Preface Notice The company reserves the right to revise this publication or to change its contents without notice. Information contained herein is for reference only and does not constitute a commitment on the part of the manufacturer or any subsequent vendor. They assume no responsibility or liability for any errors or inaccuracies that may appear in this publication nor are they in anyway responsible for any loss or damage resulting from the use (or misuse) of this publication.
Preface FCC Statement (Federal Communications Commission) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Preface IMPORTANT SAFETY INSTRUCTIONS Follow basic safety precautions, including those listed below, to reduce the risk of fire, electric shock, and injury to persons when using any electrical equipment: 1. 2. 3. 4. 5. Do not use this product near water, for example near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool. Avoid using this equipment with a telephone line (other than a cordless type) during an electrical storm.
Preface Instructions for Care and Operation The notebook computer is quite rugged, but it can be damaged. To prevent this, follow these suggestions: 1. Don’t drop it, or expose it to shock. If the computer falls, the case and the components could be damaged. Do not expose the computer to any shock or vibration. 2. Do not place anything heavy on the computer. Keep it dry, and don’t overheat it. Keep the computer and power supply away from any kind of heating element. This is an electrical appliance.
Preface 3. Avoid interference. Keep the computer away from high capacity transformers, electric motors, and other strong magnetic fields. These can hinder proper performance and damage your data. 4. Follow the proper working procedures for the computer. Shut the computer down properly and don’t forget to save your work. Remember to periodically save your data as data may be lost if the battery is depleted. Do not turn off the power until you properly shut down all programs. 5.
Preface Power Safety The computer has specific power requirements: Power Safety Warning Before you undertake any upgrade procedures, make sure that you have turned off the power, and disconnected all peripherals and cables (including telephone lines). It is advisable to also remove your battery in order to prevent accidentally turning the machine on. • Only use a power adapter approved for use with this computer.
Preface Battery Precautions • Only use batteries designed for this computer. The wrong battery type may explode, leak or damage the computer. • Do not remove any batteries from the computer while it is powered on. • Do not continue to use a battery that has been dropped, or that appears damaged (e.g. bent or twisted) in any way. Even if the computer continues to work with a damaged battery in place, it may cause circuit damage, which may possibly result in fire.
Preface Cleaning Do not apply cleaner directly to the computer; use a soft clean cloth. Do not use volatile (petroleum distillates) or abrasive cleaners on any part of the computer. Servicing Do not attempt to service the computer yourself. Doing so may violate your warranty and expose you and the computer to electric shock. Refer all servicing to authorized service personnel. Unplug the computer from the power supply.
Preface Travel Considerations Packing As you get ready for your trip, run through this list to make sure the system is ready to go: 1. 2. 3. 4. 5. 6. 7. 8. Check that the battery pack and any spares are fully charged. Power off the computer and peripherals. Close the display panel and make sure it’s latched. Disconnect the AC/DC adapter and cables. Stow them in the carrying bag. The AC/DC adapter uses voltages from 100 to 240 volts so you won’t need a second voltage adapter.
Preface On the Road In addition to the general safety and maintenance suggestions in this preface, and Chapter 8: Troubleshooting, keep these points in mind: Hand-carry the notebook - For security, don’t let it out of your sight. In some areas, computer theft is very common. Don’t check it with “normal” luggage. Baggage handlers may not be sufficiently careful. Avoid knocking the computer against hard objects.
Preface Developing Good Work Habits Developing good work habits is important if you need to work in front of the computer for long periods of time. Improper work habits can result in discomfort or serious injury from repetitive strain to your hands, wrists or other joints. The following are some tips to reduce the strain: • Adjust the height of the chair and/or desk so that the keyboard is at or slightly below the level of your elbow. Keep your forearms, wrists, and hands in a relaxed position.
Preface Lighting Proper lighting and comfortable display viewing angle can reduce eye strain and muscle fatigue in your neck and shoulders. • • • • Position the display to avoid glare or reflections from overhead lighting or outside sources of light. Keep the display screen clean and set the brightness and contrast to levels that allow you to see the screen clearly. Position the display directly in front of you at a comfortable viewing distance. Adjust the display-viewing angle to find the best position.
Preface Contents Notice .................................................................................I FCC Statement .............................................................II Instructions for Care and Operation .......................... IV Power Safety .............................................................. VI Battery Precautions ...................................................VII Cleaning .................................................................. VIII Servicing ...............
Preface Power Management Drivers & Utilities Overview ........................................................................3-1 Advanced Configuration and Power Interface ............3-1 The Power Sources ........................................................3-2 AC/DC Adapter ...........................................................3-2 Battery .........................................................................3-2 Turning on the Computer ...............................................
Preface BIOS Utilities Overview ........................................................................5-1 The Power-On Self Test (POST) ...................................5-2 Failing the POST .........................................................5-3 Fatal Errors .................................................................5-3 Non-Fatal Errors .........................................................5-3 The Setup Program ........................................................5-4 Entering Setup ...
Preface User Enrollment ..........................................................7-7 Trusted Platform Module .............................................7-10 Initializing TPM .......................................................7-10 TPM User Set Up .....................................................7-13 Initialize the TPM for use with the Protector Suite Software ...........................................7-15 Troubleshooting Overview ..................................................................
Preface PCMCIA ....................................................................... C-3 Card Reader .................................................................. C-3 Interface ........................................................................ C-3 Communication ............................................................. C-4 Power Management ...................................................... C-4 Power ............................................................................
Preface XVIII
Quick Start Guide Chapter 1: Quick Start Guide Overview This Quick Start Guide is a brief introduction to the basic features of your computer, to navigating around the computer and to getting your system started. The remainder of the manual covers the following: • Chapter 2 A guide to using some of the main features of the computer e.g. the storage devices (hard disk, optical device, 4-in-1 card reader, PC Card), Touch Pad & Mouse, Audio & Printer. • Chapter 3 The computer’s power saving options.
1 Quick Start Guide Model Designs This notebook series includes two different model designs which vary slightly in color and appearance. However both designs incorporate the same features, ports and jacks etc. Advanced Users If you are an advanced user you may skip over most of this Quick Start Guide. However you may find it useful to refer to Chapter 4 (Drivers), Chapter 5 (BIOS), Chapter 6 (Upgrading) and Chapter 7 (Modules & Options). You may also find the notes marked with a of interest to you.
Quick Start Guide Not Included Operating Systems (e.g. Windows XP) and applications (e.g. word processing, spreadsheet and database programs) have their own manuals, so please consult the appropriate manuals. System Software Your computer may already come with system software pre-installed. Where this is not the case, or where you are re-configuring your computer for a different system, you will find this manual refers to the Microsoft Windows XP (Home & Professional Editions) operating system.
1 Quick Start Guide System Startup 1. 2. 3. 4. 5. 6. 7. Remove all packing materials. Place the computer on a stable surface. Securely attach any peripherals you want to use with the notebook (e.g. keyboard and mouse) to their ports. Attach the AC/DC adapter to the DC-In jack at the rear of the computer, then plug the AC power cord into an outlet, and connect the AC power cord to the AC/DC adapter. Raise the lid/LCD to a comfortable viewing angle, and press the power button to turn the computer “on”.
Quick Start Guide System Map: Top View with LCD Panel Open 1. 2. 3. 4. 5. 6. 7. 8. 9. Wireless Device Operation Aboard Aircraft 1 The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the module(s) are OFF if you are using the computer aboard aircraft.
1 Quick Start Guide LED Indicators The LED indicators on the computer display helpful information about the current status of the computer.
Quick Start Guide Keyboard & Hot Keys The keyboard has a numerical keypad for easy numeric data input, and features function keys to allow you to change operational features instantly. . Numeric Keypad NumLk & ScrLk Keys The touchpad (button) and WLAN (switch) hot keys give instant access to the functions indicated in the table below. Visual indicators are available when the hot key driver is installed (see “Hot Key Utility” on page 4 - 10).
1 Quick Start Guide Function Keys The function keys (F1 - F12 etc.) will act as hot keys when pressed while the Fn key is held down. In addition to the basic function key combinations; visual indicators are available for certain key combinations/hot keys when the hot key driver is installed (see “Hot Key Utility” on page 4 - 10).
Quick Start Guide System Map: Front & Rear Views Figure 1 - 4 Front & Rear Views 1 3 4 2 5 1. 2. 3. 4. 5. 6. 6 LED Indicators LCD Latch RJ-11 Phone Jack RJ-45 LAN Jack Battery DC-In Jack 10 Cell Battery Warning Please be careful when using the 10 cell battery. Battery Information Always completely discharge, then fully charge, a new battery before using it. Completely discharge and charge the battery at least once every 30 days or after about 20 partial discharges.
1 Quick Start Guide System Map: Left View Figure 1 - 5 - Left View 1. 2. 3. 4. 5. 6. Vent/Fan Intake/Outlet External Monitor Port 1 * USB 2.0 Port Mini-IEEE 1394 Port 4-in-1 Card Reader PC Card Slot 1 5 2 3 6 4 Mini-IEEE 1394 Port The Mini-IEEE 1394 Port only supports SELF POWERED IEEE 1394 devices. Overheating 4-in-1 Card Reader To prevent your computer from overheating make sure nothing blocks the vent(s)/ fan intake(s)/outlet(s) while the computer is in use.
Quick Start Guide System Map: Right View Figure 1 - 6 - Right View 1. 1 2 4 3 Changing DVD Regional Codes Go to the Control Panel and double-click System > Hardware (tab), click Device Manager, then click the + next to DVD/CD-ROM drives. Double-click on the DVD-ROM device to bring up the Properties dialogue box, and select the DVD Region (tab) to bring up the control panel to allow you to adjust the regional code (see “DVD Regional Codes” on page 2 - 5).
1 Quick Start Guide System Map: Bottom View Figure 1 - 7 - Bottom View 1. 2. 3. 4. 5. 6. 2 Vent/Fan Intake/Outlet Battery Optical (CD/DVD) Device Drive Release Cover Component Bay Cover Hard Disk Drive Bay Cover Speaker 3 CPU The CPU is not a user serviceable part. Opening this compartment, or accessing the CPU in any way, may violate your warranty. Overheating To prevent your computer from overheating make sure nothing blocks the vent(s)/fan intake(s)/outlet(s) while the computer is in use.
Quick Start Guide Windows XP Start Menu & Control Panel Most of the control panels, utilities and programs within Windows XP (and most other Windows versions) are accessed from the Start menu. When you install programs and utilities they will be installed on your hard disk drive, and a shortcut will usually be placed in the Start menu and/or the desktop. You can customize the look of the Start menu by right-clicking the Start menu and selecting Properties from the menu.
1 Quick Start Guide Video Features Your computer has built-in Intel on-board video. You can switch display devices, and configure display options, from the Display Properties control panel in Windows as long as the appropriate video driver is installed. To access Display Properties in Windows: 1. 2. 3. 4. 5. 6. 7. 8. 9. Click Start, point to Settings and click Control Panel (or just click Control Panel). Double-click Display (icon) - In the Appearances and Themes category.
Quick Start Guide 1 2 3 Figure 1 - 9 - Display Properties Desktop Intel Display Mode Description Single Mode One of the connected displays is used as the display device Twin Mode This mode will drive multiple displays with the same content and resolutions, color quality etc.
1 Quick Start Guide Power Management Features The Power Options control panel icon in Windows (see page 1 - 13) allows you to configure power management features for your computer. You may conserve power through individual components such as the monitor or hard disk (by means of Power Schemes), or you may use either Stand by or Hibernate mode to conserve power throughout the system (enable Hibernate support from the control panel as pictured in Figure 1 - 10).
Features & Components Chapter 2: Features & Components Overview 2 Read this chapter to learn more about the following main features and components of the computer: • • • • • • • Hard Disk Drive Optical (CD/DVD) Device 4-in-1 Card Reader PC Card Slot TouchPad and Buttons/Mouse Audio Features Adding a Printer Overview 2 - 1
Features & Components 2 Power Safety Before attempting to access any of the internal components of your computer please ensure that the machine is not connected to the AC power, and that the machine is turned off. Also ensure that all peripheral cables, including phone lines, are disconnected from the computer. Hard Disk Drive The hard disk drive is used to store your data in the computer. The hard disk can be taken out to accommodate other 2.5" or 1.
Features & Components Optical (CD/DVD) Device There is a bay for a 5.25" optical (CD/DVD) device (9.5mm height). The actual device will depend on the module you purchased (see “Storage” on page C - 3). The optical device is usually labeled “Drive D:” and may be used as a boot device if properly set in the BIOS (see “Boot Menu” on page 5 - 15).
Features & Components Handling CDs or DVDs 2 CD Emergency Eject If you need to manually eject a CD (e.g. due to an unexpected power interruption) you may push the end of a straightened paper clip into the emergency eject hole. However please do NOT use a sharpened pencil or similar object that may break and become lodged in the hole. Proper handling of your CDs/DVDs will prevent them from being damaged. Please follow the advice below to make sure that the data stored on your CDs/DVDs can be accessed.
Features & Components DVD Regional Codes To change the DVD regional codes see “Changing DVD Regional Codes” on page 1 - 11. 2 .
Features & Components 2 Card Reader Cover Make sure you keep the cover in the card reader when not is use. This will help prevent foreign objects and/or dust getting in to the card reader. 4-in-1 Card Reader The card reader allows you to use some of the latest digital storage cards. Push the card into the slot and it will appear as a removable device, and can be accessed in the same way as your hard disk (s). Make sure you install the PCMCIA/Card Reader driver (see “PCMCIA/CardReader” on page 4 - 9).
Features & Components PC Card Slot The computer is equipped with a PCMCIA 3.3V/5V slot for one type II PCMCIA CardBus PC Card Slot. Make sure you install the PCMCIA/Card Reader driver (see “PCMCIA/CardReader” on page 4 - 9). Inserting and Removing PC Cards • Align the PC Card with the slot and push it in until it locks into place. • To remove a PC Card, simply press the eject button 1 next to the slot. PC Card Slot Cover Make sure you keep the cover in the PC Card slot when not is use.
Features & Components 2 Mouse Driver If you are using an external mouse your operating system may be able to auto-configure your mouse during its installation or only enable its basic functions. Be sure to check the device’s user documentation for details. TouchPad and Buttons/Mouse The TouchPad is an alternative to the mouse; however, you can also add a mouse to your computer through one of the USB ports. The TouchPad buttons function in much the same way as a two-button mouse.
Features & Components Audio Features You can configure the audio options on your computer from the Sounds and Audio Devices Windows control panel, or from the Realtek HD Audio Manager icon in the taskbar/control panel (this will bring up the Realtek Audio Configuration menus). The volume may also be adjusted by means of the Fn + F9/F10 key combination.
Features & Components 2 Parallel Printer After setting up the printer attach the parallel cable to the printer. Connect the printer’s parallel cable to the Parallel to USB converter, and then plug the converter into the USB port. Turn ON the printer, then turn ON the computer. Windows will identify the printer and either load one of its own drivers or ask you to supply one. Follow the on-screen instructions. Adding a Printer The most commonly used peripheral is a printer.
Power Management Chapter 3: Power Management Overview To conserve power, especially when using the battery, your computer uses the ACPI power management system. Power management conserves power by controlling individual components of the computer (the monitor and hard disk drive) or the whole system.
Power Management The Power Sources The computer can be powered by either an AC/DC adapter or a battery pack. 3 AC/DC Adapter Use only the AC/DC adapter that comes with your computer. The wrong type of AC/ DC adapter will damage the computer and its components. 1. 2. 3. 4. Attach the AC/DC adapter to the DC-in jack at the rear of the computer. Plug the AC power cord into an outlet, and then connect the AC power cord to the AC/DC adapter. Raise the lid/LCD to a comfortable viewing angle.
Power Management Turning on the Computer Now you are ready to begin using your computer. To turn it on simply press the power button on the front panel. When the computer is on, you can use the power button as a Stand by/Hibernate/ Shutdown hot key button when it is pressed for less than 4 seconds (pressing and holding the power button for longer than this will shut the computer down). Use Power Options in the Windows control panel to configure this feature.
Power Management 3 Resuming Operation Press a key on the keyboard, or move the mouse/TouchPad to resume from Monitor or Hard Disk Stand by. Figure 3 - 1 Power Schemes 3 - 4 Power Schemes Power Schemes You can set your computer to conserve power through individual components by means of Power Schemes.
Power Management Each Windows Power Scheme will also adjust the processor performance of your machine in order to save power. This is worth bearing in mind if you are experiencing any reduced performance (especially under DC/battery power). 3 Choose the Home/Office Desk scheme for maximum performance when the computer is powered from an AC power source.
Power Management System Power Options 3 You can use the system power options to stop the computer’s operation and restart where you left off. This system features Stand by and Hibernate sleep mode levels (Hibernate mode will need to be enabled by clicking the option in the Hibernate tab in the Power Options control panel - Figure 3 - 2 on page 3 - 7). Hibernate Mode vs. Shutdown Hibernate mode and Shutdown are the same in that the system is off and you need to press the power button to turn it on.
Power Management Stand by Stand by saves the least amount of power, but takes the shortest time to return to full operation. During Stand by the hard disk is turned off, and the CPU is made to idle at its slowest speed. All open applications are retained in memory. When you are not using your computer for a certain length of time, which you specify in the operating system, it will enter Stand by mode to save power.
Power Management Configuring the Power Button The power button may be set to send the computer in to either Stand by or Hibernate mode (Figure 3 - 3). In Stand by mode, the LED will blink green. In Hibernate mode the LED will be off. If you are in a power saving mode set to save power through individual components (e.g. hard disk, monitor), the LED will remain green.
Power Management Battery Information Please follow these simple guidelines to get the best use out of your battery. Low Battery Warning New Battery Always completely discharge, then fully charge, a new battery (see “Battery FAQ” on page 3 - 12 for instructions on how to do this). Battery Life Your computer’s battery life is dependent upon many factors, including the programs you are running, and peripheral devices attached.
Power Management 3 Conserving Battery Power To conserve battery power: Lower the brightness level of the LCD display. The system will decrease LCD brightness slightly to save power when it is not powered by the AC/DC adapter. Close modem or communication applications when they are not being used. Remove any unused PC Card from the computer (PC Cards quickly use up battery power even if the system enters sleep mode). Disconnect any unnecessary external devices.
Power Management Proper handling of the Battery Pack • DO NOT disassemble the battery pack under any circumstances • DO NOT expose the battery to fire or high temperatures, it may explode • DO NOT connect the metal terminals (+, -) to each other 3 Damaged Battery Warning Should you notice any physical defects (e.g. the battery is bent out of shape after being dropped), or any unusual smells emanating from the notebook battery, shut your computer down immediately and contact your service center.
Power Management Battery FAQ 3 Caution Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Discard used battery according to the manufacturer’s instructions. How do I completely discharge the battery? Use the computer with battery power until it shuts down due to a low battery.
Drivers & Utilities Chapter 4: Drivers & Utilities This chapter deals with installing the drivers and utilities essential to the operation or improvement of some of the computer’s subsystems. The system takes advantage of some newer hardware components for which the latest versions of most available operating systems haven’t built in drivers and utilities. Thus, some of the system components won’t be auto-configured with an appropriate driver or utility during operating system installation.
Drivers & Utilities Navigate (Browse..) to D: 4 You will notice that many of the instructions for driver installation require you to “Navigate (Browse) to D:”. We assume that you will install all drivers and utilities from the built-in CD device and it is assigned to “Drive D:”. In addition, all file extensions can be seen In this case “D:” is the drive specified for your CD device. Not all computers are setup the same way, and some computers have the CD listed under a different drive letter - e.g.
Drivers & Utilities Service Packs Check the warnings on the following pages regarding installation of the appropriate Service Pack for your Windows OS. Make sure you have installed the appropriate Service Pack before installing all the drivers. Service Pack Installed To see which Service Pack is currently installed on your computer go to the General tab of the System control panel. Right-click the My Computer icon on the desktop or in the Start menu and select Properties.
Drivers & Utilities 4 Authorized Driver Message Updating/Reinstalling Individual Drivers If you receive a message telling you that the driver you are installing is not authorized (Digital Signature Not Found), just click Yes or Continue Anyway to ignore the message and continue the installation procedure. If you wish to update/reinstall individual drivers it may be necessary to uninstall the original driver.
Drivers & Utilities Driver Installation 1. Insert the Device Drivers & Utilities + User’s Manual CD-ROM and click Install WinXP Drivers (button). 2. If you wish to install the drivers manually see page 4 - 6. 3. Check the driver installation order from Table 4 - 1, on page 4 - 6 (the drivers must be installed in this order) which is the same as that listed in the Drivers Installer menu below.
Drivers & Utilities 4 Service Pack Installation WinXP SP2 Driver Page # Install the appropriate Service Pack for WinXP Page 4 - 3 Chipset Page 4 - 7 Video Page 4 - 7 New Hardware Found Audio Page 4 - 7 LAN Page 4 - 8 Modem Page 4 - 8 PCMCIA/Card Reader Page 4 - 9 If you see the message “New Hardware Found” (Found New Hardware Wizard) during the installation procedure (other than when outlined in the driver install procedure), click Cancel to close the window, and follow the installation
Drivers & Utilities Chipset 1. Click 1.Install Chipset Driver > Yes. OR Click Start (menu) > Run... and navigate (Browse..) to D:\Drivers\Chipset\Setup.exe and click OK. 2. Click Next > Yes > Next. 3. Click Finish to restart the computer. Video 1. Click 2.Install Video Driver > Yes. OR Click Start (menu) > Run... and navigate (Browse..) to D:\Drivers\Video\Setup.exe and click OK. 2. To continue click Next > Yes. 3. Click Finish to restart the computer. Audio 1. Click 3. Install Audio Driver > Yes.
Drivers & Utilities LAN Note that you should click Cancel if a Found New Hardware Wizard appears before installing the LAN driver. 4 1. Click 4.Install LAN Driver > Yes. OR Click Start (menu) > Run... and navigate (Browse..) to D:\Drivers\LAN\SetupYukonWin.exe and click OK. 2. Click Next. 3. Click the button to accept the license, and then click Next > Install > Finish. 4. The network settings can now be configured 4 - 8 Driver Installation Modem 1. Click 5.Install Modem Driver > Yes.
Drivers & Utilities PCMCIA/CardReader 1. Click 6.Install CardReader Driver > Yes. OR Click Start (menu) > Run... and navigate (Browse...) to D:\Drivers\CardReader\setup.exe and click OK. 2. Click Next. 3. Click Finish. TPM (Trusted Platform Module) 1. Click 7.Install TPM Driver > Yes. OR Click Start (menu) > Run... and navigate (Browse...) to D:\Drivers\TPM\setup.exe and click OK. 2. Click Next. 3. Click the button to accept the license, and then click Next > Next > Next > Install. 4.
Drivers & Utilities 4 Fingerprint Reader 1. Click 8.Install Fingerprint Driver > Yes. OR Click Start (menu) > Run... and navigate (Browse..) to D:\Drivers\Fingerprint\autorun.exe and click OK. 2. Click Software Installation (button). 3. Click Next. 4. Click the button to accept the license, and then click Next. 5. Click Next > Next > Next. 6. Click Finish > Yes to restart the computer. 7. See “Security Modules (Fingerprint & TPM)” on page 7 - 6 for configuration instructions.
BIOS Utilities Chapter 5: BIOS Utilities Overview This chapter gives a brief introduction to the computer’s built-in software: Diagnostics: The POST (Power-On Self Test) Configuration: The PhoenixBIOS Setup Utility If your computer has never been set up, or you are making important changes to the system (e.g. hard disk setup), then you should review this chapter first and note the original settings found in the PhoenixBIOS Setup Utility.
BIOS Utilities POST Screen 5 Note that the POST screen as pictured will not appear if you have enabled Intel OnScreen Branding (see page 5 - 9). 1.BIOS information 2.CPU type 3.Memory status 4.Enter Setup prompt appears only during POST Note: The POST screen as pictured is for guideline purposes only. The Power-On Self Test (POST) Each time you turn on the computer, the system takes a few seconds to conduct a POST, including a quick test of the on-board RAM (memory).
BIOS Utilities Failing the POST Errors can be detected during the POST. There are two categories, “fatal” and “nonfatal”. Fatal Errors These stop the boot process and usually indicate there is something seriously wrong with your system. Take the computer to your service representative or authorized service center as soon as possible. Non-Fatal Errors This kind of error still allows you to boot.
BIOS Utilities The Setup Program The Phoenix Setup program tells the system how to configure itself and manage basic features and subsystems (e.g. port configuration). Entering Setup 5 To enter the PhoenixBIOS Setup Utility, turn on the computer and press F2 during the POST. The prompt (Press F2 to Enter Setup) seen in Figure 5 - 1 on page 5 2 is usually present for a few seconds after you turn on the system.
BIOS Utilities Setup Screens The following pages contain additional advice on portions of the Setup. Setup Menus Along the top of the screen is a menu bar with six (6) menu headings. When you select a heading, a new screen appears. Scroll through the features listed on each screen to make changes to Setup. Instructions on how to navigate each screen are in the box along the bottom of the screen.
BIOS Utilities Main Menu Figure 5 - 2 PhoenixBIOS Setup Utility Main Menu Main Main Advanced Security Power Boot Exit Item Specific Help System Overview -------------------------------------------------------- 5 , , or selects field. BIOS Ver:1.00.
BIOS Utilities System Time & Date (Main Menu) The hour setting uses the 24-hour system (i.e., ØØ = midnight; 13 = 1 pm). If you can change the date and time settings in your operating system, you will also change these settings. Some applications may also alter data files to reflect these changes. System Memory: (Main Menu) This item contains information on the system memory, and is not user configurable. The system will auto detect the amount of memory installed.
BIOS Utilities Advanced Menu Figure 5 - 3 PhoenixBIOS Setup Utility Advanced Menu Advanced Advanced Main Security Power Boot Exit Item Specific Help Advanced Settings WARNING: Setting wrong values in below sections may cause system to malfunction.
BIOS Utilities Internal Pointing Device (Advanced Menu) Use this item to enable/disable the internal TouchPad (alternatively you can use the TouchPad power button to enable/disable the TouchPad). Onboard LAN Boot ROM (Advanced Menu) This item may be used to enable/disable the network boot option. 5 Wake-Up On LAN (Advanced Menu) Enable/Disable the Wake-Up On LAN option here. Wake-Up on LAN (WOL) is a standard that allows you to turn on a computer from another location over a network connection.
BIOS Utilities Security Menu PhoenixBIOS Setup Utility Security Menu 5 The changes you make here affect the access to the Setup utility itself, and also access to your machine as it boots up after you turn it on. These settings do not affect your machine or network passwords which will be set in your software OS.
BIOS Utilities Set User Password (Security Menu) You can set a password for user mode access to the PhoenixBIOS Setup Utility. This will not affect access to the computer OS, (only the PhoenixBIOS Setup Utility). Many menu items in the PhoenixBIOS Setup Utility utility cannot be modified in user mode. You can only set the user password after you have set the supervisor password. Password Check (Security Menu) Specify here when the system should prompt for a password.
BIOS Utilities Password Protection 5 Note that you should set a supervisor password in the BIOS to protect the TPM information from being tampered with by unauthorized users. Set HDD Password (Security Menu) Press Enter to create a password for access to the computer’s hard disk when the computer boots up. I/O Interface Security (Security Menu) The submenus here allow you to enable/disable the interface controllers for Bluetooth, PC Card/Card Reader, USB/Finger Print ID, LAN and Audio/Modem.
BIOS Utilities Power Menu PhoenixBIOS Setup Utility Main Advanced Security Power Figure 5 - 5 Boot Exit Power Menu Item Specific Help Start Battery Calibration Press Enter to start calibrating a battery. The calibration should charge the battery to full and then discharge it to empty.
BIOS Utilities Start Battery Calibration (Power Menu) Press Enter to start the battery calibration process. The system will prompt you to plug-in the AC/DC adapter and will begin to charge the battery to full capacity. Once the battery has reached full capacity you will then be prompted to remove the AC/DC adapter with the computer left on. This will completely discharge the battery. Once the computer has turned off the battery will be fully discharged.
BIOS Utilities Boot Menu PhoenixBIOS Setup Utility Main Advanced Security Power Boot Figure 5 - 6 Exit Boot Menu Item Specific Help Boot Settings ---------------------------------------------------------Boot priority order: 1: USB FDC: 2: USB KEY: 3: IDE CDROM: 4: ODD: UJDA775 DVD/CDRW-(PS) 5: HDD: HTC426030G5CE00-(PM) 6: 7: 8: Excluded from boot order: : USB HDD: : Network: : Other USB: F1 Esc Help Exit Select Item Select Menu -/+ Enter Keys used to view or configure devices: Up and Dow
BIOS Utilities Exit Menu Figure 5 - 7 Exit Menu PhoenixBIOS Setup Utility Main Advanced Security Power Boot Exit Item Specific Help Exit Saving Changes Exit Discarding Changes Load Setup Defaults Discard Changes Save Changes 5 F1 Esc Help Exit Select Item Select Menu Exit System Setup and save your changes to CMOS.
Upgrading The Computer Chapter 6: Upgrading The Computer Overview This chapter contains information on upgrading the computer. Follow the steps outlined to make the desired upgrades. If you have any trouble or problems you can contact your service representative for further help.
Upgrading The Computer When Not to Upgrade Power Safety Warning 6 Before you undertake any upgrade procedures, make sure that you have turned off the power, and disconnected all peripherals and cables (including telephone lines). It is advisable to also remove your battery in order to prevent accidentally turning the machine on. These procedures involve opening the system’s case, adding and sometimes replacing parts.
Upgrading The Computer Removing the Battery If you are confident in undertaking upgrade procedures yourself, for safety reasons it is best to remove the battery. Your computer may come with a 4 cell battery 4 , or a 10 cell battery 5 , depending on your purchase configuration. 1. 2. 3. 4. The battery is heavy and extends beyond the case of the computer. Moving the battery, or exposing it to shock or vibration may interrupt the battery contacts and cause the computer to shutdown.
Upgrading The Computer HDD System Warning 6 New HDD’s are blank. Before you begin make sure: You have backed up any data you want to keep from your old HDD. You have all the CD-ROMs and FDDs required to install your operating system and programs. If you have access to the internet, download the latest application and hardware driver updates for the operating system you plan to install. Copy these to a removable medium.
Upgrading The Computer 3. Remove the hard disk bay cover 4 (and foam top cover 5 for 1.8" hard disks). Figure 6 - 3 Hard Disk Bay Cover Removal 4 4 6 5 4. Carefully lift the hard disk assembly up and disconnect the cable at point 6 .
Upgrading The Computer 5. 6. 6 Figure 6 - 5 Hard Disk Removal Remove the hard disk 7 from the bay, and then remove the case 8 . Reverse the process to install any new hard disk.
Upgrading The Computer Upgrading the Optical (CD/DVD) Device Drive 1. 2. 3. 4. Turn off the computer, and turn it over and remove the battery. Locate the ODD release cover and remove the screw 1 and cover 2 . Use a screwdriver to carefully push out the optical device at point 3 . Reverse the process to install the new device.
Upgrading The Computer Upgrading the System Memory (RAM) The computer has one memory sockets for 200 pin Small Outline Dual In-line (SODIMM) DDRII (DDR2) type memory modules (see “Memory” on page C - 2 for details of supported module types). The total memory size is automatically detected by the POST routine once you turn on your computer. 1. 2. Turn off the computer, and turn it over and remove the battery. Locate the component bay cover and remove screws 1 & 2 .
Upgrading The Computer 3. Carefully remove the component bay cover 3 . Figure 6 - 8 3 Component Cover Removal 4. 6 Gently pull the two release latches 4 & 5 on the sides of the memory socket.
Upgrading The Computer 5. The RAM module 6 will pop-up, and you can remove it. Contact Warning 6 Be careful not to touch the metal pins on the module’s connecting edge. Even the cleanest hands have oils which can attract particles, and degrade the module’s performance. 6 Figure 6 - 10 RAM Module Removal 6. Insert a new module holding it at about a 30° angle and fit the connectors firmly into the memory slot. 7. The module’s pin alignment will allow it to only fit one way.
Modules & Options Chapter 7: Modules & Options Overview This chapter contains the information on the Bluetooth, WLAN and Security modules which may come with your computer, depending on the configuration purchased. If you are unsure please contact your service representative. • Bluetooth Module • Intel PRO/Wireless WLAN Module • Security Modules (Fingerprint & TPM) Wireless Device Operation Aboard Aircraft The use of any portable electronic transmission devices aboard aircraft is usually prohibited.
Modules & Options Wireless Device Operation Aboard Aircraft The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the module(s) are OFF if you are using the computer aboard aircraft. 7 Use the Fn + F2 key combination to toggle power to the optional Bluetooth module, and check the indicator to see if the module(s) is powered on or not.
Modules & Options 9. Configure the settings by going to the IVT Corporation BlueSoleil - Main Window control panel (Start > Programs/All Programs > IVT BlueSoleil > BlueSoleil), or click the taskbar icon . Send To Bluetooth Right-Click to select any file and scroll down to Send To... Bluetooth Device. User Guide View the BlueSoleil User Guides from the Help Menu (or press the F1 key) in the IVT Corporation BlueSoleil Main Window. The Manual in Adobe .
Modules & Options Wireless Device Operation Aboard Aircraft The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the module(s) are OFF if you are using the computer aboard aircraft. 7 Intel PRO/Wireless WLAN Module If you have included an Intel PRO/Wireless 3945ABG (802.11a/b/g) PCIe WLAN module in your purchase option, make sure that the Wireless LAN module is on (the LED will be green) before installing the driver.
Modules & Options Intel WLAN Driver Installation 1. Make sure the module is powered on, and then insert the Device Drivers & Utilities + User’s Manual CD-ROM into the CD/DVD drive. 2. Click Install WinXP Drivers (button), and then click 11.Install WLAN Driver > Yes. OR Click Start (menu) > Run... and navigate (Browse..) to D:\Drivers\WLAN\Autorun.exe and click OK. 3. Click Install Software (button). 4. Click the button to accept the license and click Next > Next > OK. 5.
Modules & Options Password Warning If you set passwords for any of the security modules, NEVER forget your password. 7 The consequences of this could be serious. If you cannot remember your boot password you must contact your vendor and you may lose all of the information on your hard disk.
Modules & Options Fingerprint Reader Make sure you have installed the Trusted Platform Module (see page 4 - 9) and Fingerprint (see page 4 - 10) drivers before configuring the fingerprint and security system. Make sure you have administrator’s rights to your computer, and have a Windows password enabled for full security protection. Before beginning the enrollment process it is recommended that you go through the fingerprint tutorial.
Modules & Options 7. Fingerprint Enrollment Note that it is strongly recommended that you enroll more than one finger in case of injury etc. Click Next for each window of the tutorial (you can click the button to “skip tutorial” at any time). 8. Click the button above any of the fingers to begin the enrollment process for that finger. 9. Swipe the finger three times to enroll that finger. 10. Repeat the process for all the fingers you wish to enroll (see sidebar), and then click Next. 11.
Modules & Options 15. See “Help & Manual” on page 7 - 7 for further details. 16. If you swipe your finger over the reader at any time you can access the Biomenu to lock the computer, register websites, Unlock My Safe, open the Control Center and access the Help menu. 17. The Control Center allows you to change the Settings, enroll Fingerprints and get Help. 18. The My Safe storage folder on the desktop allows you to store documents with added security protection. 19.
Modules & Options Trusted Platform Module Before setting up the TPM functions you must initialize the security platform. Backup & Archive Note that it is very important to perform routine backup and archive procedures. 7 This is the only way to recover if the TPM fails, the information is cleared or the computer develops a problem. Initializing TPM 1. 2. 3. 4. 5. 6. Restart the computer.
Modules & Options 7. 8. 9. Click Start > Programs/All Programs > Infineon Security Platform Solution > Manage Security Platform, or double-click the taskbar icon , to bring up the Infineon Security Platform Initialization Wizard. Click User Settings (tab), and then click Yes. Click Next and select either Initialize a new Security Platform, or Restore a Security Platform from a Backup Archive, and click Next.
Modules & Options 12. If you have chosen to set an Automatic Backup you will need to browse to a location for the backup, and you can also Schedule any backups required. Recovery & Password Reset Tokens 7 It is strongly recommended that you save your Recovery/Password Reset Tokens to a removable medium (e.g. a USB flash memory drive), and that you backup this/these token(s) and save it/them in a safe location. Figure 7 - 8 Backup and Emergency Recovery 13.
Modules & Options 15. Click Next to confirm the settings. 16. If you want to use the TPM for this account select Start Security Platform User Initialization Wizard and click Finish. Figure 7 - 9 Initialization Screens 17. The Wizard will now continue to take you through setting up a user (or see below). TPM User Set Up To use the TPM you must be set up as a user. You can manually add users as follows: 1. 2. 3. 4.
Modules & Options 5. Save a location for a Basic User Password reset file, and click Next. Help To learn more about all the features click Start > Programs/All Programs > Infineon Security Platform Solution > Help on Security Platform. 7 Figure 7 - 10 User Initialization Screens 6. 7. Click Next to confirm the settings. Select the Security Platform Features you require: Note: Make sure you select File and folder encryption with Encrypting File System to have the TPM work with the Fingerprint ID. 8.
Modules & Options Initialize the TPM for use with the Protector Suite Software 1. 2. 3. Click Start > Programs/All Programs > Protector Suite QL > Control Center, or select the Control Center from the Biomenu or right click the taskbar icon and select Start Control Center. Click Settings > System Settings. Click TPM (tab). Figure 7 - 11 Initialize TPM 7 4. 5. Click Initialize TPM (button). Click Next > Finish and close the control panels.
Modules & Options 7 7 - 16
Troubleshooting Chapter 8: Troubleshooting Overview Should you have any problems with your computer, before consulting your service representative, you may want to try to solve the problem yourself. This chapter lists some common problems and their possible solutions. This can’t anticipate every problem, but you should check here before you panic. If you don’t find the answer in these pages, make sure you have followed the instructions carefully and observed the safety precautions in the preface.
Troubleshooting Basic Hints and Tips Many of the following may seem obvious but they are often the solution to a problem when your computer appears not to be working. • Power - Is the computer actually plugged into a working electrical outlet? If plugged into a power strip, make sure it is actually working. Check the LED Indicators (see “LED Indicators” on page 1 - 6) to see the computer’s power status. • Connections - Check all the cables to make sure that there are no loose connections anywhere.
Troubleshooting Backup and General Maintenance • Always backup your important data, and keep copies of your OS and programs safe, but close to hand. Don’t forget to note the serial numbers if you are storing them out of their original cases, e.g. in a CD wallet. • Run maintenance programs on your hard disk and OS as often as you can. You may schedule these programs to run at times when you are not using your computer.
Troubleshooting Viruses • Install an Anti-Virus program and keep the definitions file (the file which tells your program which viruses to look for) up to date. New computer viruses are discovered daily, and some of them may seriously harm your computer and cause you to lose data. Anti-Virus programs are commercially available and the definitions file updates are usually downloadable directly from the internet. • Be careful when opening e-mail from sources you don’t know.
Troubleshooting Upgrading and Adding New Hardware/Software • Do not be tempted to make changes to your Windows Registry unless you are very sure of what you are doing, otherwise you will risk severely damaging your system. • Don’t open your computer or undertake any repair or upgrade work if you are not comfortable with what you are doing. • Read the documentation.
Troubleshooting • Thoroughly check any recent changes you made to your system as these changes may affect one or more system components, or software programs. If possible, go back and undo the change you just made and see if the problem still occurs. • Don’t over complicate things.
Troubleshooting Problems & Possible Solutions Problem Possible Cause - Solution You turned on the power but it doesn’t work. Battery missing / incorrectly installed. Check the battery bay, make sure the battery is present and seated properly (the design of the battery only allows it to go in one way). Make sure there’s nothing interfering with the battery contacts. The battery LED power indicator , is blinking orange. Low Battery. Plug in the DC power source.
Troubleshooting Problem Possible Cause - Solution The computer feels too hot. Make sure the computer is properly ventilated and the Vent/Fan intakes are not blocked. If this doesn’t cool it down, put the system into Hibernate mode or turn it off for an hour. Make sure the computer isn’t sitting on a thermal surface (see “Overheating” on page 1 - 12). Make sure you’re using the correct adapter.
Troubleshooting Problem You forget password. the Possible Cause - Solution boot If you forget the password, you may have to discharge the battery of the CMOS. Contact your service representative for help. Password Warning If you choose to set a boot password, NEVER forget your password. The consequences of this could be serious. If you cannot remember your boot password you must contact your vendor and you may lose all of the information on your hard disk.
Troubleshooting Problem Unwelcome numbers appear when typing. Possible Cause - Solution If the LED is lit, then Num Lock is turned ON. (see “LED Indicators” on page 1 - 6). Other Keyboards If your keyboard is damaged or you just want to make a change, you can use any standard USB keyboard. The system will detect and enable it automatically. However special functions/hot keys unique to the system’s regular keyboard may not work. 8 The system freezes or the screen goes dark.
Interface (Ports & Jacks) Appendix A: Interface (Ports & Jacks) Overview The following chapter will give a quick description of the interface (ports & jacks) which allow your computer to communicate with external devices, connect to the internet etc.
Interface (Ports & Jacks) Notebook Ports and Jacks Item Built-In Microphone Card Reader Port DC-In Jack Description The built-in microphone allows you to record on your computer The card reader allows you to use some of the latest digital storage cards. Push the card into the slot and it will appear as a removable device. Plug the supplied AC/DC adapter into this jack to power your computer.
Interface (Ports & Jacks) Item Description Mini-IEEE 1394 Port This port allows a high-speed connection to various peripheral devices, e.g. external disk drives and digital cameras (see note below). Mini-IEEE 1394 Port The Mini-IEEE 1394 port only supports SELF POWERED IEEE 1394 devices. RJ-11 Phone Jack RJ-45 LAN Jack This port connects to the built-in modem. You may plug the telephone line directly into this RJ-11 telephone connection. Note: Broadband (e.g.
Interface (Ports & Jacks) Item Description USB 2.0/1.1 Ports These USB 2.0 compatible ports (USB 2.0 is fully USB 1.1 compliant) are for low-speed peripherals such as keyboards, mice or scanners, and for high-speed peripherals such as external HDDs, digital video cameras or high-speed scanners etc.
Intel Video Driver Controls Appendix B: Intel Video Driver Controls The basic settings for configuring the LCD are outlined in “Video Features” on page 1 - 14. Intel Video Driver Installation Make sure you install all the drivers in the order indicated in Table 4 - 1, on page 4 - 6. Instructions for installing the video driver are repeated below. 1. Click 2.Install Video Driver > Yes. OR Click Start (menu) > Run... and navigate (Browse..) to D:\Drivers\Video\Setup.exe and click OK. 2.
Intel Video Driver Controls DVMT Notes DVMT is not user-configurable. DVMT is not local video memory. DVMT will not function in MS-DOS. DOS uses the legacy memory indicated. Figure B - 1 DVMT Memory Requirements B Dynamic Video Memory Technology Intel® DVMT 3.0 automatically and dynamically allocates as much (up to 128MB) system memory (RAM) as needed to the video system (the video driver must be installed - see page B - 1). DVMT returns whatever memory is no longer needed to the operating system.
Intel Video Driver Controls Intel Graphics Properties More advanced video configuration options are provided by the Intel(R) Graphics Media Accelerator Driver for Mobile. 1. 2. 3. Open Display Properties (see “Video Features” on page 1 - 14) and click Advanced. Click the Intel(R)... tab and click Graphics Properties (button). You can also access Intel(R) GMA Driver for Mobile by double-clicking the Windows control panel, or from the taskbar icon menu.
Intel Video Driver Controls Help Menus You may make changes to the devices, color, schemes, Hot Keys etc. by clicking the appropriate menu item or button. Click Information (button) to obtain useful information about the graphics properties of the computer, and see the Support tab in Information to get weblinks to the latest information on the Intel Website. Right-click on many of the items in the tabs to bring up the “What’s This?” button. Click the “What’s This?” button to bring up the help menu.
Intel Video Driver Controls Scheme Options Use Scheme Options to configure quick settings for applications which require specific resolution and color settings in order to run properly e.g. games, multimedia programs. To set the scheme options: 1. 2. 3. 4. 5. 6. 7. 8. 9. Open the Intel(R) GMA Driver for Mobile control panel (see “Intel Graphics Properties” on page B - 3). Configure your display configuration, resolution etc. as per your requirements from Display Settings.
Intel Video Driver Controls Intel Display Note Note that the notebook is the default Primary display device and may not be changed. Attaching Other Displays Besides the built-in LCD, you can also use an external monitor/flat panel display as a display device. The following are the display options: 1. 2. The built-in LCD OR an external monitor/flat panel display connected to the external monitor port (Single Display).
Intel Video Driver Controls Display Modes Single Display Only one of your attached displays is used. Twin This mode will drive multiple displays with the same content and resolutions, color quality etc. See “Twin Mode Support” on page B - 8 for more information. Intel(R) Dual Display Clone This mode will drive multiple displays with the same content. Each device may be configured independently for different resolutions, refresh rates, color quality etc.
Intel Video Driver Controls To Enable Intel(R) Dual Display Clone Mode OR Twin Mode Twin Mode Support The Twin mode option will only appear if the notebook and external monitor support the same resolution (e.g. 1280 * 800). Check any documentation supplied with an external monitor to see supported resolutions. 1. 2. 3. 4. 5. Attach your external display to the external monitor port and turn it on. Open the Intel(R) GMA Driver for Mobile control panel (see “Intel Graphics Properties” on page B - 3).
Intel Video Driver Controls To Enable Extended Desktop Mode: 1. 2. 3. 4. 5. Attach your external monitor to the external monitor port and turn it on. Open the Intel(R) GMA Driver for Mobile control panel (see “Intel Graphics Properties” on page B - 3). Click to choose Extended Desktop from Display Devices (tab). Click Apply, and OK to confirm the settings change. Click Display Settings to adjust the settings for the attached devices.
Intel Video Driver Controls To Enable Extended Desktop (Display Properties) Display Settings Extended Desktop Use the control panel to drag the monitors to match the physical arrangement you wish to use. 1. 2. 3. 4. 5. You can drag any icons or windows across to either display desktop, which makes it possible to have one program visible in one of the displays, and a different program visible in the other display.
Specifications Appendix C: Specifications C Latest Specification Information The specifications listed in this Appendix are correct at the time of going to press. Certain items (particularly processor types/speeds and CD/DVD device types) may be changed or updated due to the manufacturer's release schedule. Check with your service center for details.
Specifications C Feature Processor (CPU On Board) Specification Intel® Core™ Solo Processor FC-PGA6 Package U1400 65nm (65 Nanometer) Process Technology 2MB On-die L2 Cache & 533MHz FSB 1.20 GHz Intel® Celeron® M Processor FC-PGA6 Package ULV 423 65nm (65 Nanometer) Process Technology 1MB On-die L2 Cache & 533MHz FSB 1.
Specifications Feature Specification C Video Adapter Intel 945GMS Integration Intel® Graphics Media Accelerator 950 (Intel® GMA 950) Dynamic Video Memory Technology DVMT 3.0 - Supports up to 128MB of Video Memory (dynamically allocated from system memory where needed) Supports DualView™ Storage Optional Device Drive Bay Options: One Changeable 9.5mm(h) Optical Device (CD/DVD) Type Drive (see “Optional” on page C - 5 for drive options) Hard Disk Bay: Easy Changeable 2.5" OR 1.8", 9.
Specifications C Feature Communication Specification AZALIA 56K Fax Modem - V.90 & V.92 Compliant 10/100M Fast Ethernet LAN Intel PRO/Wireless 3945ABG PCIe Interface Wireless LAN Module (Option) USB (2.0) Bluetooth Module (Option) Power Management Supports ACPI 2.0 and APM v 1.2 Supports Wake On Modem Ring Supports Wake On LAN Power Full Range AC/DC Adapter - AC Input 100 ~ 240V, 50 ~ 60Hz / DC Output 18.5V, 3.5A 4 Cell Smart Lithium-Ion Battery Pack, 5200mAH, 38.
Specifications Feature Optional Specification Optical Device Module Options: Dummy ODD DVD-ROM Drive Module DVD/CD-RW Combo Drive Module DVD Dual - Supporting Super MULTI Drive Module C Intel PRO/Wireless 3945ABG PCIe Interface Wireless LAN Module (Option) 10 Cell Smart Lithium-Ion Battery Pack, 13000mAH, 96.2W USB (2.
Specifications C C - 6
