Preface Notice The company reserves the right to revise this publication or to change its contents without notice. Information contained herein is for reference only and does not constitute a commitment on the part of the manufacturer or any subsequent vendor. They assume no responsibility or liability for any errors or inaccuracies that may appear in this publication nor are they in anyway responsible for any loss or damage resulting from the use (or misuse) of this publication.
Preface FCC Statement (Federal Communications Commission) You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Preface FCC RF Radiation Exposure Statement: 1. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. Warning Use only shielded cables to connect I/O devices to this equipment.
Preface IMPORTANT SAFETY INSTRUCTIONS Follow basic safety precautions, including those listed below, to reduce the risk of fire, electric shock, and injury to persons when using any electrical equipment: 1. 2. 3. 4. 5. Do not use this product near water, for example near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool. Avoid using this equipment with a telephone line (other than a cordless type) during an electrical storm.
Preface Instructions for Care and Operation The computer is quite rugged, but it can be damaged. To prevent this, follow these suggestions: 1. Don’t drop it, or expose it to shock. If the computer falls, the case and the components could be damaged. 2. Keep it dry, and don’t overheat it. Keep the computer and power supply away from any kind of heating element. This is an electrical appliance. If water or any other liquid gets into it, the computer could be badly damaged. 3. Avoid interference.
Preface Power Safety The computer has specific power requirements: Power Safety Warning Before you undertake any upgrade procedures, make sure that you have turned off the power, and disconnected all peripherals and cables (including telephone lines). VI • When you want to unplug the power cord, be sure to disconnect it by the plug head, not by its wire. • Make sure the socket and any extension cord(s) you use can support the total current load of all the connected devices.
Preface Cleaning Do not apply cleaner directly to the computer, use a soft clean cloth. Do not use volatile (petroleum distillates) or abrasive cleaners on any part of the computer. Servicing Do not attempt to service the computer yourself. Doing so may violate your warranty and expose you and the computer to electric shock. Refer all servicing to authorized service personnel. Unplug the computer from the power supply.
Preface Ergonomics We designed your Multimedia PC system to be functional as well as attractive. To get most out of it, here are some suggestions on how to position and use the computer: • The top third of the LCD (screen) should be at eye-level or slightly below. • The LCD should be at least 18"/45cm. directly in front of you. • If the screen resolution makes you strain to read, then adjust the resolution to something more comfortable (see “Video Features” on page 1 - 14).
Preface Lighting Proper lighting and comfortable display viewing angle can reduce eye strain and muscle fatigue in your neck and shoulders. • • • • Position the display to avoid glare or reflections from overhead lighting or outside sources of light. Keep the display screen clean and set the brightness and contrast to levels that allow you to see the screen clearly. Position the display directly in front of you at a comfortable viewing distance. Adjust the display-viewing angle to find the best position.
Preface X
Preface Contents Notice .................................................................................I FCC Statement .............................................................II FCC RF Radiation Exposure Statement: ................... III Instructions for Care and Operation ........................... V Power Safety .............................................................. VI Cleaning ....................................................................VII Servicing .............................
Preface Power Management Overview ........................................................................3-1 Turning on the Computer ...............................................3-2 Power Plans ...................................................................3-3 System Power Options ...................................................3-5 Hibernate vs. Shut Down .............................................3-5 Sleep vs. Hibernate ......................................................3-5 Sleep ..........
Preface Revision (Main Menu) ...................................................5-7 Advanced Menu .............................................................5-8 SIO ITE8305E (Advanced Menu) .................................5-8 Installed O/S (Advanced Menu) ....................................5-9 SATA Mode Selection (Advanced Menu) ....................5-9 DFOROM (Robson) Support (Advanced Menu > SATA Mode Selection [AHCI] ...................................5-10 Reset Configuration Data (Advanced Menu) ....
Preface Troubleshooting USB 2.0/1.1 Ports .........................................................A-5 Overview ........................................................................8-1 Basic Hints and Tips ......................................................8-2 Backup and General Maintenance .................................8-3 Viruses ...........................................................................8-4 Upgrading and Adding New Hardware/Software ..........
Preface ExpressCard Slot .......................................................... C-4 Mini-Card Slots ............................................................ C-4 Communication ............................................................. C-4 Power Management ...................................................... C-4 Power ............................................................................ C-4 Environmental Spec ...................................................... C-4 Dimensions & Weight ..
Preface Calibrating the Touch Screen ......................................
Quick Start Guide Chapter 1: Quick Start Guide Overview This Quick Start Guide is a brief introduction to the basic features of your computer, to navigating around the computer and to getting your system started. The remainder of the manual covers the following: • Chapter 2 • Chapter 3 • Chapter 4 • Chapter 5 • Chapter 6 • Chapter 7 • Chapter 8 • Appendix A • Appendix B • Appendix C • Appendix D A guide to using some of the main features of the computer e.g.
1 Quick Start Guide Advanced Users If you are an advanced user you may skip over most of this Quick Start Guide. However you may find it useful to refer to “What to Install” on page 4 - 1, “BIOS Utilities” on page 5 - 1 and “Upgrading The Computer” on page 6 - 1 in the User’s Manual. You may also find the notes marked with a of interest to you. Notes Check the light colored boxes with the mark above to find detailed information about the computer’s features.
Quick Start Guide Not Included Operating Systems (e.g. Windows Vista/Windows XP) and applications (e.g. word processing, spreadsheet and database programs) have their own manuals, so please consult the appropriate manuals. Drivers If you are installing new system software, or are re-configuring your computer for a different system, you will need to install the drivers listed in “Drivers & Utilities” on page 4 - 1.
1 Quick Start Guide System Software Your computer may already come with system software pre-installed. Where this is not the case, or where you are re-configuring your computer for a different system, you will find the following operating systems are supported.
Quick Start Guide System Startup 1. 2. 3. 4. Remove all packing materials, CDs/DVDs and floppy disks etc. Securely attach any peripherals you want to use with the computer to their ports (e.g keyboard and mouse etc.) Attach the AC/DC adapter to the DC-In jack located under the LCD, then plug the AC power cord into an outlet, and connect the AC power cord to the AC/DC adapter. Push the power button at the front of the computer (under the LCD) to turn the computer “on”.
1 Quick Start Guide System Map: Front View 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16.
Quick Start Guide Tilting the LCD Screen It is possible to tilt the LCD screen in order to get the best possible viewing angle of the screen without glare etc. Apply pressure with one hand at the base of the computer, while carefully pushing the LCD screen to tilt it to the appropriate viewing angle. 45° Moving the Computer We strongly recommend using both hands to move the computer. You can use one hand to grip the computer by the stand, and the other to hold the top of the LCD screen.
1 Quick Start Guide Keyboard Options There are two keyboard options for this computer series. These keyboards may include embedded numerical keypads for easy numeric data input and/or function keys/hot keys to allow you to change operational features instantly. Some keyboards may require a driver to access all available functions etc.
Quick Start Guide LED & Hot Key Indicators The LED indicators on the computer display helpful information about the current status of the computer. Icon Color Description Green The computer is On Blinking Green The computer is in Sleep Mode Orange The AC/DC Adapter is Plugged in & the Computer is Powered Off Green System Activity Table 1 - 2 - LED Indicators Visual indicators for brightness and volume are available when the hot key utility is installed (see “Hot Key” on page 4 - 6).
1 Quick Start Guide Figure 1 - 5 Left View Stand S/PDIF-Out Jack Headphone-Out Jack 4. Microphone-In Jack 5. Line-In Jack 6. Mini-IEEE 1394 Port 7. HDMI-Out Port 8. 1 * USB 2.0 Port 9. 7-in-1 Card Reader 10. ExpressCard Slot (see page 2 - 7) System Map: Left View 1. 2. 3. ExpressCard Slot 10 The ExpressCard Slot accepts either ExpressCard/34 or ExpressCard/ 54 formats.
Quick Start Guide System Map: Right View Figure 1 - 6 - Right View 1. 2. Stand Optical Device Drive Bay (for CD/DVD Device - see page 2 - 3) CD Emergency Eject If you need to manually eject a CD/DVD (e.g. due to an unexpected power interruption) you may push the end of a straightened paper clip into the emergency eject hole. Do not use a sharpened pencil or similar object that may break and become lodged in the hole.
1 Quick Start Guide Figure 1 - 7 Rear View 1. 2. 3. 4. 5. Stand Rear Component Cover Vent/Fan Intake Security Lock Slot Carrying Handle Area System Map: Rear View 3 CPU 2 The CPU is not a user serviceable part. Opening this compartment, or accessing the CPU in any way, may violate your warranty. 1 Overheating To prevent your computer from overheating make sure nothing blocks the Vent/Fan Intake while the computer is in use.
Quick Start Guide Windows Vista Start Menu & Control Panel Most of the control panels, utilities and programs within Windows Vista (and most other Windows versions) are accessed from the Start menu. When you install programs and utilities they will be installed on your hard disk drive, and a shortcut will usually be placed in the Start menu and/or the desktop. Right-click the Start menu icon , and then select Properties if you want to customize the appearance of the Start menu.
1 Quick Start Guide Video Features You can switch display devices, and configure display options, from the Display Settings control panel (in Personalization) in Windows Vista as long as the appropriate Intel video driver is installed. For more detailed video information see “Intel Video Driver Controls” on page B - 1. To access Display Settings in Windows Vista: 1. 2. 3. 4. 5. 6. 7. Click Start, and click Control Panel (or point to Settings and click Control Panel).
Quick Start Guide 1 2 4 3 Figure 1 - 9 - Display Properties Desktop Intel Display Mode Description Single Mode One of the connected displays is used as the display device Intel(R) Dual Display Clone Mode Both connected displays output the same view and may be configured independently Extended Desktop Mode Both connected displays are treated as separate devices, and act as a virtual desktop Table 1 - 4 - Display Options Video Features 1 - 15 1
1 Quick Start Guide Power Options The Power Options (Hardware and Sound menu) control panel icon in Windows (see page 1 - 13) allows you to configure power management features for your computer. You can conserve power by means of power plans and configure the options for the power button, sleep button, display and sleep mode from the left menu. Note that the power saver plan may have an affect on computer performance.
Features & Components Chapter 2: Features & Components 2 Overview Read this chapter to learn more about the following main features and components of the computer: • • • • • • Hard Disk Drive Optical (CD/DVD) Device 7-in-1 Card Reader ExpressCard Slot Audio Features Adding a Printer Overview 2 - 1
Features & Components 2 Power Safety Before attempting to access any of the internal components of your computer please ensure that the machine is not connected to the AC power, and that the machine is turned off. Also ensure that all peripheral cables, including phone lines, are disconnected from the computer. Hard Disk Drive The hard disk drive is used to store your data in the computer. The hard disk can be taken out to accommodate other 2.5" serial (SATA) hard disk drives with a height of 9.5 mm.
Features & Components Optical (CD/DVD) Device There is a bay for a 5.25" optical (CD/DVD) device (12.7mm height). The actual device will depend on the module you purchased (see “Storage” on page C - 3). The optical device is usually labeled “Drive D:” and may be used as a boot device if properly set in the BIOS (see “Boot Menu” on page 5 - 14).
Features & Components 2 Handling CDs or DVDs CD Emergency Eject If you need to manually eject a CD (e.g. due to an unexpected power interruption) you may push the end of a straightened paper clip into the emergency eject hole. However please do NOT use a sharpened pencil or similar object that may break and become lodged in the hole. Proper handling of your CDs/DVDs will prevent them from being damaged. Please follow the advice below to make sure that the data stored on your CDs/DVDs can be accessed.
Features & Components DVD Regional Codes 2 To change the DVD regional codes see “Changing DVD Regional Codes” on page 1 - 11.
Features & Components 2 Card Reader Cover Make sure you keep the cover in the card reader when not in use. This will help prevent foreign objects and/or dust getting in to the card reader. Figure 2 - 3 Front View 1. 7-in-1 Card Reader The card reader allows you to use some of the latest digital storage cards. Push the card into the slot and it will appear as a removable device, and can be accessed in the same way as your hard disk (s).
Features & Components ExpressCard Slot The computer is equipped with an ExpressCard/34/54 slot that reads Express Card/ 34 and ExpressCard/54 formats. ExpressCards are the successors to PCMCIA (PC Cards). ExpressCard/54 is used for applications which require a larger interface slot, e.g. CompactFlash card reader. The number denotes the card width; 54mm for the Express Card/54 and 34mm for the ExpressCard/34. Make sure you install the Card Reader driver (see “ExpressCard/Card Reader” on page 4 - 6).
Features & Components 2 Sound Volume Adjustment The sound volume level is set using the volume control within Windows (and the volume function keys on the computer). Click the volume icon in the taskbar to check the setting. Audio Features You can configure the audio options on your computer from the Sound control panel in Windows, or from the Realtek HD Audio Manager icon in the taskbar/ control panel (right-click the taskbar icon to bring up an audio menu).
Features & Components Audio Jacks 2 Note that the system has two sets of audio jacks as well as internal speakers. All the audio jacks cannot function at the same time and are therefore assigned a priority order depending on your audio connections. • Priority 1 = The audio jacks at the front of the computer. Thus the audio jacks at the side of the computer and the internal speakers are disabled (e.
Features & Components 2 Parallel Printer After setting up the printer attach the parallel cable to the printer. Connect the printer’s parallel cable to the Parallel to USB converter, and then plug the converter into the USB port. Turn ON the printer, then turn ON the computer. Windows will identify the printer and either load one of its own drivers or ask you to supply one. Follow the on-screen instructions. Adding a Printer The most commonly used peripheral is a printer.
Power Management Chapter 3: Power Management Overview To conserve power, especially when using the battery, your computer power management conserves power by controlling individual components of the computer (the monitor and hard disk drive) or the whole system.
Power Management 3 Shut Down Note that you should always shut your computer down by choosing the Shut Down command from the Lock Button Menu in Windows Vista. This will help prevent hard disk or system problems. Turning on the Computer To turn the computer on simply press the power button (see “System Startup” on page 1 - 5).
Power Management Power Plans The computer can be configured to conserve power by means of power plans. You can use (or modify) an existing power plan, or create a new one. The settings may be adjusted to set the display to turn off after a specified time, and to send the computer into Sleep after a period of inactivity. Click Change plan settings and then click Change advanced power settings to access further configuration options in Advanced Settings.
Power Management Each Windows power plan will also adjust the processor performance of your machine in order to save power. This is worth bearing in mind if you are experiencing any reduced performance.
Power Management System Power Options You can use the system power options to stop the computer’s operation and restart where you left off. The system features Sleep and Hibernate power saving states. Hibernate vs. Shut Down Hibernate and Shut Down are the same in that the system is off and you need to press the power button to turn it on.
Power Management Sleep 3 Hibernate Mode In Windows Vista SP1 If you are using Windows Vista SP1 with 4GB RAM installed, see page 8 - 9 for information on Hibernate. Sleep uses very little system power, and takes a short time to return to full operation. After an extended period of time in Sleep the computer will save the contents of system memory (e.g. any open documents and applications) to the hard disk and shut the system down.
Power Management Configuring the Power Button The power button may be set to send the computer in to either Sleep or Hibernate. In Sleep, the LED will blink green. In Hibernate the LED will be orange. If only the display is turned off, the LED will remain green. Password Protection It is recommended that you enable a password on wake up in order to protect your data.
Power Management Resuming Operation You can resume operation from power-saving states by pressing the power button, or in some cases pressing the sleep button (see your keyboard documentation).
Drivers & Utilities Chapter 4: Drivers & Utilities This chapter deals with installing the drivers and utilities essential to the operation or improvement of some of the computer’s subsystems. The system takes advantage of some newer hardware components for which the latest versions of most available operating systems haven’t built in drivers and utilities. Thus, some of the system components won’t be auto-configured with an appropriate driver or utility during operating system installation.
Drivers & Utilities Driver Installation Insert the Device Drivers & Utilities + User’s Manual disc and click Install Drivers (button)/Option Drivers (button). 1. 2. 4 3. Check the driver installation order from Table 4 - 1, on page 4 - 3 (the drivers must be installed in this order) which is the same as that listed in the Drivers Installer menu below.
Drivers & Utilities Driver - Windows Vista with Service Pack 1 Page # Chipset Page 4 - 5 Video Page 4 - 5 Audio Page 4 - 5 Modem Page 4 - 5 LAN Page 4 - 5 ExpressCard/Card Reader Page 4 - 6 Hot Key Page 4 - 6 e-SATA Support Page 7 - 24 Wireless LAN Module Page 7 - 6 PC Camera Module Page 7 - 12 Touch Screen Module Page 4 - 7 Intel Turbo Memory Module Page 7 - 24 Manual Driver Installation Click Browse CD (button) in the Drivers Installer application and browse to the executable fil
Drivers & Utilities 4 Updating/Reinstalling Individual Drivers User Account Control (Win Vista) If you wish to update/reinstall individual drivers it may be necessary to uninstall the original driver.To do this go to the Control Panel in the Windows OS and double-click the Programs and Features icon (Programs > Uninstall a program). Click to select the driver (if it is not listed see below) and click Uninstall, and then follow the on screen prompts (it may be necessary to restart the computer).
Drivers & Utilities Driver Installation Procedure Insert the Device Drivers & Utilities + User’s Manual disc and click Install Drivers (button), or Option Drivers (button) to access the Optional driver menu. Chipset 1. Click 1.Install Chipset Driver > Yes. 2. Click Next > Yes > Next > Next. 3. Click Finish to restart the computer. Video 1. Click 2.Install Video Driver > Yes. 2. Click Next > Yes > Next > Next. 3. Click Finish to restart the computer. Audio 1. Click 3.Install Audio Driver > Yes. 2.
Drivers & Utilities ExpressCard/Card Reader 1. Click 6.Install CardReader Driver > Yes. 2. Click Next > Install. 3. Click Finish to complete the installation. 4 Hot Key 1. Click 7.Install Hotkey Driver > Yes. 2. Click Next > Install. 3. Click Finish > Finish to restart your computer. e-SATA Support See “Intel Turbo Memory & Matrix Storage Setup and Driver Installation” on page 7 - 28 for instructions on installing this driver to enable the e-SATA port.
Drivers & Utilities Optional Drivers Bluetooth Module See the pages indicated for the driver installation procedures for any modules included in your purchase option. Insert the Device Drivers & Utilities + User’s Manual disc and click Option Drivers (button) to access the optional driver menu. Note: The operating system is the default setting for Bluetooth control in Windows Vista. See “Bluetooth Module” on page 7 - 2 for configuration instructions.
Drivers & Utilities 4 4 - 8
BIOS Utilities Chapter 5: BIOS Utilities Overview This chapter gives a brief introduction to the computer’s built-in software: Diagnostics: The POST (Power-On Self Test) Configuration: The Setup utility If your computer has never been set up, or you are making important changes to the system (e.g. hard disk setup), then you should review this chapter first and note the original settings found in Setup. Even if you are a beginner, keep a record of the settings you find and any changes you make.
BIOS Utilities The Power-On Self Test (POST) Each time you turn on the computer, the system takes a few seconds to conduct a POST, including a quick test of the on-board RAM (memory). 5 As the POST proceeds, the computer will tell you if there is anything wrong. If there is a problem that prevents the system from booting, it will display a system summary and prompt you to run Setup. If there are no problems, the Setup prompt will disappear and the system will load the operating system.
BIOS Utilities Failing the POST Errors can be detected during the POST. There are two categories, “fatal” and “nonfatal”. Fatal Errors These stop the boot process and usually indicate there is something seriously wrong with your system. Take the computer to your service representative or authorized service center as soon as possible. Non-Fatal Errors This kind of error still allows you to boot.
BIOS Utilities The Setup Program The Setup Utility program tells the system how to configure itself and manage basic features and subsystems (e.g. port configuration). Entering Setup 5 To enter the Setup Utility, turn on the computer and press F2 during the POST. The prompt (Press F2 to Enter Setup) seen on page 5 - 2 is usually present for a few seconds after you turn on the system. If you get a “Keyboard Error”, (usually because you pressed F2 too quickly) just press F2 again.
BIOS Utilities Setup Screens The following pages contain additional advice on portions of the Setup Utility. Setup Menus Along the top of the screen is a menu bar with menu headings. When you select a heading, a new screen appears. Scroll through the features listed on each screen to make changes to Setup Utility. Instructions on how to navigate each screen are in the box along the bottom of the screen.
BIOS Utilities Main Menu Phoenix SecureCore(tm) Setup Utility Figure 5 - 1 Main Main Advanced Security Boot Exit Main Menu Item Specific Help [22:12:05] [05/28/2008] System Time: System Date: SATA Port 1 SATA Port 2 5 [None] [None] System Memory: Extended Memory: 640 KB 1979 MB BIOS Revision: KBC/EC Firmware Revision: ****** ****** F1 Esc Help Exit Select Item Select Menu -/+ Enter , , or selects field.
BIOS Utilities SATA Port 1/2 (Main Menu) Pressing Enter opens the sub-menu to show the configuration of a hard disk or optical device drive on the computer’s SATA Ports. Use the Auto (Type:) setting to have the items configured automatically for you. System/Extended Memory (Main Menu) This item contains information on the system memory, and is not user configurable. The system will auto detect the amount of memory installed.
BIOS Utilities Advanced Menu Phoenix SecureCore(tm) Setup Utility Figure 5 - 2 Main Advanced Advanced Security Boot Exit Advanced Menu Item Specific Help 5 SIO ITE8305E Installed O/S: SATA Mode Selection: DFOROM(Robson) Support: Reset Configuration Data: Boot-time Diagnostic Screen: Legacy OS Boot: Power On Boot Beep: FAN Control: [Vista] [AHCI] [Enabled] [No] [Disabled] [Disabled] [Enabled] [Disabled] These items control the configuration of various National 393 SIO devices.
BIOS Utilities Installed O/S (Advanced Menu) This setting tells the computer what kind of operating system you’re using. Make sure you choose the correct setting for your O/S in order to prevent system problems. Note: If you select the Vista O/S then the SATA Mode Selection menu will become available. If you are installing the Windows XP O/S make sure you have set the appropriate operating system here in order to prevent system problems.
BIOS Utilities SATA Mode & eSata Port 5 The eSATA port only supports hot-swapping if you have selected AHCI mode in SATA Mode Selection, and enabled DFOROM (Robson) Support. DFOROM (Robson) Support (Advanced Menu > SATA Mode Selection [AHCI] This item will only be available if you have selected AHCI in SATA Mode Selection. The option should be enabled if you have included an optional Intel Turbo Memory Module in your purchase configuration, or you want to support eSATA port hot-swapping.
BIOS Utilities Power On Boot Beep (Advanced Menu) Use this menu to enable/disable the single beep sound at the end of the POST. This item is “Disabled” by default. Fan Control (Advanced Menu) This menu item allows you to set the fan cooling behavior under light system activity (if you choose Automatic the system will adjust the fan cooling as appropriate for the system activity).
BIOS Utilities Security Menu Phoenix SecureCore(tm) Setup Utility Security Menu Main Advanced Security Security Boot Exit = 5 Item Specific Help The changes you make here affect the access to the Setup utility itself, and also access to your machine as it boots up after you turn it on. These settings do not affect your machine or network passwords which will be set in your software OS.
BIOS Utilities Set User Password (Security Menu) You can set a password for user mode access to the Setup Utility. This will not affect access to the computer OS, (only the Setup utility) unless you choose to set a Password on Boot (see below). Many menu items in the Setup Utility cannot be modified in user mode. You can only set the user password after you have set the supervisor password.
BIOS Utilities Boot Menu Figure 5 - 4 Phoenix SecureCore(tm) Setup Utility Main Advanced Security Boot Exit Boot Menu Item Specific Help Boot priority order: 1: USB KEY: 2: USB HDD: 3: IDE CD: 4: IDE HDD: 5: PCI BEV: P4-Optiarc CDRWDVD CRX890S 6: USB FDC: 7: USB CDROM: 8: Excluded from boot order: : USB ZIP: : USB LS120: : PCI SCSI: P0-FUJITSU MHY2120BH : PCI BEV: Realtek Boot Agent : Other USB: : PCI: : Legacy 5 F1 Esc Help Exit Select Item Select Menu -/+ Enter Keys used to view o
BIOS Utilities Exit Menu Figure 5 - 5 Phoenix SecureCore(tm) Setup Utility Main Advanced Security Boot Exit Exit Menu Item Specific Help Exit Saving Changes Exit Discarding Changes Load Setup Defaults Discard Changes Save Changes F1 Esc Help Exit Select Item Select Menu Exit System Setup and save your changes to CMOS.
BIOS Utilities 5 5 - 16
Upgrading The Computer Chapter 6: Upgrading The Computer Overview This chapter contains information on upgrading the computer. Follow the steps outlined to make the desired upgrades. If you have any trouble or problems you can contact your service representative for further help.
Upgrading The Computer When Not to Upgrade Power Safety Warning 6 Before you undertake any upgrade procedures, make sure that you have turned off the power, and disconnected all peripherals and cables (including telephone lines). These procedures involve opening the system’s case, adding and sometimes replacing parts.
Upgrading The Computer Removing the Rear Top Cover Before undertaking any upgrade procedure it is necessary to remove the rear top cover to access the components. 1. 2. 3. Turn off the computer and disconnect all cables and peripherals. Carefully place the computer flat with the LCD facing down (make sure you cover the LCD to avoid scratches) so that you may access the rear cover. Remove screws 1 - 4 .
Upgrading The Computer 4. Slide the rear top cover until the arrow is aligned with the unlock icon 5 . Figure 6 - 2 Rear Top Cover Unlock 5 6 5. When the arrow is aligned with the unlock icon you can remove the rear top cover 6 .
Upgrading The Computer Wireless Keyboard & Mouse USB Receiver If your purchase includes an optional Wireless Keyboard & Mouse Kit you can use the USB port located behind the rear top cover to house the USB receiver. 1. 2. 3. Remove the rear cover (see “Removing the Rear Top Cover” on page 6 - 3). Insert the USB receiver 1 into the USB port 2 . Replace the rear top cover and screws.
Upgrading The Computer HDD System Warning 6 New HDD’s are blank. Before you begin make sure: You have backed up any data you want to keep from your old HDD. You have all the CD-ROMs and FDDs required to install your operating system and programs. If you have access to the internet, download the latest application and hardware driver updates for the operating system you plan to install. Copy these to a removable medium.
Upgrading The Computer 3. Firstly slide the hard disk in the direction of arrow 4 , and then slide it in the direction of arrow 5 to remove it. 5 Figure 6 - 6 Hard Disk Assembly Removal 4 6 4. Remove the adhesive hard disk cover 6 . 6 Figure 6 - 7 Hard Disk Cover Removal 5. Reverse the process to install a new hard disk.
Upgrading The Computer Upgrading the System Memory (RAM) The computer has two memory sockets for 200 pin Small Outline Dual In-line (SODIMM) DDRII (DDR2) type memory modules (see “Memory” on page C - 2 for details of supported module types). The total memory size is automatically detected by the POST routine once you turn on your computer. 1. 2. 6 Remove the rear cover (see “Removing the Rear Top Cover” on page 6 - 3). The RAM is located at point 1 .
Upgrading The Computer 3. Gently pull the two release latches on the sides of the memory socket in the direction indicated by the arrows ( 2 & 2 ) in Figure 6 - 9. Contact Warning 4. 5. 6. 2 3 2 3 Be careful not to touch the metal pins on the module’s connecting edge. Even the cleanest hands have oils which can attract particles, and degrade the module’s performance. The RAM module will pop-up, and you can remove it. Pull the latches to release the second module if necessary.
Upgrading The Computer Warranty The CPU is not a user serviceable part. Opening this compartment, or accessing the CPU in any way, may violate your warranty. 6 Upgrading the Processor If you want to upgrade your computer by replacing the existing processor with a faster/new one you will need to contact your customer service representative. We recommend that you do not do this yourself, since if it is done incorrectly you may damage the processor or mainboard.
Modules & Options Chapter 7: Modules & Options Overview This chapter contains information on the following modules, which may come with your computer, depending on the configuration purchased. If you are unsure please contact your service representative.
Modules & Options Bluetooth Module The optional Bluetooth module allows you to connect your computer to Bluetooth enabled devices such as other computers, desktop computers, mobile phones, printers, digital cameras, PDAs, headsets etc. using a short-range radio frequency. The operating system’s Bluetooth Devices control panel is used to configure the Bluetooth settings in Windows Vista, and therefore does not require a driver.
Modules & Options Bluetooth Configuration in Windows Vista Setup your Bluetooth Device so the Computer Can Find it 1. 2. Turn your Bluetooth device (e.g. PDA, mobile phone etc.) on. Make the device discoverable (to do this check your device documentation). To Turn the Bluetooth Module On 1. 2. A Bluetooth icon will appear in the taskbar (see sidebar). You can then do any of the following to access the Bluetooth Devices control panel.
Modules & Options To Add a Bluetooth Device 1. 2. Figure 7 - 2 Add Bluetooth Device Wizard 3. 4. 5. Access the Bluetooth Devices control panel. Click Options (tab), and make sure that Allow Bluetooth devices to connect to this computer check box (Connections) has a tick inside it. Click Devices (tab), and then click Add. The Add Bluetooth Device Wizard will appear. Click to select “My device is set up and ready to be found”, and then click Next. 6. 7. 8.
Modules & Options To Change Settings for the Bluetooth Device 1. 2. Access the Bluetooth Devices control panel. Click on the device you want to change and click Properties to: • • Change the name of the device (click General, type a new name and click OK). Enable/Disable a service (click Services, clear/tick the check box next to the service and click OK). To Make your Computer Discoverable to Bluetooth Devices 1. 2. 3. Access the Bluetooth Devices control panel.
Modules & Options Wireless LAN Module If you have included an Intel® Wi-Fi Link 5100/5300 Series (802.11 a/g/n) WLAN module, or 3rd Party 802.11b/g WLAN module in your purchase option, install the driver as per the procedure overleaf. Make sure you install the drivers in the order indicated in Table 4 - 1, on page 4 - 3.
Modules & Options Intel® Wi-Fi Link 5100/5300 Series (802.11 a/g/n) Driver Installation 1. Insert the Device Drivers & Utilities + User’s Manual disc into the CD/ DVD drive. 2. Click Option Drivers (button). 3. Click 1.Install WLAN Driver > Yes. 4. Click Next > Next. 5. Click the button to accept the license and click Next. 6. Click Next > Next > Finish. Note: The operating system is the default setting for Wireless LAN control in Windows Vista (see overleaf). 7 802.11b/g Driver Installation 1.
Modules & Options Connecting to a Wireless Network Make sure the Wireless LAN module is turned on (see page 7 - 11). 1. Click the taskbar wireless icon , and then click Connect to a network (or rightclick the icon , and then click Connect to a network). Figure 7 - 5 Taskbar Menus Click icon Right-click icon 7 Network and Sharing Center 2. 3. In the Show list, click to choose Wireless from the drop-down menu. A list of currently available networks will appear.
Modules & Options 4. 5. Click a network, and then click Connect. If you do not see a network you want to connect to, click Set up a connection or network (a list of options will appear allowing manual searching, and creating a new network). Figure 7 - 7 Connecting 7 6. Move the cursor over the taskbar icon to see the connection status (see below).
Modules & Options 7. Security Enabled Networks To disconnect from the wireless network you can click the taskbar wireless icon , and then select Connect or disconnect to access the network menu, and click Disconnect (or right-click the icon , and then click Disconnect from). You should try to make sure that any network you are connecting to is a secure network. 7 Click icon Connecting to unsecure networks may allow unauthorized access to your computer, documents, websites and files etc.
Modules & Options Windows Mobility Center The Windows Mobility Center control panel provides an easy point of access for information on battery status, power plans used and wireless device status etc. To access the Windows Mobility Center: 1. 2. 3. Click Start, and click Control Panel (or point to Settings and click Control Panel). Double-click Windows Mobility Center (Mobile PC). Click the button to Turn wireless off/on, or click the icon to access the network menu.
Modules & Options 2.0M PC Camera Screen Refresh 7 The 2.0M PC Camera module supports a frame rate of 12 fps. If you find that the screen refresh rate is subject to lag or stuttering, then reduce the window size, or adjust the Output Size and/or Color Space Compression. To reduce Output Size and/or Color Space Compression run the BisonCap application, click Options and select Video Capture Pin. Adjust the settings from the appropriate pull-down menu.
Modules & Options PC Camera Audio Setup If you wish to capture video & audio with your camera, it is necessary to connect a microphone to either of the microphone ports and then setup the audio recording options in Windows as follows. 1. 2. 3. 4. Click Start, and click Control Panel (or point to Settings and click Control Panel). Click Sound (Hardware and Sound). Click Recording (tab).
Modules & Options Figure 7 - 11 Audio Setup for PC Camera 7 Right-click 7 - 14 PC Camera Module
Modules & Options BisonCap BisonCap is a video viewer for general purpose video viewing and testing, and capturing video files to .avi format. 1. 2. 3. Run the BisonCap program from the Start > Programs/All Programs > BisonCam menu (it is recommended that you set the capture file before the capture process - see Set Capture File below). Go to the Capture menu heading (if you wish to capture audio check “PC Camera Audio Setup” on page 7 - 13) and select Start Capture.
Modules & Options Reducing Video File Size Note that capturing high resolution video files requires a substantial amount of disk space for each file. After recording video, check the video file size (right-click the file and select Properties) and the remaining free space on your hard disk (go to My Computer, right-click the hard disk, and select Properties). If necessary you can remove the recorded video file to a removable medium e.g. CD, DVD or USB Flash drive.
Modules & Options Eliminating Screen Flicker If you find that the video screen in the BisonCap program is flickering, you can try to adjust the setting in the Video Capture Filter options. 1. 2. 3. Run the BisonCap program. Go to Options and scroll down to select Video Capture Filter.... Click either 50Hz or 60Hz under Frequency in Property Page (tab).
Modules & Options Zoom The BisonCap program allows you to zoom the camera in and out. 1. 2. Run the BisonCap program. Go to Zoom and select Zoom Out/Zoom In. Figure 7 - 13 Zoom/Setting Snapshot Folder 7 The Snapshot folder’s default location is on the desktop. Do not move this folder or an error may appear when you try to take a still picture. Taking Still Pictures The BisonCap programs allows you to take still pictures. 1. 2. 3. Run the BisonCap program. Go to Options and select Take Picture.
Modules & Options Touch Screen Module If you have included a Touch Screen module in your purchase option, you should obtain a stylus pen to interact with the computer in the same way you would use a mouse (use a stylus pen to tap/double-tap on-screen buttons etc.). Calibrate the touch screen before using your stylus pen. Make sure you install the driver as indicated below. Touch Screen Utility Installation 1. Insert the Device Drivers & Utilities + User’s Manual disc into the CD/ DVD drive. 2.
Modules & Options Calibrating the Touch Screen 1. 2. Click Start, and click Programs/All Programs and point to Touch Utilities (folder), and then click Touch Configuration program (or double-click the desktop icon ). Click Calibration (button).
Modules & Options 3. Click to choose the number of points in Calibration Precision, and then click Calibrate (button). Figure 7 - 15 Calibration Precision 7 4. Use the stylus pen to touch the center of the cross sign until the OK sign appears in the center of the cross. Figure 7 - 16 Touch On Cross Calibration Points For maximum accuracy, make sure that you use the stylus pen to touch the CENTER of the blinking target symbol when calibrating the touch screen.
Modules & Options 5. When the Test Drawing appears, write on the screen to test the calibration (press the spacebar to clear any drawing, or Esc to exit). 6. 7. Click Close to exit Calibration. Click Touch Settings (button) to adjust any touch setting (mouse) options.
Modules & Options Tablet PC Input Panel When not in use the Tablet PC Input Panel (not available in Windows Vista Home Basic Edition) docks at the side of the screen (and may be docked at either side of the screen at any height) with just a small portion visible. Move the pen over the TIC and then tap it to activate it. The input panel allows you to input text without the use of a keyboard.
Modules & Options e-SATA Port Support 7 Note that the Intel Matrix Storage driver is required to enable the e-SATA port even if you have not included an Intel Turbo Memory module in your purchase configuration. Follow the instructions provided here in order to install the driver.
Modules & Options 6. Insert the Device Drivers & Utilities + User’s Manual disc into the CD/ DVD drive. 7. Click Option Drivers (button). 8. Click 4.Install TM&iMSM Driver > Yes. 9. Click Next > Yes > Next > Next. 10. Click Finish to restart the computer. If you have a 4GB Turbo Memory Module (see below). For Turbo Memory Modules less than 4GB (see overleaf): 1. Run the Intel® Turbo Memory Dashboard from the Programs/All Programs menu (Intel® Turbo Memory) or from the desktop shortcut. 2.
Modules & Options 1. Run the Intel® Turbo Memory Console from the Programs/All Programs menu (Intel® Turbo Memory). 7 Figure 7 - 21 Intel Turbo Memory Console • Windows ReadyBoost - uses flash memory as a hard-drive caching solution.
Troubleshooting Chapter 8: Troubleshooting Overview Should you have any problems with your computer, before consulting your service representative, you may want to try to solve the problem yourself. This chapter lists some common problems and their possible solutions. This can’t anticipate every problem, but you should check here before you panic. If you don’t find the answer in these pages, make sure you have followed the instructions carefully and observed the safety precautions in the preface.
Troubleshooting Basic Hints and Tips Many of the following may seem obvious but they are often the solution to a problem when your computer appears not to be working. • Power - Is the computer actually plugged into a working electrical outlet? If plugged into a power strip, make sure it is actually working. Check the LED Power & Communication Indicators (see “LED & Hot Key Indicators” on page 1 - 9) to see the computer’s power status.
Troubleshooting Backup and General Maintenance • Always backup your important data, and keep copies of your OS and programs safe, but close to hand. Don’t forget to note the serial numbers if you are storing them out of their original cases, e.g. in a CD wallet. • Run maintenance programs on your hard disk and OS as often as you can. You may schedule these programs to run at times when you are not using your computer.
Troubleshooting Viruses • Install an Anti-Virus program and keep the definitions file (the file which tells your program which viruses to look for) up to date. New computer viruses are discovered daily, and some of them may seriously harm your computer and cause you to lose data. Anti-Virus programs are commercially available and the definitions file updates are usually downloadable directly from the internet. • Be careful when opening e-mail from sources you don’t know.
Troubleshooting Upgrading and Adding New Hardware/Software • Do not be tempted to make changes to your Windows Registry unless you are very sure of what you are doing, otherwise you will risk severely damaging your system. • Don’t open your computer or undertake any repair or upgrade work if you are not comfortable with what you are doing. • Read the documentation.
Troubleshooting • Thoroughly check any recent changes you made to your system as these changes may affect one or more system components, or software programs. If possible, go back and undo the change you just made and see if the problem still occurs. • Don’t over complicate things.
Troubleshooting Problems & Possible Solutions Problem Possible Cause - Solution The computer feels too hot. Make sure the computer is properly ventilated and the Vent/Fan intakes are not blocked. If this doesn’t cool it down, put the system into Hibernate mode or turn it off for an hour. Make sure the computer isn’t sitting on a thermal surface (see “Overheating” on page 1 - 12). Make sure you’re using the correct adapter. Nothing screen. The system is in a power saving mode.
Troubleshooting Problem Possible Cause - Solution The compact disc tray will not open when there is a disc in the tray. The compact disc is not correctly placed in the tray. Gently try to remove the disc using the eject hole (see “Loading Discs” on page 2 - 3). The DVD regional codes can no longer be changed. The code has been changed the maximum 5 times. See “DVD Regional Codes” on page 2 - 5/ “DVD Regional Codes” on page D - 2. You forget password.
Troubleshooting Problem Possible Cause - Solution The system “hangs” (a blank screen appears and the OS will not load) at the POST/start up. You have disabled AHCI mode in the BIOS. If you have installed the Windows Vista operating system with AHCI mode enabled (default setting), DO NOT disable AHCI mode (if you wish to disable AHCI mode you will need to reinstall the Windows VIsta OS).
Troubleshooting Problem Possible Cause - Solution No sound can be heard from the internal/external speakers/headphones. You have plugged in headphones or speakers to the audio jacks at the front of the computer. Note that the system has two sets of audio jacks as well as internal speakers. All the audio jacks cannot function at the same time and are therefore assigned a priority order depending on your audio connections. Priority 1 = The audio jacks at the front of the computer.
Interface (Ports & Jacks) Appendix A: Interface (Ports & Jacks) Overview The following chapter will give a quick description of the interface (ports & jacks) which allow your computer to communicate with external devices, connect to the internet etc.
Interface (Ports & Jacks) Computer Ports and Jacks A Item Description Card Reader Port The card reader allows you to use some of the latest digital storage cards. Push the card into the slot and it will appear as a removable device. COM/Serial Ports The COM/serial is a communication interface for data transfer, through which information transfers in or out one bit at a time. This port can be used to connect the computer to devices such as terminals and peripherals.
Interface (Ports & Jacks) Item Description External Monitor (VGA) Port This port allows you to connect an external monitor, or Flat Panel Display, to get dual video or simultaneous display on the LCD and external monitor/FPD (see “Configuring Other Displays from Intel® GMA Driver for Mobile” on page B - 6). HDMI-Out Port The HDMI-Out (High-Definition Multimedia Interface) is an audio/video connector interface for transmitting uncompressed digital streams.
Interface (Ports & Jacks) Item Description Mini-IEEE 1394 Port This allows high-speed connection to various peripheral devices, e.g. external disk drives and digital cameras (see note below). IEEE 1394 The Mini-IEEE 1394 ports only support SELF POWERED IEEE 1394 devices. RJ-11 Phone Jack RJ-45 LAN Jack This port connects to the built-in modem. You may plug the telephone line directly into this RJ-11 telephone connection. Note: Broadband (e.g. ADSL) modems usually connect to the LAN port.
Interface (Ports & Jacks) Item Description USB 2.0/1.1 Ports These USB 2.0 compatible ports (USB 2.0 is fully USB 1.1 compliant) are for low-speed peripherals such as keyboards, mice or scanners, and for high-speed peripherals such as external HDDs, digital video cameras or high-speed scanners etc.
Interface (Ports & Jacks) A A - 6
Intel Video Driver Controls Appendix B: Intel Video Driver Controls The basic settings for configuring the LCD are outlined in “Video Features” on page 1 - 14. DVMT Notes Intel Video Driver Installation Make sure you install all the drivers in the order indicated in Table 4 - 1, on page 4 - 3. Video 1. Insert the Device Drivers & Utilities + User’s Manual disc into the CD/ DVD drive. 1. Click 2.Install Video Driver > Yes. 2. Click Next > Yes > Next > Next. 3. Click Finish to restart the computer.
Intel Video Driver Controls Taskbar Icon The Intel GMA control panel can also be accessed by clicking the icon in the taskbar and selecting Graphics Properties from the menu. Intel Graphics Properties More advanced video configuration options are provided by the Intel(R) Graphics Media Accelerator Driver for mobile control panel. 1. 2. Open the Display Settings control panel (see “Video Features” on page 1 - 14) and click Advanced Settings (button). Click the Intel(R)...
Intel Video Driver Controls You may make changes to the devices, color, schemes, Hot Keys etc. by clicking the appropriate menu item or button. Help Menus Right-click on many of the items in the tabs to bring up the “What’s This?” button. Click the “What’s This?” button to bring up the help menu. Display Selection At least one other display must be attached in order to view multiple Display Selection options.
Intel Video Driver Controls Application.exe You will need to locate the actual application executable (.exe) file, not just the shortcut. To find the application rightclick its shortcut on the desktop click Properties. Click the Shortcut (tab) and see where the executable file is located by clicking the Find Target (button). Note the location and you will then be able to browse to this file.
Intel Video Driver Controls Attaching Other Displays Besides the built-in LCD you can also use an external monitor/flat panel display/TV (TV through HDMI-Out port only), connected to the external monitor port or to the HDMI-Out port (High-Definition Multimedia Interface) as your display device. The following are the display options: 1. 2. The built-in LCD OR an external monitor/flat panel display connected to the external monitor port or HDMI-Out port (Single Display).
Intel Video Driver Controls Configuring Other Displays from Intel® GMA Driver for Mobile Display Selection At least one other display must be attached in order to view multiple Display Selection options. 1. 2. 3. 4. 5. Attach your external display to the external monitor port or HDMI-Out port, and turn it on. Go to the Intel(R) GMA Driver for mobile control panel (see “Intel Graphics Properties” on page B - 2) and click Display Devices. Click to choose the display mode from the Operating Mode menu.
Intel Video Driver Controls HDMI Audio Configuration As HDMI (High-Definition Multimedia Interface) carries both audio and video signals you will need to configure the audio output as per the instructions below. Windows Audio Setup for HDMI 1. 2. 3. 4. 5. 6. Connect a device with HDMI support to the HDMI-Out port. Click Start, and click Control Panel (or point to Settings and click Control Panel). Click Sound (Hardware and Sound). Click Playback (tab), and click to select HDMI Device.
Intel Video Driver Controls HDMI Notes Other Applications If you are using a third party application to play DVDs etc. you will need to consult the application’s documentation to see the appropriate audio configuration (the application must support digital to analog translation). • Connect a device with HDMI support to the HDMI-Out port BEFORE attempting to play audio/video sources through the device.
Intel Video Driver Controls Display Modes Single Display Only one of your attached displays is used. Intel(R) Dual Display Clone (mirrored) This mode will drive multiple displays with the same content. Each device may be configured independently for different resolutions, refresh rates, color quality etc. Use this feature to display the screen through a projector for a presentation.
Intel Video Driver Controls To Enable Intel(R) Dual Display Clone 1. 2. 3. 4. 5. 6. Figure B - 7 Display Devices & Settings B B - 10 Display Modes Attach your external display to the external monitor port or HDMI-Out port, and turn it on. Go to the Intel(R) GMA Driver for mobile control panel (see “Intel Graphics Properties” on page B - 2) and click Display Devices. Click to choose Intel(R) Dual Display Clone (Operating Mode).
Intel Video Driver Controls To Enable Extended Desktop 1. 2. 3. 4. 5. 6. Attach your external display to the external monitor port or HDMI-Out port, and turn it on. Go to the Intel(R) GMA Driver for mobile control panel (see “Intel Graphics Properties” on page B - 2) and click Display Devices. Click to choose Extended Desktop (Operating Mode). Choose which device is to be the Primary Device/Secondary Device from the Display Selection menu. Click Apply, and OK to confirm the settings change.
Intel Video Driver Controls Using Windows Vista to Enable Extended Mode 1. Display Settings Extended Desktop 2. Use the control panel to drag the monitors to match the physical arrangement you wish to use. 3. 4. 5. You can drag any icons or windows across to either display desktop, which makes it possible to have one program visible in one of the displays, and a different program visible in the other display.
Intel Video Driver Controls Using Display Settings to Enable Extended Mode 1. 2. 3. Attach your external display to the external monitor port or HDMI-Out port, and turn it on. Open the Display Settings control panel (see “Video Features” on page 1 - 18). Click the monitor icon (e.g. 2 ), and make sure you have checked “Extend the desktop onto this monitor” and click Apply. Click the appropriate monitor icon (e.g. 2 ) to be able to select the option to extend the desktop on to it.
Intel Video Driver Controls B B - 14
Specifications Appendix C: Specifications Latest Specification Information The specifications listed in this Appendix are correct at the time of going to press. Certain items (particularly processor types/ speeds and CD/DVD device types) may be changed or updated due to the manufacturer's release schedule. Check with your service center for details.
Specifications Feature Processor C Specification Intel® Core™2 Duo Processor (478-pin) Micro-FC-PGA Package, Socket P TDP: 35W T9400/ T9600 45nm (45 Nanometer) Process Technology 6MB On-die L2 Cache & 1066MHz FSB 2.53/ 2.8 GHz Intel® Core™2 Duo Processor (478-pin) Micro-FC-PGA Package, Socket P TDP: 25W P9500 45nm (45 Nanometer) Process Technology 6MB On-die L2 Cache & 1066MHz FSB 2.
Specifications Feature Specification Video Adapter Intel GM45 Integrated Video Intel® Gen 5.0 Integrated Graphics Engine Integrated High Definition Multimedia Interface (HDMI) Supports DirectX10 3D Graphics Engine Accelerator BIOS One 32Mb Flash ROM Storage One Changeable 12.7mm(h) Optical Device (CD/DVD) Type Drive (see “Optional” on page C - 5 for drive options) with SATA (Serial) Interface Changeable 2.5" 9.
Specifications Feature Specification Card Reader Embedded 7-in-1 Card Reader (MS/ MS Pro/ SD/ Mini SD/ MMC/ RS MMC/ MS Duo) Note: MS Duo/ Mini SD/ RS MMC Cards Require a PC Adapter ExpressCard Slot ExpressCard/34/54 Slot Mini-Card Slots One Mini-Card Slot for Wireless LAN Module Communication Built-In 56K MDC Plug & Play Fax/Modem v.90/92 Compliant Built-In Gigabit Ethernet LAN Bluetooth 2.0 + EDR (Enhanced Data Rate) Module (Factory Option) 1.3M or 2.
Specifications Feature Specification Dimensions & Weight 450mm (w) * 312mm (d) * 66.5mm (h) 11kg Optional Combo Drive Module DVD Dual (Super Multi) Drive Module 1.3M or 2.0M Pixel USB PC Camera Module (Factory Option) Wireless LAN Module: Intel® WiFi Link 5300 Series (3*3 - 802.11a/g/n) Wireless LAN Mini-Card Module (Option) Intel® WiFi Link 5100 Series (1*2 - 802.11a/g/n) Wireless LAN Mini-Card Module (Option) Bluetooth 2.0 + EDR (Enhanced Data Rate) Module (Factory Option) 3rd Party 802.
Specifications C
Windows XP Information Appendix D: Windows XP Information This Appendix contains information (including control panel information, driver installation etc.) for users of the Windows XP OS.
Windows XP Information DVD Regional Codes Changing DVD Regional Codes Go to the Control Panel and double-click System > Hardware (tab), click Device Manager, then click the + next to DVD/CD-ROM drives. Double-click on the DVD-ROM device to bring up the Properties dialogue box, and select the DVD Region (tab) to bring up the control panel to allow you to adjust the regional code. DVD region detection is device dependent, not OS-dependent. You can select your module’s region code 5 times.
Windows XP Information Windows XP Start Menu & Control Panel Most of the control panels, utilities and programs within Windows XP (and most other Windows versions) are accessed from the Start menu. When you install programs and utilities they will be installed on your hard disk drive, and a shortcut will usually be placed in the Start menu and/or the desktop. You can customize the look of the Start menu by right-clicking the Start menu and selecting Properties from the menu.
Windows XP Information Audio Features You can configure the audio options on your computer from the Sounds and Audio Devices Windows control panel, or from the Realtek HD Audio Manager icon in the taskbar/control panel (this will bring up the Realtek Audio Configuration menus). Sound Volume Adjustment How high the sound volume can be set depends on the setting of the volume control within Windows (and the volume control function keys on the computer).
Windows XP Information Audio Jacks Note that the system has two sets of audio jacks as well as internal speakers. All the audio jacks cannot function at the same time and are therefore assigned a priority order depending on your audio connections. • Priority 1 = The audio jacks at the front of the computer. Thus the audio jacks at the side of the computer and the internal speakers are disabled (e.
Windows XP Information Video Features You can switch display devices, and configure display options, from the Display Properties control panel in Windows as long as the appropriate video driver is installed. To access Display Properties in Windows: 1. 2. 3. 4. 5. 6. 7. 8. 9. Click Start, point to Settings and click Control Panel (or just click Control Panel). Double-click Display (icon) - In the Appearances and Themes category. Click Settings (tab) in the Display Properties dialog box.
Windows XP Information Display & Graphics Properties Taskbar Icon You can also access the controller properties from the taskbar. Click on the icon to bring up the menu and scroll to Graphics Properties. If you cannot see the tray icon go to the Intel(R) Graphics Media Accelerator Driver for Mobile tab and click the “Show Tray Icon” tickbox. Alternatively right-click the desktop and select Graphics Options > Tray Icon > Enable.
Windows XP Information You may make changes to the devices, color, schemes, Hot Keys etc. by clicking the appropriate menu item or button. Help Menus Right-click on many of the items in the tabs to bring up the “What’s This?” button. Click the “What’s This?” button to bring up the help menu.
Windows XP Information Display Devices & Options Besides the built-in LCD, you can also use an external VGA monitor (CRT) or external Flat Panel Display as your display device. A VGA monitor/Flat Panel Display connects to the external monitor port. The following display modes are available.
Windows XP Information Display Selection At least one other display must be attached in order to view multiple Display Selection options. Attaching Other Displays If you prefer to use a monitor or flat panel display, connect it to the external monitor port on the left of the computer. 1. 2. 3. 4. Attach your external display to the external monitor port, and turn it on. Go to the Intel(R) GMA Driver for mobile control panel and click Display Devices.
Windows XP Information To Enable Intel(R) Dual Display Clone (Intel GMA) 1. 2. 3. 4. 5. Attach your external display to the external monitor port, and turn it on. Go to the Intel(R) GMA Driver for mobile control panel and click Display Devices. Click to choose Intel(R) Dual Display Clone (Operating Mode). Click Apply, and OK to confirm the settings change. Click Display Settings to adjust the settings for the attached devices.
Windows XP Information To Enable Extended Desktop (Intel GMA) 1. 2. 3. 4. 5. Attach your external display to the external monitor port, and turn it on. Go to the Intel(R) GMA Driver for mobile control panel and click Display Devices. Click to choose Extended Desktop (Operating Mode). Click Apply, and OK to confirm the settings change. Click Display Settings to adjust the settings for the attached devices. Click the appropriate monitor icon and drag it to match the physical arrangement you wish to use (e.
Windows XP Information To Enable Extended Desktop (Windows Display Properties) 1. 2. 3. 4. 5. Attach your external monitor to the external monitor port, and turn it on. Click Start, point to Settings (or click Control Panel) and click Control Panel (if you are in Category View choose Appearance and Themes). Double-click Display (icon). In the Display Properties dialog box, click Settings (tab). Click the monitor icon (e.g. 2 ), and make sure you have checked “Extend my Windows desktop onto this monitor.
Windows XP Information HDMI Audio Configuration As HDMI (High-Definition Multimedia Interface) carries both audio and video signals you will need to configure the audio output as per the instructions below. Windows Audio Setup for HDMI 1. Connect a device with HDMI support to the HDMI-Out port. 2. Go to the Start menu and point to Settings (or just click Control Panel) and click Control Panel, then double-click the Sounds & Audio Devices icon (Sounds, Speech, and Audio Devices in Category View). 3.
Windows XP Information HDMI Notes • Connect a device with HDMI support to the HDMI-Out port BEFORE attempting to play audio/video sources through the device. • If you disconnect the HDMI cable the default audio playback device will not revert to speakers until the computer is restarted (if you do not wish to restart the computer then go to the Sound control panel and select Speakers as the default audio playback device). HDMI Video Configuration 1. 2. 3. 4.
Windows XP Information Shutdown Note that you should always shut your computer down by choosing the Shut Down/ Turn Off Computer command from the Start menu in Windows. This will help prevent hard disk or system problems. Power Management The computer uses the ACPI power management system to conserve power by controlling individual components of the computer (the monitor and hard disk drive) or the whole system. Using some form of power management greatly increases the life span of the LCD.
Windows XP Information Power Schemes You can set your computer to conserve power through individual components by means of Power Schemes. You can also adjust the settings for each scheme to set the monitor to turn off after a specified time, and the computer's hard disk motor to turn off if the hard disk drive has not been accessed for a specified period of time (if the system reads or writes data, the hard disk motor will be turned back on).
Windows XP Information Power Button as Standby or Hibernate Button Fully ACPI-compliant operating systems, (such as Windows XP) allow you to use the OS’s “Power Options” control panel to set the power button to send the system into Standby or Hibernate mode (see your OS’s documentation, or “Configuring the Power Button” on page D - 20 for details). System Power Options You can use the system power options to stop the computer’s operation and restart where you left off.
Windows XP Information Standby Standby saves the least amount of power, but takes the shortest time to return to full operation. During Standby the hard disk is turned off, and the CPU is made to idle at its slowest speed. All open applications are retained in memory. When you are not using your computer for a certain length of time, which you specify in the operating system, it will enter Standby mode to save power.
Windows XP Information Configuring the Power Button The power button may be set to send the computer in to either Standby or Hibernate mode. In Standby mode, the Power LED will blink green. In Hibernate the LED will be orange. If the only the display is turned off, the LED will remain green.
Windows XP Information Driver Installation Insert the Device Drivers & Utilities + User’s Manual CD-ROM, click Install Drivers/Option Drivers (button) and then click the appropriate driver name from the Drivers Installer menu. Follow the instructions to install the driver. Alternatively click Start, navigate (Browse..) to the executable file and then follow the manual setup instructions. 1. 2. 3.
Windows XP Information Updating/Reinstalling Individual Drivers WinXP SP2 Driver Page # Chipset Page D - 23 Video Page D - 23 Audio Page D - 23 Modem Page D - 24 LAN Page D - 24 CardReader Page D - 24 Hot Key Page D - 24 Wireless LAN Module Page D - 25 PC Camera Module Page D - 35 Touch Screen Module Page D - 41 Table 5 - Driver Installation D D - 22 Driver Installation If you wish to update/reinstall individual drivers it may be necessary to uninstall the original driver.
Windows XP Information Driver Installation Procedure Windows XP Service Pack 2 Make sure you install Windows XP Service Pack 2 (or a Windows XP version which includes Service Pack 2) before installing any drivers. Service Pack 2 includes support for USB 2.0. If you have upgraded the system by installing Service Pack 2 (i.e. your Windows XP version does not include Service Pack 2) then follow these instructions: 1.Click Start (menu), point to Settings and click Control Panel (or click Control Panel). 2.
Windows XP Information Modem 1. Click 4.Install Modem Driver > Yes. 2. Click OK. 3. The modem is ready for dial-up configuration. Modem Country Selection Be sure to check if the modem country selection is appropriate for you (Control Panel > Phone and Modem Options). LAN 1. Click 5.Install LAN Driver > Yes. 2. Click Next. 3. Click Install > Finish. 4. The network settings can now be configured. D D - 24 Driver Installation CardReader 1. Click 6.Install CardReader Driver > Yes. 2.
Windows XP Information Optional Drivers Bluetooth Module See the pages indicated for the driver installation procedures for any modules included in your purchase option. Insert the Device Drivers & Utilities + User’s Manual disc and click Option Drivers (button) to access the optional driver menu. Note: The operating system is the default setting for Bluetooth control in WindowsXP, and does not require a driver. See “Bluetooth Module” on page D - 26 for configuration instructions.
Windows XP Information Bluetooth Module The operating system’s Bluetooth Devices control panel is used to configure the Bluetooth settings in Windows XP, and therefore does not require a driver.. Bluetooth Data Transfer Note that transferring data between the computer and a Bluetooth enabled device is supported in one direction only (simultaneous data transfer is not supported).
Windows XP Information Bluetooth Local Area Connection Icon If you want to display the Local Area Connection icon for the Bluetooth connection in the taskbar, set it up as follows: 1. 2. 3. 4. Access the Network Connections control panel in Windows (Start > Settings > Network Connections OR Start > Connect To > Show all Connections) or by clicking the taskbar icon . Right-click the Bluetooth connection icon, and select Properties.
Windows XP Information Bluetooth Configuration in Windows XP Bluetooth Taskbar Icon If you cannot see the Bluetooth icon in the taskbar, access the Bluetooth Devices control panel. Click Options (tab), and make sure that Show Bluetooth icon in the notification area check box has a tick inside it. Setup your Bluetooth Device so the Computer Can Find it 1. Turn your Bluetooth device (e.g. PDA, mobile phone etc.) on. 2. Make the device discoverable (to do this check your device documentation).
Windows XP Information To Add a Bluetooth Device 1. 2. 3. 4. 5. Access the Bluetooth Devices control panel. Click Options (tab), and make sure that Allow Bluetooth devices to connect to this computer check box (Connections) has a tick inside it. Click Devices (tab), and then click Add. The Add Bluetooth Device Wizard will appear. Click to select “My device is set up and ready to be found”, and then click Next. Figure D - 19 Add Bluetooth Device Wizard Passkey Options 6. 7. 8.
Windows XP Information To Change Settings for the Bluetooth Device 1. Access the Bluetooth Devices control panel. 2. Click on the device you want to change and click Properties to: • • Change the name of the device (click General, type a new name and click OK). Enable/Disable a service (click Services, clear/tick the check box next to the service and click OK). To Make your Computer Discoverable to Bluetooth Devices 1. Access the Bluetooth Devices control panel. 2.
Windows XP Information Wireless LAN Module If you have included an Intel® Wi-Fi Link 5100/5300 Series (802.11 a/g/n) WLAN or 3rd Party 802.11 b/g WLAN module in your purchase option, install the driver as outlined in the following pages. Download Prerequisite Files for Intel WLAN Before beginning the Intel® Wi-Fi Link 5100/5300 Series driver installation process for Windows XP it is necessary to make sure you have a working internet connection.
Windows XP Information D Intel WLAN Driver Installation 1. Insert the Device Drivers & Utilities + User’s Manual disc into the CD/DVD drive. 2. Option Drivers (button). 3. Click 1.Install WLAN Driver > Yes. 4. Click Next > Next to link to the required prerequisites on the internet. 5. Click Download (button) to download the Windows Installer executable (.exe) file to the computer’s hard disk. 6.
Windows XP Information 18. Make sure that the WiFi On button is selected.
Windows XP Information Network Connection Use the Windows Network Connections control panel to access available wireless networks (Start > Settings > Network Connections or Start > Connect To > Show all Connections). 802.11b/g WLAN Driver Installation 1. Insert the Device Drivers & Utilities + User’s Manual disc into the CD/DVD drive. 2. Option Drivers (button). 3. Click 1.Install WLAN Driver > Yes. 4. Choose the language you prefer and click Next. 5. Click Next > Install. 6.
Windows XP Information PC Camera Module There PC Camera module uses the BisonCap application to capture video files. Taking Still Pictures PC Camera Driver Installation 1. Insert the Device Drivers & Utilities + User’s Manual disc into the CD/ DVD drive. 2. Click Option Drivers (button). 3. Click 2.Install Camera Driver > Yes. 4. Choose the language you prefer and click Next. 5. Click Next > Finish to restart the computer. 6.
Windows XP Information PC Camera Audio Setup If you wish to capture video & audio with your camera, it is necessary to setup the audio recording options in Windows. 1. Go to the Start menu and point to Settings (or just click Control Panel) and click Control Panel, then doubleclick the Sounds & Audio Devices icon (Sounds, Speech, and Audio Devices in Category View). 2. Click Advanced in the Volume > Device volume tab. 3. Click Options and scroll down and click Properties. 4.
Windows XP Information BisonCap BisonCap is a video viewers for general purpose video viewing and testing, and for capturing video files to .avi format. 1. 2. 3. Run the BisonCap application from the Start > Programs/All Programs > BisonCam menu (it is recommended that you set the capture file before the capture process - see Set Capture File below). Go to the Capture menu heading (if you wish to capture audio check “PC Camera Audio Setup” on page D - 36) and select Start Capture.
Windows XP Information Reducing Video File Size Note that capturing high resolution video files requires a substantial amount of disk space for each file. After recording video, check the video file size (right-click the file and select Properties) and the remaining free space on your hard disk (go to My Computer, right-click the hard disk, and select Properties) If necessary you can remove the recorded video file to a removable medium e.g. CD, DVD or USB Flash drive.
Windows XP Information Eliminating Screen Flicker If you find that the video screen in the BisonCap program is flickering, you can try to adjust the setting in the Video Capture Filter options. 1. 2. 3. Run the BisonCap program. Go to Options and scroll down to select Video Capture Filter.... Click either 50Hz or 60Hz under Frequency in Property Page (tab).
Windows XP Information Zoom The BisonCap program allows you to zoom the camera in and out. Figure D - 25 1. Run the BisonCap program. 2. Go to Zoom and select Zoom Out/Zoom In. 3. Go to Options and scroll down to select Setting (Use the slider to adjust the zoom level, and click OK to save the setting). Zoom/Setting Snapshot Folder The Snapshot folder’s default location is on the desktop. Do not move this folder or an error may appear when you try to take a still picture.
Windows XP Information Touch Screen Module If you have included a Touch Screen module in your purchase option, you should obtain a stylus pen to interact with the computer in the same way you would use a mouse (use a stylus pen to tap/double-tap on-screen buttons etc.). Calibrate the touch screen before using your stylus pen. Make sure you install the driver as indicated below. Touch Screen Utility Installation 1. Insert the Device Drivers & Utilities + User’s Manual disc into the CD/ DVD drive. 2.
Windows XP Information Calibrating the Touch Screen 1. Click Start, and click Programs/All Programs and point to Touch Utilities (folder), and then click Touch Configuration program (or double-click the desktop icon ). 2. Click Calibration (button).
Windows XP Information 3. Click to choose the number of points in Calibration Precision, and then click Calibrate (button). Figure D - 27 Calibration Precision 4. Use the stylus pen to touch the center of the cross sign until the OK sign appears in the center of the cross. Figure D - 28 Touch On Cross Calibration Points For maximum accuracy, make sure that you use the stylus pen to touch the CENTER of the blinking target symbol when calibrating the touch screen.
Windows XP Information 5. When the Test Drawing appears, write on the screen to test the calibration (press the spacebar to clear any drawing, or Esc to exit). Figure D - 29 Test Drawing 6. Click Close to exit Calibration. 7. Click Touch Settings (button) to adjust any touch setting (mouse) options.
