Preface Notice The company reserves the right to revise this publication or to change its contents without notice. Information contained herein is for reference only and does not constitute a commitment on the part of the manufacturer or any subsequent vendor. They assume no responsibility or liability for any errors or inaccuracies that may appear in this publication nor are they in anyway responsible for any loss or damage resulting from the use (or misuse) of this publication.
Preface FCC Statement (Federal Communications Commission) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Preface IMPORTANT SAFETY INSTRUCTIONS Follow basic safety precautions, including those listed below, to reduce the risk of fire, electric shock, and injury to persons when using any electrical equipment: 1. 2. 3. 4. 5. Do not use this product near water, for example near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool. Avoid using this equipment with a telephone line (other than a cordless type) during an electrical storm.
Preface Instructions for Care and Operation The computer is quite rugged, but it can be damaged. To prevent this, follow these suggestions: 1. Don’t drop it, or expose it to shock. If the computer falls, the case and the components could be damaged. 2. Keep it dry, and don’t overheat it. Keep the computer and power supply away from any kind of heating element. This is an electrical appliance. If water or any other liquid gets into it, the computer could be badly damaged. 3. Avoid interference.
Preface Power Safety The computer has specific power requirements: • • • When you want to unplug the power cord, be sure to disconnect it by the plug head, not by its wire. Make sure the socket and any extension cord(s) you use can support the total current load of all the connected devices. Before cleaning the computer, make sure it is disconnected from any external power supplies. Do not plug in the power cord if you are wet. Do not use the power cord if it is broken.
Preface Cleaning Do not apply cleaner directly to the computer, use a soft clean cloth. Do not use volatile (petroleum distillates) or abrasive cleaners on any part of the computer. Servicing Do not attempt to service the computer yourself. Doing so may violate your warranty and expose you and the computer to electric shock. Refer all servicing to authorized service personnel. Unplug the computer from the power supply.
Preface Ergonomics We designed your LCD PC system to be functional as well as attractive. To get most out of it, here are some suggestions on how to position and use the computer: • The top third of the LCD (screen) should be at eye-level or slightly below. • The LCD should be at least 18"/45cm. directly in front of you. • If the screen resolution (e.g. 1024x768) makes you strain to read, change it: In Windows Control Panel, double-click Display (icon) and click Settings (tab).
Preface VIII
Preface Contents Notice ..............................................................................I FCC Statement ................................................................II Instructions for Care and Operation ........................ IV Power Safety ............................................................. V Cleaning ................................................................... VI Servicing .................................................................. VI Ergonomics ..............
Preface Inserting and Removing PC Cards ..........................2-13 Power Management ...................................................2-14 Power Schemes ........................................................2-15 System Power Options ............................................2-16 Hibernate Mode vs. Shutdown ...............................2-16 Standby Mode vs. Hibernate Mode ........................2-16 Standby ...................................................................2-17 Hibernate ........
Preface System Time & Date (Main Menu) .............................4-6 Legacy Diskette A: (Main Menu) ................................4-7 IDE Channel 0/1 Master (Main Menu) .......................4-7 System/Extended Memory (Main Menu) ....................4-7 Advanced Menu ...........................................................4-8 Chipset Information Menu (Advanced Menu) ............4-8 National 392 SIO Control Sub-Menu ..........................4-8 Reset Configuration Data: (Advanced Menu) ............
Preface Specifications Processor Types .......................................................... B-2 Core Logic .................................................................. B-2 LCD ............................................................................ B-2 Memory ...................................................................... B-3 Video Controller ......................................................... B-3 BIOS ...........................................................................
Quick Start Guide Chapter 1: Quick Start Guide Overview This Quick Start Guide is a brief introduction to the basic features of your computer, to navigating around the computer and to getting your system started.
1 Quick Start Guide Advanced Users If you are an advanced user you may skip over most of this Quick Start Guide. However you may find it useful to refer to “What to Install” on page 3 - 1, “BIOS Utilities” on page 4 - 1 and “Upgrading The Computer” on page 5 - 1 in the User’s Manual. You may also find the notes marked with a of interest to you. Notes Check the light colored boxes with the mark above to find detailed information about the computer’s features.
Quick Start Guide Not Included Operating Systems (e.g. Windows XP etc.) and applications (e.g. word processing, spreadsheet and database programs) have their own manuals, so please consult the appropriate manuals. System Software Your computer may already come with system software pre-installed.
1 Quick Start Guide System Startup 1. 2. 3. 4. Remove all packing materials, CDs/DVDs, floppy disks, and any PC Cards. Securely attach any peripherals you want to use with the computer (e.g. keyboard and mouse) to their ports. Attach the AC power cord to the AC-In jack on the right of the computer. Then plug the AC power cord into an outlet. Push the power button to turn the computer “on”.
Quick Start Guide Model Types and Design Differences There two model types (pictured below) in this LCD PC series. The model types differ in physical appearance (Model A’s optical CD/DVD device bay is located on the left side of the computer; Model B’s is at the front) and their specifications.
1 Quick Start Guide System Map: Front View 1. 2. 3. 4. 5. 6. LCD Panel Speakers LED Indicators Power Button Optical (CD/DVD) Device Bay (Model B Only - see page 1 - 10 for Model A) Keyboard Holder (Model B Only) Model A Model B 1 1 CD/DVD Emergency Eject If you need to manually eject a CD/DVD (e.g. due to an unexpected power interruption) you may push the end of a straightened paper clip into the emergency eject hole.
Quick Start Guide LED Indicators Power Button The LED indicators on the computer display helpful information about the current status of the computer. When the computer is on, you can use the power button as a hot-key button when it is pressed for less than 4 seconds. Use Power Options in the “Windows” control panel to configure this feature.
1 Quick Start Guide Optical (CD/DVD) Device There is a bay for a 5.25" optical (CD/DVD) device (12.7mm height). The actual device will depend on the model you purchased (see “Storage” on page B - 3). The optical device is usually labeled “Drive D:” and may be used as a boot device if properly set in the BIOS (see “Boot Menu” on page 4 - 12).
Quick Start Guide DVD Regional Codes DVD region detection is device dependent, not OS-dependent. You can select your module’s region code 5 times. The fifth selection is permanent. This cannot be altered even if you change your operating system or you use the module in another computer. Changing DVD Regional Codes 1. 2. 3. Go to the Control Panel and double-click System > Hardware (tab). Click Device Manager, then click the + next to DVD/CD-ROM drives.
1 Quick Start Guide System Map: Left View Figure 1 - 4 - Left View 1. 2. 3. 4. Floppy Disk Drive Module Vent Hard Disk Drive Bay Optical (CD/DVD) Device Bay (Model A Only) Overheating 1 2 CD/DVD Emergency Eject If you need to manually eject a CD/ DVD (e.g. due to an unexpected power interruption) you may push the end of a straightened paper clip into the emergency eject hole. Do not use a sharpened pencil or similar object that may break and become lodged in the hole.
Quick Start Guide System Map: Right View Figure 1 - 5 - Right View 1. 7-in-1 Card Reader Formats The card reader allows you to use the most popular digital storage card formats (see page 2 - 12): • • • • • • • 9 1 2 MMC (MultiMedia Card) SD (Secure Digital) MS (Memory Stick) MS Pro (Memory Stick Pro) MS Duo (requires PC adapter) Mini SD (requires PC adapter) RS MCC (requires PC adapter) The PC Card Slot 4 3 The computer is equipped with a PCMCIA 3.3V/5V slot (see page 2 - 13).
1 Quick Start Guide System Map: Rear View Figure 1 - 6 - Rear View 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. Carrying Handle Headphone-Out Jack Line-In Jack Microphone-In Jack RJ-45 LAN Jack RJ-11 Phone Jack 2 * USB 2.
Quick Start Guide Windows XP Start Menu & Control Panel Most of the control panels, utilities and programs within Windows XP (and most other Windows versions) are accessed from the Start menu. When you install programs and utilities they will be installed on your hard disk drive, and a shortcut will usually be placed in the Start menu and/or the desktop. To customize the look of the Start menu, right-click Start, and select Properties from the menu.
1 Quick Start Guide Video Features Your computer has built-in Intel on-board video. You can switch display devices, and configure display options, from the Display Properties control panel in Windows as long as the appropriate video driver is installed (see “Advanced Video Controls” on page 2 - 2). To access Display Properties in Windows: 1. 2. 3. 4. 5. 6. 7. 8. 9. Click Start, point to Settings and click Control Panel (or just click Control Panel).
Quick Start Guide 1 2 3 Figure 1 - 8 - Display Properties Desktop Intel Display Mode Description Single Mode One of the connected displays is used as the display device Twin Mode This mode will drive multiple displays with the same content and resolutions, color quality etc.
1 Quick Start Guide Power Management Features The Power Options control panel in Windows (see page 1 - 13) allows you to configure power management features for your computer. You may conserve power through individual components such as the monitor or hard disk (by means of Power Schemes), or you may use either Standby or Hibernate mode to conserve power throughout the system (enable Hibernate support from the control panel as pictured in Figure 1 - 9).
Quick Start Guide Adding a Printer The most commonly used peripheral is a printer. The following conventions will help you to add a printer, however it is always best to refer to the printer manual for specific instructions and configuration options. USB Printer Most new printers have a USB interface connection. You may use any one of the ports to connect the printer. Install Instructions: 1. 2. 3. 4. 5. Set up the printer according to its instructions (unpacking, paper tray, toner/ink cartridge etc.).
1 Quick Start Guide 1 - 18
Advanced Controls Chapter 2: Advanced Controls Overview This chapter covers: • • • • • • • • • Advanced Video Controls Audio Features 7-in-1 Card Reader PC Card Slot Power Management Intel PRO/Wireless WLAN Module 802.11b/g WLAN Module Bluetooth Module Touch Panel Module Drivers You are unable to use most advanced controls until the necessary drivers and utilities are properly installed.
Advanced Controls 2 DVMT Notes The default memory setting is 128MB, and this may be adjusted to either 64MB or 224MB. See “Total Graphics Memory: (Advanced Menu)” on page 4 - 9. Advanced Video Controls This section is about making adjustments for the LCD display, and switching display devices. The basic settings for configuring the display are outlined in “Video Features” on page 1 - 14.
Advanced Controls Intel Graphics Properties More advanced video configuration options are provided by the Intel(R) Graphics Media Accelerator Driver for Mobile. 1. 2. 3. Open Display Properties (see “Video Features” on page 1 - 14) and click Advanced. Click the Intel(R)... tab and click Graphics Properties (button). You can also access Graphics Properties from the Windows Intel(R) GMA Driver for Mobile control panel, or from the taskbar icon menu.
Advanced Controls 2 Help Menus You may make changes to the devices, color, schemes, Hot Keys etc. by clicking the appropriate menu item or button. Click Information (button) to obtain useful information about the graphics properties of the computer, and see the Support tab in Information to get weblinks to the latest information on the Intel Website. Right-click on many of the items in the tabs to bring up the “What’s This?” button. Click the “What’s This?” button to bring up the help menu.
Advanced Controls Scheme Options Use Scheme Options to configure quick settings for applications which require specific resolution and color settings in order to run properly e.g. games, multimedia programs. To set the scheme options: 1. 2. 3. 4. 5. 6. 7. 8. 9. Open the Intel(R) GMA Driver for Mobile control panel (see “Intel Graphics Properties” on page 2 - 3). Configure your display configuration, resolution etc. as per your requirements from Display Settings. Click on Scheme Options (button).
Advanced Controls 2 Intel Display Note Note that the notebook (i.e. the built-in LCD) is the default Primary display device and may not be changed. Attaching Other Displays Besides the built-in LCD, you can also use an external monitor/flat panel display as a display device. The following are the display options: 1. 2. The built-in LCD OR an external monitor/flat panel display connected to the external monitor port (Single Display).
Advanced Controls Display Modes 2 Single Display Only one of your attached displays is used. Twin This mode will drive multiple displays with the same content and resolutions, color quality etc. See “Twin Mode Support” on page 2 - 8 for more information. Extended Desktop This mode allows a desktop to span multiple displays and acts as a large workspace. This creates a lot more screen area for display.
Advanced Controls 2 To Enable Intel(R) Dual Display Clone Mode Twin Mode Support The Twin mode option will only appear if the LCD PC (notebook) and external monitor support the same resolution (e.g. 1280 * 800). Check any documentation supplied with an external monitor to see supported resolutions. 1. 2. 3. 4. 5. Attach your external monitor to the external monitor port, and turn it on. Go to the Intel (R) GMA Driver for Mobile control panel (see “Intel Graphics Properties” on page 2 - 3).
Advanced Controls To Enable Extended Desktop Mode: 1. 2. 3. 4. 5. Attach your external monitor to the external monitor port, and turn it on. Go to the Intel (R) GMA Driver for Mobile control panel (see “Intel Graphics Properties” on page 2 - 3). Click to choose Extended Desktop from Display Device (tab). Click Apply, and OK to confirm the settings change. Click Display Settings to adjust the settings for the attached devices.
Advanced Controls 2 To Enable Extended Desktop (Display Properties) Display Settings Extended Desktop Use the control panel to drag the monitors to match the physical arrangement you wish to use. You can drag any icons or windows across to either display desktop, which makes it possible to have one program visible in one of the displays, and a different program visible in the other display. Figure 2 - 8 Display Properties (Extended Desktop) 2 - 10 Display Modes 1. 2. 3. 4. 5.
Advanced Controls Audio Features You can configure the audio options on your computer from the Sounds and Audio Devices Windows control panel (see Figure 1 - 7 on page 1 - 13), or from the Realtek HD Audio Manager icon in the taskbar/control panel (this will bring up the Realtek Audio Configuration menus). Sound Volume Adjustment How high the sound volume can be set depends on the setting of the volume control within Windows (and the volume control knob on the computer).
Advanced Controls 2 Card Reader Cover Make sure you keep the rubber cover provided in the card reader when not in use. This will help prevent foreign objects and/or dust getting in to the card reader. 7-in-1 Card Reader The card reader allows you to use some of the latest digital storage cards. Push the card into the slot and it will appear as a removable device, and can be accessed in the same way as your hard disk (s).
Advanced Controls PC Card Slot The computer is equipped with a PCMCIA 3.3V/5V slot for one type II PCMCIA CardBus PC Card Slot. Make sure you install the PCMCIA/Card Reader driver (see see “PCMCIA/Card Reader” on page 3 - 8). Inserting and Removing PC Cards • Align the PC Card with the slot and push it in until it locks into place. • To remove a PC Card, simply press the eject button 1 next to the slot. PC Card Slot Cover Make sure you keep the cover in the PC Card slot when not is use.
Advanced Controls 2 Shutdown Note that you should always shut your computer down by choosing the Shut Down/ Turn Off Computer command from the Start menu in Windows. This will help prevent hard disk or system problems. Power Management The computer uses the ACPI power management system to conserve power by controlling individual components of the computer (the monitor and hard disk drive) or the whole system. Using some form of power management greatly increases the life span of the LCD.
Advanced Controls Power Schemes You can set your computer to conserve power through individual components by means of Power Schemes. You can also adjust the settings for each scheme to set the monitor to turn off after a specified time, and the computer's hard disk motor to turn off if the hard disk drive has not been accessed for a specified period of time (if the system reads or writes data, the hard disk motor will be turned back on).
Advanced Controls 2 Power Button as Standby or Hibernate Button Fully ACPI-compliant operating systems, (such as Windows XP) allow you to use the OS’s “Power Options” control panel to set the power button to send the system into Standby or Hibernate mode (see your OS’s documentation, or “Configuring the Power Button” on page 2 - 18 for details). System Power Options You can use the system power options to stop the computer’s operation and restart where you left off.
Advanced Controls Standby Standby saves the least amount of power, but takes the shortest time to return to full operation. During Standby the hard disk is turned off, and the CPU is made to idle at its slowest speed. All open applications are retained in memory. When you are not using your computer for a certain length of time, which you specify in the operating system, it will enter Standby mode to save power.
Advanced Controls Configuring the Power Button 2 The power button may be set to send the computer in to either Standby or Hibernate mode (Figure 2 - 14). In Standby mode, the Power LED will flash orange. In Hibernate mode the Power LED will be off.
Advanced Controls Intel PRO/Wireless WLAN Module 2 If you have included an Intel PRO/Wireless 3945ABG (802.11a/b/g) PCIe WLAN module in your purchase option, make sure you install the drivers in the order indicated in Table 3 - 1, on page 3 - 6. To get help on the network settings you can view the User Guide from the Intel PROSet / Wireless menu.
Advanced Controls 2 User Guide You can view the User Guides from the Device Drivers & Utilities + User’s Manual CD-ROM. Click Optional (button) and then click the Unlock button. Click 1.Wireless Lan > Yes. Click View User Guide (button) as per Figure 2 15 on page 2 - 19. Intel WLAN Driver Installation 1. Insert the Device Drivers & Utilities + User’s Manual CD-ROM into the CD/DVD drive. 2. Click Optional > Yes. 3. Click 1.Install Wireless Lan Driver > Yes. OR Navigate (Browse..
Advanced Controls 802.11b/g WLAN Module 2 If your purchase option includes the 802.11b/g Wireless LAN module, follow the procedure below for driver installation instructions. You can then configure the options from the Wireless Configuration Utility by clicking the icon in the Windows control panel, or in the taskbar. Wireless LAN (802.11b/g) Driver Installation 1. Insert the Device Drivers & Utilities + User’s Manual CD-ROM into the CD/DVD drive. 2. Click Optional > Yes. 3. Click 1.
Advanced Controls 2 Network Connection Use the Windows Network Connections control panel to access available wireless networks (Start > Settings > Network Connections or Start > Connect To > Show all Connections). Figure 2 - 17 Wireless Network Control Panels 2 - 22 802.
Advanced Controls Bluetooth Module 2 If your purchase option includes the Bluetooth module, follow the procedure below for driver installation instructions. Bluetooth Driver Installation 1. Insert the Device Drivers & Utilities + User’s Manual CD-ROM into the CD/DVD drive. 2. Click Optional > Yes. 3. Click 2.Install Bluetooth Driver > Yes. OR Click Start (menu) > Run... and navigate (Browse...) to D:\Others\Bluetooth\SETUP.exe and click OK. 4. Click Install Drivers and Application v2.12. 5.
Advanced Controls 2 User Guide Send To Bluetooth View the BlueSoleil User Guides from the Help Menu (or press the F1 key) in the IVT Corporation BlueSoleil Main Window. Right-Click to select any file and scroll down to Send To... Bluetooth Device. The Manual in Adobe .pdf format is on the Device Drivers & Utilities + User’s Manual CDROM. Click Browse CD (button) and navigate (Browse...) D:\Others\Blueto tooth\Manual\Manual.pdf.
Advanced Controls Touch Panel Module If your purchase option includes the Touch Panel module, follow the procedure below for driver installation instructions. The Touch Panel is a device for pointing (controlling input positioning) on the computer’s display screen by sensing finger movement, and downward pressure. It is an alternative to the mouse; however, you can also add a mouse to your computer through one of the USB ports. Touch Panel Driver Installation 1.
Advanced Controls 2 Calibrating the Touch Panel 1. Help Guide 2. 3. 4. Open the Help file from Start > Programs/All Programs > TouchSet Touch Panel > Help for further information on using the Touch Panel. Configure the settings from the TouchSet Utility control panel (Start > Programs/ All Programs > TouchSet Touch Panel), or double-click the desktop icon . Click the Calibration tab and click the Calibrating Now button. Use the input device to touch the cross at the different positions on screen.
Drivers & Utilities Chapter 3: Drivers & Utilities This chapter deals with installing the drivers and utilities essential to the operation or improvement of some of the computer’s subsystems. The system takes advantage of some newer hardware components for which the latest versions of most available operating systems haven’t built in drivers and utilities. Thus, some of the system components won’t be auto-configured with an appropriate driver or utility during operating system installation.
Drivers & Utilities 3 Navigate (Browse..) to D: You will notice that many of the instructions for driver installation require you to “Navigate (Browse) to D:”. We assume that you will install all drivers and utilities from the built-in CD device and it is assigned to “Drive D:”. In addition, all file extensions can be seen In this case “D:” is the drive specified for your CD device. Not all computers are setup the same way, and some computers have the CD listed under a different drive letter - e.g.
Drivers & Utilities Service Packs Check the warnings on the following pages regarding installation of the appropriate Service Pack for your Windows XP OS. Make sure you have installed the appropriate Service Pack before installing all the drivers. Service Pack Installed To see which Service Pack is currently installed on your computer go to the General tab of the System control panel. Right-click the My Computer icon on the desktop or in the Start menu and select Properties.
Drivers & Utilities Authorized Driver Message 3 If you receive a message telling you that the driver you are installing is not authorized (Digital Signature Not Found), just click Yes or Continue Anyway to ignore the message and continue the installation procedure. You will receive this message in cases where the driver has been released after the version of Windows you are currently using. All the drivers provided will have already received certification for Windows.
Drivers & Utilities Driver Installation 1. Insert the Device Drivers & Utilities + User’s Manual CD-ROM and click Install WinXP Drivers (button) > Yes, or Optional (button) > Yes to access the Optional driver menu. 2. If you wish to install the drivers manually, see page 3 - 6. 3. Check the driver installation order from Table 3 - 1 on page 3 - 6 (the drivers must be installed in this order) which is the same as that listed in the Drivers Installer menu below.
Drivers & Utilities 3 Service Pack Installation WinXP SP2 Driver Page # Install the appropriate Service Pack for WinXP Page 3 - 3 Chipset Page 3 - 7 Video Page 3 - 7 New Hardware Found Audio Page 3 - 7 Modem Page 3 - 8 LAN Page 3 - 8 PCMCIA/Card Reader Page 3 - 8 If you see the message “New Hardware Found” (Found New Hardware Wizard) during the installation procedure (other than when outlined in the driver install procedure), click Cancel to close the window, and follow the installation
Drivers & Utilities Chipset 1. Click Install WinXP Drivers > Yes. 2. Click 1.Install Chipset Driver > Yes. OR Navigate (Browse..) to D:\Drivers\00Chipset\Setup.exe and click OK. 3. A DOS window will appear and the driver will begin to install. 4. Click Next > Yes > Next. 5. Click Finish to restart the computer. Video 1. Click Install WinXP Drivers > Yes. 2. Click 2.Install Video Driver > Yes. OR Navigate (Browse..) to D:\Drivers\01VGA\Setup.exe and click OK. 3. Click Next > Yes. 4.
Drivers & Utilities 3 Modem 1. Click Install WinXP Drivers > Yes. 2. Click 4.Install Modem Driver > Yes. OR Navigate (Browse...) to D:\Drivers\03Modem\setup.exe and click OK. 3. Click OK. 4. Double-click the icon in the taskbar to access the Motorola SM56 Modem Helper for configuration. Modem Country Selection Be sure to check if the modem country selection is appropriate for you (Control Panel > Phone and Modem Options). 3 - 8 Driver Installation LAN 1. Click Install WinXP Drivers > Yes. 2. Click 5.
Drivers & Utilities Wireless LAN Touch Panel See the installation procedure in “Intel WLAN Driver Installation” on page 2 - 20 or “Wireless LAN (802.11b/g) Driver Installation” on page 2 - 21. See the installation procedure in “Touch Panel Driver Installation” on page 2 - 25. Bluetooth See the installation procedure in “Bluetooth Driver Installation” on page 2 - 23.
Drivers & Utilities 3 3 - 10
BIOS Utilities Chapter 4: BIOS Utilities Overview This chapter gives a brief introduction to the computer’s built-in software: Diagnostics: The POST (Power-On Self Test) Configuration: The PhoenixBIOS Setup Utility BIOS Settings Warning Incorrect settings can cause your system to malfunction. To correct mistakes, return to Setup and restore the Setup Defaults with . If your computer has never been set up, or you are making important changes to the system (e.g.
BIOS Utilities POST Screen 4 1.BIOS information 2.CPU type 3.Memory status 4.Enter Setup prompt appears only during POST Note: The POST screen as pictured is for guideline purposes only. The POST screen on your computer may appear slightly different. The Power-On Self Test (POST) Each time you turn on the computer, the system takes a few seconds to conduct a POST, including a quick test of the on-board RAM (memory). As the POST proceeds, the computer will tell you if there is anything wrong.
BIOS Utilities Failing the POST Errors can be detected during the POST. There are two categories, “fatal” and “non-fatal”. Fatal Errors These stop the boot process and usually indicate there is something seriously wrong with your system. Take the computer to your service representative or authorized service center as soon as possible. Non-Fatal Errors This kind of error still allows you to boot.
BIOS Utilities The Setup Program The PhoenixBIOS Setup Utility tells the system how to configure itself and manage basic features and subsystems (e.g. port configuration). 4 Entering Setup To enter the PhoenixBIOS Setup Utility, turn on the computer and press F2 during the POST. The prompt (Press F2 to Enter Setup) seen in Figure 4 - 1 is usually present for a few seconds after you turn on the system. If you get a “Keyboard Error”, (usually because you pressed F2 too quickly) just press F2 again.
BIOS Utilities Setup Screens The following pages contain additional advice on portions of the Setup. Setup Menus Along the top of the screen is a menu bar with five (5) menu headings. When you select a heading, a new screen appears. Scroll through the features listed on each screen to make changes to Setup. Instructions on how to navigate each screen are in the box along the bottom of the screen.
BIOS Utilities Main Menu PhoenixBIOS Setup Utility Figure 4 - 2 Main Menu 4 Main Main Advanced System Time: Legacy Diskette A: IDE Channel 0 Master IDE Channel 1 Master F1 Esc Help Exit Boot Exit Item Specific Help [22:11:05] [08/31/2006] System Date: System Memory Extended Memory Security [1.44/1.25 MB 3½"] [82348MB SATA1] [CD-ROM] , , or selects field.
BIOS Utilities Legacy Diskette A: (Main Menu) This control allows you to enable/reconfigure the internal floppy disk drive. IDE Channel 0/1 Master (Main Menu) Press Enter here to open the sub-menu to show the configuration of hard disks and CD/DVD device(s) on the computer’s IDE Channels. Use the Auto (Type:) setting to have the items configured automatically for you. 4 System/Extended Memory (Main Menu) This item contain information on the system memory, and is not user configurable.
BIOS Utilities Advanced Menu Figure 4 - 3 Advanced Menu PhoenixBIOS Setup Utility Main Advanced Advanced Security Boot Exit Item Specific Help 4 Chipset Information Menu National 392 SIO Control Sub-Menu Reset Configuration Data: Legacy USB Support: Boot-time Diagnostic Screen: Power on Boot Beep: Total Graphics Memory: F1 Esc Help Exit Select Item Select Menu Display Chipset Infomation required [No] [Enabled] [Enabled] [Disabled] [128MB] -/+ Enter Change Values Select Sub-Menu F9 S
BIOS Utilities Reset Configuration Data: (Advanced Menu) This item is set to “No” as default. You can change the setting to “Yes” if you have installed a new add-on which has reconfigured the system, resulting in such a serious system conflict that the operating system is unable to boot. 4 Legacy USB Support: (Advanced Menu) Choose “Enabled” if you intend to use USB devices in systems which do not normally support USB functionality (e.g. DOS).
BIOS Utilities Security Menu PhoenixBIOS Setup Utility Security Menu Main 4 The changes you make here affect the access to the Setup utility itself, and also access to your machine as it boots up after you turn it on. These settings do not affect your machine or network passwords which will be set in your software OS.
BIOS Utilities Password on boot: (Security Menu) Specify whether or not a password should be entered to boot the computer. If “Enabled” is selected, only users who enter a correct password can boot the system (see the warning in the sidebar). The default setting is “Disabled”. Note: To clear existing passwords press Enter and type the existing password, then press Enter for the new password (without typing any password entry) and Enter again to confirm the password clearance.
BIOS Utilities Boot Menu PhoenixBIOS Setup Utility Figure 4 - 5 Boot Menu Main Advanced Security Boot Exit Item Specific Help 4 Boot priority order: 1: Legacy Floppy Drives 2: USB KEY: 3: IDE CD: TSSTcorpCD/DVDW TS-L632D-( 4: IDE HDD: HDS722580VLSA80-(S1) 5: PCI SCSI: 6: PCI BEV: 7: 8: Excluded from boot order: : USB HDD: : USB CDROM: F1 Esc Help Exit Select Item Select Menu -/+ Enter Keys used to view or configure devices: Up and Down arrows select a device.
BIOS Utilities Exit Menu Figure 4 - 6 PhoenixBIOS Setup Utility Main Advanced Security Boot Exit Menu Exit Item Specific Help 4 Exit Saving Changes Exit Discarding Changes Load Setup Defaults Discard Changes Save Changes F1 Esc Help Exit Select Item Select Menu Exit System Setup and save your changes to CMOS.
BIOS Utilities 4 4 - 14
Upgrading The Computer Chapter 5: Upgrading The Computer Overview This chapter contains information on upgrading the computer. Follow the steps outlined to make the desired upgrades. If you have any trouble or problems you can contact your service representative for further help.
Upgrading The Computer Power Safety Warning 5 Before you undertake any upgrade procedures, make sure that you have turned off the power, and disconnected all peripherals and cables (including telephone lines). When Not to Upgrade These procedures involve opening the system’s case, adding and sometimes replacing parts.
Upgrading The Computer Upgrading the Hard Disk Drive The hard disk drive is used to store your data internally in the computer. It is mounted at the left side and can be taken out to accommodate other 3.5" IDE hard disk drives of the same or higher capacity. 1. 2. 3. Unplug the power cord and disconnect all peripheral cables (including the phone line) from the computer. Turn off the computer and turn it around so that you may comfortably access the left side. Remove screw 1 from the HDD Bay 2 .
Upgrading The Computer 4. Pull the HDD assembly 3 out of the bay and disconnect cables 4 & 5 . Figure 5 - 2 Hard Disk Drive Assembly Removal 3 4 5 5 5. Remove screws 6 - 9 , and lift the hard disk out of the case. Figure 5 - 3 6 7 9 8 Hard Disk Drive Assembly Screws 6. Insert the new hard disk, and reverse the removal procedures to install the new hard disk.
Upgrading The Computer Upgrading the System Memory (RAM) The computer can accommodate up to 2GB of memory in two DIMM sockets. See “Memory” on page B - 3 for more details. 1. 2. 3. 4. Unplug the power cord and disconnect all peripheral cables (including the phone line) from the computer. Turn off the computer. Place the computer with its LCD display facing down on a clean, dry, level surface. Remove screws 1 - 11 from the rear of the computer.
Upgrading The Computer 5. 6. Carefully remove the rear cover 12 and set it aside. The memory sockets will now be visible at point 13 on the mainboard. Figure 5 - 5 Rear Case Removal 12 13 12 13 5 Model AModel 7. A Model B Carefully push the two latches ( 14 and 15 ) toward the sides of the socket to release the module. Figure 5 - 6 RAM Removal 8. 9. 14 15 14 15 Push the latches to release the second module if necessary. The module will “pop-up” slightly, and you may remove it.
Upgrading The Computer 10. Insert the new module. The module will only fit one way as defined by the pin alignment. 11. Make sure the module is seated as far into the slot as it will go (DO NOT FORCE IT). The latches will click into place on the sides of the module. Make sure they are secure. 5 Figure 5 - 7 RAM Module Insertion 12. Reverse the procedures to put the computer back together, and do not forget all the screws. When you restart the computer the new memory configuration should be registered. 13.
Upgrading The Computer Upgrading the Optical Device (Model A) 1. 2. 3. 4. 5 Unplug the power cord and disconnect all peripheral cables (including the phone line) from the computer. Turn off the computer. Place the computer with its LCD display facing down on a clean, dry, level surface. Remove screws 1 - 11 from the rear of the computer.
Upgrading The Computer 5. 6. Carefully remove the rear cover 12 and set it aside. The optical device will now be visible at point 13 on the mainboard. Figure 5 - 9 Model A Rear Case Removal 13 12 5 7. 8. 9. Remove screws 14 - 16 , and disconnect cable 17 , from the optical device. Remove the optical device, and remove the screws in order to separate the optical device from the bracket. Reverse the removal procedures to install the new optical device.
Upgrading The Computer Upgrading the Optical Device (Model B) 1. 2. 3. 4. 5 Unplug the power cord and disconnect all peripheral cables (including the phone line) from the computer. Locate the optical device eject switch and remove screw 1 . Push the optical device eject switch to slide the optical device assembly 2 out of the bay. Remove the optical device, and reverse the removal procedures to install the new optical device.
Troubleshooting Chapter 6: Troubleshooting Overview Should you have any problems with your computer, before consulting your service representative, you may want to try to solve the problem yourself. This chapter lists some common problems and their possible solutions. This can’t anticipate every problem, but you should check here before you panic. If you don’t find the answer in these pages, make sure you have followed the instructions carefully and observed the safety precautions in the preface.
Troubleshooting Basic Hints and Tips Many of the following may seem obvious but they are often the solution to a problem when your computer appears not to be working. • Power - Is the computer actually plugged into a working electrical outlet? If plugged into a power strip, make sure it is actually working. • Connections - Check all the cables to make sure that there are no loose connections anywhere.
Troubleshooting Backup and General Maintenance • Always backup your important data, and keep copies of your OS and programs safe, but close to hand. Don’t forget to note the serial numbers if you are storing them out of their original cases, e.g. in a CD wallet. • Run maintenance programs on your hard disk and OS as often as you can. You may schedule these programs to run at times when you are not using your computer.
Troubleshooting Viruses • Install an Anti-Virus program and keep the definitions file (the file which tells your program which viruses to look for) up to date. New computer viruses are discovered daily, and some of them may seriously harm your computer and cause you to lose data. Anti-Virus programs are commercially available and the definitions file updates are usually downloadable directly from the internet. 6 • Be careful when opening e-mail from sources you don’t know.
Troubleshooting Upgrading and Adding New Hardware/Software • Do not be tempted to make changes to your Windows Registry unless you are very sure of what you are doing, otherwise you will risk severely damaging your system. • Don’t open your computer or undertake any repair or upgrade work if you are not comfortable with what you are doing. • Read the documentation.
Troubleshooting • Thoroughly check any recent changes you made to your system as these changes may affect one or more system components, or software programs. If possible, go back and undo the change you just made and see if the problem still occurs. 6 • Don’t over complicate things.
Troubleshooting Problems & Possible Solutions Problem Nothing screen. appears You forget password. Possible Cause - Solution on The screen saver is activated. Press any key or move the mouse to return to your display. \ The system is in a power saving mode. Press the power button for less than 4 seconds. If the computer does not turn on again then it was most likely shut down, or has no power source. Check the cables, outlets, power strips etc. (see “Configuring the Power Button” on page 2 18).
Troubleshooting Problem 6 Possible Cause - Solution The CD/DVD cannot be read. The CD/DVD is dirty. Clean it with a CD-ROM cleaner kit. The CD/DVD disc tray will not open when there is a disc in the tray. The CD/DVD disc is not correctly placed in the tray. Gently try to remove the disc using the eject hole (see “Loading Discs” on page 1 - 8). The DVD regional codes can no longer be changed. The code has been changed the maximum 5 times. See “Changing DVD Regional Codes” on page 1 - 9.
Interface (Ports & Jacks) Appendix A: Interface (Ports & Jacks) Overview The following chapter will give a quick description of the interface (ports & jacks) which allow your computer to communicate with external devices, connect to the internet etc. Item Description External Monitor Port Connect an external display to this port to allow dual video or simultaneous display on the LCD and external display (see “Attaching Other Displays” on page 2 - 6).
Interface (Ports & Jacks) Item Description IEEE 1394a Port This port will allow high speed connection to various peripheral devices, e.g. external disk drives and digital cameras (see note below). IEEE 1394 The IEEE 1394a port only supports SELF POWERED IEEE 1394 devices. Printer/Parallel Port This parallel printer port supports ECP (Extended Capabilities Port) and EPP (Enhanced Parallel Port) mode. RJ-11 Phone Jack This port connects to the built-in modem.
Interface (Ports & Jacks) Item Serial Port USB 2.0/1.1 Ports Description Connect a serial type mouse to this port. These USB 2.0 compatible ports (USB 2.0 is fully USB 1.1 compliant) are for low-speed peripherals such as keyboards, mice or scanners, and for high-speed peripherals such as external HDDs, digital video cameras or high-speed scanners etc.
Interface (Ports & Jacks) A A - 4
Specifications Appendix B: Specifications Latest Specification Information The specifications listed in this Appendix are correct at the time of going to press. Certain items (particularly processor types/speeds and CD/DVD device types) may be changed or updated due to the manufacturer's release schedule. Check with your service center for details.
Specifications Feature Processor Types B Specification Intel® Core™ 2 Duo Processor (478-pin) Micro-FC-PGA Package T7200/ T7400/ T7600 65nm (65 Nanometer) Process Technology 4MB On-die L2 Cache & 667MHz FSB 2.0/ 2.16/ 2.33 GHz Intel® Core™ 2 Duo Processor (478-pin) Micro-FC-PGA Package T5500/ T5600 65nm (65 Nanometer) Process Technology 2MB On-die L2 Cache & 667MHz FSB 1.66/ 1.
Specifications Feature Specification Security Security (Kensington® Type) Lock Slot BIOS Password Memory Two 200 Pin SO-DIMM Sockets Supporting DDRII (DDR2) 533/667 MHz 64-bit Wide DDRII (DDR2) Data Channels Memory Expandable up to 2GB (256/ 512/ 1024 MB DDRII Modules) (Note: Do Not Use Other Module Types) Video Controller Intel 945GM Integration Intel® Graphics Media Accelerator 950 (Intel® GMA 950) Dynamic Video Memory Technology DVMT - Supports up to 224MB of Video Memory (dynamically allocated f
Specifications Feature B Specification Interface One Serial Port One Parallel Port One External Monitor Port One Headphone-Out Jack One Microphone-In Jack One Line-In Jack Communication 1GB PCIe Ethernet LAN MDC 56K Fax Modem - V.90 & V.92 Compliant Intel PRO/Wireless 3945ABG PCIe Interface Wireless LAN Module (Optional) 802.11 b/g Wireless LAN Module (Optional) USB (2.0) Bluetooth Module (Factory Option) Power Management Supports ACPI 2.
Specifications Feature Optional Specification Optical Drive Module Options: Combo Drive Module DVD-Dual Drive Module DVD Super Multi Drive Module Intel PRO/Wireless 3945ABG PCIe Interface Wireless LAN Module Touch Panel (Factory Option) USB (2.0) Bluetooth Module (Factory Option) 802.
Specifications B B - 6
