may experience a slight expansion or swelling, however this is part of the battery’s safety mechanism and is not a cause for concern. • Use proper handling procedures when using polymer batteries.
Preface Battery Precautions • Only use batteries designed for this computer. The wrong battery type may explode, leak or damage the computer. • Do not remove any batteries from the computer while it is powered on. • Do not continue to use a battery that has been dropped, or that appears damaged (e.g. bent or twisted) in any way. Even if the computer continues to work with a damaged battery in place, it may cause circuit damage, which may possibly result in fire.
Preface Cleaning Do not apply cleaner directly to the computer; use a soft clean cloth. Do not use volatile (petroleum distillates) or abrasive cleaners on any part of the computer. Servicing Do not attempt to service the computer yourself. Doing so may violate your warranty and expose you and the computer to electric shock. Refer all servicing to authorized service personnel. Unplug the computer from the power supply.
Preface Travel Considerations Packing As you get ready for your trip, run through this list to make sure the system is ready to go: 1. 2. 3. 4. 5. 6. 7. 8. Check that the battery pack and any spares are fully charged. Power off the computer and peripherals. Close the display panel and make sure it’s latched. Disconnect the AC/DC adapter and cables. Stow them in the carrying bag. The AC/DC adapter uses voltages from 100 to 240 volts so you won’t need a second voltage adapter.
Preface On the Road In addition to the general safety and maintenance suggestions in this preface, and Chapter 8: Troubleshooting, keep these points in mind: Hand-carry the notebook - For security, don’t let it out of your sight. In some areas, computer theft is very common. Don’t check it with normal luggage. Baggage handlers may not be sufficiently careful. Avoid knocking the computer against hard objects.
Preface Developing Good Work Habits Developing good work habits is important if you need to work in front of the computer for long periods of time. Improper work habits can result in discomfort or serious injury from repetitive strain to your hands, wrists or other joints. The following are some tips to reduce the strain: • Adjust the height of the chair and/or desk so that the keyboard is at or slightly below the level of your elbow. Keep your forearms, wrists, and hands in a relaxed position.
Preface Lighting Proper lighting and comfortable display viewing angle can reduce eye strain and muscle fatigue in your neck and shoulders. • • • • Position the display to avoid glare or reflections from overhead lighting or outside sources of light. Keep the display screen clean and set the brightness and contrast to levels that allow you to see the screen clearly. Position the display directly in front of you at a comfortable viewing distance. Adjust the display-viewing angle to find the best position.
Preface Contents Notice .............................................................................................................................................................I ErP Off Mode Power Consumption Statement: ........................................................................................... II FCC Statement ............................................................................................................................................
Preface Models A & B: LCD Panel Open ..............................................................................................................1-7 Models C & D: LCD Panel Open ..............................................................................................................1-8 LED Indicators ...........................................................................................................................................1-9 Keyboard - Models A & B ....................................
Preface Power Options .........................................................................................................................................1-37 Shut Down, Restart or Sleep (Charms Bar) ............................................................................................ E-37 Running Apps ..........................................................................................................................................1-38 Features & Components Overview .....................
Preface Turning On the Computer ..........................................................................................................................3-3 Shutting the Computer Down ....................................................................................................................3-4 Power Plans ...............................................................................................................................................3-5 Power-Saving States ............................
Preface Driver Installation ......................................................................................................................................4-2 Updating/Reinstalling Individual Drivers ..................................................................................................4-5 User Account Control ................................................................................................................................4-6 Windows Security Message .........................
Preface Failing the POST .......................................................................................................................................5-3 Fatal Errors ................................................................................................................................................5-3 Non-Fatal Errors ........................................................................................................................................5-3 Setup Screens ................
Preface Boot Option Priorities (Boot Menu) ........................................................................................................5-14 UEFI Boot (Boot Menu) ..........................................................................................................................5-14 Exit Menu ................................................................................................................................................5-15 Upgrading The Computer Overview ...................
Preface Taking Pictures/Capturing Video ..............................................................................................................7-7 Camera Roll ...............................................................................................................................................7-8 Wireless LAN Module .............................................................................................................................7-12 3rd Party 802.11b/g/n Driver Installation .......
Preface 3G Configuration in Windows .................................................................................................................7-42 EM820W 3G Module PIN Code & Power-Saving ..................................................................................7-45 Troubleshooting Overview ....................................................................................................................................................8-1 Basic Hints and Tips ...............................
Preface Dynamic Video Memory Technology ......................................................................................................C-1 Microsoft Hybrid Graphics .......................................................................................................................C-2 Intel® HD Graphics Control Panel ...........................................................................................................C-4 Display Devices & Options ...............................................
Preface Card Reader ..............................................................................................................................................D-4 Slot ............................................................................................................................................................D-4 Communication .........................................................................................................................................D-4 Power Management .........
Preface XXVIII
Quick Start Guide Chapter 1: Quick Start Guide Overview This Quick Start Guide is a brief introduction to the basic features of your computer, to navigating around the computer and to getting your system started. The remainder of the manual covers the following: • Chapter 2 • Chapter 3 • Chapter 4 • Chapter 5 • Chapter 6 • Chapter 7 • Chapter 8 • Appendix A • Appendix B • Appendix C • Appendix D A guide to using some of the main features of the computer e.g.
1 Quick Start Guide Advanced Users If you are an advanced user you may skip over most of this Quick Start Guide. However you may find it useful to refer to “What to Install” on page 4 - 1, “BIOS Utilities” on page 5 - 1 and “Upgrading The Computer” on page 6 - 1 in the reminder of the User’s Manual. You may also find the notes marked with a of interest to you.
Quick Start Guide Not Included Operating Systems (e.g. Windows 8.1) and applications (e.g. word processing, spreadsheet and database programs) have their own manuals, so please consult the appropriate manuals. Drivers If you are installing new system software, or are re-configuring your computer for a different system, you will need to install the drivers listed in “Drivers & Utilities” on page 4 - 1. Drivers are programs which act as an interface between the computer and a hardware component e.g.
1 Quick Start Guide System Startup 1. 2. 3. 4. Remove all packing materials, and place the computer on a stable surface. Securely attach any peripherals you want to use with the notebook (e.g. keyboard and mouse) to their ports.
Quick Start Guide System Software Your computer may already come with system software pre-installed. Where this is not the case, or where you are re-configuring your computer for a different system, you will find the Windows 8.1 (64-bit) operating system is supported. Note: In order to run Windows without limitations or decreased performance, your computer requires a minimum 1GB of system memory (RAM). Windows OS In order to run Windows 8.
1 Quick Start Guide Model Differences This notebook series includes four different model types that mainly differ as indicated in the table below. Note that your model may appear slightly different from those pictured in this manual (see Appendix D for details).
Quick Start Guide Models A & B: LCD Panel Open 2 1 3 Figure 1 - 2 LCD Panel Open Wireless Device Operation Aboard Aircraft 4 5 6 7 8 The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the 3G/WLAN/Bluetooth module(s) are OFF if you are using the computer aboard aircraft.
1 Quick Start Guide Figure 1 - 3 LCD Panel Open 1. 2. 3. 4. 5. 6. 7. 8. Models C & D: LCD Panel Open Built-in PC Camera PC Camera LED Built-In Microphone LCD Power Button LED Status Indicators (Caps, Num & Scroll Lock) Keyboard Clickpad & Buttons 1 2 Wireless Device Operation Aboard Aircraft 4 6 Note that the clickpad has a defined valid operational area of sensitivity indicated within the sensor area of the illustration below. See “Touchpad Sensitivity” on page 2 - 7.
Quick Start Guide LED Indicators Icon The LED indicators on the computer display helpful information about the current status of the computer.
1 Quick Start Guide Other Keyboards If your keyboard is damaged or you just want to make a change, you can use any standard USB keyboard. The system will detect and enable it automatically. However special functions/hot-keys unique to the system’s regular keyboard may not work. Keyboard - Models A & B The keyboard has an embedded numerical keypad for easy numeric data input, and function keys to change operational features instantly.
Quick Start Guide Keyboard - Models C & D The keyboard has an embedded numerical keypad for easy numeric data input, and function keys to change operational features instantly. Function Keys Play/Pause Key NumLk & ScrLk Keys Numerical Keypad Fn Key Windows Logo Key Menu/Application Key Other Keyboards If your keyboard is damaged or you just want to make a change, you can use any standard USB keyboard. The system will detect and enable it automatically.
1 Quick Start Guide Windows Logo Keyboard Shortcut Use the Windows logo key + D key combination to switch from the Start screen to the Windows Desktop. Keyboard Shortcuts The following Windows Logo Key (Winkey) keyboard shortcuts are useful for navigation/operation in Windows.
Quick Start Guide Function/Hot Key Indicators Keys Function Keys Function The function keys (F1 - F12 etc.) will act as hot keys when pressed while the Fn key is held down. In addition to the basic function key combinations; visual indicators are available when the hot key utility is installed.
1 Quick Start Guide Control Center When in the Windows Desktop application (not in the Start screen) press the Fn + Esc key combination, or double-click the icon in the notification area of the taskbar to toggle the Control Center on/off. The Control Center gives quick access to frequently used controls and enables you to quickly turn the camera/Touch Pad on/off (see Appendix B for full details). Control Center Click on any button to turn any of the modules (e.g. TouchPad, Camera) on/off.
Quick Start Guide Models A & B: Front & Left Views Figure 1 - 7 Models A & B Front & Left Views 1 1. 2 2. 3 4 5 6 7 8 9 3. 4. 5. Multi-In-1 Card Reader 6. 7. The card reader allows you to use the most popular digital storage card formats: MMC (MultiMedia Card) / RS MMC SD (Secure Digital) / Mini SD / SDHC / SDXC MS (Memory Stick) / MS Pro / MS Duo 8. 9.
1 Quick Start Guide Figure 1 - 8 Models C & D Front & Left Views 1. 2. 3. 4. 5. 6. 7. 8. 9. LED Power Indicators Multi-in-1 Card Reader DC-In Jack Vent/Fan Intake/ Outlet External Monitor Port RJ-45 LAN Jack Combined eSATA/USB 3.0 Port HDMI-Out Port USB 3.
Quick Start Guide Models A & B: Right & Rear Views 1 2 3 Figure 1 - 9 Models A & B Right & Rear Views 5 4 6 7 Battery Information Always completely discharge, then fully charge, a new battery before using it. Completely discharge and charge the battery at least once every 30 days or after about 20 partial discharges. 1. Microphone-In Jack 2. Headphone-Out Jack 3. USB 2.0 Port 4. USB 3.0 Port 5. Optical Device Drive Bay (for CD/ DVD Device) 6. Security Lock Slot 7.
1 Quick Start Guide Figure 1 - 10 Models C & D Right & Rear Views 1. Microphone-In Jack 2. Headphone-Out Jack 3. USB 2.0 Port 4. USB 3.0 Port 5. Optical Device Drive Bay (for CD/ DVD Device) 6. Security Lock Slot 7. Battery Models C & D: Right & Rear Views 1 2 3 5 4 6 7 Battery Information Always completely discharge, then fully charge, a new battery before using it. Completely discharge and charge the battery at least once every 30 days or after about 20 partial discharges. USB 3.
Quick Start Guide Disk Eject Warning Changing DVD Regional Codes Don’t try to eject a CD/DVD while the system is accessing it. This may cause the system to “crash”. Stop the disk first then eject it, or press the stop button twice. Go to the Control Panel and double-click Device Manager (Hardware and Sound), then click the + next to DVD/CD-ROM drives.
1 Quick Start Guide Figure 1 - 11 Models A & B Bottom View 1. 2. 3. 4. 5. Models A & B: Bottom View 1 Battery Component Bay Cover Vent/Fan Intake/ Outlet Multi-in-1 Card Reader Speakers 3 2 3 5 5 CPU Overheating The CPU is not a user serviceable part. 4 To prevent your computer from overheating make sure nothing blocks the Vent/Fan Intake while the computer is in use.
Quick Start Guide Models C & D: Bottom View Figure 1 - 12 Models C & D Bottom View 1 1. 2. 3 3. 3 4. Battery Component Bay Cover Vent/Fan Intake/ Outlet Speakers 2 3 3 4 4 Overheating CPU To prevent your computer from overheating make sure nothing blocks the Vent/Fan Intake while the computer is in use. The CPU is not a user serviceable part.
1 Quick Start Guide Windows Versions Note that the information included on the following pages is for Windows 8.1 only. The Windows 8 interface is slightly different in appearance and in methods of navigation, and a separate manual is provided on the Device Drivers & Manual Disc with reference to Windows 8. Windows 8.1 Control Panel Throughout this manual you will see an instruction to open the Control Panel.
Quick Start Guide Right-click the Start button in the Desktop app (or use the Windows Logo Key + X key combination) to bring up an advanced context menu of useful features such as Control Panel, Programs and Features, Power Options, Task Manager, Search, File Explorer, Command Prompt, Device Manager and Network Connections etc.
1 Quick Start Guide The Control Panel can be accessed in a number of ways in Windows 8.1. • Click Search in the Windows Charms Bar (see previous page) and the search pane will pop out. Type Control Panel and select it from the results to the left. Figure 1 - 15 - Search (Control Panel) • Click on This PC (in Apps, or you can to pin This PC to the Start screen), click on Computer in the top menu and select Open Control Panel from the ribbon.
Quick Start Guide • When in the Desktop app (this does not apply to the Start screen) click on Settings in the Windows Charms Bar and select Control Panel from the menu. Figure 1 - 17 - Settings Charms Bar (Desktop App Only) • Click the arrow at the bottom of the Start screen and click Control Panel in Apps (Windows System). Figure 1 - 18 - All Apps - Control Panel Windows 8.
1 Quick Start Guide Right-click the Start button to bring up the menu and select Control Panel (see Figure 1 - 14 on page 1 - 23). Keyboard Shortcut to Control Panel You can also use keyboard shortcuts to access the Control Panel. Press the Windows logo key and X to bring up the context menu, and then press P to bring up the Control Panel. Alternatively press the Windows logo key and R to bring up the Run dialog box, and then type “Control Panel” and press Enter to access the Control Panel.
Quick Start Guide Windows 8.1 Start Screen & Desktop The Apps, control panels, utilities and programs within Windows are accessed from the Start screen and/or Windows Desktop app. The Desktop (which runs as an app within the Start screen) can be accessed by clicking the Desktop item in the Start screen (or by using the Windows Logo Key + D key combination). Click the arrow at the bottom of the Start screen to access Apps. Desktop App Figure 1 - 19 - Windows Start Screen Windows 8.
1 Quick Start Guide Apps & Tiles The Start screen will contain a number of apps, and many more will be installed as you add more applications etc. Not all of these apps can fit on one screen so you will often need use the slider at the bottom of the screen in order to view all the necessary Apps. Accessing Pining/Unpinning All Apps You can add and remove the tiles for apps and control panels in the Start screen. Right-click on a blank area of the Start screen, and you will see the Customize icon.
Quick Start Guide Desktop Application When the Desktop app is running (click the app in the Start screen or use the Windows Logo Key + D key combination) you can use lower left hot corner to switch between the Start screen and the Windows Desktop app. To do so move your mouse to hover over the bottom left corner of the Desktop app and left-click. When you move to the lower left hot corner in the Start screen it will take you back to your most recently used app (if one is running).
1 Quick Start Guide The Charms Bar The right side of the screen displays the Charms Bar. The Charms Bar contains the Search, Share, Start, Devices and Settings menus. To access up the Charms Bar move the cursor to the upper or lower right corners of the screen, and then hover over one of the items in the Charms Bar to activate it (the bar will be black when it is active), or use the Windows Logo Key + C key combination.
Quick Start Guide Charms Bar Items • Search results. • Share : You can search for any file, application, Apps and control panel settings with instantaneous : This button is used to share information with people via mail or social networks. • Start : Click to bring up the Start screen (the same function as pressing the Windows Logo Key or clicking the bottom left of the screen). • Devices : Click this button to change connected peripheral device settings e.g. an external display.
1 Quick Start Guide Windows 8.1 Taskbar In many instances throughout this manual you will see an instruction to access the notification area of the taskbar (system tray). In Windows 8.1 the taskbar is accessed from the Desktop application; if you are in the Start screen you will need to switch to the Desktop. The taskbar is displayed at the bottom of the Desktop screen, and you can see the notification area (system tray) of the taskbar in the bottom right of the screen.
Quick Start Guide Video Features You can switch display devices, and configure display options, from the Display control panel (in Appearances and Personalization) in Windows when running the Desktop app (see “Desktop Application” on page 1 - 29). It is possible to quickly configure external displays from the Devices menu item in the Charms Bar (see “The Charms Bar” on page 1 - 30). To Configure Displays from Devices (Charms Bar): 1. 2. 3. 4. Attach your display to the appropriate port, and turn it on.
1 Quick Start Guide To access Display (Control Panel) and Screen Resolution in Windows 8: 1. 2. 3. Go to the Control Panel. Click Display (icon) - In the Appearance and Personalization category. Adjust resolution. Right-Click Desktop App 1. 1 2 2. 3 3. Figure 1 - 26 - Screen Resolution 1 - 34 Video Features You can right-click the desktop and select Screen resolution 1 (Figure 1 26). Use the dropbox to select the screen Resolution 2 (Figure 1 - 26).
Quick Start Guide To access the Intel(R) HD Graphics Control Panel: 1. 2. Click Advanced settings 3 (Figure 1 - 26 on page 1 - 34) in the Screen Resolution control panel in Windows. Click the Intel(R)... tab and click Graphics Properties (button) 4 (Figure 1 - 27 on page 1 - 35) . OR 3. Right-click the desktop and select Graphics Properties from the menu. OR 4. Click the icon in the notification area of the Desktop taskbar and select Graphics Properties from the menu.
1 Quick Start Guide To access the NVIDIA Control Panel: 1. Right-click the desktop and select NVIDIA Control Panel 5 (Figure 1 - 28). OR 2. Double-click the icon 6 (Figure 1 - 28) in the Windows control panel.
Quick Start Guide Power Options Power Options (Hardware and Sound) can be accessed from the Control Panel. The Power Menu item in Settings in the Charms Bar in Windows 8.1 may be used to Shut down or Restart (you can also add Hibernate/ Sleep to the menu - see “Adding Hibernate/Sleep to the Power Menu” on page 3 - 10). You can also use the context menu (Shut down or sign out) shut the computer down/restart etc. Shut Down, Restart or Sleep (Charms Bar) 1. 2. 3. Go to the Charms Bar and click Settings.
1 Quick Start Guide Running Apps To run apps in Windows 8.1 you will need to check that the Screen Resolution and User Account Control Settings are compatible with the system requirements. Screen Resolution Settings 1. 2. Switch to the Windows Desktop (click the app or use the Windows logo key + D key combination). Right-click a blank area of the Windows Desktop and select Screen Resolution.
Quick Start Guide User Account Control Settings If your computer meets the minimum screen resolution requirements, and still you can't run apps, then that you have to check the status of User Account Control (UAC). Apps may fail to open when the UAC is turned off. To check whether the UAC is on or off, follow the instructions below. 1. 2. 3. 4. Open the Control Panel.
1 Quick Start Guide 1 - 40
Features & Components Chapter 2: Features & Components 2 Overview Read this chapter to learn more about the following main features and components of the computer: • • • • • Hard Disk Drive Optical (CD/DVD) Device Multi-In-1 Card Reader Touchpad/Clickpad and Buttons/Mouse Audio Features Overview 2 - 1
Features & Components 2 Power Safety Before attempting to access any of the internal components of your computer please ensure that the machine is not connected to the AC power, and that the machine is turned off. Also ensure that all peripheral cables, including phone lines, are disconnected from the computer. Hard Disk Drive The hard disk drive is used to store your data in the computer. The hard disk can be taken out to accommodate other 2.5" serial (SATA) hard disk drives with a height of 9.5 mm.
Features & Components Optical (CD/DVD) Device There is a bay for a 5.25" optical (CD/DVD) device (12.7mm height). The actual device will depend on the module you purchased (see “Storage” on page D - 3). The optical device is usually labeled “Drive D:” and may be used as a boot device if properly set in the BIOS (see “Boot Menu” on page 5 - 13).
Features & Components 2 Handling CDs or DVDs CD Emergency Eject If you need to manually eject a CD (e.g. due to an unexpected power interruption) you may push the end of a straightened paper clip into the emergency eject hole. However please do NOT use a sharpened pencil or similar object that may break and become lodged in the hole. Proper handling of your CDs/DVDs will prevent them from being damaged. Please follow the advice below to make sure that the data stored on your CDs/DVDs can be accessed.
Features & Components DVD Regional Codes To change the DVD regional codes: 1. 2. 3. Go to the Control Panel Double-click Device Manager (Hardware and Sound), then click the + next to DVD/CD-ROM drives. Double-click on the DVD-ROM device to bring up the Properties dialog box, and select the DVD Region (tab) to bring up the control panel to allow you to adjust the regional code.
Features & Components Multi-In-1 Card Reader 2 The card reader allows you to use some of the latest digital storage cards. Push the card into the slot and it will appear as a removable device, and can be accessed in the same way as your hard disk (s). Make sure you install the card reader driver (see “CardReader” on page 4 - 7.
Features & Components Touchpad/Clickpad and Buttons/Mouse The touchpad/clickpad is an alternative to the mouse; however, you can also add a mouse to your computer through one of the USB ports. The touchpad/clickpad buttons function in much the same way as a two-button mouse. Install the driver as instructed in “Touchpad” on page 4 - 8 and the appropriate application software version will be installed for your computer.
Features & Components 2 Mouse Driver If you are using an external mouse your operating system may be able to auto-configure your mouse during its installation or only enable its basic functions. Be sure to check the device’s user documentation for details.
Features & Components The Elan Smart-Pad control panel allows you to use a specific gesture (action) on the surface of the touchpad to perform specific actions to manipulate documents, objects and applications. 2 Click the menu tabs (One-finger, Multi-finger or Additional) and then the function button on the left to access the Configuration controls in the right panel. Click the check box to Enable most of the controls and click Apply to save the settings.
Features & Components Click the Function Description tion. 2 Click the Default button to get a detailed description of any func- button to set any of the functions to the default setting.
Features & Components One-Finger 2 Tapping One-Finger tapping is equivalent to clicking the left mouse button to perform a point/click/select function. Figure 2 - 8 Tapping Button The left and right touchpad buttons may be configured to perform any action listed in the Button drop-down menu.
Features & Components Drag and Drop You can select the different drag and drop methods from the menu provided. The object can be released when you lift the finger off the touchpad, when you tap again or after a set time delay. 2 Figure 2 - 10 Drag and Drop Edge Scroll Enable Vertical or Horizontal Scroll from this menu. You can configure the width of the scrollable area by adjusting the slider accordingly. To scroll vertically, tap the right edge of the touchpad and drag the finger up and down.
Features & Components Edge Swipe Enable Edge Swipe to use a single finger to scroll from the edges of the touchpad to perform the designated function in Windows 8.
Features & Components Multi-Finger 2 Zooming Place two fingers on the touchpad (for best results use the tips of the fingers) and slide them apart to zoom in, or closer together to zoom out. Figure 2 - 13 Zooming Scrolling The Two-Finger scrolling feature works in most scrollable windows and allows you to scroll horizontally and vertically. Tap the pad surface and slide both fingers in the direction required (vertically or horizontally as long as the option is selected).
Features & Components Rotation You can rotate objects by using a two-finger gesture. Touch and rotate using two fingers on the pad in the direction required. Alternatively place a finger down on the pad and rotate the other finger around it in a circular motion (clockwise or counterclockwise). 2 Figure 2 - 15 Rotation Three Finger Swipe This gesture is used to activate a Page Up/Page Down operation.
Features & Components Additional 2 Palm Tracking This feature helps guard against accidental contact such as palms resting on the pad. Use the slider to adjust the sensitivity of the feature as appropriate. Figure 2 - 17 Palm Tracking Sensitivity Adjust the level of finger pressure required for the cursor to respond from this menu.
Features & Components Audio Features You can configure the audio options on your computer from the Sound control panel in Windows, from the HD VDeck icon on the desktop or VIA HD Audio Deck control panel . The volume may also be adjusted by means of the Fn + F5/F6 key combination. Sound Volume Adjustment The sound volume level is set using the volume control on the Windows desktop (and the volume function keys F5/ F6 on the computer). Click the volume icon in the taskbar to check the setting.
Features & Components 2 Expert Mode will allow you to access more advanced configuration menus for Speaker and Microphone. Syncing Left & Right Volume Balance If you wish to adjust the left and right channel volume levels separately, you will need to adjust this from the VIA HD Audio Deck in Expert Mode. Click Speaker in VIA HD Audio Deck (in Expert Mode) and click the Sync Left and Right volume button (see left).
Power Management Chapter 3: Power Management Overview To conserve power, especially when using the battery, your computer power management conserves power by controlling individual components of the computer (the monitor and hard disk drive) or the whole system.
Power Management 3 Forced Off If the system “hangs”, and the Ctrl + Alt + Del key combination doesn’t work, press the power button for 4 seconds, or longer, to force the system to turn itself off. The Power Sources The computer can be powered by either an AC/DC adapter or a battery pack. AC/DC Adapter Use only the AC/DC adapter that comes with your computer. The wrong type of AC/ DC adapter will damage the computer and its components. 1. 2. 3.
Power Management Turning On the Computer Now you are ready to begin using your computer. To turn it on simply press the power button on the front panel. When the computer is on, you can use the power button as a Stand by/Hibernate/ Shutdown hot-key button when it is pressed for less than 4 seconds (pressing and holding the power button for longer than this will shut the computer down). Use Power Options (Hardware and Sound) in the Windows control panel to configure this feature.
Power Management Shutting the Computer Down Note that you should always shut your computer down by choosing the Shut down command as this will help prevent hard disk or system problems. Use the Shut down or sign out item in the Context Menu (right-click the lower left corner of the screen to bring up the menu). 3 You can also use the Power Menu in Settings in the Windows 8.1 Charms Bar. If you want to add Hibernate/Sleep to the Power Menu see “Adding Hibernate/Sleep to the Power Menu” on page 3 - 10.
Power Management Power Plans The computer can be configured to conserve power by means of power plans. You can use (or modify) an existing power plan, or create a new one. The settings may be adjusted to set the display to turn off after a specified time, and to send the computer into Sleep after a period of inactivity. Click Change plan settings and then click Change advanced power settings to access further configuration options in Advanced Settings.
Power Management Each Windows power plan will also adjust the processor performance of your machine in order to save power. This is worth bearing in mind if you are experiencing any reduced performance (especially under DC/battery power). 3 Choose High performance (you may need to click Show additional plans to view the High performance plan) for maximum performance when the computer is powered from an AC power source.
Power Management Power-Saving States You can use power-saving states to stop the computer’s operation and restart where you left off. Win 8.1 uses the Sleep, Hibernate and Shut Down power-saving states. Sleep In Sleep all of your work, settings and preferences are saved to memory before the system sleeps. When you are not using your computer for a certain length of time, which you specify in the operating system, it will enter Sleep to save power.
Power Management Hibernate Hibernate uses the least amount of power of all the power-saving states and saves all of your information on a part of the hard disk before it turns the system off. If a power failure occurs the system can restore your work from the hard disk; if a power failure occurs when work is saved only to memory, then the work will be lost. Hibernate will also return you to where you last left off within seconds.
Power Management Configuring the Power Buttons The power/sleep button (Fn + F4 key combo) and closed lid may be set to send the computer in to a power-saving state. Click Choose what the power buttons do on the left menu in Power Options to bring up the menu. Password Protection It is recommended that you enable a password on wake up in order to protect your data.
Power Management Adding Hibernate/Sleep to the Power Menu Add Hibernate/Sleep to the Power Menu as follows. 1. 2. 3. 4. 5. 3 Go to the Power Options (Hardware and Sound) control panel. Click “Change settings that are currently unavailable” Click Choose what the power buttons do. Click to put a check in the Hibernate/Sleep box under Shutdown settings. Click Save Changes and close the control panel. Figure 3 - 6 Power Options Define Power Buttons - Shutdown Settings 3 - 10 Configuring the Power Buttons .
Power Management Resuming Operation You can resume operation from power-saving states by pressing the power button, or in some cases pressing the sleep button (Fn + F4 key combo).
Power Management 3 Power Conservation Modes The Energy Star setting will result in maximum power saving, but with the possible loss of some performance. Power Conservation Modes This system supports Energy Star power management features that place computers (CPU, hard drive, etc.) into a low-power sleep modes after a designated period of inactivity. Adjust Power Conservation Modes from the Control Center: 1. 2. 3. Press the Fn + Esc key combination to toggle the Control Center on/off.
Power Management Ctrl + Alt + Delete Key Combination You can use the CTRL + ALT + DEL key combination from almost any of the Windows 8 interfaces/Apps to bring up a full-screen displaying Lock, Switch User, Log off, Change a password and Task Manager options. If you click the Power icon in the lower right corner of the screen a power management option menu appears to display Sleep, Shut down, and Restart.
Power Management 3 Low Battery Warning When the battery is critically low, immediately connect the AC/DC adapter to the computer or save your work, otherwise, the unsaved data will be lost when the power is depleted. Battery Information Follow these simple guidelines to get the best use out of your battery. Battery Power Your computer’s battery power is dependent upon many factors, including the programs you are running, and peripheral devices attached. You can set actions to be taken (e.g.
Power Management Conserving Battery Power • Use a power plan that conserves power (e.g Power saver), however note that this may have an affect on computer performance. • Lower the brightness level of the LCD display. The system will decrease LCD brightness slightly to save power when it is not powered by the AC/DC adapter. • Reduce the amount of time before the display is turned off. • Close wireless, Bluetooth, modem or communication applications when they are not being used (e.g.
Power Management Battery Life 3 Battery life may be shortened through improper maintenance. To optimize the life and improve its performance, fully discharge and recharge the battery at least once every 30 days. We recommend that you do not remove the battery yourself as removing the bottom cover may void your warranty. New Battery Always completely discharge, then fully charge, a new battery (see “Battery FAQ” on page 3 - 18 for instructions on how to do this).
Power Management Proper handling of the Battery Pack • DO NOT disassemble the battery pack under any circumstances • DO NOT expose the battery to fire or high temperatures, it may explode • DO NOT connect the metal terminals (+, -) to each other Caution Danger of explosion if battery is incorrectly replaced. Damaged Battery Warning Should you notice any physical defects (e.g.
Power Management Battery FAQ How do I completely discharge the battery? Use the computer with battery power until it shuts down due to a low battery. Don’t turn off the computer even if a message indicates the battery is critically low, just let the computer use up all of the battery power and shut down on its own. 3 1. 2. Save and close all files and applications. Create a power plan for discharging the battery and set all the options to Never.
Power Management 3. Click Change plan settings (after creating it) and click Change plan settings > Change advanced power settings.
Power Management 4. 5. Scroll down to Battery and click + to expand the battery options.
Power Management How do I fully charge the battery? When charging the battery, don’t stop until the LED charging indicator light changes from orange to green. How do I maintain the battery? Completely discharge and charge the battery at least once every 30 days or after about 20 partial discharges.
Power Management 3 3 - 22
Drivers & Utilities Chapter 4: Drivers & Utilities This chapter deals with installing the drivers and utilities essential to the operation or improvement of some of the computer’s subsystems. The system takes advantage of some newer hardware components for which the latest versions of most available operating systems haven’t built in drivers and utilities. Thus, some of the system components won’t be auto-configured with an appropriate driver or utility during operating system installation.
Drivers & Utilities Driver Installation 4 1. 2. 3. 4. 5. 6. Insert the Device Drivers & Utilities + User’s Manual disc into the computer’s DVD drive. Click the message “Tap to choose what happens with this disc.” Click Run autorun.exe. Click Install Drivers (button), or Option Drivers (button) to access the Optional driver menu.
Drivers & Utilities 7. Follow the instructions for each individual driver installation procedure as listed on the following pages. For Models A & B (No Cardreader Patch driver) For Models C & D (Cardreader Patch driver included) 4 Figure 4 - 2 - Install Drivers All drivers provided are for the Windows 8.1 operating system. Note that you need to install both the WLAN & Bluetooth drivers for Intel and 3rd party WLAN & Bluetooth Combo modules.
Drivers & Utilities Win 8.1 Driver 4 Page # Win 8.1 Optional Items Page # Chipset Page 4 - 7 PC Camera Module (No driver required for Windows 8.
Drivers & Utilities Manual Driver Installation Click Browse CD/DVD (button) in the Drivers Installer application and browse to the executable file in the appropriate driver folder. Windows Update After installing all the drivers make sure you enable Windows Update in order to get all the latest security updates etc. (all updates will include the latest hotfixes from Microsoft). See “Windows Update” on page 4 9 for instructions.
Drivers & Utilities User Account Control 4 If a User Account Control prompt appears as part of the driver installation procedure, click Continue or Allow, and follow the installation procedure as directed. Windows Security Message If you receive a Windows security message as part of the driver installation process. Just click “Install this driver software anyway” or “Install” to continue the installation procedure.
Drivers & Utilities Driver Installation Procedure Insert the Device Drivers & Utilities + User’s Manual disc and click Install Drivers (button). Note: After installing the video driver go to the Display control panel to adjust the video settings to the highest resolution. Chipset 1. Click 1.Install Chipset Driver > Yes. 2. Click Next > Yes > Next > Next. 3. Click Finish to restart the computer. LAN 1. Click 4.Install LAN Driver > Yes. 2. Click Next > Install. 3. Click Finish. Video (VGA) 1. Click 2.
Drivers & Utilities 4 Touchpad 1. Click 6./7.Install Touchpad Driver > Yes. 2. Click Next. 3. Click the button to accept the license agreement and click Next. 4. Click Finish > Restart Now to restart the computer. Hot Key 1. Click 7./8.Install Hotkey AP > Yes. 2. Click Next > Next. 3. Click Finish > Finish to restart the computer. Airplane Note: Do not use Update Driver in Device Manager to install the Airplane Mode driver. 1. Click 8./9.Install Airplane Mode AP > Yes. 2. Click Next. 3.
Drivers & Utilities It is recommended you now also install the Intel Rapid Storage Technology driver (see “Intel® Rapid Storage Technology” on page 7 - 22 - required for AHCI mode hard disks). Windows Update After installing all the drivers make sure you enable Windows Update in order to get all the latest security updates etc. (all updates will include the latest hotfixes from Microsoft). To enable Windows Update make sure you are connected to the internet: 1. 2. 3. 4. 5. 6. Go to the Control Panel.
Drivers & Utilities Optional Drivers See the pages indicated in Table 4 - 1, on page 4 - 4 for the driver installation procedures for any modules included in your purchase option. 4 Figure 4 - 3 - Option Drivers Note that you need to install both the WLAN & Bluetooth drivers for Intel and 3rd party WLAN & Bluetooth Combo modules.
BIOS Utilities Chapter 5: BIOS Utilities Overview This chapter gives a brief introduction to the computer’s built-in software: If your computer has never been set up, or you are making important changes to the system (e.g. hard disk setup), then you should review this chapter first and note the original settings found in Setup. Even if you are a beginner, keep a record of the settings you find and any changes you make. This information could be useful if your system ever needs servicing.
BIOS Utilities BIOS Settings Warning 5 Incorrect settings can cause your system to malfunction. To correct mistakes, return to Setup and restore the Optimized Defaults with . UEFI Boot & POST When UEFI Boot is enabled, then the prompts to press F2 or F7 will not appear. However you can still press F2 to enter the setup, or F7 to choose the preferred boot device, if you press the key immediately the system boots up.
BIOS Utilities Failing the POST Errors can be detected during the POST. There are two categories, “fatal” and “nonfatal”. Fatal Errors These stop the boot process and usually indicate there is something seriously wrong with your system. Take the computer to your service representative or authorized distributor/supplier as soon as possible. Non-Fatal Errors This kind of error still allows you to boot.
BIOS Utilities Setup Menus 5 The Setup menus shown in this section are for reference only. Your computer’s menus will indicate the configuration appropriate for your model and options. Setup Screens The following pages contain additional advice on portions of the Setup. Along the top of the screen is a menu bar with menu headings. When you select a heading, a new screen appears. Scroll through the features listed on each screen to make changes to Setup.
BIOS Utilities Main Menu Figure 5 - 2 Main Menu System Time & Date (Main Menu) The hour setting uses the 24-hour system (i.e., ØØ = midnight; 13 = 1 pm). If you can change the date and time settings in your operating system, you will also change these settings. Some applications may also alter data files to reflect these changes.
BIOS Utilities SATA Port # (Main Menu) Pressing Enter opens the sub-menu to show the configuration of a optical Device/ HDD on the computer’s SATA Ports. CPU/System/Extended Memory: (Main Menu) This item contains information on the CPU type and system memory, and is not user configurable. The system will auto detect the amount of memory installed. 5 MB Series / BIOS Revision / KBC/EC firmware Revision This item contains information on the BIOS version etc., and is not user configurable.
BIOS Utilities Advanced Menu Figure 5 - 3 Advanced Menu 5 Intel(R) Rapid Start Technology (Advanced Menu) Enable/disable Intel(R) Rapid Start Technology from this menu. The rapid start hibernation mode can resume power within 5 to 6 seconds and can remember your computer's state with zero power.
BIOS Utilities Intel Anti-Theft Technology (Advanced Menu) Anti-Theft Technology, which is built-in to the processor of the computer, allows system administrators to render your computer useless to thieves by sending a poison pillencrypted SMS message over a 3G network etc. Administrators can also remotely unlock a recovered computer quickly, or direct the system to send location information (GPS coordinates) back to a central server.
BIOS Utilities Power On Boot Beep (Advanced Menu) Use this menu item to enable/disable the beep as the computer starts up. Battery Low Alarm Beep (Advanced Menu) Use this menu item to enable/disable the battery low alarm beep.
BIOS Utilities Security Menu Security Menu 5 The changes you make here affect the access to the Setup utility itself, and also access to your machine as it boots up after you turn it on. These settings do not affect your machine or network passwords which will be set in your software OS. Figure 5 - 4 Security Menu Set Supervisor Password (Security Menu) You can set a password for access to the Aptio Setup Utility. This will not affect access to the computer OS (only the Aptio Setup Utility).
BIOS Utilities Note: To clear existing passwords press Enter and type the existing password, then press Enter for the new password (without typing any password entry) and Enter again to confirm the password clearance. Set User Password (Security Menu) You can set a password for user mode access to the Aptio Setup Utility. This will not affect access to the computer OS, (only the Setup utility) unless you choose to set a Password on Boot (see below).
BIOS Utilities Secure Boot Control (Security Menu) Secure Boot prevents unauthorized operating systems and software from loading during the startup process. Secure Boot Control is available as a menu option if you have enabled UEFI Boot (see “Boot Menu” on page 5 - 13). Enabling Secure Boot will bring up the Secure Boot Mode menu to enable you to configure Secure Boot as Standard (with a fixed secure boot policy), or Custom (which enables you to make changes to the Key Management database).
BIOS Utilities Boot Menu Figure 5 - 5 Boot Menu BIOS Screens Note that the BIOS screens pictured on these pages are intended for guidance in setting up your system’s BIOS. When you turn the computer on it will look for an operating system (e.g. Windows 7) from the devices listed in this menu, and in this priority order. If it cannot find the operating system on that device, it will try to load it from the next device in the order specified in the Boot Option Priorities.
BIOS Utilities Boot Option Priorities (Boot Menu) Use the arrow keys to move up and down the menu, and press Enter to select a device from the Boot Option # list. You can go to either Hard Drive BBS Priorities or Network Device BBS Priorities and use the + and - keys to move the device’s boot priority up and down the list (the selected device will be highlighted in white). UEFI Boot (Boot Menu) Enable/disable UEFI Boot from this menu.
BIOS Utilities Exit Menu Figure 5 - 6 Exit Menu 5 Click Save Changes and Reset to save all changes made. Choosing to Discard Changes, or Exit Discarding Changes, will wipe out any changes you have made to the Setup. You can also choose to restore the original Setup defaults that will return the Setup to its original state, and erase any previous changes you have made in a previous session.
BIOS Utilities 5 5 - 16
Upgrading The Computer Chapter 6: Upgrading The Computer Overview This chapter contains information on upgrading the computer. Follow the steps outlined to make the desired upgrades. If you have any trouble or problems you can contact your service representative for further help.
Upgrading The Computer When Not to Upgrade Power Safety Warning 6 Before you undertake any upgrade procedures, make sure that you have turned off the power, and disconnected all peripherals and cables (including telephone lines). It is advisable to also remove your battery in order to prevent accidentally turning the machine on. These procedures involve opening the system’s case, adding and sometimes replacing parts.
Upgrading The Computer Removing the Battery If you are confident in undertaking upgrade procedures yourself, for safety reasons it is best to remove the battery. 1. 2. 3. 4. Turn the computer off, and turn it over. Slide the latch 1 in the direction of the arrow. Slide the latch 2 in the direction of the arrow, and hold it in place. Slide the battery out in the direction of the arrow 3 .
Upgrading The Computer Removing the Component Bay Cover - Model A 1. 2. 3. 4. Turn off the computer, and turn it over and remove the battery (see page 6 - 3). Remove screws 1 & 2 from the bottom of the computer. Slide the component bay cover until the cover and case indicators 3 are aligned. Lift the bottom cover 4 off the computer case.
Upgrading The Computer Removing the Component Bay Cover - Model B 1. 2. 3. 4. Turn off the computer, and turn it over and remove the battery (see page 6 - 3). Remove screws 1 & 2 from the bottom of the computer. Lift the component bay cover off the computer case by applying pressure at points 3 & 4 ; if you have problems using a finger to do this, then use a non-abrasive, non-sharp object (e.g. a coin) to lift the cover up before removal). Remove the component bay cover 5 .
Upgrading The Computer Replacing the Component Bay Cover - Model A 1. 2. 3. Reinsert the component bay cover by placing it on the bottom case assembly, applying downward pressure and by sliding it on to the case in the direction of arrow 1 . Make sure the case markers 2 line up. Replace screws 1 - 3 (Figure 6 - 2 on page 6 - 4) and battery (see page 6 - 3).
Upgrading The Computer Replacing the Component Bay Cover - Model B 1. 2. 3. Reinsert the component bay cover by placing it on the bottom case assembly, and aligning the pins at the bottom of the cover with the slots in the case to ensure a proper fit. Press down on the cover to make sure it fits tightly. Replace screws 1 & 2 (Figure 6 - 2 on page 6 - 4) and battery (see page 6 - 3).
Upgrading The Computer HDD System Warning 6 New HDD’s are blank. Before you begin make sure: You have backed up any data you want to keep from your old HDD. You have all the discs required to install your operating system and programs. If you have access to the internet, download the latest application and hardware driver updates for the operating system you plan to install. Copy these to a removable medium. Upgrading the Hard Disk Drive The hard disk drive can be taken out to accommodate other 2.
Upgrading The Computer Removing the Hard Disk Drive Note that only a single Model is pictured, however the procedure is the same for both models. 1. 2. 3. Turn off the computer, and turn it over and remove the battery (see page 6 - 3) and component bay cover (see page 6 - 4/6 - 5). Lift the HDD sponge up at point 1 , grip the tab 2 , and slide the HDD assembly in the direction of arrow 3 . Remove the HDD assembly 4 .
Upgrading The Computer 4. 5. 6. 7. Remove screws 5 & 6 and the cover 7 . Reverse the process to install a new hard disk drive. Replace the HDD assembly by sliding it in the direction of arrow 8 , and press down on the sponge 9 to fit the assembly tightly. Replace the component bay cover and screws.
Upgrading The Computer Removing the Solid State Drive 1. 2. 3. 4. 5. 6. Turn off the computer, and turn it over and remove the battery (see page 6 - 3) and component bay cover (see page 6 - 4/6 - 5). The SSD slot is at point 1 on the mainboard. Remove screw 2 , and the SSD 3 will pop-up and you can then remove it. Replace the SSD by angling it as illustrated, and then fit the connector firmly into the slot. The SSD module’s pin alignment will allow it to only fit one way.
Upgrading The Computer Upgrading the Optical (CD/DVD) Device 1. 2. 3. 6 Figure 6 - 9 Removing the Optical Device Turn off the computer, and turn it over and remove the battery (see page 6 - 3) and component bay cover (see page 6 - 4/6 - 5). Remove the screw at point 1 , and use a screwdriver to carefully push out the optical device at point 2 . Reverse the process to install the new device.
Upgrading The Computer Upgrading the System Memory (RAM) The computer has two memory sockets for 204 pin Small Outline Dual In-line (SODIMM) DDR3L type memory modules (see “Memory” on page D - 2 for details of supported module types). 1. 2. Turn off the computer, and turn it over and remove the battery (see page 6 - 3) and component bay cover (see page 6 - 4/6 - 5). The memory sockets will be visible at point 1 .
Upgrading The Computer 3. Gently pull the two release latches on the sides of the memory socket in the direction indicated by the arrows ( 2 & 3 ) in Figure 6 - 11. Figure 6 - 11 RAM Module Release Latches 2 6 3 Contact Warning Be careful not to touch the metal pins on the module’s connecting edge. Even the cleanest hands have oils which can attract particles, and degrade the module’s performance. Figure 6 - 12 RAM Module Removal 4. The RAM module will 4 pop-up, and you can remove it.
Upgrading The Computer 5. 6. 7. 8. 9. Pull the latches to release the second module if necessary. Insert a new module holding it at about a 30° angle and fit the connectors firmly into the memory slot. The module’s pin alignment will allow it to only fit one way. Make sure the module is seated as far into the slot as it will go. DO NOT FORCE the module; it should fit without much pressure. Press the module in and down towards the mainboard until the slot levers click into place to secure the module.
Upgrading The Computer 6 6 - 16
Modules & Options Chapter 7: Modules & Options Overview This chapter contains information on the following modules, which may come with your computer, depending on the configuration purchased. If you are unsure please contact your service representative.
Modules & Options Important Notice If your purchase option includes both Wireless LAN and 3G modules, then the appropriate antennas will be installed. Note that In order to comply with FCC RF exposure compliance requirements, the antenna must not be co-located or operate in conjunction with any other antenna or transmitter.
Modules & Options PC Camera Module When the PC Camera application is run the LED indicator to the left of the camera will be illuminated in red (see 2 Figure 1 - 3 on page 1 - 8). Note that you need to use the Camera app in Windows to take pictures and capture video. Use the Fn + F10 key combination (see “Function/Hot Key Indicators” on page 1 - 13) to toggle power to the PC Camera module.
Modules & Options PC Camera Audio Setup If you want to capture video & audio with your camera, it is necessary to setup the audio recording options in Windows. 1. 2. 3. 4. 5. 6. 7 Go to the Control Panel. Click Sound (Hardware and Sound) and click Recording (tab). Right-click hold and release Microphone (Realtek High Definition Audio) and make sure the item is not disabled. Double-click Microphone (or select Properties from the right-click menu).
Modules & Options Camera App 1. 2. Run the Camera app from the Start screen by clicking on the Camera app icon . The camera interface will display two buttons on the right side of the screen. Figure 7 - 2 Camera App Buttons Exposure Use the slider to adjust the Exposure level. 3. 4. 5. The upper button is used to record video, and the lower button is used to take still pictures. Right-click on the screen to bring up menu buttons at the bottom of the screen.
Modules & Options Camera Options The Camera Options settings may be accessed as follows: 1. 2. 3. 4. 7 Figure 7 - 4 Camera Options 7 - 6 PC Camera Module Run the Camera app from the Start screen by clicking on the Camera app icon . While the camera app is running access the Charms Bar (e.g. click Use the Windows logo key + C key combination). Click Settings and then click Options.
Modules & Options Taking Pictures/Capturing Video 1. 2. 3. 4. 5. Run the Camera app from the Start screen by clicking on the Camera app icon . Right-click the screen and select the timer if you require a countdown before capture. Click the appropriate icon to take a picture or start video capture (if video capture begins a timer will appear in the bottom corner of the screen). To stop video capture click the main window again (or click the stop icon ).
Modules & Options Camera Roll 1. 2. 3. 4. Run the Camera app from the Start screen by clicking on the Camera app icon . Right-click on the screen to bring up menu buttons at the bottom of the screen. Click Camera Roll. Click the arrows / (on either side of the screen) to browse through the captured photos/video, and back to the Camera app. Editing Photos Figure 7 - 6 1. Clicking on a captured photo will bring up an app bar with a series of buttons. 2. 3.
Modules & Options photo with the edited changes), Update original (which changes the original picture permanently) or Undo any changes. 9. Click the Edit button to bring up a full suite of tools to edit the photo. 10. Click on the menu headings on the left, and then click on the tool on the right to edit the photo as required. Edit Menu Basic Fixes Light Color Effects Figure 7 - 7 Editing Tools 7 11.
Modules & Options Editing Photos 1. Clicking on a captured video will bring up an app bar with a series of buttons. 2. Click Delete to remove any video from the camera roll (you will be asked to click Delete again to confirm the deletion). The Open With button will allow you to select a program with which to run the Video. Clicking Slide Show will create a slide show of photos/video in the camera roll. Click Trim to edit the video.
Modules & Options Video File Size Note that capturing high resolution video files requires a substantial amount of disk space for each file. After recording video, check the video file size (right-click the file and select Properties) and the remaining free space on your hard disk (go to My Computer, right-click the hard disk, and select Properties). If necessary you can remove the recorded video file to a removable medium e.g. CD, DVD or USB Flash drive. Note that the Windows 8.
Modules & Options Wireless Device Operation Aboard Aircraft 7 The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the WLAN, Bluetooth & 3G module(s) are OFF if you are using the computer aboard aircraft by putting the system in to Airplane Mode (see Table 1 - 4, on page 1 12). Wireless LAN Module If you have included an Intel® or 3rd Party WLAN module in your purchase option make sure that the module is on (i.e.
Modules & Options 3rd Party 802.11b/g/n Driver Installation 1. Make sure the system is not in Airplane Mode, and then insert the Device Drivers & Utilities + User’s Manual disc into the DVD drive. 2. Click Option Drivers (button). 3. Click 1.Install WLAN Driver > Yes. 4. Click Next. 5. Click Finish to restart the computer. 6. The operating system is the default setting for Wireless LAN control in Windows (see page 7 - 14). Intel® WLAN Driver Installation 1.
Modules & Options WLAN Configuration in Windows You can configure a wireless connection using one of the following options, however make sure the Wireless LAN module is turned on (and not in Airplane Mode) before configuration begins. Charms Bar 1. 2. 3. Go to the Charms Bar. Select Settings and then click the WiFi icon (it should read Available under the icon and Airplane mode should be Off). A list of available access points will appear.
Modules & Options 4. 5. 6. 7. 8. Double-click an access point to connect to it (or click it and click Connect). Enter a network security key (password) if required, and click Next. You can choose to find other devices or not. When you are connected to the network access point it will display Connected . Select any connected network and click Disconnect to disconnect from a connected access point. 7 Figure 7 - 11 Networks Connected / Disconnect 9.
Modules & Options Desktop Mode 1. 2. 3. 4. 5. 6. 7. Switch to the Windows Desktop (click the app or use the Windows logo key D key combination). Click the wireless icon in the notification area of the taskbar. A list of available access points will appear. Double-click an access point to connect to it (or click it and click Connect). Enter a network security key (password) if required, and click Next. You can choose to find other devices or not.
Modules & Options Bluetooth & WLAN Combo Module If your purchase option includes the Combination Wireless LAN & Bluetooth module (either Intel® or 3rd Party) then install the driver as instructed overleaf. Make sure that the module is on (i.e. the system is not in Airplane Mode) before installing the driver. Bluetooth Data Transfer Note that the transfer of data between the computer and a Bluetooth enabled device is supported in one direction only (simultaneous data transfer is not supported).
Modules & Options High Speed Bluetooth Data Transfer 7 The Combination Wireless LAN & Bluetooth module supports high speed data transfer. However to achieve such transfer speeds, both devices must support high speed data transfer. To obtain high speed data transfer make sure that both the WLAN and Bluetooth modules are powered on. Check your Bluetooth compatible device’s documentation to confirm it supports high speed data transfer. 3rd Party Bluetooth (V4.0) Combo Driver Installation 1.
Modules & Options Bluetooth Configuration in Windows You can configure a Bluetooth connection as below, however make sure the Bluetooth module is on (or the system is not in Airplane Mode) before configuration. Desktop Mode 1. 2. 3. Switch to the Windows Desktop (click the App or use the Windows logo key D key combination). Click the notification area of the taskbar and double-click the Bluetooth icon click and select Show Bluetooth Devices). The Bluetooth item in PC and Devices will appear.
Modules & Options 4. 5. Make sure that Bluetooth is turned on and a list of discovered devices will appear. Double-click the device you want to pair with the computer and click Pair. 6. On first connection the computer will provide you with a pairing code to be entered onto the device. 7. Enter the code into your Bluetooth enabled device and click Yes on the computer to complete the pairing. Select a device and click Remove Device to disconnect from any device.
Modules & Options To Make your Computer Discoverable to Bluetooth Devices 1. 2. 3. 4. Switch to the Windows Desktop (click the app or use the Windows logo key + D key combination). Click the notification area of the taskbar, click the Bluetooth icon and click Open Settings. Click Options, and make sure that Allow Bluetooth devices to find this computer check box (Discovery) has a check inside it.
Modules & Options Intel® Rapid Storage Technology Install the Intel Rapid Storage Technology to support your SATA drive if set up in AHCI mode in the BIOS (see “SATA Mode (Advanced Menu)” on page 5 - 8), or if you have set up your hard disks / solid state drives in a RAID configuration for Intel® Smart Response Technology (see overleaf). 7 IRST Driver Installation 1. Insert the Device Drivers & Utilities + User’s Manual disc into the DVD drive. 2. Click Option Drivers (button). 3. Click 3.
Modules & Options Intel® Rapid Start Technology Driver Intel(R) Rapid Start Technology can resume power from Hibernation within 5 to 6 seconds and can remember your computer's previous state with zero power. System Requirements to support Intel® Rapid Start Technology: • Rapid Start Technology should be enabled in the BIOS (see ““Intel(R) Rapid Start Technology (Advanced Menu)” on page 5 - 7). • Intel Rapid Storage Technology software installed. • A Solid State Drive (SSD) with a minimum capacity of 18.
Modules & Options Intel® Rapid Start Technology Configuration 1. 2. 3. 7 Enable/disable Intel(R) Rapid Start Technology from the BIOS (see “Intel(R) Rapid Start Technology (Advanced Menu)” on page 5 - 7). Go the Windows control panel and double-click Administrative Tools (System and Security)> Computer Management > Storage > Disk Management Right-click the SSD and select Shrink Volume from the menu.
Modules & Options 4. Enter the figure, which should be equal to amount of system memory (RAM) in your computer, in “Enter the amount of space to shrink in MB”. Figure 7 - 18 Shrink Volume Size 7 5. Click Shrink (any unallocated file space may be formatted for storage use). Memory Size (Amount of Space to Shrink) The figure entered in the “Enter the amount of space to shrink in MB” field above should be equal to the amount of system memory in your computer.
Modules & Options 6. Run the Desktop app and right-click the lower left hot corner (or use the Windows Logo Key + X key combination) and select Command Prompt (Admin). 7. 8. Type “DISKPART”. At the DISKPART command type “list disk”.
Modules & Options 9. Type “select disk #” (# is disk number where you want to create the store partition, so refer to the results obtained from "list disk" for exact disk number). 10. The message “Disk # is now the selected disk.” will appear. Figure 7 - 21 Diskpart - Select Disk # 7 11. Type “create partition primary”. 12. A “DiskPart succeeded in creating the specified partition.” message should appear.
Modules & Options 13. Type “detail disk”. Figure 7 - 23 Diskpart - Detail Disk 14. Type “select Volume #” (# is volume of your storage partition so refer to results obtained from "detail disk" for the exact volume number). 15. The message “Volume # is now the selected volume.” will appear.
Modules & Options 16. Type the following, depending on the format of the SSD. • For MBR formatted SSDs: “set id=84 override” (the id must be set to 84). • For GPT formatted SSDs: “set id=D3BFE2DE-3DAF-11DF-BA40-E3A556D89593”. Figure 7 - 25 Diskpart - Set id= 7 17. The message “DiskPart successfully set the partition ID.” will appear. 18. Close the CMD window.
Modules & Options 19. Go the Windows control panel and double-click Administrative Tools (System and Security)> Computer Management > Storage > Disk Management. 20. The disk partition should read Healthy Hibernation Partition. Figure 7 - 26 Computer Management (Healthy Hibernation Partition) 7 Healthy (Hibernation Partition) 21. Restart the computer. 22. Install the driver (see below). Intel® Rapid Start Technology Driver Installation 1.
Modules & Options Sound Blaster Cinema EQ Install the Sound Blaster Cinema EQ to allow you to configure the audio settings to your requirements for the best performance in games, music and movies. Sound Blaster Cinema EQ Installation 1. Insert the Device Drivers & Utilities + User’s Manual disc into the CD/ DVD drive. 2. Click Option Drivers (button). 3. Click 5.Install SB Cinema EQ > Yes. 4. Choose the language you prefer and click Next. 5. Click Yes to accept the license. 6.
Modules & Options Sound Blaster Cinema & HDMI Sound Blaster Cinema Application Run the Sound Blaster Cinema control panel from the notification area of the taskbar (or from the item in the Apps screen). Click on the tabs to access the any of the control panel menus. Note that the Sound Blaster Cinema audio effects do not apply to audio generated through an HDMI connection.
Modules & Options Sound Blaster Cinema Settings Sound Blaster Cinema selects Stereo by default and this setting may cause some sound quality issues when using headphones. To adjust the settings for headphones do the following: 1. 2. 3. 4. Run the Sound Blaster Cinema application. Select Settings from the menu. Select Headphones from the drop-down menu (you can adjust the slider for crossover frequency). Click OK and close the application.
Modules & Options Settings Sound Blaster Cinema Controls Each control has an On/Off button to allow you to enable/disable the control, and most controls feature a slider to adjust the levels. You can use the drop down menu to use presets for Music, Movie or Games. Alternatively you can use a Custom setting. 7 Menu Figure 7 - 29 Sound Blaster Cinema Controls • • • • Surround: Provides virtual sound channels to control the level of immersion. Crystalizer: Enhances audio to make it sound livelier.
Modules & Options Sound Blaster Cinema & HDMI 1. 2. 3. When you connect an HDMI display to the HDMI-Out port, the Sound Blaster Cinema controls will be disabled. A warning box will pop-up and will prompt “Do you want to select another audio device now?”. Click No to continue using the HDMI audio output from your external display (do not attempt to select another audio device when connected to the external HDMI display).
Modules & Options Compatible Adapters For a list of compatible display and audio adapters check the Intel website, or your distributor/ supplier.
Modules & Options Wireless Display Configuration 1. 2. 3. 4. Note that no driver or application is required for wireless display in Windows 8.1. Go the Charms Bar, select Devices. Click Project. Click Add a wireless display.
Modules & Options 5. The system will then search for compatible display devices (this may take up to 60 seconds so allow time for this to complete). 6. 7. Double-click any detected display device in the list. You may then need to input a pin number for the device to which you are connecting. Click Next. Figure 7 - 32 Searching For Devices 7 8.
Modules & Options 9. The display will then connect (for specific settings for your display see the documentation supplied with your compatible adapter/display for full details). 10. To disconnect from the display you can select it in PC and Devices > Devices and click Remove Device > Yes; or go to the Project menu (Charms Bar > Devices) and click Disconnect.
Modules & Options Wireless Device Operation Aboard Aircraft 7 The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the WLAN, Bluetooth & 3G module(s) are OFF if you are using the computer aboard aircraft by putting the system in to Airplane Mode (see Table 1 - 4, on page 1 12).
Modules & Options 3G Module USIM Card Installation Follow the instructions below to install the USIM card (which will be provided by your service provider). 1. 2. 3. 4. 5. Turn off the computer, and turn it over. Slide the latch 1 in the direction of the arrow. Slide the latch 2 in the direction of the arrow, and hold it in place. Remove the battery 3 . Insert the USIM card 4 (at the rear of the battery compartment) as illustrated below until it clicks fully into position, and replace the battery.
Modules & Options 3G Configuration in Windows You can configure a 3G connection as below, however make sure the system is not in Airplane Mode before configuration begins. Charms Bar 1. 2. \ 3. 7 Figure 7 - 36 Networks Mobile Broadband 7 - 42 3G Module Go to the Charms Bar. Select Settings and then click the WiFi icon (it should read Available under the icon and Airplane mode should be Off). A list of available access points will appear under Mobile Broadband.
Modules & Options 4. 5. Any 3G service provider (connection information is usually stored on the USIM card) will appear under Mobile Broadband. Double-click any connection icon under Mobile Broadband (or click and then click Connect). Figure 7 - 37 Mobile Broadband (Connect) 7 6. 7. The system will connect to your network. A Connected will appear alongside the 3G connection (click the connection to view the timer which indicates your connected time for the current session).
Modules & Options Wireless Device Operation Aboard Aircraft 8. 9. You can then access the internet, download e-mail etc. as per any internet connection. To disconnect you can select the connection and click Disconnect . The use of any portable electronic transmission devices aboard aircraft is usually prohibited. 7 Make sure the system is in Airplane Mode if you are using the computer aboard aircraft. Figure 7 - 38 Mobile Broadband (Disconnect) 7 - 44 3G Module 10.
Modules & Options EM820W 3G Module PIN Code & Power-Saving Note that there may be some issues when a PIN Code is set for the EM820W 3G module (if you are unsure of your module version contact your distributor/supplier) in Windows, if Mobile Broadband has been turned off, and the system has resumed from a power-saving state. To prevent any issues it is recommended that you simply do not enable a PIN for the EM820W 3G module.
Modules & Options 3. 4. 5. 6. 7. 7 Click Network. Click the broadband connection under Mobile Broadband. Scroll down to Security and click Remove PIN. Enter the current PIN number and click OK. It is recommended that you do not Enable a PIN for the EM820W 3G module.
Troubleshooting Chapter 8: Troubleshooting Overview Should you have any problems with your computer, before consulting your service representative, you may want to try to solve the problem yourself. This chapter lists some common problems and their possible solutions. This can’t anticipate every problem, but you should check here before you panic. If you don’t find the answer in these pages, make sure you have followed the instructions carefully and observed the safety precautions in the preface.
Troubleshooting Basic Hints and Tips Many of the following may seem obvious but they are often the solution to a problem when your computer appears not to be working. • Power - Is the computer actually plugged into a working electrical outlet? If plugged into a power strip, make sure it is actually working. Check the LED Power & Communication Indicators (see “LED Indicators” on page 1 - 9) to see the computer’s power status.
Troubleshooting Backup and General Maintenance • Always backup your important data, and keep copies of your OS and programs safe, but close to hand. Don’t forget to note the serial numbers if you are storing them out of their original cases, e.g. in a CD wallet. • Run maintenance programs on your hard disk and OS as often as you can. You may schedule these programs to run at times when you are not using your computer.
Troubleshooting Viruses • Install an Anti-Virus program and keep the definitions file (the file which tells your program which viruses to look for) up to date. New computer viruses are discovered daily, and some of them may seriously harm your computer and cause you to lose data. Anti-Virus programs are commercially available and the definitions file updates are usually downloadable directly from the internet. • Be careful when opening e-mail from sources you don’t know.
Troubleshooting Upgrading and Adding New Hardware/Software • Do not be tempted to make changes to your Windows Registry unless you are very sure of what you are doing, otherwise you will risk severely damaging your system. • Don’t open your computer or undertake any repair or upgrade work if you are not comfortable with what you are doing. • Read the documentation.
Troubleshooting • Thoroughly check any recent changes you made to your system as these changes may affect one or more system components, or software programs. If possible, go back and undo the change you just made and see if the problem still occurs. • Don’t over complicate things.
Troubleshooting Problems and Possible Solutions Problem Possible Cause - Solution You turned on the power but it doesn’t work. You are setting the computer up for the first time and trying to power the computer from the battery only. You should power the computer from the AC/ DC adapter when first setting up the computer. As a safeguard during shipping, the battery will be locked and will not power the computer until first connected to the AC/DC adapter. The battery LED power indicator blinking orange.
Troubleshooting Problem The computer feels too hot. Possible Cause - Solution Make sure the computer is properly ventilated and the Vent/Fan intakes are not blocked. If this doesn’t cool it down, put the system into Hibernate mode or turn it off for an hour. Make sure the computer isn’t sitting on a thermal surface (see “Overheating” on page 1 - 20). Make sure you’re using the correct adapter.
Troubleshooting Problem Possible Cause - Solution You forget the boot password. If you forget the password, you may have to discharge the battery of the CMOS. Contact your service representative for help. Password Warning If you choose to set a boot password, NEVER forget your password. The consequences of this could be serious. If you cannot remember your boot password you must contact your vendor and you may lose all of the information on your hard disk.
Troubleshooting Problem Possible Cause - Solution I am sliding my finger up and down on the right side of the Touchpad to scroll a Window and the Touchpad does not respond. There are different Touchpad versions available on this computer, and this version requires tapping/holding to scroll. Either tap repeatedly, or hold the finger down, at the top or bottom right of the Touchpad (depending on the scrolling direction required) to scroll the window.
Troubleshooting Problem Possible Cause - Solution The Wireless LAN/Bluetooth modules cannot be detected. The modules are off as the computer is in Airplane Mode. Check the LED indicator to see if it is in Airplane Mode (see “LED Indicators” on page 1 9). Use the Fn + F11 key combination to toggle Airplane Mode on/off (see Table 1 - 4, on page 1 - 12). The PC Camera module cannot be detected. The module is off.
Troubleshooting Problem Possible Cause - Solution I have used Update Driver in Device Manager (Unknown device > Other Devices) to try and install the Airplane Mode driver. Windows encountered a problem in attempting to update the driver, and a yellow exclamation mark appears in Device Manager against the Unknown device. It is very important that the drivers are installed in the order indicated in Chapter 4 (which is the numbered installation order on the Device Drivers & Utilities + User’s Manual disc).
Troubleshooting Problem Possible Cause - Solution I have connected a Bluetooth Mouse but it loses the Bluetooth connection and no longer responds after a short period of inactivity. This is an issue with some mouse models and the Intel Wireless 7260 WLAN and Bluetooth combo module series. To resolve this issue do the following: 1. 2. 3. 4. 5. 6. Go to the Device Manager control panel in Windows. Click the arrow alongside Bluetooth to expand the menu if required.
Troubleshooting Problem Possible Cause - Solution When using a Bluetooth headset the audio appears to be mono and not stereo. This is a common issue with Bluetooth headsets. To resolve this issue do the following (you will need to repeat this procedure after every boot up, restart, or when the system resumes from hibernation): 1. 2. 3. Go to the Devices & Printers control panel in Windows. Double-click the Bluetooth headset. Click Connect to complete the stereo connection. OR 1. 2. 3.
Troubleshooting EM820W 3G Module PIN Code & Power-Saving Note that there may be some issues when a PIN Code is set for the EM820W 3G module (if you are unsure of your module version contact your distributor/supplier) in Windows, if Mobile Broadband has been turned off, and the system has resumed from a power-saving state. To prevent any issues it is recommended that you simply do not enable a PIN for the EM820W 3G module. The following provides instructions for disabling the PIN code.
Troubleshooting 3. 4. 5. 6. 7. Click Network. Click the broadband connection under Mobile Broadband. Scroll down to Security and click Remove PIN. Enter the current PIN number and click OK. It is recommended that you do not Enable a PIN for the EM820W 3G module.
Troubleshooting Resolving the “Insert a SIM” issue with the 3G Module (Windows 8.1) 1. 2. 3. 4. 5. 6. 7. 8. 9. If a PIN was set for the EM820W 3G module, you have then switched Mobile broadband off (or put the system in Airplane Mode) in Networks, and the system has just resumed from a power-saving state the following error may occur. On resuming from the power-saving state the standard procedure would be to go to Networks in the Charms Bar and turn on Mobile broadband. Go to the Charms Bar.
Troubleshooting 8 8 - 18
Interface (Ports & Jacks) Appendix A: Interface (Ports & Jacks) Overview The following chapter will give a quick description of the interface (ports & jacks) which allow your computer to communicate with external devices, connect to the internet etc.
Interface (Ports & Jacks) Notebook Ports and Jacks Item Description Card Reader Port The card reader allows you to use some of the latest digital storage cards. Push the card into the slot and it will appear as a removable device. DC-In Jack A Plug the supplied AC/DC adapter into this jack to power your computer. External Monitor (VGA) Port This port allows you to connect an external monitor, or Flat Panel Display, to get dual video or simultaneous display on the LCD and external monitor/FPD.
Interface (Ports & Jacks) Item Description Headphone-Out Jack Headphones or speakers may be connected through this jack. Note: Set your system’s volume to a reduced level before connecting to this jack. Microphone-In Jack Plug an external microphone in to this jack to record on your computer. RJ-45 LAN Jack This port supports LAN (Network) functions. Note: Broadband (e.g. ADSL) modems usually connect to the LAN port.
Interface (Ports & Jacks) A A - 4
Control Center Appendix B: Control Center Overview The following chapter will give a quick description of the functions of the Control Center. The Control Center gives quick access to frequently used controls, power management features and enables you to quickly turn modules on/off. Click the Control Center icons to toggle the appropriate function, or hold the mouse button down and move the slider where applicable. Certain functions will automatically be adjusted when a power mode is selected.
Control Center Power Modes You can set a Power Mode by clicking the appropriate icon at the top of the Control Center. Each power mode will affect screen brightness, Touchpad and PC camera power etc. You can click a Control Center icon to set an overall power mode and then click individual icons in the Control Center to power on/off the Touchpad and PC camera.
Control Center Power Status The Power Status icon will show whether you are currently powered by the battery, or by the AC/DC adapter plugged in to a working power outlet. The power status bar will show the current battery charge state. Brightness The Brightness icon will show the current screen brightness level. You can use the slider to adjust the screen brightness or the Fn + F8/F9 key combinations, or use the Fn+ F2 key combination to turn off the LED backlight (press any key to turn it on again).
Control Center Sleep Click the Sleep button to bring up the Hibernate or Sleep buttons, and click either button to have the computer enter the appropriate power-saving mode (see “Power-Saving States” on page 3 - 7). Display Switch Click the Display Switch button to access the menu (or use the priate attached display mode. + P key combination) and select the appro- Time Zone Clicking the Time Zone button will access the Date and Time Windows control panel.
Video Driver Controls Appendix C: Video Driver Controls The basic settings for configuring the LCD are outlined in “Video Features” on page 1 - 33. Make sure you install the drivers in the order indicated in Table 4 - 1, on page 4 - 4. Video (VGA) 1. Click 2.Install VGA Driver > Yes. 2. Click Next > Yes > Next > Next. 3. Click Finish to restart the computer. NVIDIA Video (VGA) 1. Click 3.Install nVIDIA VGA Driver > Yes. 2. Click AGREE AND CONTINUE (button) to accept the terms of the license agreement. 3.
Video Driver Controls Microsoft Hybrid Graphics Most notebook computers come with either a discrete or integrated graphics solution. Discrete graphics solutions feature a dedicated Graphics Processing Unit (GPU) which are capable of playing games, watching HD video or running GPU-based applications. However computers with discrete graphics solutions tend to be heavy in power consumption, and slightly larger in size in order to incorporate the dedicated discrete GPU.
Video Driver Controls How the Technology works When the system is powered up and is displaying just the desktop, the dGPU will be powered off. In this case the system is running in the same way as a system without a discrete graphics solution. However when an application that requires use of the dGPU is run (e.g, a game or HD Video), the dGPu is powered on and takes over the processing duties. If the program is closed, then the dGPU will be powered back down again until required.
Video Driver Controls Intel® HD Graphics Control Panel Advanced video configuration options are provided by the Intel® HD Control Panel. To access the control panel see below and overleaf: 1. Click the Intel® HD Graphics Control Panel icon in the Apps screen.
Video Driver Controls OR 2. Right-click the Desktop and select Graphics Properties from the menu. OR 3. 4. 5. Click Advanced settings in the Screen Resolution control panel in Windows. Click the Intel(R) HD Graphics Control Panel tab and click Graphics Properties (button). Double-click the Intel(R) HD Graphics control panel in the Windows Control Panel.
Video Driver Controls You may make changes to any of the graphics properties by clicking the appropriate menu panel and adjusting the settings from the menus.
Video Driver Controls Sub-Menus Some of the menu panels will also have sub-menus (in the top left corner of the menu alongside the icon ) to display further configuration options.
Video Driver Controls Multiple Display Display Click either Display Settings or Color to make display adjustments, including configuration for any attached external displays. At least one other display must be attached in order to view multiple display selection options.
Video Driver Controls Click the Display menu at the top of the screen to display the sub-menus. The Multiple Displays menu allows you to configure the display mode of any attached displays (see “Attaching Other Displays” on page C - 15). Multiple Display At least one other display must be attached in order to view multiple display selection options.
Video Driver Controls 3D This menu allows you to choose how 3D images are displayed. Quality displays the most detail, Balanced provides better computer performance with good quality and Custom allows you to configure the Anisotropic Filtering, Vertical Sync and Application Optimal Mode features to your preferences. Click Apply to save changes.
Video Driver Controls Options Options allows you to Customize Hot Keys (for opening the application, rotating the display, scaling etc.) to your preferences. Click Apply to save changes.
Video Driver Controls Preferences Click the Options menu at the top of the screen to display the sub-menus. The Information Center provides details on System Information, the Built-In Display and any attached displays. Go to the Preferences sub-menu in Options to configure the preferences for the Intel® HD Graphics Control Panel. Make sure you turn Tray Icon On to display the Intel® HD Graphics Control Panel icon in the notification area of the taskbar (as below).
Video Driver Controls Click the Video menu at the top of the screen to display the sub-menus. The Image Enhancement menu allows you to adjust the Sharpness and Skin Tone Enhancement. Click Apply to save changes.
Video Driver Controls Display Devices & Options Note that you can use external displays connected to the HDMI-Out port and/or external monitor port. See your display device manual to see which formats are supported. Attaching Displays When you first attach an external display you may find that the desktop does not occupy the full screen area. Use either the display’s auto adjust/configure controls, or the Intel(R) HD Graphics Control Panel to configure the full screen display.
Video Driver Controls Attaching Other Displays To Clone Displays: 1. 2. 3. 4. 5. Attach your external display to the external monitor port/HDMI-Out port, and turn it on. Go to the Intel(R) HD Graphics Control Panel control panel and click Display > Multiple Displays (sub-menu). Click Clone from the Select Multiple Display Mode menu. Click Apply, and OK to confirm the settings change. You can select the displays to be used from the Select Active Displays menu.
Video Driver Controls To Enable Extended Mode: Display Settings Extended Desktop You can have different Colors, Screen Area and Monitor Refresh Rates for each display device provided your monitor can support them. 1. 2. 3. 4. Attach your external display to the HDMI-Out port/external monitor port, and turn it on. Go to the Intel(R) HD Graphics Control Panel control panel and click Display > Multiple Displays (sub-menu). Click Extended from the Select Multiple Display Mode menu.
Video Driver Controls To Enable Collage Mode: 1. 2. 3. 4. 5. 6. Attach your external displays to the external monitor port and HDMI-Out port, and turn them on. Go to the Intel(R) HD Graphics Control Panel control panel and click Display > Multiple Displays (sub-menu). Click Collage from the Select Multiple Display Mode menu. Click Enable Collage and click On. Click Vertical or Horizontal to arrange and displays as required. Click Apply, and OK to confirm the settings change.
Video Driver Controls Windows Logo Key + P Key Combination You can use the +P key combination to quickly bring up the Second Screen menu. Attaching Other Displays - Devices (Charms Bar) You can configure attached displays from Devices (in the Charms Bar). 1. 2. 3. 4. Attach your external display to the external monitor port/HDMI-Out port, and turn it on. Go the Charms Bar, select Devices. Click Project (you may need to click Second Screen).
Video Driver Controls Configuring an External Display In Windows 1. 2. 3. 4. Attach your external display to the external monitor port/HDMI-Out port, and turn it on. Go to the Screen resolution control panel (see page 1 - 38) in the Desktop app. Click the Detect button. The computer will then detect any attached displays.
Video Driver Controls 5. You can configure the displays from the Multiple Displays menu. Figure C - 16 Screen Resolution Multiple Display Options C • Duplicate these displays - Shows an exact copy of the main display desktop on the other display(s) • Extend these displays - Treats both connected displays as separate devices • Show desktop only on 1/2 - Only one of your displays is used.
Video Driver Controls NVIDIA Control Panel More advanced video configuration options are provided in the NVIDIA Control Panel tab. 1. 2. Go to the Control Panel. Double-click NVIDIA Control Panel (click to view the control panel in either Large icons or Small icons if you are in Category view). NVIDIA Control Panel To access the GeForce..... control panel from the desktop; rightclick the desktop, then click NVIDIA Control Panel. Figure C - 17 NVIDIA GeForce.....
Video Driver Controls Navigating the Control Panel The NVIDIA Control Panel provides additional video configuration controls and tools which allow quick access to features such as image settings, 3D Settings and video configuration. Navigate through the control panels in much the same way as you would a web page. Click on the sub-heading tasks in the left menu (and on the highlighted links) for information. Use the buttons on the top left to go back, forward etc.
Video Driver Controls Customization Options One of the most important aspects of hybrid graphics technology is that it will switch between the integrated GPU and discrete GPU seamlessly and automatically, and does not require any input from the user. However customization options are offered for users who prefer to set their own parameters for GPU usage.
Video Driver Controls iGPU or dGPU Note the NVIDIA control panel refers to High-performance NVIDIA processor (which is the discrete GPU) and Integrated graphics (which is the integrated GPU). 3. 4. 5. 6. Close the NVIDIA Control Panel. Find the executable file icon of the application you want to run. Right-click the icon and select Run with graphics processor from the context menu.
Video Driver Controls Global Settings Global settings allows you to set the preferred graphics processor for overall use. Ideally this would be the iGPU for battery life, but this can be set to the dGPU if preferred. 1. 2. 3. 4. 5. Go to the NVIDIA Control Panel (see page C - 21). Click Manage 3D Settings (3D Settings) and select Global Settings (tab). Select either Integrated graphics (iGPU) or High performance NVIDIA Processor (dGPU) from the drop-down menu.
Video Driver Controls Program Settings Program settings allows you to make specific adjustments for installed applications. 1. 2. 3. 4. 5. 6. Go to the NVIDIA Control Panel (see page C - 21). Click Manage 3D Settings (3D Settings) and select Program Settings (tab). Select a program to customize from the drop-down menu, or click Add to add any program that does not appear in the menu. Select the preferred graphics processor for the program from the drop-down menu.
Video Driver Controls Set PhysX® Configuration NVIDIA® PhysX® is a physics engine that can use the GPU to accelerate game and 3D application performance. You can select the GeForce video card or CPU as a PhysX® processor, or configure the computer to auto-select a PhysX® processor (recommended default setting). 1. 2. 3. 4. Go to NVIDIA Control Panel (see page C - 21). Click Set PhysX configuration. Click to Select a PhysX processor from the menu; Auto-select (recommended) is the default setting.
Video Driver Controls Volume Adjustment The sound volume level can be set using the volume control in the Settings menu in the Charms Bar. HDMI Audio Configuration HDMI (High-Definition Multimedia Interface) carries both audio and video signals. In some cases it will be necessary to go to the Sound control panel and manually configure the HDMI audio output as per the instructions below. 1. 2. 3. 4. C Go to the Control Panel.
Video Driver Controls 5. 6. Adjust the HDMI settings from the control panel tabs. Click OK to close the Sound control panel.
Video Driver Controls Other Applications If you are using a third party application to play DVDs etc. from any attached DVD device, you will need to consult the application’s documentation to see the appropriate audio configuration (the application must support digital to analog translation). HDMI Notes • Connect a device with HDMI support to the HDMI-Out port BEFORE attempting to play audio/video sources through the device.
Specifications Appendix D: Specifications Latest Specification Information The specifications listed in this Appendix are correct at the time of going to press. Certain items (particularly processor types/ speeds and CD/DVD device types) may be changed, updated or delayed due to the manufacturer's release schedule. Check with your distributor/supplier for details.
Specifications Processors Intel® Core™ i7-4900MQ (2.80GHz) Processor 8M L3 Cache, 22nm (22 Nanometer), DDR3L-1600MHz, TDP 47W Intel® Core™ i7-4800MQ (2.70GHz) Processor 6M L3 Cache, 22nm (22 Nanometer), DDR3L-1600MHz, TDP 47W Intel® Core™ i7-4700MQ (2.40GHz) Processor 6M L3 Cache, 22nm (22 Nanometer), DDR3L-1600MHz, TDP 47W Intel® Core ™i7-4600M (2.9GHz) Mobile Processor 4M L3 Cache, 22nm (22 Nanometer), DDR3L-1600MHz, TDP 37W Intel® Core™ i5-4330M (2.
Specifications Intel® Integrated GPU and NVIDIA® GeForce 840M or GTX 850M Video: Intel® HD Graphics 4600 / Intel® HD Graphics (GPU is Dependent on Processor): Dynamic Frequency Intel Dynamic Video Memory Technology up to 1.7MB Microsoft DirectX®11 Compatible ======================================= For Models A & C: NVIDIA® GeForce 840M Discrete GPU: 2GB DDR3 Video RAM Supports PCIe * 8 Microsoft DirectX®11.
Specifications Card Reader Embedded Multi-In-1 Card Reader - MMC/ RS MMC - SD/ Mini SD / SDHC/ SDXC - MS/ MS Pro/ MS Duo Note: Some of these cards require PC adapters that are usually supplied with the cards. Slot Two Mini-Card Slots: Slot 1 for Half Size Mini-Card WLAN Combo Module with PCIe & USB Interfaces: Intel® Dual Band Wireless AC 7260 (2*2 802.11a/c) Half Mini-Card PCIe WLAN + Bluetooth Combo Module (Factory Option) Intel® Dual Band Wireless-N 7260 (2*2 802.
Specifications Battery Features Removable 6 Cell Smart Lithium Ion Battery Pack 62.16WH (Factory Option) Painted Style (For some Model A & B Designs in this series) Removable 6 Cell Smart Lithium Ion Battery Pack 48.84WH (Factory Option) IMR (Injected Molded Resin) LCD Back Covers (For some Model C & D Designs in this series) Power Management Supports Wake on LAN Supports Wake on USB Supports Wake on RTC Alarm (AC Mode Only) Operating System Windows® 8.
Specifications D D - 6
