Preface Notice The company reserves the right to revise this publication or to change its contents without notice. Information contained herein is for reference only and does not constitute a commitment on the part of the manufacturer or any subsequent vendor. They assume no responsibility or liability for any errors or inaccuracies that may appear in this publication nor are they in anyway responsible for any loss or damage resulting from the use (or misuse) of this publication.
Preface FCC Statement (Federal Communications Commission) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Preface IMPORTANT SAFETY INSTRUCTIONS Follow basic safety precautions, including those listed below, to reduce the risk of fire, electric shock, and injury to persons when using any electrical equipment: 1. 2. 3. 4. 5. Do not use this product near water, for example near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool. Avoid using this equipment with a telephone line (other than a cordless type) during an electrical storm.
Preface Instructions for Care and Operation The notebook computer is quite rugged, but it can be damaged. To prevent this, follow these suggestions: 1. Don’t drop it, or expose it to shock. If the computer falls, the case and the components could be damaged. Do not expose the computer to any shock or vibration. 2. Do not place anything heavy on the computer. Keep it dry, and don’t overheat it. Keep the computer and power supply away from any kind of heating element. This is an electrical appliance.
Preface 3. Avoid interference. Keep the computer away from high capacity transformers, electric motors, and other strong magnetic fields. These can hinder proper performance and damage your data. 4. Follow the proper working procedures for the computer. Shut the computer down properly and don’t forget to save your work. Remember to periodically save your data as data may be lost if the battery is depleted. Do not turn off the power until you properly shut down all programs. 5.
Preface Power Safety The computer has specific power requirements: Power Safety Warning Before you undertake any upgrade procedures, make sure that you have turned off the power, and disconnected all peripherals and cables (including telephone lines). It is advisable to also remove your battery in order to prevent accidentally turning the machine on. • Only use a power adapter approved for use with this computer.
Preface Battery Precautions • Only use batteries designed for this computer. The wrong battery type may explode, leak or damage the computer. • Do not remove any batteries from the computer while it is powered on. • Do not continue to use a battery that has been dropped, or that appears damaged (e.g. bent or twisted) in any way. Even if the computer continues to work with a damaged battery in place, it may cause circuit damage, which may possibly result in fire.
Preface Cleaning Do not apply cleaner directly to the computer; use a soft clean cloth. Do not use volatile (petroleum distillates) or abrasive cleaners on any part of the computer. Servicing Do not attempt to service the computer yourself. Doing so may violate your warranty and expose you and the computer to electric shock. Refer all servicing to authorized service personnel. Unplug the computer from the power supply.
Preface Travel Considerations Packing As you get ready for your trip, run through this list to make sure the system is ready to go: 1. 2. 3. 4. 5. 6. 7. 8. Check that the battery pack and any spares are fully charged. Power off the computer and peripherals. Close the display panel and make sure it’s latched. Disconnect the AC/DC adapter and cables. Stow them in the carrying bag. The AC/DC adapter uses voltages from 100 to 240 volts so you won’t need a second voltage adapter.
Preface On the Road In addition to the general safety and maintenance suggestions in this preface, and Chapter 8: Troubleshooting, keep these points in mind: Hand-carry the notebook - For security, don’t let it out of your sight. In some areas, computer theft is very common. Don’t check it with “normal” luggage. Baggage handlers may not be sufficiently careful. Avoid knocking the computer against hard objects.
Preface Developing Good Work Habits Developing good work habits is important if you need to work in front of the computer for long periods of time. Improper work habits can result in discomfort or serious injury from repetitive strain to your hands, wrists or other joints. The following are some tips to reduce the strain: • Adjust the height of the chair and/or desk so that the keyboard is at or slightly below the level of your elbow. Keep your forearms, wrists, and hands in a relaxed position.
Preface Lighting Proper lighting and comfortable display viewing angle can reduce eye strain and muscle fatigue in your neck and shoulders. • Position the display to avoid glare or reflections from overhead lighting or outside sources of light. • Keep the display screen clean and set the brightness and contrast to levels that allow you to see the screen clearly. • Position the display directly in front of you at a comfortable viewing distance. • Adjust the display-viewing angle to find the best position.
Preface Contents Notice ...........................................................................I FCC Statement .......................................................II Instructions for Care and Operation ..................... IV Power Safety ........................................................ VI Battery Precautions .............................................VII Cleaning ............................................................ VIII Servicing ..................................................
Preface Auto Mail Checker ...................................................2-8 Application Ap-Key ...............................................2-10 TouchPad and Buttons/Mouse ...............................2-11 Configuring the TouchPad and Buttons ..............2-11 Audio Features .......................................................2-12 Adding a Printer .....................................................2-13 USB Printer .........................................................
Preface Module Drivers ....................................................4-11 Wireless LAN .....................................................4-11 Bluetooth .............................................................4-11 PC Camera ..........................................................4-11 TV Tuner Options ...............................................4-11 BIOS Utilities Overview ..................................................................5-1 The Power-On Self Test (POST) ..................
Preface Intel PRO/Wireless Mini-PCI WLAN Module ........7-2 Intel WLAN Driver Installation ............................7-3 Bluetooth Module .....................................................7-4 Bluetooth Driver Installation ................................7-4 Bluetooth Audio Setup ..........................................7-6 PC Camera Module ..................................................7-8 Sertek PC Camera Driver Installation (WinXP) ...7-9 PC Camera Audio Setup ....................................
Preface ATI Video Driver Controls ATI Video Driver Installation ................................. B-1 ATI Mobility Radeon Properties ............................. B-2 Display Devices ....................................................... B-4 Attaching Other Displays ........................................ B-5 Display Modes ......................................................... B-6 Clone Mode ........................................................... B-7 Enabling TV Display ...........................
Preface XVIII
Quick Start Guide Chapter 1: Quick Start Guide Overview This Quick Start Guide is a brief introduction to the basic features of your computer, to navigating around the computer and to getting your system started. The remainder of the manual covers the following: • Chapter 2 A guide to using some of the main features of the computer e.g. the storage devices (hard disk, optical device, 4-in-1 card reader, PC Card), Auto Mail Checker, Touch Pad & Mouse, Audio Features & Printer.
1 Quick Start Guide Model Differences This notebook series includes two different model types. The models differ slightly in design style including the LCD type, and AC/DC adapter. See Figure 1 - 1 below and Table 1 - 1, on page 1 - 3 for an outline of the model differences (Model B includes two different design types).
Quick Start Guide Feature Model A Model B Pentium M & Celeron M Processor Options Pentium M Processor Options Only Design Types 1 * Design Type 2 * Design Types LCD Type 15.4" WXGA (1440*900) Flat Panel TFT OR 15.4" WSXGA+ (1680*1050) Flat Panel TFT OR 15.4" WUXGA (1920*1200) Flat Panel TFT 17.0" WXGA (1440*900) Flat Panel TFT OR 17.0" WSXGA+ (1680*1050) Flat Panel TFT OR 17.
1 Quick Start Guide Advanced Users If you are an advanced user you may skip over most of this Quick Start Guide. However you may find it useful to refer to “What to Install” on page 4 - 1, “BIOS Utilities” on page 5 - 1 and “Upgrading The Computer” on page 6 - 1 in the User’s Manual. You may also find the notes marked with a of interest to you.
Quick Start Guide Not Included Operating Systems (e.g. Windows XP) and applications (e.g. word processing, spreadsheet and database programs) have their own manuals, so please consult the appropriate manuals. System Software Your computer may already come with system software pre-installed.
1 Quick Start Guide System Startup 1. 2. 3. 4. 5. 6. 7. 8. Remove all packing materials. Place the computer on a stable surface. Securely attach any peripherals you want to use with the notebook (e.g. keyboard and mouse) to their ports. Attach the AC/DC adapter to the DC-In jack at the rear of the computer, then plug the AC power cord into an outlet, and connect the AC power cord to the AC/DC adapter.
Quick Start Guide System Map: Model A - Front View with LCD Panel Open Wireless Device Operation Aboard Aircraft 1. 2. 3. 4. 5. 6. 7. 8. 9. 2 The use of any portable electronic transmission devices (e.g. WLAN or Bluetooth) aboard aircraft is usually prohibited. Make sure any wireless modules are OFF if you are using the computer aboard aircraft.
1 Quick Start Guide System Map: Model B - Front View with LCD Panel Open Figure 1 - 3 Front View - LCD Panel Open 1. 2. 3. 4. 5. 6. 7. 8. 9. 1 Wireless Device Operation Aboard Aircraft Optional Built-In PC Camera LCD Ap-Key Buttons Power Button Keyboard TouchPad and Buttons Audio "DJ" Controls Built-In Microphone Audio "DJ" LED Display Panel (Including LED Indicators) 2 3 The use of any portable electronic transmission devices (e.g. WLAN or Bluetooth) aboard aircraft is usually prohibited.
Quick Start Guide LED Indicators Icon The LED indicators on the computer display helpful information about the current status of the computer.
1 Quick Start Guide Ap-Key Buttons & Keyboard These buttons give instant access to the default Internet browser and e-mail program, and to a user-defined application, with one quick button press. To use the “user-defined application Ap-Key Button”, you must install the driver (see “AP-Key Buttons” on page 4 9). See “Application Ap-Key” on page 2 - 10 for configuration instructions.
Quick Start Guide Function Keys To use the function keys, press and hold the Fn key, then press the appropriate function key (F3 - F12 etc.).
1 Quick Start Guide System Map: Front View (Audio "DJ") 1 2 3 4 5 10 11 6 12 7 8 9 13 Figure 1 - 5 - Front View (Audio "DJ") 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13.
Quick Start Guide Audio "DJ" CD Player The built-in standalone audio CD player gives direct hardware control for audio CDs/DVDs when the computer is shut down, but has a working power source. 1. Make sure that the computer is shut down (i.e. the operating system is not running) but you have a working power source (either battery or AC Power). 2. Press the Audio "DJ" power button. 3.
1 Quick Start Guide System Map: Rear View Rear View - Model A 1 2 3 5 4 7 8 6 9 10 11 Rear View - Model B 1 2 3 4 Figure 1 - 6 - Rear View 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. Vent/Fan Intake/Outlet S/PDIF-Out Jack Line-In Jack 2 * USB 2.
Quick Start Guide System Map: Right View Right View - Model A 4 1 2 3 5 6 8 7 Right View - Model B 4 1 2 3 5 8 6 Figure 1 - 7 - Right View Mini-IEEE 1394a Port Both Mini-IEEE 1394a ports only support SELF POWERED IEEE 1394a devices. 1. 2. 3. 4. Headphone-Out Jack Microphone-In Jack 4-in-1 Card Reader PC Card Slot 5. 6. 7. 8. Mini-IEEE 1394a Port 2 * USB 2.
1 Quick Start Guide System Map: Left View Figure 1 - 8 - Left View 1. 2. 3. Security Lock Slot Speaker Optional Device Drive Bay (for CD/DVD Device - see page 2 - 3, or 2nd PATA Hard Disk, or 2nd Battery) Left View - Model A 3 2 Left View - Model B 2 3 1 CD/DVD Emergency Eject Changing DVD Regional Codes If you need to manually eject a CD/DVD (e.g. due to an unexpected power interruption) you may push the end of a straightened paper clip into the emergency eject hole.
Quick Start Guide System Map: Bottom View Model A Model B 2 3 1 3 1 1 1 6 4 4 5 4 7 Battery Information Always completely discharge, then fully charge, a new battery before using it. Completely discharge and charge the battery at least once every 30 days or after about 20 partial discharges. See “Battery Information” on page 3 - 9 for full instructions. 7 4 Figure 1 - 9 - Bottom View 1. 2. 3. 4. 5. 6. 7.
1 Quick Start Guide Windows XP Start Menu & Control Panel Most of the control panels, utilities and programs within Windows XP (and most other Windows versions) are accessed from the Start menu. When you install programs and utilities they will be installed on your hard disk drive, and a shortcut will usually be placed in the Start menu and/or the desktop. You can customize the look of the Start menu by right-clicking the Start menu and selecting Properties from the menu.
Quick Start Guide Video Features This computer features Two different PCI Express video cards, depending on the model purchased (see “Video Card Options” on page C - 3). Model A computers feature an ATI Mobility Radeon X700 (M26) video card with 128/256MB DDR video RAM on board; Model B computers feature either an ATI Mobility Radeon X700 (M26) video card with 128MB DDR video RAM on board, or an ATI Mobility Radeon X800 XT (M28 PRO) video card.
1 Quick Start Guide 2 1 3 Figure 1 - 11 - Display Properties Desktop ATI Mobility Radeon Properties The pictures used in Figure 1 - 11 are taken from the ATI Mobility Radeon X700 properties tabs. If your purchase option includes the ATI Mobility Radeon X800 XT video card, then the properties tabs may appear slightly different.
Quick Start Guide Display Devices & Options Besides the built-in LCD, you can also use an external VGA monitor (CRT)/external Flat Panel Display or TV as your display device. A VGA monitor/Flat Panel Display connects to the DVI-Out port, a TV to the SVideo-Out jack. The following display modes are available (see “ATI Video Driver Controls” on page B - 1 for full details).
1 Quick Start Guide Power Management Features The Power Options control panel icon in Windows (see page 1 - 18) allows you to configure power management features for your computer. You may conserve power through individual components such as the monitor or hard disk (by means of Power Schemes), or you may use either Standby or Hibernate mode to conserve power throughout the system (enable Hibernate support from the control panel as pictured in Figure 1 - 12).
Features & Components Chapter 2: Features & Components 2 Overview Read this chapter to learn more about the following main features and components of the computer: • • • • • • • • • Hard Disk Drive Optical (CD/DVD) Device 4-in-1 Card Reader PC Card Slot Auto Mail Checker Application Ap-Key TouchPad and Buttons/Mouse Audio Features Adding a Printer Overview 2 - 1
Features & Components 2 Power Safety Before attempting to access any of the internal components of your computer please ensure that the machine is not connected to the AC power, and that the machine is turned off. Also ensure that all peripheral cables, including phone lines, are disconnected from the computer. Figure 2 - 1 Hard Disk Location 2 - 2 Hard Disk Drive Hard Disk Drive The hard disk drive is used to store your data in the computer. The hard disk can be taken out to accommodate other 2.
Features & Components Optical (CD/DVD) Device There is a bay for a 5.25" optical (CD/DVD) device (12.7mm height). The actual device will depend on the module you purchased (see “Storage” on page C - 4). The optical device is usually labeled “Drive D:” and may be used as a boot device if properly set in the BIOS (see “Boot Menu” on page 5 - 12).
Features & Components 2 CD Emergency Eject If you need to manually eject a CD (e.g. due to an unexpected power interruption) you may push the end of a straightened paper clip into the emergency eject hole. However please do NOT use a sharpened pencil or similar object that may break and become lodged in the hole. Handling CDs or DVDs Proper handling of your CDs/DVDs will prevent them from being damaged. Please follow the advice below to make sure that the data stored on your CDs/ DVDs can be accessed.
Features & Components DVD Regional Codes 2 To change the DVD regional codes see “Changing DVD Regional Codes” on page 1 - 16.
Features & Components 2 Card Reader Cover Make sure you keep the cover in the card reader when not is use. This will help prevent foreign objects and/or dust getting in to the card reader. 4-in-1 Card Reader The card reader allows you to use some of the latest digital storage cards. Push the card into the slot and it will appear as a removable device, and can be accessed in the same way as your hard disk (s).
Features & Components PC Card Slot The computer is equipped with a PCMCIA 3.3V/5V slot for one type II PCMCIA CardBus PC Card Slot. Make sure you install the PCMCIA/Card Reader Card driver (see “PCMCIA/Card Reader” on page 4 - 10). Inserting and Removing PC Cards • Align the PC Card with the slot and push it in until it locks into place. • To remove a PC Card, simply press the eject button 1 next to the slot. PC Card Slot Cover Make sure you keep the cover in the PC Card slot when not is use.
Features & Components Auto Mail Checker 2 After you have installed the driver for the Auto Mail Checker program (see “AutoMail” on page 4 - 11) you may then configure it to give you notification when you receive new mail. You must be online to receive this notification (note that this program only supports the POP3 protocol), and your default mail program does not need to be open.
Features & Components You may then configure the options for your mailserver, name, password, program and method(s) of notification. Note Check with your Internet Service Provider, network administrator or Mail Service provider for details on what to put on these pages.
Features & Components 2 Application.exe You will need to locate the actual application executable (.exe) file, not just the shortcut. To find the application right-click its shortcut on the desktop and click Properties. Click the shortcut (tab) and see where the executable file is located by clicking the Find Target (button). Application Ap-Key The Ap-key buttons give instant access to the default Internet browser and email program, and to a user-defined application, with one quick button press.
Features & Components TouchPad and Buttons/Mouse The TouchPad is an alternative to the mouse; however, you can also add a mouse to your computer through one of the USB ports. The TouchPad buttons function in much the same way as a two-button mouse. The central button may be configured to function as you require.
Features & Components 2 Sound Volume Adjustment How high the sound volume can be set depends on the setting of the volume control within Windows (and the volume control function keys). Click the Volume icon on the taskbar to check the setting.
Features & Components Adding a Printer The most commonly used peripheral is a printer. The following conventions will help you to add a printer, however it is always best to refer to the printer manual for specific instructions and configuration options. USB Printer Most current printers have a USB interface connection. You may use any one of the ports to connect the printer. Install Instructions: 1. 2. 3. 4. 5.
Features & Components 2 2 - 14
Power Management Chapter 3: Power Management Overview To conserve power, especially when using the battery, your computer uses the ACPI power management system. Power management conserves power by controlling individual components of the computer (the monitor and hard disk drive) or the whole system.
Power Management The Power Sources The computer can be powered by either an AC/DC adapter or a battery pack. 3 AC/DC Adapter Use only the AC/DC adapter that comes with your computer. The wrong type of AC/DC adapter will damage the computer and its components. 1. 2. 3. 4. Attach the AC/DC adapter to the DC-in jack at the rear of the computer. Plug the AC power cord into an outlet, and then connect the AC power cord to the AC/DC adapter (see sidebar if you are using the optional Port Replicator).
Power Management Turning on the Computer Now you are ready to begin using your computer. To turn it on simply press the power button on the front panel. Shutdown When the computer is on, you can use the power button as a Standby/Hibernate/Shutdown hot-key button when it is pressed for less than 4 seconds (pressing and holding the power button for longer than this will shut the computer down). Use Power Options in the Windows control panel to configure this feature.
Power Management 3 Resuming Operation The system can resume from Monitor or Hard Disk Standby by pressing a ley on the keyboard, the Sleep/ Resume key combination (Fn + F4), or power button. Figure 3 - 1 Power Schemes 3 - 4 Power Schemes Power Schemes You can set your computer to conserve power through individual components by means of Power Schemes.
Power Management Each Windows Power Scheme will also adjust the processor performance of your machine in order to save power. This is worth bearing in mind if you are experiencing any reduced performance (especially under DC/battery power). 3 Choose the Home/Office Desk scheme for maximum performance when the computer is powered from an AC power source.
Power Management System Power Options 3 You can use the system power options to stop the computer’s operation and restart where you left off. This system features Standby and Hibernate sleep mode levels (Hibernate mode will need to be enabled by clicking the option in the Hibernate tab in the Power Options control panel - Figure 3 - 2 on page 3 - 7). Hibernate Mode vs. Shutdown Hibernate mode and Shutdown are the same in that the system is off and you need to press the power button to turn it on.
Power Management Standby Standby saves the least amount of power, but takes the shortest time to return to full operation. During Standby the hard disk is turned off, and the CPU is made to idle at its slowest speed. All open applications are retained in memory. When you are not using your computer for a certain length of time, which you specify in the operating system, it will enter Standby mode to save power.
Power Management Configuring the Power Button The power button may be set to send the computer in to either Standby or Hibernate mode (Figure 3 - 3). In Standby mode, the LED will blink green. In Hibernate mode the LED will be off. If you are in a power saving mode set to save power through individual components (e.g. hard disk, monitor), the LED will remain green.
Power Management Battery Information Please follow these simple guidelines to get the best use out of your battery. Low Battery Warning New Battery Always completely discharge, then fully charge, a new battery (see “Battery FAQ” on page 3 - 12 for instructions on how to do this). Battery Life Your computer’s battery life is dependent upon many factors, including the programs you are running, and peripheral devices attached.
Power Management 3 Conserving Battery Power To conserve battery power: Lower the brightness level of the LCD display. The system will decrease LCD brightness slightly to save power when it is not powered by the AC/DC adapter. Close modem or communication applications when they are not being used. Battery life may be shortened through improper maintenance. To optimize the life and improve its performance, fully discharge and recharge the battery at least once every 30 days.
Power Management Proper handling of the Battery Pack • DO NOT disassemble the battery pack under any circumstances • DO NOT expose the battery to fire or high temperatures, it may explode • DO NOT connect the metal terminals (+, -) to each other Damaged Battery Warning Should you notice any physical defects (e.g. the battery is bent out of shape after being dropped), or any unusual smells emanating from the notebook battery, shut your computer down immediately and contact your service center.
Power Management 3 Caution Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Discard used battery according to the manufacturer’s instructions. Battery FAQ How do I completely discharge the battery? Use the computer with battery power until it shuts down due to a low battery.
Drivers & Utilities Chapter 4: Drivers & Utilities This chapter deals with installing the drivers and utilities essential to the operation or improvement of some of the computer’s subsystems. The system takes advantage of some newer hardware components for which the latest versions of most available operating systems haven’t built in drivers and utilities. Thus, some of the system components won’t be auto-configured with an appropriate driver or utility during operating system installation.
Drivers & Utilities Navigate (Browse..) to D: 4 You will notice that many of the instructions for driver installation require you to “Navigate (Browse) to D:”. We assume that you will install all drivers and utilities from the built-in CD device and it is assigned to “Drive D:”. (In addition, all file extensions can be seen.) In this case “D:” is the drive specified for your CD device. Not all computers are setup the same way, and some computers have the CD listed under a different drive letter - e.g.
Drivers & Utilities Service Packs Check the warnings on the following pages regarding installation of the appropriate Service Pack for your Windows OS. Make sure you have installed the appropriate Service Pack before installing all the drivers. Service Pack Installed To see which Service Pack is currently installed on your computer go to the General tab of the System control panel. Right-click the My Computer icon on the desktop or in the Start menu and select Properties.
Drivers & Utilities Authorized Driver Message 4 If you receive a message telling you that the driver you are installing is not authorized (Digital Signature Not Found), just click Yes or Continue Anyway to ignore the message and continue the installation procedure. You will receive this message in cases where the driver has been released after the version of Windows you are currently using. All the drivers provided will have already received certification for Windows.
Drivers & Utilities Driver Installation NoteBook Driver Installation Application Insert the Device Drivers & Utilities + User’s Manual CD-ROM and the NoteBook Driver Installation application will run automatically. If you want to install the driver manually see “Manual Driver Installation” below. 2. 1. 3. 4. 5. 6. Figure 4 - 2 - NoteBook Driver Installation Check the driver installation order from Table 4 1, on page 4 - 6 (the drivers must be installed in this order).
Drivers & Utilities 4 Driver Installation Procedure WinXP SP2 Driver Page # Install the appropriate Service Pack for WinXP Page 4 - 3 Chipset Page 4 - 7 Video (VGA) Page 4 - 7 New Hardware Found Audio Page 4 - 8 Modem Page 4 - 8 LAN Page 4 - 9 AP-Key Buttons Page 4 - 9 TouchPad Page 4 - 10 If you see the message “New Hardware Found” (Found New Hardware Wizard) during the installation procedure (other than when outlined in the driver install procedure), click Cancel to close the window,
Drivers & Utilities Chipset 1. Double-click Chipset from the Notebook Driver Installation menu. OR Click Start (menu) > Run... and navigate (Browse..) to D:\Drivers\00Chipset\Setup.exe and click OK. 2. Click Next > Yes > Next. 3. Click Finish to restart the computer. Video(VGA) 1. Double-click VIDEO from the Notebook Driver Installation menu. OR Click Start (menu) > Run... and navigate (Browse..) to (one of the following) D:\Drivers\01Vga\ATIM26\Setup.exe D:\Drivers\01Vga\ATIM28\Setup.exe and click OK. 2.
Drivers & Utilities 4 Audio 1. Double-click Audio from the Notebook Driver Installation menu. OR Click Start (menu) > Run... and navigate (Browse..) to D:\Drivers\02Audio\Setup.exe and click OK. 2. Click Next. 3. Click Finish to restart the computer. 4. When the computer restarts click Cancel if the The Found New Hardware Wizard appears (click Continue Anyway if asked if you want to continue at any time). 5.
Drivers & Utilities LAN 1. Double-click LAN from the NoteBook Driver Installation menu. OR Click Start (menu) > Run... and navigate (Browse..) to (one of the following) D:\Drivers\04Lan\Marvell\SetupYukonWin.exe D:\Drivers\04Lan\Realtek\Setup.exe and click OK. 2. Click Next. 3. Click “I accept the terms in the license agreement” and click Next > Next >Install. 4. Click Finish. 5. The network settings can now be configured. AP-Key Buttons 1. Double-click AP-key from the Notebook Driver Installation menu.
Drivers & Utilities 4 TouchPad 1. Double-click Touchpad from the Notebook Driver Installation menu. OR Click Start (menu) > Run... and navigate (Browse...) to D:\Drivers\06Touchpad\SETUP.EXE and click OK. 2. Click Next > Next (click Continue Anyway if asked if you want to continue at any time). 3. Click Finish to restart your computer. 4. You may then configure your TouchPad as outlined in “TouchPad and Buttons/ Mouse” on page 2 - 11. 4 - 10 Driver Installation PCMCIA/Card Reader 1.
Drivers & Utilities AutoMail 1. Double-click AutoMail from the Notebook Driver Installation menu. OR Click Start (menu) > Run... and navigate (Browse..) to D:\Drivers\11Automail\SETUP.EXE and click OK. 2. To continue click Next > Next > Finish. 3. For further details see “Auto Mail Checker” on page 2 - 8. Module Drivers Bluetooth See the installation procedure in “Bluetooth Module” on page 7 - 4. PC Camera See the installation procedure in “PC Camera Module” on page 7 - 8.
Drivers & Utilities 4 4 - 12
BIOS Utilities Chapter 5: BIOS Utilities Overview This chapter gives a brief introduction to the computer’s built-in software: Diagnostics: The POST (Power-On Self Test) Configuration: The Setup utility If your computer has never been set up, or you are making important changes to the system (e.g. hard disk setup), then you should review this chapter first and note the original settings found in Setup. Even if you are a beginner, keep a record of the settings you find and any changes you make.
BIOS Utilities POST Screen 5 1.BIOS information 2.CPU type 3.Memory status 4.Enter Setup prompt appears only during POST Note: The POST screen as pictured is for guideline purposes only. The POST screen on your computer may appear slightly different If you have enabled the Boot-time Diagnostic screen (see page 5 - 9) it will bypass the POST.
BIOS Utilities Failing the POST Errors can be detected during the POST. There are two categories, “fatal” and “non-fatal”. Fatal Errors These stop the boot process and usually indicate there is something seriously wrong with your system. Take the computer to your service representative or authorized service center as soon as possible. Non-Fatal Errors This kind of error still allows you to boot.
BIOS Utilities The Setup Program The Phoenix Setup program tells the system how to configure itself and manage basic features and subsystems (e.g. port configuration). Entering Setup 5 To enter Setup, turn on the computer and press F2 during the POST. The prompt (Press F2 to Enter Setup) seen in Figure 5 - 1 is usually present for a few seconds after you turn on the system. If you get a “Keyboard Error”, (usually because you pressed F2 too quickly) just press F2 again.
BIOS Utilities Setup Screens The following pages contain additional advice on portions of the Setup. Setup Menus Along the top of the screen is a menu bar with five (5) menu headings. When you select a heading, a new screen appears. Scroll through the features listed on each screen to make changes to Setup. Instructions on how to navigate each screen are in the box along the bottom of the screen.
BIOS Utilities Main Menu Figure 5 - 2 Main Menu PhoenixBIOS Setup Utility Main Main Advanced System Time: Boot Exit Item Specific Help [22:11:05] 06 [07/21/2005] System Date: IDE Channel 0 Master IDE Channel 0 Slave SATA Port 1 5 Security [20004MB] [CD-ROM] [None] , , or selects field.
BIOS Utilities IDE Channel 0 Master/Slave (Main Menu) Pressing Enter opens the sub-menu to show the configuration of either a CD Device or HDD that on the computer’s IDE Channel 0. Use the Auto (Type:) setting to have the items configured automatically for you. SATA Port 1(Main Menu) Pressing Enter here opens the sub-menu to show the configuration of any hard disks on the computer’s SATA Port 1. Use the Auto (Type:) setting to have the item configured automatically for you.
BIOS Utilities Advanced Menu Figure 5 - 3 Advanced Menu PhoenixBIOS Setup Utility Advanced Advanced Main Security Boot Exit Item Specific Help Advanced Chipset Control Select options for Advanced Chipset features.
BIOS Utilities National 383 SIO Control Sub-Menu (Advanced Menu) Pressing Enter here will provide a sub-menu that controls the configuration of National 383 SIO devices such as the serial port, and/or the infrared transceiver (FIR Device). Legacy USB Support (Advanced Menu) Use this menu item to enable/disable the support for Legacy Universal Serial Bus. Legacy USB support allows USB devices (usually those which don’t require drivers) to be used in operating systems other than Windows (e.g. DOS).
BIOS Utilities Security Menu Figure 5 - 4 Security Menu PhoenixBIOS Setup Utility Main Advanced Security Security Boot Exit Item Specific Help 5 Supervisor Password Is: Clear Set Supervisor Password Password on boot: [E Enter] [Disabled] Fixed disk boot sector: [Normal] Supervisor Password controls access to the setup utility. Security Menu The changes you make here affect the access to the Setup utility itself, and also access to your machine as it boots up after you turn it on.
BIOS Utilities Password on boot: (Security Menu) Specify whether or not a password (supervisor or user password) should be entered to boot the computer. If “Enabled” is selected, only users who enter a correct password can boot the system (see the warning in the sidebar). The default setting is “Disabled”. Note: To clear existing passwords press Enter and type the existing password, then press Enter for the new password (without typing any password entry) and Enter again to confirm the password clearance.
BIOS Utilities Boot Menu PhoenixBIOS Setup Utility Figure 5 - 5 Main Advanced Security Boot Exit Boot Menu Item Specific Help Boot priority order: 1: IDE 0: TOSHIBA MK2023GAS-(PM) 2: IDE 1: PIONEER DVD-RW DVR-K15RA3: IDE 2: 4: USB FDC: 5: 5 Excluded from boot order: : USB HDD: : USB CDROM: F1 Esc Help Exit Select Item Select Menu -/+ Enter Keys used to view or configure devices: Up and Down arrows select a device. <+> and <-> moves the device up or down.
BIOS Utilities When you specify a device as a boot device on the Boot Menu, it requires the availability of an operating system on that device. Most home computers come with an operating system already installed on “Drive C:”. If you wish to boot from a CD-ROM/DVD-ROM you will need to add it to the boot order. As a general rule the order below is recommended: 1. 2. 3. 4.
BIOS Utilities Figure 5 - 6 Configuring the Network Boot Protocol Boot Agent Menu 1 Enabling Network Boot 5 Go to the Advanced > Advanced Chipset Control menu to enable the Giga LAN PXE OPROM option. Realtek RTL8110S/8169S Gigabit Boot Agent Press Shift-F10 to configure ......... 2 Realtek RTL8110S/8169S Gigabit Boot Agent Configuration Menu v1.50 Network Boot Protocol Boot Order Show Config Message Show Message Time PXE PnP/BEV(BBS) Enable 3 Seconds Save the changes and exit.
BIOS Utilities Exit Menu Figure 5 - 7 PhoenixBIOS Setup Utility Main Advanced Security Boot Exit Menu Exit Exit Item Specific Help Exit Saving Changes Exit Discarding Changes Load Setup Defaults Discard Changes Save Changes F1 Esc Help Exit Select Item Select Menu Exit System Setup and save your changes to CMOS.
BIOS Utilities 5 5 - 16
Upgrading The Computer Chapter 6: Upgrading The Computer Overview This chapter contains information on upgrading the computer. Follow the steps outlined to make the desired upgrades. If you have any trouble or problems you can contact your service representative for further help.
Upgrading The Computer Power Safety Warning 6 Before you undertake any upgrade procedures, make sure that you have turned off the power, and disconnected all peripherals and cables (including telephone lines). It is advisable to also remove your battery in order to prevent accidentally turning the machine on. When Not to Upgrade These procedures involve opening the system’s case, adding and sometimes replacing parts.
Upgrading The Computer Removing the Battery If you are confident in undertaking upgrade procedures yourself, for safety reasons it is best to remove the battery. 1. 2. 3. Warranty Warning Please check with your service representative before undertaking any upgrade procedures to find out if this will VOID your warranty. Turn the computer off, and turn it over. Slide the latch 1 in the direction of the arrow, and hold it in place. Lift the battery out at point 2 , in the direction of the arrow 3 .
Upgrading The Computer HDD System Warning 6 New HDD’s are blank. Before you begin make sure: You have backed up any data you want to keep from your old HDD. You have all the CDROMs and FDDs required to install your operating system and programs. If you have access to the internet, download the latest application and hardware driver updates for the operating system you plan to install. Copy these to a removable medium.
Upgrading The Computer For Model A computers (see overleaf for Model B): 3. 4. 5. 6. Remove screws 12 - 14 from the hard disk assembly. Pull the tab upward and lift the assembly 15 out of the computer. Remove the 4 screws 16 - 19 to release the hard disk from the assembly cover, and remove the connector 20 . Reverse the process to install any new hard disk.
Upgrading The Computer For Model B computers: 7. 8. 9. Remove screws 22 & 23 from the hard disk assembly. Pull the tab upward and lift the assembly 24 out of the computer. Remove the 4 screws 25 - 28 to release the hard disk from the assembly cover. 10. Reverse the process to install any new hard disk.
Upgrading The Computer Upgrading the Optical (CD/DVD) Device 1. 2. 3. 4. Turn off the computer, and turn it over and remove the battery. Slide the latch 1 in the direction of the arrow, and hold it in place. Eject the optical device by carefully sliding the latch 2 in the direction of the arrow. Reverse the process to install the new device.
Upgrading The Computer Upgrading the System Memory (RAM) The computer has two memory sockets for 200 pin Small Outline Dual In-line (SO-DIMM) DDRII (DDR2) type memory modules (see “Memory” on page C - 2 for details of supported module types). The total memory size is automatically detected by the POST routine once you turn on your computer. 1. 2. 6 Turn off the computer, and turn it over and remove the battery. Locate the bay cover and remove screws 1 - 5 Model A, OR screws 1 11 Model B.
Upgrading The Computer 3. Gently pull the two release latches on the sides of the memory socket in the direction indicated by the arrows ( 12 & 13 ) in Figure 6 - 7. Figure 6 - 7 RAM Module Location 12 13 Contact Warning 4. The RAM module will 14 pop-up, and you can remove it. 14 14 Be careful not to touch the metal pins on the module’s connecting edge. Even the cleanest hands have oils which can attract particles, and degrade the module’s performance.
Upgrading The Computer 5. 6. 6 Pull the latches to release the second module if necessary. Insert a new module holding it at about a 30° angle and fit the connectors firmly into the memory slot. 7. The module’s pin alignment will allow it to only fit one way. Make sure the module is seated as far into the slot as it will go. DO NOT FORCE the module; it should fit without much pressure. 8. Press the module in and down towards the mainboard until the slot levers click into place to secure the module. 9.
Upgrading The Computer Inserting the 2nd Hard Disk 1. 2. 3. 4. 5. Turn off the computer, and turn it over and remove the battery. Slide the latch 1 in the direction of the arrow, and hold it in place. Eject the installed device (CD/DVD, battery or HDD) by carefully sliding the latch 2 in the direction of the arrow. Turn the computer over again, so that the top of the computer is facing upwards. Insert the new hard disk until the lock clicks firmly back in place.
Upgrading The Computer Warranty The CPU is not a user serviceable part. Opening this compartment, or accessing the CPU in any way, may violate your warranty. 6 Upgrading the Processor If you want to upgrade your computer by replacing the existing processor with a faster/new one you will need to contact your customer service representative. We recommend that you do not do this yourself, since if it is done incorrectly you may damage the processor or mainboard.
Modules & Options Chapter 7: Modules & Options Overview This chapter contains the information on the WLAN, Bluetooth, PC Camera and TV Tuner modules which may come with your computer, depending on the configuration purchased. If you are unsure please contact your service representative.
Modules & Options Wireless Device Operation Aboard Aircraft 7 Intel PRO/Wireless Mini-PCI WLAN Module If you have included an Intel PRO/Wireless 2915ABG (802.11a/b/g) MiniPCI WLAN module in your purchase option, you will have the appropriate software CD provided for your module. The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the module(s) are OFF if you are using the computer aboard aircraft.
Modules & Options Intel WLAN Driver Installation 1. Make sure the module is powered on, then insert the Intel PROSet/ Wireless CD-ROM into the CD/DVD drive. 2. Click Install Software (button). 3. Click the button to accept the license and click Next > Next > OK. 4. Click OK to complete the installation. 5. You can configure the settings by going to the Intel (R) PROSet Wireless control panel (Start > Programs/All Programs > Intel PROSet Wireless), or by double-clicking the taskbar icon .
Modules & Options Wireless Device Operation Aboard Aircraft The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the module(s) are OFF if you are using the computer aboard aircraft. 7 Use the Fn + F12 key combination to toggle power to the optional Bluetooth module, and check the indicator to see if the module(s) is powered on or not (see Table 1 - 2, on page 1 9/Table 1 - 4, on page 1 11).
Modules & Options Send To Bluetooth User Guide Right-Click to select any file and scroll down to Send To ... Bluetooth Device. View the BlueSoleil User Guides from the Help Menu (or press the F1 key) in the IVT Corporation BlueSoleil - Main Window control panel. Click BlueSoleil User Guides in the Contents tab, and click to select the appropriate User Guide from the panel on the right.
Modules & Options Bluetooth Audio Setup If you wish to use Bluetooth audio devices, it is necessary to setup the audio recording options in Windows (see Figure 7 - 4 on page 7 - 7). 1. 2. 3. 4. 5. 7 Go to the Start menu and point to Settings (or just click Control Panel) and click Control Panel, then double-click the Sounds & Audio Devices icon (Sounds, Speech, and Audio Devices in Category View). Click Advanced in the Device volume tab. Click Options, scroll down and click Properties.
Modules & Options Figure 7 - 4 Bluetooth Audio Setup (Windows XP) 7 Click to make volume controls appear.
Modules & Options Taking Still Pictures Double-click the My Computer icon on the desktop, or go the Start menu and point to My Computer, then click it. Double-click the BisonCam, NB Pro icon. . 7 PC Camera Module If you have included an PC Camera module in your purchase option, you will have the appropriate software CD provided for your module. Before installing the PC Camera driver, make sure that the optional PC Camera is on (the LED will be green).
Modules & Options Sertek PC Camera Driver Installation (WinXP) 1. Press the Fn + F10 key combination to power on the PC Camera module (click Cancel if you see a “New Hardware Found” message). 2. Insert the PC Camera CD-ROM into the CD/DVD drive. 3. The program will run automatically. 4. Click Install Products. 5. Choose the language you prefer and click OK. 6. Click Next (click Continue Anyway if asked if you want to continue). 7.
Modules & Options PC Camera Audio Setup If you wish to capture video & audio with your camera, it is necessary to setup the audio recording options in Windows (see Figure 7 - 5 on page 7 - 11). 1. 7 Go to the Start menu and point to Settings (or just click Control Panel) and click Control Panel, then double-click the Sounds & Audio Devices icon (Sounds, Speech, and Audio Devices in Category View). 2. Click Advanced in the Device volume tab. 3. Click Options, scroll down and click Properties. 4.
Modules & Options Figure 7 - 5 PC Camera Audio Setup (Windows XP) 7 PC Camera Module 7 - 11
Modules & Options Pre-Allocating File Space You may pre-allocate the file size for the capture file in the BisonCap program. You can choose to ignore this by clicking Cancel. 7 Pre-allocating space on the hard disk can improve the capture quality (particularly of large capture files), by reducing the amount of work the hard disk has to do in finding space for the video data as it is being captured. You may find it helpful to defragment the HDD before capture.
Modules & Options Eliminating Screen Flicker If you find that the video screen in the BisonCap program is flickering, you can try to adjust the setting in the Video Capture Filter options. 1. 2. 3. Run the BisonCap program. Go to Options and scroll down to select “Video Capture Filter...”. Click either 50Hz or 60Hz under Frequency in Property Page (tab).
Modules & Options TV Tuner Remote The remote control unit provided with the optional TV Tuner will only function when the computer is powered from the AC adapter, and not while the computer is powered by the internal battery. 7 Point the remote at the consumer IR transceiver to change channels etc. TV Tuner Module Options You may have one of two possible optional Mini-PCI TV Tuner modules supplied with your computer, depending on your purchase configuration.
Modules & Options LifeView FlyDVB-T Hybrid Mini-PCI TV Tuner Module If your purchase includes the LifeView FlyDVB-T Hybrid Mini-PCI TV Tuner Module, then install the driver and application as per the instructions below. Installing the LifeView FlyDVB-T Driver 1. Insert the driver CD-ROM into the CD/DVD drive. 2. Double-click LifeView DTV and Driver. 3. Choose the language you prefer, and click OK. 4. Click Next > Next. 5. Click Finish to restart the computer. 6.
Modules & Options MPC622-MCE TV Tuner Note that this TV Tuner module supports Windows Media Center Edition Only. 7 YUAN PVR Mini-PCI MPC622-MCE TV Tuner Module If your purchase includes the YUAN PVR MPC622-MCE TV Tuner for Windows XP Media Center Edition, then you will need to install the driver as per the instructions below. In order to watch TV channels you will need to purchase a copy of Cyberlink Power DVD 5.0. Installing the MPC622 Driver for Windows XP Media Center Edition (MCE) 1.
Troubleshooting Chapter 8: Troubleshooting Overview Should you have any problems with your computer, before consulting your service representative, you may want to try to solve the problem yourself. This chapter lists some common problems and their possible solutions. This can’t anticipate every problem, but you should check here before you panic. If you don’t find the answer in these pages, make sure you have followed the instructions carefully and observed the safety precautions in the preface.
Troubleshooting Basic Hints and Tips Many of the following may seem obvious but they are often the solution to a problem when your computer appears not to be working. • Power - Is the computer actually plugged into a working electrical outlet? If plugged into a power strip, make sure it is actually working. Check the LED Power & Communication Indicators (see “LED Indicators” on page 1 - 9) to see the computer’s power status.
Troubleshooting Backup and General Maintenance • Always backup your important data, and keep copies of your OS and programs safe, but close to hand. Don’t forget to note the serial numbers if you are storing them out of their original cases, e.g. in a CD wallet. • Run maintenance programs on your hard disk and OS as often as you can. You may schedule these programs to run at times when you are not using your computer.
Troubleshooting Viruses • Install an Anti-Virus program and keep the definitions file (the file which tells your program which viruses to look for) up to date. New computer viruses are discovered daily, and some of them may seriously harm your computer and cause you to lose data. Anti-Virus programs are commercially available and the definitions file updates are usually downloadable directly from the internet. • Be careful when opening e-mail from sources you don’t know.
Troubleshooting Upgrading and Adding New Hardware/Software • Do not be tempted to make changes to your Windows Registry unless you are very sure of what you are doing, otherwise you will risk severely damaging your system. • Don’t open your computer or undertake any repair or upgrade work if you are not comfortable with what you are doing. • Read the documentation.
Troubleshooting • Thoroughly check any recent changes you made to your system as these changes may affect one or more system components, or software programs. If possible, go back and undo the change you just made and see if the problem still occurs. • Don’t over complicate things.
Troubleshooting Problems and Solutions Problem Possible Cause - Solution You turned on the power but it doesn’t work. Battery missing / incorrectly installed. Check the battery bay, make sure the battery is present and seated properly (the design of the battery only allows it to go in one way). Make sure there’s nothing interfering with the battery contacts. The Audio "DJ" player is on.
Troubleshooting Problem Possible Cause - Solution The computer feels too hot. Make sure the computer is properly ventilated and the Vent/Fan intakes are not blocked. If this doesn’t cool it down, put the system into Hibernate mode or turn it off for an hour. Make sure the computer isn’t sitting on a thermal surface (see “Overheating” on page 1 14). Make sure you’re using the correct adapter.
Troubleshooting Problem Possible Cause - Solution No image appears on the external monitor I have plugged in and powered on. You haven’t installed the video driver and configured it appropriately from the Control Panel. See “ATI Video Driver Controls” on page B - 1 for instructions on installing and configuring the video driver. You forget password. If you forget the password, you may have to discharge the battery of the CMOS. Contact your service representative for help.
Troubleshooting 8 Problem Possible Cause - Solution The compact disc tray will not open when there is a disc in the tray. The compact disc is not correctly placed in the tray. Gently try to remove the disc using the eject hole (see “Loading Discs” on page 2 - 3). The DVD regional codes can no longer be changed. The code has been changed the maximum 5 times. See “DVD Regional Codes” on page 2 - 5. The Audio “DJ” CD Player will not turn on (nothing appears on the LCD of the player).
Troubleshooting Problem Possible Cause - Solution The Wireless LAN/ Bluetooth/ PC Camera modules cannot be configured. The driver(s) for the module(s) have not been installed. Make sure you have installed the driver for the appropriate module (see the instructions for the appropriate module in “Modules & Options” on page 7 - 1).
Troubleshooting 8 8 - 12
Interface (Ports & Jacks) Appendix A: Interface (Ports & Jacks) Overview The following chapter will give a quick description of the interface (ports & jacks) which allow your computer to communicate with external devices, connect to the internet etc.
Interface (Ports & Jacks) Notebook Ports and Jacks Item Built-In Microphone Description The built-in microphone allows you to record on your computer Card Reader Port The card reader allows you to use some of the latest digital storage cards. Push the card into the slot and it will appear as a removable device. CATV-In Jack Use this jack to connect a CATV cable if you have included the optional Mini-PCI TV Tuner in your purchase.
Interface (Ports & Jacks) Item Line-In Jack Description The Line-In jack allows you to play audio sources through the computer’s speakers. Microphone-In Jack Plug an external microphone in to this jack to record on your computer. Mini-IEEE 1394 Port This port allows a high-speed connection to various peripheral devices, e.g. external disk drives and digital cameras (see note below). Mini-IEEE 1394a Port The Mini-IEEE 1394 port only supports SELF POWERED IEEE 1394a devices.
Interface (Ports & Jacks) Item Description Security Lock Slot To prevent possible theft, a Kensington-type lock can be attached to this slot. Locks can be purchased at any computer store. Serial Port A Connect a serial type mouse to this port. S/PDIF-Out Jack This S/PDIF (Sony/Philips Digital Interface Format) Out Jack allows you to connect your DVD-capable PC to a Dolby AC-3 compatible receiver for “5.1” or ‘dts’ surround sound.
ATI Video Driver Controls Appendix B: ATI Video Driver Controls The basic settings for configuring the LCD are outlined in “Video Features” on page 1 - 19. ATI Video Driver Installation Make sure you install the drivers in the order indicated in Table 4 - 1, on page 4 - 6. 1. Double-click VIDEO from the Notebook Driver Installation menu. OR Click Start (menu) > Run... and navigate (Browse..) to (one of the following) D:\Drivers\01Vga\ATIM26\Setup.exe D:\Drivers\01Vga\ATIM28\Setup.exe and click OK. 2.
ATI Video Driver Controls ATI Taskbar Icon You can also access ATI Mobility Radeon X700/X800 XT Properties by right-clicking the ATI icon in the taskbar. Point to Settings and click ATI Display Settings, then click Settings (tab). ATI Mobility Radeon Properties More advanced video configuration options are provided in the ATI Mobility Radeon X700/X800 XT Properties control panel: 1. 2. 3. Open the Display Properties (see “Video Features” on page 1 - 19) control panel. Click Advanced (button).
ATI Video Driver Controls Help Menus Right-click on almost any item in the tabs to bring up the “What’s This?” button. Click the “What’s This?” button to bring up the help menu. Help Menu PowerPlay Menu The menus pictured in this chapter are from the ATI Mobility Radeon X700. The X800 XT has an additional PowerPlay menu with power saving features.
ATI Video Driver Controls Theater Mode Theater Mode can be enabled by clicking Theater Mode Options (button) in the Overlay tab from the ATI Mobility Radeon Properties. (see Figure B - 2). Theater Mode enables you to display video playback in full screen on a secondary monitor. B Theater Mode is not supported if you have the TV Tuner module installed. Display Devices Besides the built-in LCD, you can also use an external monitor/flat panel display or TV as your display device.
ATI Video Driver Controls Attaching Other Displays If you prefer to use a monitor or flat panel display, connect it to the DVI-Out Port at the rear of the computer. 1. 2. 3. 4. 5. Attach your external monitor to the DVI-Out port (or TV to the S-Video-Out port), and turn it on. Select the Displays tab in ATI Mobility Radeon Properties. Click the enable/disable button / for the display device you wish to use. Click Apply. Click Yes to accept the settings and OK to save the changes.
ATI Video Driver Controls Primary & Clone Displays The Primary display in an Extended Desktop environment will be associated with display Icon 1 in the settings tab. The Clone display will set the associated display to show a copy of the Primary desktop. B The Clone display in an Extended Desktop environment will show the portion of the desktop extended from the Primary display. B - 6 Display Modes Display Modes Single Only one of your displays is used.
ATI Video Driver Controls Clone Mode Clone Mode simply shows an exact copy of the Primary display desktop on the other display(s). This mode will drive multiple displays with the same content. Use this feature to display the screen through a projector for a presentation. Each display device can be configured independently as this allows you to set the options for overhead projectors etc., which require specific resolutions and refresh rates.
ATI Video Driver Controls Extended Desktop Mode The system supports Extended Desktop in multiple display environments in Windows XP. An Extended Desktop creates a desktop spanning multiple displays and acts as a large workspace. To get this effect: 1. 2. 3. 4. 5. 6. 7. 8. 9. B B - 8 Display Modes Attach your external monitor to the DVI-Out port (or TV to the S-Video Out port), and turn it on. Select the Displays tab in the ATI Mobility Radeon Properties.
ATI Video Driver Controls 10. In the example shown in Figure B - 5 the primary monitor 1 is on the left, the other display is on the right. Help Click either the Display popup menu, or click the icon for the appropriate display. Further help is available through the taskbar menus (see Figure B - 1 on page B - 2). Then click the tick box to extend the primary display’s desktop to it. Figure B - 5 Extended Desktop Monitor Arrangement B 11.
ATI Video Driver Controls 12. One display will be set to as one as set to Primary. Primary. The displays may be switched as long Figure B - 6 Displays Tab (Extended Desktop Mode) In this picture the notebook LCD panel is the primary display, and the desktop may be extended to any attached displays. 13.
ATI Video Driver Controls Enabling TV Display To display desktop images on a TV, connect the TV to your computer by using an S-Video cable from the TV to the S-Video-Out jack at the rear of the computer (see “System Map: Rear View” on page 1 - 14). Further help is available to help you troubleshoot your TV connection through the menus accessed from the taskbar (see page Figure B - 1 on page B - 2).
ATI Video Driver Controls The TV Properties tabs allow you to adjust the TV settings and TV Format etc.
Specifications Appendix C: Specifications Latest Specification Information The specifications listed in this Appendix are correct at the time of going to press. Certain items (particularly processor types/speeds and CD/DVD device types) may be changed or updated due to the manufacturer's release schedule. Check with your service center for details.
Specifications Feature Processor Celeron Processors are Available for Model A Computers Only: C Specification Intel Pentium® M Processor (478-pin) Micro-FC-PGA Package Models 730/ 740/ 750/ 760/ 770/ 780 (µ0.09) 0.09 Micron Process Technology 2MB On-die L2 Cache & 533MHz FSB 1.6/ 1.73/ 1.86/ 2/ 2.13/ 2.26 GHz Intel Celeron® M Processor (478-pin) Micro-FCPGA Package Models 350/ 350J/ 360/ 360J/ 370/ 380/ 390 (µ0.09) 0.09 Micron Process Technology 1MB On-die L2 Cache & 400MHz FSB 1.3/ 1.3/ 1.4/ 1.4/ 1.
Specifications Feature Video Card Options Specification Model A Computers: Model B Computers: ATI Mobility Radeon X700 (M26) PCI Express Video Card 128/256MB DDR Video RAM On Board 256-bit Video Memory Interface PCI Express * 16 Fully Supports DirectX® 9 ATI Mobility Radeon X700 (M26) PCI Express Video Card 128MB DDR Video RAM On Board 256-bit Video Memory Interface PCI Express * 16 Fully Supports DirectX® 9 OR ATI Mobility Radeon X800 XT (M28 PRO) PCI Express Video Card 256MB DDR-III (DDR3) Video RAM O
Specifications Feature Storage Specification One Changeable 12.7mm(h) Optical Device (CD/DVD) Type Drive (see “Optional” on page C 7 for drive options) in Removable Bay One Removable Bay for 2nd Battery or 2nd PATA Hard Disk Drive or Optical Disk Drive Easy Changeable 2.5" 9.5 mm (h) Hard Disk Drive Supporting ATA 100/ 66/ 33 or SATA 150 The System Supports both PATA (Parallel) and SATA (Serial) Interfaces Audio 7.
Specifications Feature Interface & Communication Specification Four USB 2.0 Ports One Mini-IEEE 1394 Port One DVI-Out Port One Microphone-In Jack One Line-In Jack One Headphone-Out Jack One S/PDIF Output Jack One Serial Port One S-Video-Out Jack 300K Pixel PC VIdeo Camera Module with USB Interface (Factory Option) OR 1.3M Pixel PC VIdeo Camera Module with USB Interface (Factory Option) Bluetooth 1.2 Module with USB Interface (Optional) Wireless Network Options Intel PRO/Wireless 2915ABG (802.
Specifications Feature Specification Keyboard & Pointing Device Winkey Keyboard Built-In TouchPad with Scrolling Function PCMCIA One Type-II PCMCIA CardBus PC Card Slot Power Management Supports ACPI 2.0 Supports Hibernate Mode Supports Standby Power Power Supply - Model A Computers: Power Supply - Model B Computers: Full Range AC/DC Adapter 20V, 4.5A (90 Watts), 100~240V, 47~63Hz Full Range AC/DC Adapter 20V, 6.0A (120 Watts), 100~240V, 47~63Hz 8 Cell Smart Lithium-Ion Battery Pack, 4.
Specifications Feature Optional Specification Optical Drive Module Options: DVD/CD-RW Combo Drive Module DVD-Dual Drive Module Bluetooth 1.2 Module with USB Interface 8 Cell Smart Lithium-Ion Battery Pack, 4.4AH 2nd Battery - 6 Cell Smart Lithium-Ion Battery Pack, 3.8AH 300K Pixel PC VIdeo Camera Module with USB Interface (Factory Option) OR 1.3M Pixel PC VIdeo Camera Module with USB Interface (Factory Option) Wireless Network Options Intel PRO/Wireless 2915ABG (802.
Specifications C C - 8
