Preface Notice The company reserves the right to revise this publication or to change its contents without notice. Information contained herein is for reference only and does not constitute a commitment on the part of the manufacturer or any subsequent vendor. They assume no responsibility or liability for any errors or inaccuracies that may appear in this publication nor are they in anyway responsible for any loss or damage resulting from the use (or misuse) of this publication.
Preface R&TTE Directive This device is in compliance with the essential requirements and other relevant provisions of the R&TTE Directive 1999/5/EC. This device will be sold in the following EEA countries: Austria, Italy, Belgium, Liechtenstein, Denmark, Luxembourg, Finland, Netherlands, France, Norway, Germany, Portugal, Greece, Spain, Iceland, Sweden, Ireland, United Kingdom, Cyprus, Czech Republic, Estonia, Hungary, Latvia, Lithuania, Malta, Slovakia, Poland, Slovenia.
Preface CE Marking This device has been tested to and conforms to the regulatory requirements of the European Union and has attained CE Marking. The CE Mark is a conformity marking consisting of the letters “CE”. The CE Mark applies to products regulated by certain European health, safety and environmental protection legislation. The CE Mark is obligatory for products it applies to: the manufacturer affixes the marking in order to be allowed to sell his product in the European market.
Preface FCC Statement (Federal Communications Commission) You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Preface FCC RF Radiation Exposure Statement: 1. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. Warning Use only shielded cables to connect I/O devices to this equipment.
Preface IMPORTANT SAFETY INSTRUCTIONS Follow basic safety precautions, including those listed below, to reduce the risk of fire, electric shock, and injury to persons when using any electrical equipment: 1. 2. 3. 4. 5. Do not use this product near water, for example near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool. Avoid using this equipment with a telephone line (other than a cordless type) during an electrical storm.
Preface Instructions for Care and Operation The notebook computer is quite rugged, but it can be damaged. To prevent this, follow these suggestions: 1. Don’t drop it, or expose it to shock. If the computer falls, the case and the components could be damaged. Do not expose the computer to any shock or vibration. 2. Do not place it on an unstable surface. Do not place anything heavy on the computer. Keep it dry, and don’t overheat it.
Preface 3. Avoid interference. Keep the computer away from high capacity transformers, electric motors, and other strong magnetic fields. These can hinder proper performance and damage your data. 4. Follow the proper working procedures for the computer. Shut the computer down properly and don’t forget to save your work. Remember to periodically save your data as data may be lost if the battery is depleted. Do not turn off the power until you properly shut down all programs. 5.
Preface Power Safety The computer has specific power requirements: • Only use a power adapter approved for use with this computer. • Your AC/DC adapter may be designed for international travel but it still requires a steady, uninterrupted power supply. If you are unsure of your local power specifications, consult your service representative or local power company. • The power adapter may have either a 2-prong or a 3-prong grounded plug.
Preface Polymer Battery Precautions Note the following information which is specific to polymer batteries only, and where applicable, this overrides the general battery precaution information overleaf. • Polymer batteries may experience a slight expansion or swelling, however this is part of the battery’s safety mechanism and is not a cause for concern. • Use proper handling procedures when using polymer batteries.
Preface General Battery Precautions • Only use batteries designed for this computer. The wrong battery type may explode, leak or damage the computer. • Do not remove any batteries from the computer while it is powered on. • Do not continue to use a battery that has been dropped, or that appears damaged (e.g. bent or twisted) in any way. Even if the computer continues to work with a damaged battery in place, it may cause circuit damage, which may possibly result in fire.
Preface Cleaning Do not apply cleaner directly to the computer; use a soft clean cloth. Do not use volatile (petroleum distillates) or abrasive cleaners on any part of the computer. Servicing Do not attempt to service the computer yourself. Doing so may violate your warranty and expose you and the computer to electric shock. Refer all servicing to authorized service personnel. Unplug the computer from the power supply.
Preface Travel Considerations Packing As you get ready for your trip, run through this list to make sure the system is ready to go: 1. 2. 3. 4. 5. 6. 7. 8. Check that the battery pack and any spares are fully charged. Power off the computer and peripherals. Close the display panel and make sure it’s latched. Disconnect the AC/DC adapter and cables. Stow them in the carrying bag. The AC/DC adapter uses voltages from 100 to 240 volts so you won’t need a second voltage adapter.
Preface On the Road In addition to the general safety and maintenance suggestions in this preface, and Chapter 8: Troubleshooting, keep these points in mind: Hand-carry the notebook - For security, don’t let it out of your sight. In some areas, computer theft is very common. Don’t check it with “normal” luggage. Baggage handlers may not be sufficiently careful. Avoid knocking the computer against hard objects.
Preface Developing Good Work Habits Developing good work habits is important if you need to work in front of the computer for long periods of time. Improper work habits can result in discomfort or serious injury from repetitive strain to your hands, wrists or other joints. The following are some tips to reduce the strain: • Adjust the height of the chair and/or desk so that the keyboard is at or slightly below the level of your elbow. Keep your forearms, wrists, and hands in a relaxed position.
Preface Lighting Proper lighting and a comfortable viewing angle can reduce eye strain and shoulder and neck muscle fatigue. • • • • Position the display to avoid glare or reflections from overhead lighting or outside sources of light. Keep the display screen clean and set the brightness and contrast to levels that allow you to see the screen clearly. Position the display directly in front of you at a comfortable viewing distance. Adjust the display-viewing angle to find the best position.
Preface Contents Notice .............................................................................................................................................................I EuP-Standby and Off Mode Power Consumption Statement: ..................................................................... II FCC Statement ............................................................................................................................................IV FCC RF Radiation Exposure Statement: .......
Preface LCD Panel Open - Models A & C .............................................................................................................1-7 LCD Panel Open - Model B ......................................................................................................................1-8 LCD Panel Open - Model D ......................................................................................................................1-9 LCD Panel Open - Model E ..........................................
Preface Windows 8 Charms Bar ...........................................................................................................................1-34 Windows 8 Control Panel ........................................................................................................................1-36 Windows 8 Taskbar .................................................................................................................................1-39 Video Features .......................................
Preface Gestures and Device Settings ..................................................................................................................2-14 Touchpad Configuration for Model B .....................................................................................................2-18 Finger Sensing Pad Configurator .............................................................................................................2-19 Power Management Overview ..........................................
Preface New Battery .............................................................................................................................................3-15 Recharging the Battery with the AC/DC Adapter ...................................................................................3-15 Proper handling of the Battery Pack ........................................................................................................3-16 Battery FAQ .......................................................
Preface MEI Driver .................................................................................................................................................4-7 Audio .........................................................................................................................................................4-7 Windows Experience Index .......................................................................................................................4-8 Optional Drivers ................
Preface Intel Anti-Theft Technology (Advanced Menu) ........................................................................................5-9 SATA Mode (Advanced Menu) ................................................................................................................5-9 Boot Logo (Advanced Menu) ..................................................................................................................5-10 Power On Boot Beep (Advanced Menu) ..............................................
Preface Upgrading the Optical Device (Models A/C) ............................................................................................6-7 Upgrading the Optical Device (Model B) .................................................................................................6-8 Upgrading the Optical Device (Models D & E) ........................................................................................6-9 Upgrading the Hard Disk Drive(s) .........................................................
Preface AHCI Mode ...............................................................................................................................................7-2 RAID ..........................................................................................................................................................7-2 Intel® Rapid Storage Technology Application .........................................................................................7-2 SATA RAID Setup Procedure (Windows 8) .........
Preface IRST Driver Installation ..........................................................................................................................7-45 Intel® Rapid Storage Technology for RAID Systems ............................................................................7-46 RAID Volume Data Verification and Repair ..........................................................................................7-48 Replacing and Reverting Recovery and Master Volumes ..................................
Preface Ports and Jacks ..........................................................................................................................................A-2 Card Reader ..............................................................................................................................................A-2 DC-In Jack ................................................................................................................................................A-2 DisplayPort / ...............
Preface Brightness .................................................................................................................................................B-3 Volume .....................................................................................................................................................B-3 Power Conservation ..................................................................................................................................B-3 Sleep .........................
Preface Optimus™ Customization Options .........................................................................................................C-28 Set PhysX® Configuration .....................................................................................................................C-32 Video Settings .........................................................................................................................................C-33 HDMI Audio Configuration ..................................
Preface Features .....................................................................................................................................................D-5 Power Management ..................................................................................................................................D-5 Power ........................................................................................................................................................D-5 Environmental Spec ..........
Quick Start Guide Chapter 1: Quick Start Guide Overview This Quick Start Guide is a brief introduction to the basic features of your computer, to navigating around the computer and to getting your system started. The remainder of the manual covers the following: • Chapter 2 • Chapter 3 • Chapter 4 • Chapter 5 • Chapter 6 • Chapter 7 • Chapter 8 • Appendix A • Appendix B • Appendix C • Appendix D A guide to using some of the main features of the computer e.g.
1 Quick Start Guide Advanced Users If you are an advanced user you may skip over most of this Quick Start Guide. However you may find it useful to refer to “Drivers & Utilities” on page 4 - 1, “BIOS Utilities” on page 5 - 1 and “Upgrading The Computer” on page 6 - 1 in the User’s Manual. You may also find the notes marked with a of interest to you. Notes Check the light colored boxes with the mark above to find detailed information about the computer’s features.
Quick Start Guide Not Included Operating Systems (e.g. Windows 8) and applications (e.g. word processing, spreadsheet and database programs) have their own manuals, so please consult the appropriate manuals. Drivers If you are installing new system software, or are re-configuring your computer for a different system, you will need to install the appropriate drivers. Drivers are programs which act as an interface between the computer and a hardware component e.g. a wireless network module.
1 Quick Start Guide System Software Your computer may already come with system software pre-installed. Where this is not the case, or where you are re-configuring your computer for a different system, you will find the Windows 8 operating system is supported. Note: In order to run Windows 8 without limitations or decreased performance, your computer requires a minimum 1GB of system memory (RAM).
Quick Start Guide Model Differences This notebook series includes five different model types that mainly differ as indicated in the table below. Note that your model may appear slightly different from those pictured in this manual. Feature Model A 15.6" (39.62cm) FHD (1920 * 1080) 16:9 Backlit Panel Video Adapters Supported Keyboard LED Illuminated Touchpad Model D Model E 17.3" (43.
1 Quick Start Guide System Startup 1. Remove all packing materials, and place the computer on a stable surface. 2. Securely attach any peripherals you want to use with the notebook (e.g. keyboard and mouse) to their ports. 3. Attach the AC/DC adapter to the DC-In jack at the rear of the computer, then plug the AC power cord into an outlet, and connect the AC power cord to the AC/DC adapter. 4.
Quick Start Guide LCD Panel Open - Models A & C 2 1 Figure 1 - 2 LCD Panel Open Models A & C 3 1. 2. 3. 4. 5. 6. 7. 8. 9. 4 7 6 5 5 9 10 11 8 Note that the Touchpad and Buttons has a valid operational area indicated within the red dotted lines above. Built-In PC Camera PC Camera LED Built-In Microphone LCD Speakers Power Button LED Lock Indicators LED Status Indicators Keyboard (Model A supports an Illuminated Keyboard) 10. TouchPad and Buttons 11.
1 Quick Start Guide Figure 1 - 3 LCD Panel Open Model B LCD Panel Open - Model B Built-In PC Camera PC Camera LED Built-In Microphone LCD Speakers Power Button LED Indicators Illuminated Keyboard Illuminated TouchPad and Buttons 10. Fingerprint Reader (Optional) 2 1 1. 2. 3. 4. 5. 6. 7. 8. 9. Note that the Illuminated Touchpad has a defined valid operational area of sensitivity indicated within the sensor area of the illustration below. See “Illuminated Touchpad Sensitivity” on page 2 - 12.
Quick Start Guide LCD Panel Open - Model D 2 Figure 1 - 4 LCD Panel Open Model D 3 1 1. 2. 3. 4. 5. 6. 7. 8. 9. 4 5 5 6 7 Note that the Touchpad and Buttons has a valid operational area indicated within the red dotted lines above. Built-In PC Camera PC Camera LED Built-In Microphone LCD Speakers LED Indicators Power Button Illuminated Keyboard TouchPad and Buttons 10.
1 Quick Start Guide Figure 1 - 5 LCD Panel Open Model E LCD Panel Open - Model E Built-In PC Camera PC Camera LED Built-In Microphone LCD Speakers LED Indicators Power Button Illuminated Keyboard TouchPad and Buttons 10. Fingerprint Reader (Optional) 2 1 1. 2. 3. 4. 5. 6. 7. 8. 9. Note that the Illuminated Touchpad has a defined valid operational area of sensitivity indicated within the sensor area of the illustration below. See “Illuminated Touchpad Sensitivity” on page 2 - 12.
Quick Start Guide LED Indicators The LED indicators display helpful information about the current status of the computer.
1 Quick Start Guide Other Keyboards If your keyboard is damaged or you just want to make a change, you can use any standard USB keyboard. The system will detect and enable it automatically. However special functions/hot-keys unique to the system’s regular keyboard may not work. Num Lk & Scr Lk Hold down the Fn Key and Scr Lk/Num Lk to enable scroll lock/number lock, and check the LED indicator for status.
Quick Start Guide Keyboard LED - Models A, B, D & E 2 key to toggle the keyboard LED on/off. The keyboard LED may be configured using Press Fn plus the 1 key to launch the the Fn + key combination outlined in the table below. In addition press Fn plus the keyboard backlight application to configure the settings (see overleaf).
Quick Start Guide 1 Keyboard Backlight Application (Models A, B. D & E) The keyboard Backlight application can be accessed by pressing the Fn plus in the application to display the configuration keys. • • • • key. Click the Help button Click the Custom button to display the three sections of the keyboard which may be configured. Click a section of the keyboard and the color buttons will be displayed.
Quick Start Guide Effects Buttons & Help (Models A, B, D & E) LED Effects Buttons Random Color Up/Down Wave Dancing Effect Breathing (All Colors) Tempo Beat Cycle (Colors as Selected in RGB) Flashing Custom Mode - Display & Configure Keyboard Sections & Colors Illumination Keys Note that the keyboard illumination (increase/decrease) keys may be used to configure the keyboard LED in Custom Mode only.
1 Quick Start Guide Other Keyboards If your keyboard is damaged or you just want to make a change, you can use any standard USB keyboard. The system will detect and enable it automatically. However special functions/hot-keys unique to the system’s regular keyboard may not work. Keyboard - Model C The keyboard has an embedded numerical keypad for easy numeric data input, and features function keys to allow you to change operational features instantly.
Quick Start Guide Keyboard Shortcuts The following Windows Logo Key (Winkey) keyboard shortcuts are useful for navigation/operation in Windows 8.
1 Quick Start Guide Function Keys & Visual Indicators The function keys (F1 - F12 etc.) will act as hot keys when pressed while the Fn key is held down. Visual indicators (see the table below) are available when the Hot Key driver is installed.
Quick Start Guide Control Center When in the Windows Desktop application (not in the Start screen) press the Fn + Esc key combination, or double-click the icon in the notification area of the taskbar to toggle the Control Center on/off. The Control Center gives quick access to frequently used controls and enables you to quickly turn the camera/Touch Pad on/off (see Appendix B for full details). Control Center Click on any button to turn any of the modules (e.g. TouchPad, Camera) on/off.
1 Quick Start Guide Figure 1 - 10 Front & Rear Views Models A, B & C Front & Rear Views (Models A, B & C) Models A & C 1 1. LED Power Indicators 2. Vent/Fan Intake 3. Display Port 4. HDMI-Out Port 5. Mini Display Port 6. DC-In Jack Models A & C 3 2 4 5 2 6 Model B 1 Model B 2 3 4 5 6 2 HDMI Port Note that the HDMI Port supports video and audio signals to attached external displays (see “HDMI Audio Configuration” on page C - 34).
Quick Start Guide Front & Rear Views (Models D & E) Figure 1 - 11 Front & Rear Views Models D & E Model D 1 Model D 2 7 3 5 4 2 6 Model E 1 1. LED Power Indicators 2. Vent/Fan Intake 3. Display Port 4. HDMI-Out Port 5. Mini Display Port 6. DC-In Jack 7. Security Lock Slot Model E 7 2 3 4 5 2 6 HDMI Port Note that the HDMI Port supports video and audio signals to attached external displays (see “HDMI Audio Configuration” on page C - 34).
1 Quick Start Guide Figure 1 - 12 Right View 1. Optical Device Drive Bay 2. Headphone Jack 3. Microphone Jack 4. S/PDIF-Out Jack 5. Line-In Jack 6. 1 * USB 2.0 Port 7. Security Lock Slot (Models A, B & C Only) Right View Models A & C 1 1 1 - 22 Right View 4 5 7 6 2 3 4 5 7 6 Model D 2 1 Note that the connections to the USB ports only fit one way, do not force them. USB 3.0 ports are denoted by their blue color; USB 2.0 ports are colored black.
Quick Start Guide Left View Figure 1 - 13 Left View Models A & C 2 1 6 5 4 3 Model B 1 2 6 5 4 3 Model D 2 1 3 4 5 6 Mini-IEEE 1394a Port Model E 1 2 3 4 1. Mini-IEEE 1394a Port 2. RJ-45 LAN Jack 3. 1 * Powered USB 3.0 Port 4. 1 * USB 3.0 Port 5. Combined eSATA/ USB 3.0 Port 6. Multi-in-1 Card Reader 5 6 The Mini-IEEE 1394a port only supports SELF POWERED IEEE 1394 devices.
1 Quick Start Guide USB 3.0 Ports & Powered USB 2.0 Port USB 3.0 ports are denoted by their blue color; USB 2.0 ports are colored black. Note that the USB 3.0 port is not operational under DOS and does not support wake on USB. The powered USB 3.
Quick Start Guide Bottom View - Models A & C 3 Figure 1 - 14 Bottom View 1. Sub Woofer 2. Fan Outlet/Intake 3. Component Bay Cover 4. HDD Bay 5. Battery 2 2 2 1 2 4 5 Overheating Battery Information Always completely discharge, then fully charge, a new battery before using it. Completely discharge and charge the battery at least once every 30 days or after about 20 partial discharges. See “Battery Information” on page 3 - 13 for full instructions.
1 Quick Start Guide Figure 1 - 15 Bottom View Bottom View - Model B 1. Sub Woofer 2. Fan Outlet/Intake 3. Component Bay Cover 4. HDD/ODD Bay 5. Battery 3 2 1 2 2 2 2 4 5 Overheating To prevent your computer from overheating make sure nothing blocks the vent(s)/fan intake(s) while the computer is in use. Battery Information Always completely discharge, then fully charge, a new battery before using it.
Quick Start Guide Bottom View - Model D 1 2 Figure 1 - 16 Bottom View 1. Sub Woofer 2. Fan Outlet/Intake 3. Component Bay Cover 4. Primary HDD Bay 5. Secondary HDD Bay 6. Battery 2 2 3 2 4 6 5 Overheating Battery Information Always completely discharge, then fully charge, a new battery before using it. Completely discharge and charge the battery at least once every 30 days or after about 20 partial discharges. See “Battery Information” on page 3 - 13 for full instructions.
1 Quick Start Guide Figure 1 - 17 Bottom View Bottom View - Model E 1. Sub Woofer 2. Fan Outlet/Intake 3. Component Bay Cover 4. Primary HDD Bay 5. Secondary HDD Bay 6. Battery 1 2 2 3 2 2 4 6 5 Overheating To prevent your computer from overheating make sure nothing blocks the vent(s)/fan intake(s) while the computer is in use. Battery Information Always completely discharge, then fully charge, a new battery before using it.
Quick Start Guide Windows Control Panel Throughout this manual you will see an instruction to open the Control Panel. In Windows 8 right-click the lower left hot corner to bring up the context menu (or use the Windows Logo Key + X key combination) and select Control Panel. Swipe a finger from the right of the Touchpad from the Desktop (not the Start screen) to access the Charms Bar, click Settings and click Control Panel. Move the mouse to the bottom left of the screen and right-click to access the menu.
1 Quick Start Guide Windows 8 Start Screen & Desktop The Apps, control panels, utilities and programs within Windows 8 are accessed from the Start screen and/or Windows Desktop app. The Desktop (which runs as an app within the Start screen) can be accessed by clicking the Desktop item in the Start screen (or by using the Windows Logo Key + D key combination).
Quick Start Guide Apps & Tiles The Windows 8 Start screen will contain a number of apps, and many more will be installed as you add more applications etc. Not all of these apps can fit on one screen so you will often need use the slider at the bottom of the screen in order to view all the necessary Apps. Accessing Pining/Unpinning All Apps You can add and remove the tiles for apps and control panels in the Start screen. Right-click on a blank area of the Start screen, and you will see the All Apps icon.
1 Quick Start Guide Desktop Application When the Desktop app is running (click the app in the Start screen or use the Windows Logo Key + D key combination) you can use lower left hot corner to switch between the Start screen and the Windows Desktop app. To do so move your mouse to hover over the bottom left corner of the screen and click the pop-up. When you move to the lower left hot corner in the Start screen itself it will take you back to your most recently used app.
Quick Start Guide When the Desktop app is running you can right-click the lower left hot corner (or use the Windows Logo Key + X key combination) to bring up an advanced context menu of useful features such as Control Panel, Programs and Features, Power Options, Task Manager, Search, Windows Explorer, Command Prompt, Device Manager and Network Connections etc.
1 Quick Start Guide Windows 8 Charms Bar The right side of the screen displays the Windows 8 Charms Bar. The Charms Bar contains the Search, Share, Start, Devices and Settings menus. To access up the Charms Bar move the cursor to the upper or lower right corners of the screen, and then hover over one of the items in the Charms Bar to activate it (the bar will be black when it is active), or use the Windows Logo Key + C key combination.
Quick Start Guide Charms Bar Items • Search results. • Share : You can search for any file, application, Apps and control panel settings with instantaneous : This button is used to share information with people via mail or social networks. • Start : Click to bring up the Start Menu (the same function as pressing the Windows Logo Key or clicking the bottom left of the screen). • Devices : Click this button to change connected peripheral device settings e.g. an external display.
1 Quick Start Guide Windows 8 Control Panel In many instances throughout this manual you will see an instruction to open the Control Panel. The Control Panel can be accessed in a number of ways in Windows 8. • Click/ Search in the Windows Charms Bar (see previous page) and the search pane will pop out. Type Control Panel and select it from the results to the left.
Quick Start Guide • When in the Desktop app (this does not apply to the Start screen) click on Settings in the Windows Charms Bar and select Control Panel from the menu. Figure 1 - 27 - Settings Charms Bar (Desktop App Only) • Right-click on a blank area of the Start screen, or swipe a finger from the top or bottom of the touch screen. Click the All Apps icon and click Control Panel.
1 Quick Start Guide • Right-click the lower left hot corner to bring up the menu and select Control Panel (see Figure 1 - 22 on page 1 - 33). Keyboard Shortcut to Control Panel You can also use keyboard shortcuts to access the Control Panel. Press the Windows logo key and X to bring up the context menu, and then press P to bring up the Control Panel. Alternatively press the Windows logo key and R to bring up the Run dialog box, and then type “Control Panel” and press Enter to access the Control Panel.
Quick Start Guide Windows 8 Taskbar In many instances throughout this manual you will see an instruction to access the notification area of the taskbar. In Windows 8 the taskbar is accessed from the Desktop application. If you are in the Start screen you will need to click the Desktop app to switch to the Desktop. The taskbar is displayed at the bottom of the desktop screen, and you can see the notification area of the taskbar in the bottom right of the screen.
1 Quick Start Guide Video Features You can switch display devices, and configure display options, from the Display control panel (in Appearances and Personalization) in Windows 8 when running the Desktop app (see “Desktop Application” on page 1 32). NVIDIA® Optimus™ Technology NVIDIA® Optimus™ technology is a seamless technology designed to get best performance from the graphics system while allowing longer battery life, without having to manually change settings.
Quick Start Guide To access Display (Control Panel) and Screen Resolution in Windows 8: 1. 2. 3. Go to the Control Panel. Click Display (icon) - In the Appearance and Personalization category. Adjust resolution. Right-Click Desktop App 2 1 3 1. You can right-click the desktop and select Screen resolution 1 (Figure 1 - 30). 2. Use the dropbox to select the screen Resolution 2 (Figure 1 - 30). 3. Click Advanced settings 3 (Figure 1 30) to bring up the Advanced properties tabs.
1 Quick Start Guide To access the Intel(R) Graphics Control Panel: 1. 2. Click Advanced settings 3 (Figure 1 - 30 on page 1 - 41) in the Screen Resolution control panel in Windows. Click the Intel(R)... tab and click Graphics Properties (button) 4 (Figure 1 - 31 on page 1 - 42) . OR 3. Right-click the desktop and select Graphics Properties from the menu. OR 4. Click the icon in the notification area of the Desktop taskbar and select Graphics Properties from the menu.
Quick Start Guide To access the NVIDIA Control Panel: 1. Right-click the desktop and select NVIDIA Control Panel 5 (Figure 1 - 32). OR 2. Double-click the icon 6 (Figure 1 - 32) in the Windows control panel.
1 Quick Start Guide Configuring External Displays In Windows 8 it is possible to quickly configure external displays from the Devices menu item in the Charms Bar (see “Windows 8 Charms Bar” on page 1 - 34). To Configure External Displays from Devices (Charms Bar): 1. 2. 3. 4. Attach your display to the appropriate port, and turn it on. Go the Charms Bar and select Devices. Click Second Screen. Click on any one of the options from the menu to select Duplicate, Extend or a Single display.
Quick Start Guide Power Options Power Options (Hardware and Sound) can be accessed from the Control Panel. The Power Menu item in Settings in the Charms Bar in Windows 8 may be used to Shut down or Restart (you can also add Hibernate/ Sleep to the menu - see “Adding Hibernate/Sleep to the Power Menu” on page 3 - 9). Shut Down, Restart or Sleep 1. 2. 3. Go to the Charms Bar and click Settings. Click Power . Select Sleep, Shut Down or Restart.
1 Quick Start Guide Running Apps To run apps in Windows 8 you will need to check that the Screen Resolution and User Account Control Settings are compatible with the system requirements. Screen Resolution Settings 1. 2. Switch to the Windows Desktop (click the app or use the Windows logo key + D key combination). Right-click a blank area of the Windows Desktop and select Screen Resolution.
Quick Start Guide User Account Control Settings If your computer meets the minimum screen resolution requirements, and still you can't run Metro apps, then that you have to check the status of User Account Control (UAC). Metro apps may fail to open when the UAC is turned off. To check whether the UAC is on or off, follow the instructions below. 1. 2. 3. 4. Open the Control Panel.
1 Quick Start Guide 1 - 48
Storage Devices, Mouse, & Audio Chapter 2: Storage Devices, Mouse, & Audio Overview Read this chapter to learn more about the following main features and components of the computer: • • • • • Hard Disk Drive Optical Device Multi-in-1 Card Reader Audio Features Touchpad and Buttons/Mouse Overview 2 - 1 2
Storage Devices, Mouse, & Audio 2 Power Safety Before attempting to access any of the internal components of your computer please ensure that the machine is not connected to the AC power, and that the machine is turned off. Also ensure that all peripheral cables, including phone lines, are disconnected from the computer. Hard Disk Drive The hard disk drive(s) is used to store your data in the computer. The hard disks) can be taken out to accommodate other 2.
Storage Devices, Mouse, & Audio Optical Device There is a bay for a 5.25" optical (CD/DVD) device (12.7mm height). The actual device will depend on the model you purchased (see “Storage” on page D - 3). The optical device is usually labeled “Drive D:” and may be used as a boot device if properly set in the BIOS (see “Boot Menu” on page 5 - 14).
Storage Devices, Mouse, & Audio 2 Handling CDs or DVDs CD Emergency Eject If you need to manually eject a CD (e.g. due to an unexpected power interruption) you may push the end of a straightened paper clip into the emergency eject hole. However please do NOT use a sharpened pencil or similar object that may break and become lodged in the hole. Disk Eject Warning Don’t try to remove a CD/DVD while the system is accessing it. This may cause the system to “crash”.
Storage Devices, Mouse, & Audio DVD Regional Codes To change the DVD regional codes: 1. 2. 3. Go to the Control Panel Double-click Device Manager (Hardware and Sound), then click the + next to DVD/CD-ROM drives. Double-click on the DVD-ROM device to bring up the Properties dialog box, and select the DVD Region (tab) to bring up the control panel to allow you to adjust the regional code.
Storage Devices, Mouse, & Audio 2 Card Reader Cover Make sure you keep the cover in the card reader when not in use. This will help prevent foreign objects and/or dust getting in to the card reader. Push-Push Card Reader Multi-in-1 Card Reader The card reader allows you to use some of the latest digital storage cards. Push the card into the slot and it will appear as a removable device, and can be accessed in the same way as your hard disk (s).
Storage Devices, Mouse, & Audio Audio Features You can configure the audio options on your computer from the Sound control panel in Windows, or from the Realtek HD Audio Manager icon in the notification area/control panel (right-click the notification area icon to bring up an audio menu). The volume may also be adjusted by means of the Fn + F5/F6 key combination (see Table 1 - 6, on page 1 - 18).
Storage Devices, Mouse, & Audio Setup for Audio Recording 2 To record audio sources on your computer at optimum quality follow the instructions below: 1. 2. 3. 4. Figure 2 - 6 Realtek Audio Manager Recording Setup 2 - 8 Audio Features Click Control Panel and make sure you are in Classic View. Click Realtek HD Audio Manager (or right-click the notification area icon and select Sound Manager).
Storage Devices, Mouse, & Audio Setup for 5.1 or 7.1 Surround Sound To setup your system for 5.1 or 7.1 surround sound you will need to connect the audio cables to the Headphone-Out, Line-In, Microphone-In jack and S/PDIF-Out jacks (note: the S/PDIF jack is used for 7.1 surround sound only). 1. 2. 3. 4. Click Start, and click Control Panel (or point to Settings and click Control Panel) and make sure you are in Classic View.
Storage Devices, Mouse, & Audio 5. 6. 2 Plug the front speaker cables into the Headphone-Out Jack. Plug in the other cables (you may require an adapter to connect each cable to the appropriate jack e.g a stereo mini to dual RCA adapter) from your speakers as follows: • Line-In Jack = Rear Speaker Out • Microphone-In Jack = Center/Subwoofer Speaker Out • S/PDIF-Out Jack = Side Speaker Out (for 7.1 Surround Sound Only) 7. 8. 9.
Storage Devices, Mouse, & Audio Touchpad and Buttons/Mouse The Touchpad is an alternative to the mouse; however, you can also add a mouse to your computer through one of the USB ports. The Touchpad buttons function in much the same way as a two-button mouse. The Touchpad driver installed on your system will be dependent on your computer model. See overleaf for Touchpad sensitivity information, and see the pages indicated below for configuration information.
Storage Devices, Mouse, & Audio 2 Standard Touchpad Sensitivity The standard Touchpad (featured in Model A, C & D computers) also have a valid operational area is that indicated within the red dotted lines above.
Storage Devices, Mouse, & Audio Touchpad Configuration for Models A, C, D & E Once you have installed the TouchPad driver (see “TouchPad” on page 4 - 6) you can configure the functions from the Mouse control panel in Windows, or by doubleclicking the TouchPad driver icon in the notification area of the taskbar in the Desktop app. You may then configure the TouchPad tapping, buttons, scrolling, pointer motion and sensitivity options to your preferences. You will find further information at www.synaptics.
Storage Devices, Mouse, & Audio 2 Show Video You can get a clearer view of the gestures involved by clicking the Show Video option for each gesture item. Select the gesture (Pinch Zoom, Rotating, Three Fingers Down and Three Finger Flick) in the Device Settings > Settings left tree menu and click the Show Video button to see the demonstration video.
Storage Devices, Mouse, & Audio Disabling the Touchpad If you need to disable the Touchpad for any reason (e.g. you may find that when using the computer’s internal keyboard you accidentally trigger the Touchpad when resting your wrists or palms on it) you can do so by using Fn + F1 key combination. 2 You can also set the system to automatically disable the internal Touchpad when an external USB point device (e.g a USB mouse) is attached. 1. 2. 3. 4. Go to the Mouse Properties control panel.
Storage Devices, Mouse, & Audio Scrolling The Two-Finger scrolling feature works in most scrollable windows and allows you to scroll horizontally and vertically. Place two fingers, slightly separated, on the TouchPad surface and slide both fingers in the direction required (in a straight continuous motion). 2 Figure 2 - 13 Scrolling Gesture Zooming The Pinch Zoom gesture can be used to perform the same function as a scroll wheel in Windows applications that support CTRL + scroll wheel zoom functionality.
Storage Devices, Mouse, & Audio Rotating Use the Pivot Rotate gesture to rotate objects (e.g. photos) in 90 degree increments. Place a finger down on the left “target” zone and keep it stationary. Place another finger near the middle of the TouchPad and slide it in a circular motion around the stationary finger (clockwise or counterclockwise) to rotate the object.
Storage Devices, Mouse, & Audio 2 Tray Icon Make sure that the Touchpad driver icon in the notification area of the Desktop taskbar. Touchpad Configuration for Model B Once you have installed the Touchpad driver (see “TouchPad” on page 4 - 6) you can configure the functions by double-clicking the Touchpad driver icon in the notification area of the Desktop taskbar, or from the Mouse control panel in Windows.
Storage Devices, Mouse, & Audio Finger Sensing Pad Configurator The Finger Sensing Pad Configurator allows you to use a configure the settings for the Finger Sensing Pad device and software. The left pane in the control panel contains all the configurable items, and you can click the “+” to expand the menu selections. 1. 2. 3. 4. Go to the Control Panel. Click Mouse (Hardware and Sound). Click Finger Sensing Pad (tab) and click Configure.
Storage Devices, Mouse, & Audio Disabling the Touchpad If you need to disable the Touchpad for any reason (e.g. you may find that when using the computer’s internal keyboard you accidentally trigger the Touchpad when resting your wrists or palms on it) you can do so by using Fn + F1 key combination. 2 You can also set the system to automatically disable the internal Touchpad when an external USB pointing device (e.g. a USB mouse) is attached, or while you are typing (see over). 1. 2. 3.
Storage Devices, Mouse, & Audio You can also enable Typing Detection to disable the pad while you are typing. The pad will be disabled while typing is detected, and will be reactivated after a set interval of time when typing is not detected. You can use the slider to adjust the reactivation time for an appropriate interval.
Storage Devices, Mouse, & Audio 2 Traditional or Reverse Scrolling With traditional scrolling, when you want to scroll up a web page, you put fingers on the pad and them move upwards. When you want to scroll down, you move your fingers down. On-pad Functions Put a tick in the appropriate box to enable the function. • On-pad Click - The same function as a left mouse click. • Vertical/Horizontal Scrolling - This will enable sensing zones on the pad to allow you to touch to enable scrolling.
Storage Devices, Mouse, & Audio Gestures Click Gestures and make sure that the Enable Gestures tickbox is clicked. Doubleclick Gestures and then double-click Tailor-made or Applications to open the submenu. You can enable/disable and configure any of the Tailor-made gestures from these submenus. Play Video You can get a clearer view of the gestures involved by clicking the Play Video option for each gesture item.
Storage Devices, Mouse, & Audio • Two Fingers Straight Up/Down - Place two fingers side by side on the pad, slightly apart. Slide the fingers upwards/downwards in a continuous motion. 2 Figure 2 - 23 2F Straight Up/ Down • Two Fingers Straight Right/Left - Place two fingers side by side on the pad, slightly apart. Slide the fingers right/left in a continuous motion. Figure 2 - 24 2F Straight Right/ Left • Two Fingers Zoom In/Out - Place two fingers side by side on the pad, slightly apart.
Storage Devices, Mouse, & Audio • Two Fingers Click - Tap the pad with two slightly separated fingers. This simulates the use of a middle mouse button often used in the most common internet browsers. 2 Figure 2 - 26 2F Click • One Finger Edge Swipe Top - Place a single finger on the top edge of the pad and slide the finger downwards onto the pad. This is used to open the App bar in the Windows Start menu (not the desktop).
Storage Devices, Mouse, & Audio • One Finger Edge Swipe Right - Place a single finger on the right edge of the pad and slide the finger to the left onto the pad. This is used to open the Charms bar. 2 Figure 2 - 28 1F Edge Swipe Right • One Finger Edge Swipe Left - Place a single finger on the left edge of the pad and slide the finger to the right onto the pad. This is used to switch to the last used application.
Storage Devices, Mouse, & Audio Applications A number of programs/applications support gestures which trigger functions within the program. The Program List displays the programs/applications supporting these functions, and you can use the scroll bar to the right to scroll up/down the list. Click to select the program/application and click View (or just double-click) to see the gestures supported.
Storage Devices, Mouse, & Audio 2 2 - 28
Power Management Chapter 3: Power Management Overview To conserve power, especially when using the battery, your computer power management conserves power by controlling individual components of the computer (the monitor and hard disk drive) or the whole system.
Power Management 3 Forced Off If the system “hangs”, and the Ctrl + Alt + Del key combination doesn’t work, press the power button for 4 seconds, or longer, to force the system to turn itself off. The Power Sources The computer can be powered by either an AC/DC adapter or a battery pack. AC/DC Adapter Use only the AC/DC adapter that comes with your computer. The wrong type of AC/ DC adapter will damage the computer and its components. 1. 2. 3. 4.
Power Management Turning On the Computer Now you are ready to begin using your computer. To turn it on simply press the power button on the front panel. When the computer is on, you can use the power button as a Stand by/Hibernate/ Shutdown hot-key button when it is pressed for less than 4 seconds (pressing and holding the power button for longer than this will shut the computer down). Use Power Options (Hardware and Sound) in the Windows control panel to configure this feature.
Power Management 3 Resuming Operation See Table 3 - 1, on page 3 - 10 for information on how to resume from a power-saving state. Password It is recommended that you enable a password on system resume in order to protect your data. Figure 3 - 2 Power Plan Advanced Settings 3 - 4 Power Plans Power Plans The computer can be configured to conserve power by means of power plans. You can use (or modify) an existing power plan, or create a new one.
Power Management Each Windows power plan will also adjust the processor performance of your machine in order to save power. This is worth bearing in mind if you are experiencing any reduced performance (especially under DC/battery power). 3 Choose High performance (you may need to click Show additional plans to view the High performance plan) for maximum performance when the computer is powered from an AC power source.
Power Management 3 Wake On LAN Support (Windows 8) Wake-On-LAN is only supported from Sleep or Hibernate states in Windows 8. If you require your computer to wake up from network activity in Windows 8 then make sure that the computer is either in Sleep or Hibernate. Wake-On-LAN is not supported from Shutdown states in Windows 8. Power-Saving States You can use power-saving states to stop the computer’s operation and restart where you left off.
Power Management Hibernate Hibernate uses the least amount of power of all the power-saving states and saves all of your information on a part of the hard disk before it turns the system off. If a power failure occurs the system can restore your work from the hard disk; if a power failure occurs when work is saved only to memory, then the work will be lost. Hibernate will also return you to where you last left off within seconds.
Power Management 3 Password Protection Configuring the Power Buttons The power/sleep button (Fn + F4 key combo) and closed lid may be set to send the computer in to a power-saving state. Click Choose what the power buttons do on the left menu in Power Options to bring up the menu. It is recommended that you enable a password on wake up in order to protect your data.
Power Management Adding Hibernate/Sleep to the Power Menu Add Hibernate/Sleep to the Power Menu as follows. 1. 2. 3. 4. 5. Go to the Power Options (Hardware and Sound) control panel (see page 1 - 23). Click “Change settings that are currently unavailable” . Click Choose what the power buttons do. Click to put a tick in the Hibernate/Sleep box under Shutdown settings. Click Save Changes and close the control panel.
Power Management Resuming Operation You can resume operation from power-saving states by pressing the power button, or in some cases pressing the sleep button (Fn + F4 key combo).
Power Management Power Conservation Modes This system supports Energy Star power management features that place computers (CPU, hard drive, etc.) into a low-power sleep modes after a designated period of inactivity. Adjust Power Conservation Modes from the Control Center: 1. 2. 3. Press the Fn + Esc key combination to toggle the Control Center on/off. Click either the Performance, Balanced or Energy Star button.
Power Management Ctrl + Alt + Delete Key Combination You can use the CTRL + ALT + DEL key combination from almost any of the Windows 8 interfaces/Apps to bring up a full-screen displaying Lock, Switch User, Log off, Change a password and Task Manager options. If you click the Power icon in the lower right corner of the screen a power management option menu appears to display Sleep, Shut down, and Restart.
Power Management Battery Information Follow these simple guidelines to get the best use out of your battery. Low Battery Warning Battery Power Your computer’s battery power is dependent upon many factors, including the programs you are running, and peripheral devices attached. You can set actions to be taken (e.g. Shut down, Hibernate etc.), and set critical and low battery levels from power plan Change plan settings > Change advanced power settings (see Figure 3 - 3 on page 3 - 5).
Power Management 3 Windows Mobility Center The Windows Mobility Center control panel provides an easy point of access for information on battery status, power plans used and wireless device status etc. Conserving Battery Power • Use a power plan that conserves power (e.g Power saver), however note that this may have an affect on computer performance. • Lower the brightness level of the LCD display.
Power Management Battery Life Battery life may be shortened through improper maintenance. To optimize the life and improve its performance, fully discharge and recharge the battery at least once every 30 days. We recommend that you do not remove the battery yourself. If you do need to remove the battery for any reason (e.g. long term storage) see “Removing the Battery” on page 6 - 3.
Power Management 3 Caution Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Discard used battery according to the manufacturer’s instructions.
Power Management Battery FAQ How do I completely discharge the battery? Use the computer with battery power until it shuts down due to a low battery. Don’t turn off the computer even if a message indicates the battery is critically low, just let the computer use up all of the battery power and shut down on its own. 1. 2. 3 Save and close all files and applications. Create a power plan for discharging the battery and set all the options to Never.
Power Management 3. Click Change plan settings (after creating it) and click Change plan settings > Change advanced power settings.
Power Management 4. 5. Scroll down to Battery and click + to expand the battery options.
Power Management 3 How do I fully charge the battery? When charging the battery, don’t stop until the LED charging indicator light changes from orange to green. How do I maintain the battery? Completely discharge and charge the battery at least once every 30 days or after about 20 partial discharges.
Drivers & Utilities Chapter 4: Drivers & Utilities This chapter deals with installing the drivers and utilities essential to the operation or improvement of some of the computer’s subsystems. The system takes advantage of some newer hardware components for which the latest versions of most available operating systems haven’t built in drivers and utilities. Thus, some of the system components won’t be auto-configured with an appropriate driver or utility during operating system installation.
Drivers & Utilities Driver Installation 1. 2. 4 3. 4. Insert the Device Drivers & Utilities + User’s Manual disc into the computer’s DVD drive. Click the message “Tap to choose what happens with this disc.” Click Run autorun.exe. Click Install Drivers (button), or Option Drivers (button) to access the Optional driver menu. Figure 4 - 1 - Drivers Installer Screen 1 4 - 2 Driver Installation 5. 6. 7.
Drivers & Utilities Win 8 System Driver Page # Optional Page # Chipset Page 4 - 6 Setting Up SATA RAID or AHCI Mode Page 7 - 2 Video (VGA) Page 4 - 6 PC Camera Module (Not required for Windows 8) Page 7 - 12 NVIDIA Video (VGA) Page 4 - 6 Wireless LAN Module Page 7 - 19 LAN Page 4 - 6 Fingerprint Reader Module Page 7 - 27 Card Reader Page 4 - 6 Bluetooth & WLAN Combo Module Page 7 - 39 TouchPad Page 4 - 6 Intel® Rapid Storage Technology (required for hard disks in AHCI & RAID modes)
Drivers & Utilities Manual Driver Installation Click Browse CD/DVD (button) in the Drivers Installer application and browse to the executable file in the appropriate driver folder. 4 Windows Update After installing all the drivers make sure you enable Windows Update in order to get all the latest security updates etc. (all updates will include the latest hotfixes from Microsoft). See “Windows Update” on page 4 8 for instructions.
Drivers & Utilities User Account Control If a User Account Control prompt appears as part of the driver installation procedure, click Continue or Allow, and follow the installation procedure as directed. Windows Security Message If you receive a Windows security message as part of the driver installation process. Just click “Install this driver software anyway” or “Install” to continue the installation procedure.
Drivers & Utilities Driver Installation Procedure Insert the Device Drivers & Utilities + User’s Manual disc and click Install Drivers (button). 4 Chipset 1. Click 1.Install Chipset Driver > Yes. 2. Click Next > Yes > Next > Next. 3. Click Finish to restart the computer. Video (VGA) 1. Click 2.Install VGA Driver > Yes. 2. Click Next > Yes > Next > Next. 3. Click Finish to restart the computer. NVIDIA Video (VGA) 1. Click 3.Install NVIDIA VGA Driver > Yes. 2.
Drivers & Utilities Airplane 1. Click 7.Install Airplane Driver > Yes. 2. Click Next. 3. Click Finish to restart the computer. Hot Key 1. Click 8.Install Hotkey AP > Yes. 2. Click Next > Next. 3. Click Finish > Finish to restart your computer. MEI Driver 1. Click 9.Install MEI Driver > Yes. 2. Click Next > Yes > Next. 3. Click Finish. After installing the audio driver the system will not return to the Drivers Installer screen.
Drivers & Utilities Windows Experience Index Windows Update 4 After installing all the drivers make sure you enable Windows Update in order to get all the latest security updates etc. (all updates will include the latest hotfixes from Microsoft). To enable Windows Update make sure you are connected to the internet: 1. 2. 3. 4. 5. 6. Go to the Control Panel. Click Windows Update (System and Security/ Security). Click Check for updates (button).
Drivers & Utilities Optional Drivers See the pages indicated in Table 4 - 1, on page 4 - 3 for the driver installation procedures for any modules included in your purchase option. 4 Models A & B Figure 4 - 3 - Optional Drivers Installer Screen Note that you need to install both the WLAN & Bluetooth drivers for the WLAN & Bluetooth Combo modules.
Drivers & Utilities 4 4 - 10
BIOS Utilities Chapter 5: BIOS Utilities Overview This chapter gives a brief introduction to the computer’s built-in software: Diagnostics: The POST (Power-On Self Test) Configuration: The Setup utility If your computer has never been set up, or you are making important changes to the system (e.g. hard disk setup), then you should review this chapter first and note the original settings found in Setup. Even if you are a beginner, keep a record of the settings you find and any changes you make.
BIOS Utilities BIOS Settings Warning 5 Incorrect settings can cause your system to malfunction. To correct mistakes, return to Setup and restore the Previous Values with , or Optimized Defaults with . The Power-On Self Test (POST) If you enable the Boot-time Diagnostic Screen in the Setup Utility, each time you turn on the computer the system takes a few seconds to conduct a POST, including a quick test of the on-board RAM (memory).
BIOS Utilities Failing the POST Errors can be detected during the POST. There are two categories, “fatal” and “nonfatal”. Fatal Errors These stop the boot process and usually indicate there is something seriously wrong with your system. Take the computer to your service representative or authorized distributor/supplier as soon as possible. Non-Fatal Errors This kind of error still allows you to boot.
BIOS Utilities BIOS Settings Warning 5 Incorrect settings can cause your system to malfunction. To correct mistakes, return to Setup and restore the Previous Values with , or Optimized Defaults with . The Setup Utility The Aptio Setup Utility tells the system how to configure itself and manage basic features and subsystems (e.g. port configuration).
BIOS Utilities Setup Screens The following pages contain additional advice on portions of the Setup. Along the top of the screen is a menu bar with menu headings. When you select a heading, a new screen appears. Scroll through the features listed on each screen to make changes to Setup. Instructions on how to navigate each screen are in the box at the bottom right side of the screen. Setup Menus The Setup menus shown in this section are for reference only.
BIOS Utilities Main Menu Figure 5 - 2 Main Menu 5 System Time & Date (Main Menu) The hour setting uses the 24-hour system (i.e., ØØ = midnight; 13 = 1 pm). If you can change the date and time settings in your operating system, you will also change these settings. Some applications may also alter data files to reflect these changes.
BIOS Utilities SATA Port # (Main Menu) Pressing Enter opens the sub-menu to show the configuration of a optical Device/ HDD on the computer’s SATA Ports. System/Extended Memory (Main Menu) This item contains information on the system memory, and is not user configurable. The system will auto detect the amount of memory installed. 5 MB Series / BIOS Revision / KBC/EC firmware Revision (Main Menu) This item contains information on the BIOS version and is not user configurable.
BIOS Utilities Advanced Menu Figure 5 - 3 Advanced Menu 5 Intel(R) Rapid Start Technology (Advanced Menu) Enable/disable Intel(R) Rapid Start Technology from this menu. The rapid start hibernation mode can resume power within 5 to 6 seconds and can remember your computer's state with zero power.
BIOS Utilities Intel(R) Rapid Storage Technology (Advanced Menu) Enable/disable Intel(R) Rapid Storage Technology from this menu to provide high-performance SATA RAID capabilities for Windows 8. Note that this menu item will be available if UEFI Boot is enabled (see “Boot Menu” on page 5 - 14) and the SATA Mode (Advanced Menu) is set to RAID (see below).
BIOS Utilities Boot Logo (Advanced Menu) Use this menu item to enable/disable the Boot Logo screen at system startup if you have not enabled UEFI Boot. If you disable the Boot Logo you will not see the F2 Enter Setup or F7 Boot Options prompts on the screen, however you can still press these keys, while the boot screen is displayed, to perform the Enter Setup or Boot Option functions. 5 Power On Boot Beep (Advanced Menu) Use this menu item to enable/disable the beep as the computer starts up.
BIOS Utilities Security Menu Security Menu The changes you make here affect the access to the Setup utility itself, and also access to your machine as it boots up after you turn it on. These settings do not affect your machine or network passwords which will be set in your software OS. Figure 5 - 4 Security Menu Set Supervisor Password (Security Menu) You can set a password for access to the Aptio Setup Utility. This will not affect access to the computer OS (only the Aptio Setup Utility).
BIOS Utilities Password Warning 5 If you set a boot password (Password on boot is “Enabled“), NEVER forget your password. The consequences of this could be serious. If you cannot remember your boot password you must contact your vendor and you may lose all of the information on your hard disk. Note: To clear existing passwords press Enter and type the existing password, then press Enter for the new password (without typing any password entry) and Enter again to confirm the password clearance.
BIOS Utilities Secure Boot (Security Menu) Secure Boot prevents unauthorized operating systems and software from loading during the startup process. Secure Boot is available as a menu option if you have enabled UEFI Boot (see “Boot Menu” on page 5 - 14). Enabling Secure Boot will bring up the Secure Boot Mode menu to enable you to configure Secure Boot as Standard (with a fixed secure boot policy), or Custom (which enables you to make changes to the Image Execution Policy and Key Management database).
BIOS Utilities Boot Menu Figure 5 - 5 Boot Menu 5 BIOS Screens Note that the BIOS screens pictured on these pages are intended for guidance in setting up your system’s BIOS. BIOS versions are subject to constant change and revision, therefore your computer’s actual screens may appear slightly different from those pictured on these pages. 5 - 14 Boot Menu When you turn the computer on it will look for an operating system (e.g.
BIOS Utilities Boot Option Priorities (Boot Menu) Press Enter to select the Boot Option # and use the arrow keys to select any device in order to move its boot priority up and down the list (the selected device will be highlighted in white). UEFI Boot (Boot Menu) Enable/disable UEFI Boot from this menu. The Unified Extensible Firmware Interface (UEFI) specification provides a clean interface between operating systems and platform firmware at boot time.
BIOS Utilities Exit Menu Figure 5 - 6 Exit Menu 5 Click Save Changes and Reset to save all changes made. Choosing to Discard Changes, or Exit Discarding Changes, will wipe out any changes you have made to the Setup. You can also choose to restore the original Setup defaults that will return the Setup to its original state, and erase any previous changes you have made in a previous session.
Upgrading The Computer Chapter 6: Upgrading The Computer Overview This chapter contains information on upgrading the computer. Follow the steps outlined to make the desired upgrades. If you have any trouble or problems you can contact your service representative for further help.
Upgrading The Computer When Not to Upgrade Power Safety Warning 6 Before you undertake any upgrade procedures, make sure that you have turned off the power, and disconnected all peripherals and cables (including telephone lines and power cord). You must also remove your battery in order to prevent accidentally turning the machine on. Before removing the battery disconnect the AC/DC adapter from the computer.
Upgrading The Computer Removing the Battery If you are confident in undertaking upgrade procedures yourself, for safety reasons it is best to remove the battery. Before removing the battery disconnect the AC/ DC adapter from the computer first. The procedure for removing the battery will depend upon your particular computer model.
Upgrading The Computer Removing The Battery from Model A, B & C Computers 1. 2. 3. 4. 5. Turn the computer off, remove the AC/DC adapter and turn it over. Slide the latch 1 in the direction of the arrow. Slide the latch 2 in the direction of the arrow, and hold it in place. Slide the battery in the direction of the arrow 3 . Lift the battery out of the compartment 4 .
Upgrading The Computer Removing The Battery from Model D & E Computers 1. 2. 3. 4. 5. Turn the computer off, remove the AC/DC adapter and turn the computer over. Slide the latch 1 in the direction of the arrow. Slide the latch 2 in the direction of the arrow, and hold it in place. Lever the battery up at point 3 . Lift the battery out of the compartment 4 .
Upgrading The Computer Upgrading the Optical Device Note the appropriate page for instructions on removing the optical device for your particular model. • “Upgrading the Optical Device (Models A/C)” on page 6 - 7 • “Upgrading the Optical Device (Model B)” on page 6 - 8 • “Upgrading the Optical Device (Models D & E)” on page 6 - 9 6 Secondary Hard Disk Module (Models A & C) Model A & C computers also feature a secondary hard disk module which is interchangeable the optical CD/DVD device.
Upgrading The Computer Upgrading the Optical Device (Models A/C) 1. 2. 3. 4. 5. Turn the computer off, remove the AC/DC adapter (and battery) and turn the computer over. Locate the hard disk bay cover and remove screws 1 & 2 . Lever up the HDD bay cover at point 3 , and then remove the cover 4 . Remove the screw at point 4 , and use a screwdriver to carefully push out the optical device at point 5 . Reverse the process to install any new optical (CD/DVD) device.
Upgrading The Computer Upgrading the Optical Device (Model B) 1. 2. 3. 4. 5. 6. Turn the computer off, remove the AC/DC adapter (and battery) and turn the computer over. Locate the HDD/ODD bay cover and remove screws 1 - 3 . Slide the cover in the direction of arrow 4 , until the case markers 5 line up. Remove the HDD/ODD bay cover 6 Remove the screw at point 7 , and use a screwdriver to carefully push out the optical device.
Upgrading The Computer Upgrading the Optical Device (Models D & E) 1. 2. 3. 4. 5. Turn the computer off, remove the AC/DC adapter (and battery) and turn the computer over. Locate the secondary hard disk bay cover and remove screws 1 & 2 . Remove the hard disk bay cover. Remove the screw at point 3 , and use a screwdriver to carefully push out the optical device out of the bay. Reverse the process to install any new optical (CD/DVD) device.
Upgrading The Computer HDD System Warning New HDD’s are blank. Before you begin make sure: You have backed up any data you want to keep from your old HDD. 6 You have all the CD-ROMs and FDDs required to install your operating system and programs. If you have access to the internet, download the latest application and hardware driver updates for the operating system you plan to install. Copy these to a removable medium.
Upgrading The Computer Removing the Cover from the Primary HDD Bay (Models A & C) 1. 2. 3. Turn the computer off, remove the AC/DC adapter (and battery) and turn the computer over. Locate the hard disk bay cover and remove screws 1 & 2 . Remove the hard disk bay cover 3 by levering the cover at point 4 .
Upgrading The Computer Removing the Cover from the HDD/ODD Bay (Model B) 1. 2. 3. 4. Turn the computer off, remove the AC/DC adapter (and battery) and turn the computer over. Locate the HDD/ODD bay cover and remove screws 1 - 3 . Slide the cover in the direction of arrow 4 , until the case markers 5 line up.
Upgrading The Computer Removing the Cover from the Primary HDD Bay (Models D & E) 1. 2. 3. Turn the computer off, remove the AC/DC adapter (and battery) and turn the computer over. Locate the hard disk bay cover and remove screws 1 & 2 . Remove the hard disk bay cover 3 by levering the cover at point 4 .
Upgrading The Computer RAID Hard Disks All hard disks in a RAID should be identical (the same size and brand) in order to prevent unexpected system behavior. 6 Removing the Primary HDD Assembly 1. 2. 3. When the cover is removed, follow the instructions below to remove the HDD assembly. Slide the HDD assembly in the direction of arrow 1 . Remove the hard disk assembly 2 . Hard Disk Handling Do not press down on the center off the hard disk as this area houses the hard disk drive motor.
Upgrading The Computer 4. 5. Remove screws 3 & 4 and the insulation plate 5 . Reverse the process to install a new disk (see over) and do not forget to install the insulation plate.
Upgrading The Computer Inserting the Hard Disk Into the Primary HDD Bay 1. 2. 3. 6 Make sure the HDD assembly is aligned with the black taped area 1 . When aligned, carefully insert the HDD assembly 2 into the case so that the connectors line up. Replace the hard disk bay covers and screws.
Upgrading The Computer Removing the Hard Disk from the Caddy HDD Bay (Models A & C) Note that the secondary hard disk module is used to replace the optical device module (CD/DVD) in Models A & C computers. 1. 2. 3. 4. 5. 6. Turn the computer off, remove the AC/DC adapter (and battery) and turn the computer over. Remove the optical device (see page 6 - 7 or page 6 - 8). Remove screws 1 - 4 from the rear of the secondary HDD module assembly. Slide the HDD in the direction of arrow 5 .
Upgrading The Computer Removing the Hard Disk from the Secondary HDD Bay (Model B) RAID Hard Disks All hard disks in a RAID should be identical (the same size and brand) in order to prevent unexpected system behavior. Note that the secondary hard disk (Model B if installed) is located under the optical device bay (CD/DVD). 1. 2. 3. 4. Turn the computer off, remove the AC/DC adapter (and battery) and turn the computer over.
Upgrading The Computer 5. 6. Slide the secondary HDD assembly in the direction of the arrow 5 (it will not move fully out of the bay), Lift the secondary HDD assembly 6 up out of the bay (in the reverse direction to arrow 5 ).
Upgrading The Computer 7. Remove screws 7 - 10 and the insulation plate 11 . 9 8 Figure 6 - 15 Secondary Hard Disk Insulation Plate Removal (Model B) 11 10 7 6 8. 9. 10. 11. Reverse the process to install a new disk (make sure you install the insulation plate). Slide the HDD assembly into the bay at an angle as illustrated. Make sure the insulation plate slides under the HDD bay guide at point 11 .
Upgrading The Computer Removing the Hard Disk from the Secondary HDD Bay (Models D & E) Note that the secondary hard disk (Models D & E if installed) is located under the optical device bay (CD/DVD). 1. 2. 3. 4. Turn the computer off, remove the AC/DC adapter (and battery) and turn the computer over. Remove the optical device (see “Upgrading the Optical Device (Models D & E)” on page 6 - 9) When the optical device is removed the secondary HDD assembly will be visible.
Upgrading The Computer 5. 6. Slide the secondary HDD assembly in the direction of the arrow 4 (it will not move fully out of the bay), Lift the secondary HDD assembly 5 up out of the bay (in the reverse direction to arrow 4 ).
Upgrading The Computer 7. Remove screws 6 - 9 and the insulation plate 10 . 9 8 6 10 Figure 6 - 19 Secondary Hard Disk Insulation Plate Removal (Models D & E) 7 6 8. 9. 10. 11. Reverse the process to install a new disk (make sure you install the insulation plate). Slide the HDD assembly into the bay at an angle as illustrated. Make sure the insulation plate slides under the HDD bay guide at point 11 .
Upgrading The Computer Under Keyboard RAM 6 Note that the RAM located under the keyboard is not user upgradable. Contact your distributor/ supplier for more information if you wish to upgrade the memory in the secondary memory sockets. Upgrading the System Memory (RAM) The computer has four memory sockets for 204 pin Small Outline Dual In-line (SODIMM) DDR III (DDR3) type memory modules (see “Memory” on page D - 2).
Upgrading The Computer Removing the Component Cover (Models A & C) 1. 2. Turn the computer off, remove the AC/DC adapter (and battery) and turn the computer over. Remove screws 1 - 4 from the bottom of the computer . 2 1 4 3 Figure 6 - 21 Component Cover Screws Models A & C 3. 4. Slide the component bay cover until the cover and case indicators 5 are aligned. Lift the cover 6 off the computer.
Upgrading The Computer Removing the Component Cover (Model B) 1. 2. Turn the computer off, remove the AC/DC adapter (and battery) and turn the computer over. Remove screws 1 - 4 from the bottom and rear of the computer . 1 4 3 Figure 6 - 23 6 2 Component Cover Screws Model B Model B 3. 4. Slide the component bay cover until the cover and case indicators 5 are aligned. Lift the cover 6 off the computer.
Upgrading The Computer Removing the Component Cover (Model D) 1. 2. Turn the computer off, remove the AC/DC adapter (and battery) and turn the computer over. Remove screws 1 - 4 from the bottom of the computer . 2 1 4 3 Figure 6 - 25 Component Cover Screws Model D 3. 4. Slide the component bay cover until the cover and case indicators 5 are aligned. Lift the cover 6 off the computer.
Upgrading The Computer Removing the Component Cover (Model E) 1. 2. Turn the computer off, remove the AC/DC adapter (and battery) and turn the computer over. Remove screws 1 - 6 from the bottom and rear of the computer . 2 1 3 Figure 6 - 27 6 4 5 6 Component Cover Screws Model E 3. 4. Slide the component bay cover until the cover and case indicators 7 are aligned. Lift the cover 8 off the computer.
Upgrading The Computer System Memory (RAM) Module Removal 1. Gently pull the two release latches ( 1 & 2 ) on the sides of the memory sockets) in the direction indicated below. 1 2 1 2 Contact Warning Be careful not to touch the metal pins on the module’s connecting edge. Even the cleanest hands have oils which can attract particles, and degrade the module’s performance. Figure 6 - 29 RAM Module Removal 2. 3. 4. 5. 6. 7. The RAM module will pop-up, and you can remove it.
Upgrading The Computer Replacing the Component Bay Cover After the RAM has been installed make sure you replace the component bay cover and all screws. 1. 2. 3. 4. Place the component bay cover on the main computer assembly. Align the markers on the cover and main computer assembly (see the appropriate component bay cover removal page for your model). Slide the cover in position to lock it. Replace the appropriate screws (see the appropriate component bay cover removal page for your model).
Upgrading The Computer Upgrading the Processor If you want to upgrade your computer by replacing the existing processor with a faster/new one you will need to contact your customer service representative. We recommend that you do not do this yourself, since if it is done incorrectly you may damage the processor or mainboard.
Upgrading The Computer 6 6 - 32
Modules Chapter 7: Modules Overview This chapter contains the information on the various modules (some of which are optional) which may come with your computer, depending on the configuration purchased. If you are unsure please contact your service representative.
Modules RAID Hard Disks All hard disks in a RAID should be identical (the same size and brand) in order to prevent unexpected system behavior. SATA Mode Selection 7 The SATA mode selection should be made before installing your operating system. DO NOT change your selected SATA mode unless you intend to reinstall your operating system. Make sure you have backed up all your data before doing so.
Modules RAID Level Description Table 7 - 1 RAID 0 Identical drives reading and writing data in parallel to increase performance. RAID 0 implements a striped disk array and the data is broken into blocks and each block is written to a separate disk drive. RAID Levels RAID 1 Identical drives in a mirrored configuration used to protect data. Should a drive that is part of a mirrored array fail, the mirrored drive (which contains identical data) will handle all the data.
Modules SATA RAID Setup Procedure (Windows 8) To configure your RAID (Redundant Array of Independent Disks) system in Striping (RAID 0) or Mirroring (RAID 1) modes (see Table 7 - 1, on page 7 - 3) you will require at least two identical (see sidebar) hard disks. Note that the RAID setup in Windows 8 differs from that outlined for Windows7. You need to setup a RAID before installing your Windows 8 operating system, and you will need to prepare the following in order to do so. 7 1. 2. 3. 4. 5. 6.
Modules 1. 2. 3. Go to the operable computer and insert a USB Flash drive or external USB hard disk. Insert the Device Drivers & Utilities + User’s Manual disc into the CD/DVD drive of the operable computer. Copy the f6flpy-x86 or f6flpy-x64 folder from the location below (D: denotes your DVD drive) on the Device Drivers & Utilities + User’s Manual disc to the USB flash drive or external USB hard disk. • For Windows 8 32bit = D:\Options\RAID\f6flpy-x86 • For Windows 8 64bit = D:\Options\RAID\f6flpy-x64 4.
Modules 13. You can now setup your RAID volume using any two installed disks. 14. Go to Name: and press . 15. Type a name of your choice for your RAID volume and press .
Modules 16. Go to RAID Level: and press . 17. Choose the RAID Level required (see Table 7 - 1, on page 7 - 3 for details) and press . • RAID0 (Stripe) • RAID1 (Mirror) • Recovery 18. Go to any of the disks listed under Select Disks: and select a disk name and press . 19. Move the cursor down (use the arrow keys) onto to X (o select the disk required and press .
Modules 20. You should select two identical disks to form your RAID volume. 21. If you have selected RAID0 (Stripe) then you can adjust the “Strip Size” to your requirements. 22. If you have selected Recovery then you can adjust the Synchronization to “On Request” or “Continuous”. 23. Go to Create Volume and press . 24. The RAID volume will then be created and the RAID information will be displayed under Intel(R) Rapid Storage Technology (in the Advanced menu).
Modules 25. Press to exit the menu. 26. Press and to “Save Changes and Reset”, however ensure that the two conditions in the bulleted points below are met before doing so. • Make sure the Windows 8 OS DVD is in the DVD drive. and as the computer starts up it will automatically boot from the Windows 8 OS DVD (you will be prompted to press a key to boot from the DVD). • Make sure your USB Flash drive or external USB hard disk is attached to one of the USB ports on the computer. 27.
Modules 35. Install the Windows drivers from the Device Drivers & Utilities + User’s Manual disc as per Table 4 - 1, on page 4 - 3 (make sure you install the Intel Rapid Storage Technology driver - see overleaf). 36. Run the Intel® Rapid Storage Technology application to manage your RAID volume as instructed in “Intel® Rapid Storage Technology for RAID Systems” on page 7 - 46. 7 IRST Driver Installation 1. Insert the Device Drivers & Utilities + User’s Manual disc into the DVD drive. 2.
Modules Deleting a RAID (Windows 8) If you wish to delete an existing RAID then follow the procedure below to do so. However backup up any necessary files and data before deleting a RAID, as doing so will result in the loss of all data on the RAID volumes. 1. 2. 3. 4. 5. Start-up your notebook computer and press to enter the BIOS. Go to Intel(R) Rapid Storage Technology (in the Advanced menu) and press . Go to the RAID (listed under RAID Volumes:) and press .
Modules PC Camera Module When the PC Camera application is run the LED indicator to the left of the camera will be illuminated in red. Note that you need to use the Camera app in Windows 8 to take pictures and capture video. Use the Fn + F10 key combination (see “Function Keys & Visual Indicators” on page 1 - 14) to toggle power to the PC Camera module.
Modules PC Camera Audio Setup If you want to capture video & audio with your camera, it is necessary to setup the audio recording options in Windows. 1. 2. 3. 4. 5. 6. Go to the Control Panel. Click Sound (Hardware and Sound) and click Recording (tab). Right-click hold and release Microphone (Realtek High Definition Audio) and make sure the item is not disabled. Double-click Microphone (or select Properties from the right-click menu).
Modules Camera App 1. 2. 3. Make sure the camera is powered on (use the Fn + F10 key combination to toggle power to the camera module). Click the Camera app icon in the Start screen to run the Camera app . The camera interface is a translucent app bar with three buttons. Figure 7 - 7 Camera App Bar • Camera options:.
Modules You can also click on More to adjust Brightness, Contrast and Flicker (if you find that the video screen in the camera program is flickering, you can try to adjust the setting here). Eliminating Screen Flicker If you find that the video screen in the camera program is flickering, you can try to adjust the setting in Flicker under More Options.
Modules Taking Pictures/Capturing Video 1. 2. 3. 4. 5. 6. 7. Make sure the camera is powered on (use the Fn + F10 key combination to toggle power to the camera module). Click the Camera app icon in the Start screen to run the Camera app . Click to select the timer if you require a countdown before capture. Click to select either photo or video modes. Click in the main window to take a picture or start video capture (if video capture begins a timer will appear in the bottom right corner of the screen).
Modules 8. A scroll arrow will appear on the left side of the screen after any pictures/videos have been captured. 9. Click the arrows (on either side of the screen) to browse through the captured photos/video, and back to the Camera app. 10. Clicking on a captured photo will bring up an app bar with Crop and Delete buttons. Figure 7 - 11 Crop & Delete Buttons (for Still Photos) 11. Use the handles to Crop any captured picture, and click OK to save the changes made. 12.
Modules Reducing Video File Size Note that capturing high resolution video files requires a substantial amount of disk space for each file. After recording video, check the video file size (right-click the file and select Properties) and the remaining free space on your hard disk (go to My Computer, right-click the hard disk, and select Properties). If necessary you can remove the recorded video file to a removable medium e.g. CD, DVD or USB Flash drive.
Modules Wireless LAN Module If you have included an Intel® or 3rd Party WLAN module in your purchase option make sure that the module is on (i.e. the system is not in Airplane Mode) before installing the driver. Make sure you install the drivers in the order indicated in Table 4 - 1, on page 4 - 3. Note that you need to install both the WLAN & Bluetooth drivers for the WLAN & Bluetooth Combo modules.
Modules 3rd Party 802.11b/g/n Driver Installation 1. Make sure the system is not in Airplane Mode, and then insert the Device Drivers & Utilities + User’s Manual disc into the DVD drive. 2. Click Option Drivers (button). 3. Click 1.Install WLAN Driver > Yes. 4. Click Next. 5. Click Finish to restart the computer. 6. The operating system is the default setting for Wireless LAN control in Windows (see page 7 - 21). 7 Intel® WLAN Driver Installation 1.
Modules WLAN Configuration in Windows 8 You can configure a wireless connection using one of the following options, however make sure the Wireless LAN module is turned on (and not in Airplane Mode) before configuration begins. Charms Bar 1. 2. 3. Go to the Charms Bar. Select Settings and then click the WiFi icon (it should read Available under the icon and Airplane mode should be Off). A list of available access points will appear.
Modules 4. 5. 6. 7. 8. Double-click an access point to connect to it (or click it and click Connect). Enter a network security key (password) if required, and click Next. You can choose to share or connect to devices or not. When you are connected to the network access point it will display the Connected icon . Select any connected network and click Disconnect to disconnect from a connected access point. 7 Figure 7 - 14 Networks Connected / Disconnect 9.
Modules 11. You need to either use Airplane Mode, or to turn the WLAN module off aboard aircraft.
Modules Desktop Mode 1. 2. 3. 4. 5. 6. 7. Switch to the Windows Desktop (click the app or use the Windows logo key D key combination). Click the wireless icon in the notification area of the taskbar. A list of available access points will appear. Double-click an access point to connect to it (or click it and click Connect). Enter a network security key (password) if required, and click Next. You can choose to share or connect to devices or not.
Modules Control Panel If you are in Category View do the following (see over for Icon View): 1. 2. 3. Open the Control Panel. Click the Network and Internet control panel. Click Connect to a network. Figure 7 - 17 Network and Internet Control Panel 4. 5. 6. 7. 8. A list of available access points will appear. Double-click an access point to connect to it (or click it and click Connect). Enter a network security key (password) if required, and click Next.
Modules If you are in Icon View do the following: 1. 2. 3. 4. Open the Control Panel. Click Network and Sharing Center. Click Change Adapter Settings. Double-click Wi-Fi. 5. 6. 7. 8. 9. A list of available access points will appear. Double-click an access point to connect to it (or click it and click Connect). Enter a network security key (password) if required, and click Next. You can choose to share or connect to devices or not.
Modules Fingerprint Reader Module The optional fingerprint reader Protector Suite Software provides a high level of security for your computer. Make sure you have administrator’s rights to your computer, and have a Windows password enabled for full security protection. A further level of security and control is provided in the BIOS (see “Security Menu” on page 5 - 11).
Modules Fingerprint Reader Driver Installation 1. Insert the Device Drivers & Utilities + User’s Manual disc into the CD/ DVD drive. 2. Click Option Drivers. 3. Click 2.Install Finger Print Driver > Yes. 4. Click Next. 5. Click Finish to restart the computer.
Modules AuthenTec TrueSuite Application The AuthenTec TrueSuite application is used in conjunction with your fingerprint reader to enroll fingerprints and manage settings etc. User Enrollment 1. 2. 3. 4. 5. 6. Run the AuthenTec TrueSuite application. Click Yes when you have identified your fingerprint reader sensor( 1 in Figure 7 - 19). Click Yes when you are ready to enroll your fingerprints. Click on the fingerprint diagram to select any finger to enroll.
Modules 7. Help Click the Help icon and select a help topic from the drop-down menu. Get more help will provide a more comprehensive list of help topics. You will be prompted to select another finger for enrollment (it is recommended that you enroll a number of fingers - see sidebar). 8. Click the button to continue once you have enrolled a number of fingerprints. 9. Enter the required information and click the button to register your software, or click to register later. 10.
Modules Settings Click the Settings button on the menu bar to access the personalization settings for AuthenTec TrueSuite. Here you can choose to enable/disable Website Log On, QuickLaunch, Fast User Switching and the desktop icon. You can also select the Theme and export/import identities. Click the Save button to save any changes made.
Modules Windows Log On Windows log on allows you to gain access to your computer by swiping your finger across the fingerprint reader sensor. Use the Biometric Devices control panel (in the Hardware & Sound category) in Windows to turn Biometrics on/off when required. Access the Biometric Devices control panel and select Change biometric settings to turn the biometrics on or off, or to allow users to log on to Windows using fingerprints.
Modules Website Log On Use a fingerprint swipe to log on to websites to help you avoid having to remember user names and passwords across multiple websites (browsers supported are Internet Explorer, Firefox and Chrome). Registering a Website 1. 2. 3. 4. Use your web browser to navigate to the website required. Enter your user name and password and sign in to the website. An AuthenTec TrueStudio dialog box will pop-up. Click Save Password to register the website. Figure 7 - 23 Save Password 5.
Modules QuickLaunch QuickLaunch allows you to drag and drop icons (which represent websites, folders, applications and/or computer actions) to any enrolled finger and then swipe your finger to launch the icons assigned to that finger. 1. 2. 3. 4. 5. Run the AuthenTec TrueSuite application. Click Select Category (button) to group icons if required. Drag and drop an icon to an enrolled finger. To launch the website, folder, application and/or action just swipe your finger across the sensor.
Modules Adding a Website to QuickLaunch 1. 2. 3. 4. 5. Run the AuthenTec TrueSuite application. Click the Add Website button on the menu bar and the dialog box will be displayed. Enter the website URL, name, icon and category as required. Click Save and an icon will be associated with the selected website. To delete an icon right-click it and select Delete Icon and it will no longer be associated with the finger.
Modules Dock View Dock View displays the website icons across the bottom of the screen. Each icon wiLl have an associated web card which displays the website information, user name and password etc. This information may be edited or deleted as required. Figure 7 - 27 Dock View Editing a Web Card 1. 2. 3. 4. 5. 6. 7. 7 Run the AuthenTec TrueSuite application. Left-click a web card to bring up the associated information. You can click the reveal/hide password button to see or hide the password.
Modules Exporting and Importing Your Identity You can export your identity to backup your information, or to move it to another computer. Exporting Your Identity 1. 2. 3. 4. 5. 6. Run the AuthenTec TrueSuite application. Click the Settings button on the menu bar. Click Export My Identity. You will be required to enter and confirm a passphrase and click Next. Browse to a location to Save the file. Swipe a finger to confirm the export. 7 Importing Your Identity 1. 2. 3. 4. 5. 6. 7.
Modules AuthenTec KeepSafe The KeepSafe folder is an encrypted area assigned on your hard drive that allows you to store files and folders to be protected by fingerprint protection. The folder will appear on your desktop (if selected in the Personalization Settings) and in My Computer, but will not be visible to other users of your computer. To lock/unlock the KeepSafe folder right-click it to display the context menu and select Unlock/Lock.
Modules Bluetooth & WLAN Combo Module If your purchase option includes the Combination Wireless LAN & Bluetooth module (either Intel® or 3rd Party) then install the driver as instructed overleaf. Make sure that the module is on (i.e. the system is not in Airplane Mode) before installing the driver. Bluetooth Data Transfer Note that the transfer of data between the computer and a Bluetooth enabled device is supported in one direction only (simultaneous data transfer is not supported).
Modules High Speed Bluetooth Data Transfer 7 The Combination Wireless LAN & Bluetooth module supports high speed data transfer. However to achieve such transfer speeds, both devices must support high speed data transfer. To obtain high speed data transfer make sure that both the WLAN and Bluetooth modules are powered on. Check your Bluetooth compatible device’s documentation to confirm it supports high speed data transfer. 3rd Party Bluetooth (V4.0) Combo Driver Installation 1.
Modules Bluetooth Configuration in Windows 8 You can configure a Bluetooth connection as below, however make sure the Bluetooth module is on (i.e. not in Airplane Mode) before configuration begins. Desktop Mode 1. 2. 3. Switch to the Windows Desktop (click the App or use the Windows logo key D key combination). Click the notification area of the taskbar and double-click the Bluetooth icon click and select Show Bluetooth Devices). The Devices item in PC Settings will appear. OR + (or \ Charms Bar 1. 2.
Modules 4. 5. Click Add a Device. Double-click the device you want to pair with the computer. 6. On first connection the computer will provide you with a pairing code to be entered onto the device. 7. Enter the code into your Bluetooth enabled device and click Yes on the computer to complete the pairing.
Modules 8. You need to either use Airplane Mode, or to turn the Bluetooth module off aboard aircraft.
Modules To Make your Computer Discoverable to Bluetooth Devices 1. 2. 3. 4. Switch to the Windows Desktop (click the app or use the Windows logo key + D key combination). Click the notification area of the taskbar, click the Bluetooth icon and click Open Settings. Click Options, and make sure that Allow Bluetooth devices to find this computer check box (Discovery) has a tick inside it.
Modules Intel® Rapid Storage Technology The Intel Rapid Storage Technology application provides high-performance SATA and SATA RAID capabilities. Install the Intel Rapid Storage Technology application (after installing all necessary drivers in the correct order) to support your RAID system or SATA drive if set up in AHCI mode in the BIOS (see “SATA Mode (Advanced Menu)” on page 5 - 9). IRST Driver Installation 1. Insert the Device Drivers & Utilities + User’s Manual disc into the DVD drive. 2.
Modules Intel® Rapid Storage Technology for RAID Systems Intel® Rapid Storage Technology application displays status information on your RAID configuration. Run the Intel® Rapid Storage Technology application from the item in the Start menu. When the Intel® Rapid Storage Technology application is launched the system will open the Status window. Here you can view the general health of the storage system. Various volume creation and management options are available depending on the system’s status.
Modules Intel® Rapid Storage Technology Help If a hard drive member of a RAID volume is reported as “Degraded” or “Failed” it may be possible to recover the volume. If the volume cannot be restored then you will need to recreate the RAID volume and restore the data from a back up. Click the Help menu (or press F1) for instructions on how to recover or recreate RAID Volumes. Help Click the Help (or press F1) menu button at the top of the Intel® Rapid Storage Technology application.
Modules RAID Volume Data Verification and Repair The RAID volume data verification process identifies any inconsistencies or bad data on a RAID 0 or RAID 1 volume. The table outlines what occurs for each RAID level: Table 7 - 2 RAID Level Verification & Repair Status 7 RAID Level Verify RAID 0 Bad blocks are identified. Verify & Repair N/A Bad blocks are reassigned. Bad blocks are identified. RAID 1 Data on the mirrored drive is compared to data on the source drive.
Modules Verifying and Repairing RAID Volume Data 1. 2. 3. 4. 5. 6. Before verifying the volume data you will need to initialize the volume. Run the Intel® Rapid Storage Technology application. Click to select the RAID in the pane on the right side of the window. Click Manage and click Advanced. Click Initialize and click Yes (button) to begin the process. The completion percentage will be listed under Status.
Modules 7. 8. 7 Click Advanced and click Verify, then click Verify (button) to begin the process. The completion percentage will be listed under Status (verifying and repairing).
Modules Intel® Rapid Start Technology Driver Intel(R) Rapid Start Technology can resume power from Hibernation within 5 to 6 seconds and can remember your computer's previous state with zero power. System Requirements to support Intel® Rapid Start Technology: • Rapid Start Technology should be enabled in the BIOS (see ““Intel(R) Rapid Start Technology (Advanced Menu)” on page 5 - 8). • Intel Rapid Storage Technology software installed. • A Solid State Drive (SSD) with a minimum capacity of 18.6GB.
Modules Intel® Rapid Start Technology Configuration 1. 2. 3. 7 Enable/disable Intel(R) Rapid Start Technology from the BIOS (see “Intel(R) Rapid Start Technology (Advanced Menu)” on page 5 - 8). Go the Windows control panel and double-click Administrative Tools (System and Security)> Computer Management > Storage > Disk Management Right-click the SSD and select Shrink Volume from the menu.
Modules 4. Enter the figure, which should be equal to amount of system memory (RAM) in your computer, in “Enter the amount of space to shrink in MB”. Figure 7 - 39 Shrink Volume Size 7 5. Click Shrink (any unallocated file space may be formatted for storage use). Memory Size (Amount of Space to Shrink) The figure entered in the “Enter the amount of space to shrink in MB” field above should be equal to the amount of system memory in your computer.
Modules 6. Run the Desktop app and right-click the lower left hot corner (or use the Windows Logo Key + X key combination) and select Command Prompt (Admin). 7. 8. Type “DISKPART”. At the DISKPART command type “list disk”.
Modules 9. Type “select disk #” (# is disk number where you want to create the store partition, so refer to the results obtained from "list disk" for exact disk number). 10. The message “Disk # is now the selected disk.” will appear. Figure 7 - 42 Diskpart - Select Disk # 7 11. Type “create partition primary”. 12. A “DiskPart succeeded in creating the specified partition.” message should appear.
Modules 13. Type “detail disk”. Figure 7 - 44 Diskpart - Detail Disk 14. Type “select Volume #” (# is volume of your storage partition so refer to results obtained from "detail disk" for the exact volume number). 15. The message “Volume # is now the selected volume.” will appear.
Modules 16. Type the following, depending on the format of the SSD. • For MBR formatted SSDs: “set id=84 override” (the id must be set to 84). • For GPT formatted SSDs: “set id=D3BFE2DE-3DAF-11DF-BA40-E3A556D89593”. Figure 7 - 46 Diskpart - Set id= 7 17. The message “DiskPart successfully set the partition ID.” will appear. 18. Close the CMD window.
Modules Figure 7 - 47 19. Go the Windows control panel and double-click Administrative Tools (System and Security)> Computer Management > Storage > Disk Management. 20. The disk partition should read Healthy Hibernation Partition. Computer Management (Healthy Hibernation Partition) Healthy (Hibernation Partition) 7 21. Restart the computer. 22. Install the driver (see below). Intel® Rapid Start Technology Driver Installation 1.
Modules Intel® Wireless Display Application The Intel® Wireless Display Application (requires Intel® Centrino WLAN/ Combo module), in conjunction with a compatible video adapter (purchased separately), allows you to display the contents of the notebook display on another display (e.g. HDTV) without the need to have cables stretching across a room. You can then play games, browse the internet, display videos or photo slide shows on your TV/external display without using HDMI or A/V cables.
Modules Intel® WiDi Application Installation 1. Insert the Device Drivers & Utilities + User’s Manual disc into the DVD drive. 2. Click Option Drivers (button). 3. Click 6.Install Intel WiDi AP > Yes. 4. Click Next. 5. Click the button to accept the license and click Next. 6. Click Finish.
Modules Intel® WiDi Application Configuration 1. 2. 3. Run Intel(R) Wireless Display from the Start screen. Click I agree to the terms of this license (button). The application will scan for any connected compatible adapters (or you can click the Scan for available adapters button to enable Intel My WiFi Technology).
Modules 4. 5. 6. Click to select and detected adapters, and click Connect. The system will then prompt you to enter the 4-digit security code which will be displayed on the external TV Screen (or press the connect button on the wireless speaker adapter). Enter the code for the video adapter and click Continue.
Modules 7. 8. You will then be prompted to enter a name for the video adapter and click Continue. Click Finished to complete the setup. Test Audio Adapter To verify a successful audio connection (for Intel® Wireless Music), select the “Test your audio connection” link or select “Finished” to bypass the test. You can select “Play Sample” to play an audio test sample from your adapter to the connected speaker set.
Modules Sound Blaster Audio Install the Sound Blaster AP to allow you to configure the audio settings to your requirements for the best performance in games, music and movies. Sound Blaster X-Fi MB-3 Audio AP Installation 1. Insert the Device Drivers & Utilities + User’s Manual disc into the CD/ DVD drive. 2. Click Option Drivers (button). 3. Click 7.Install SBX-Fi MB 3 AP > Yes. 4. Click Next > Yes to accept the license. 5. Click Next > Full Installation (button). 6.
Modules Volume Controls You can click on the volume dials to adjust the level for either the microphone or master volume. You can choose to save the settings for Music, Movie or Game, and these settings can be exported or imported as required.
Modules Smart Volume Setting SBX Pro Studio Click the tickbox to enable/disable the control, and use the slider to adjust the levels. Press the play button to test settings. The default setting for Smart Volume in SBX Pro Studio is set to Normal. 7 To get the full effect of this setting it is recommended that you set it to Loud. Figure 7 - 53 Sound Blaster X-Fi 3 SBX Pro Studio • • • • • Crystalizer: Enhances audio to make it sound livelier.
Modules Scout Mode Click in the box to enable Scout Mode to enhance your ability to hear enemies in games from a further distance away than would normally be possible.
Modules Voice FX Click in the box to enable Voice FX and click on the sliders to adjust the settings. Select the mode required from the dropbox, and click on Test to hear the playback of the effect.
Modules EAX Effects & EQ Click to select either/or EAX Effects or EQ, select the mode required from the dropbox and click on the sliders to adjust the settings. Click on Save to save any custom changes to the set levels and effects.
Modules Advanced Settings Select the speaker/headphone configuration from the dropbox, and click on Test to hear the effect. You can also adjust the Bass Management by clicking the Bass Redirection and Subwoofer Gain, and click on the slider to adjust the Crossover Frequency.
Modules Hot Key Configuration Click Configure Hot Keys in Scout Mode or Advanced Settings menus to access the Hot Key Configuration menu. Click Enable All Hot Keys, and then click on the task and press the key sequence required. Any hotkeys chosen will be locked by the application, and therefore will not be able to be used in other applications.
Modules Creative ALchemy The Creative ALchemy application can be run from the shortcut in the Start menu. Use the left menu to select any installed games and click the button to move them to the right column to enable ALchemy support for the game. Creative ALchemy restores hardware accelerated audio to enable EAX effects and 3D Audio when playing Direct Sound3D games.
Troubleshooting Chapter 8: Troubleshooting Overview Should you have any problems with your computer, before consulting your service representative, you may want to try to solve the problem yourself. This chapter lists some common problems and their possible solutions. This can’t anticipate every problem, but you should check here before you panic. If you don’t find the answer in these pages, make sure you have followed the instructions carefully and observed the safety precautions in the preface.
Troubleshooting Basic Hints and Tips Many of the following may seem obvious but they are often the solution to a problem when your computer appears not to be working. • Power - Is the computer actually plugged into a working electrical outlet? If plugged into a power strip, make sure it is actually working. Check the LED Power Indicators (see “LED Indicators” on page 1 - 11) to see the computer’s power status. • Connections - Check all the cables to make sure that there are no loose connections anywhere.
Troubleshooting Backup and General Maintenance • Always backup your important data, and keep copies of your OS and programs safe, but close to hand. Don’t forget to note the serial numbers if you are storing them out of their original cases, e.g. in a CD wallet. • Run maintenance programs on your hard disk and OS as often as you can. You may schedule these programs to run at times when you are not using your computer.
Troubleshooting Viruses • Install an Anti-Virus program and keep the definitions file (the file which tells your program which viruses to look for) up to date. New computer viruses are discovered daily, and some of them may seriously harm your computer and cause you to lose data. Anti-Virus programs are commercially available and the definitions file updates are usually downloadable directly from the internet. • Be careful when opening e-mail from sources you don’t know.
Troubleshooting Upgrading and Adding New Hardware/Software • Do not be tempted to make changes to your Windows Registry unless you are very sure of what you are doing, otherwise you will risk severely damaging your system. • Don’t open your computer or undertake any repair or upgrade work if you are not comfortable with what you are doing. • Read the documentation.
Troubleshooting • Don’t over complicate things. The less you have to deal with then the easier the source of the problem may be found; Example - if your computer has many devices plugged into its ports, and a number of programs running, then it will be difficult to determine the cause of a problem. Try disconnecting all of the devices and restarting the computer with all the peripheral devices unplugged.
Troubleshooting Problems and Possible Solutions Problem Possible Cause - Solution You turned on the power but it doesn’t work. Battery missing / incorrectly installed. Check the battery bay, make sure the battery is present and seated properly (the design of the battery only allows it to go in one way). Make sure there’s nothing interfering with the battery contacts. The battery LED power indicator blinking orange. , is Low Battery. Plug in the DC power source.
Troubleshooting Problem The computer feels too hot. Possible Cause - Solution Make sure the computer is properly ventilated and the Vent/Fan intakes are not blocked. If this doesn’t cool it down, put the system into Hibernate mode or turn it off for an hour. Make sure the computer isn’t sitting on a thermal surface (see “Overheating” on page 1 - 25/1 - 27). Make sure you’re using the correct adapter.
Troubleshooting Problem Possible Cause - Solution You forget the boot password. If you forget the password, you may have to discharge the battery of the CMOS. Contact your service representative for help. Password Warning If you choose to set a boot password, NEVER forget your password. The consequences of this could be serious. If you cannot remember your boot password you must contact your vendor and you may lose all of the information on your hard disk.
Troubleshooting Problem Possible Cause - Solution Other Keyboards If your keyboard is damaged or you just want to make a change, you can use any standard USB keyboard. The system will detect and enable it automatically. However special functions/hot keys unique to the system’s regular keyboard may not work. 8 The system freezes or the screen goes dark. The system’s power saving features have timed-out.
Troubleshooting Problem Possible Cause - Solution The Wireless LAN/Bluetooth modules cannot be configured. The driver(s) for the module(s) have not been installed. Make sure you have installed the driver for the appropriate module (see the instructions for the appropriate module in “Wireless LAN Module” on page 7 - 19 and/or “Bluetooth & WLAN Combo Module” on page 7 - 39). A file cannot be copied connected Bluetooth device.
Troubleshooting Problem Possible Cause - Solution The computer is off (or in Sleep Mode) but powered by the AC/DC adapter plugged in to a working outlet, or by battery with a capacity above 20%. I have plugged a device into the powered USB port in order to charge it, but the device is not charging. The port is not powered on. Toggle power to the port using the Fn + power button combination. This function may not work with certain external USB compliant devices (check your device’s documentation).
Interface (Ports & Jacks) Appendix A: Interface (Ports & Jacks) Overview The following chapter will give a quick description of the ports & jacks which allow your computer to communicate with external devices, connect to the internet etc.
Interface (Ports & Jacks) Ports and Jacks Item Card Reader Description The card reader allows you to use the following digital storage cards: MMC (MultiMedia Card) / RSMMC SD (Secure Digital) / Mini SD / SDHC / SDXC MS (Memory Stick) / MS Pro / MS Duo Push the card into the slot and it will appear as a removable device. DC-In Jack DisplayPort / Mini DisplayPort Plug the supplied AC/DC adapter into this jack to power your computer.
Interface (Ports & Jacks) Item Description HDMI-Out Port The HDMI-Out (High-Definition Multimedia Interface) port is an audio/video connector interface for transmitting uncompressed digital streams. This allows you to connect an external monitor, TV or Flat Panel Display etc. as a display device (see “Attaching Other Displays” on page C - 21) by means of a HDMI cable. Note that HDMI carries both audio and video signals. Headphone-Out Jack Headphones or speakers may be connected through this jack.
Interface (Ports & Jacks) Item Description Mini-IEEE 1394a Port This allows high-speed connection to various peripheral devices, e.g. external disk drives and digital cameras (see note below). IEEE 1394a The Mini-IEEE 1394 ports only support SELF POWERED IEEE 1394 devices. A RJ-45 LAN Jack This port supports LAN (Network) functions. Note: Broadband (e.g. ADSL) modems usually connect to the LAN port.
Interface (Ports & Jacks) Item Description USB 2.0/1.1 Ports These USB (Universal Serial Bus) 2.0 compatible ports (USB 2.0 is fully USB 1.1 compliant) are for low-speed peripherals such as keyboards, mice or scanners, and for high-speed peripherals such as external HDDs, digital video cameras or high-speed scanners etc.
Interface (Ports & Jacks) A A - 6 Interface (Ports & Jacks)
Control Center Appendix B: Control Center Overview The following chapter will give a quick description of the functions of the Control Center. The Control Center gives quick access to frequently used controls, power management features and enables you to quickly turn modules on/off. Click the Control Center icons to toggle the appropriate function, or hold the mouse button down and move the slider where applicable. Certain functions will automatically be adjusted when a power mode is selected.
Control Center Power Modes You can set a Power Mode by clicking the appropriate icon at the top of the Control Center. Each power mode will affect screen brightness, Touchpad and PC camera power etc. You can click a Control Center icon to set an overall power mode and then click individual icons in the Control Center to power on/off the Touchpad and PC camera.
Control Center Power Status The Power Status icon will show whether you are currently powered by the battery, or by the AC/DC adapter plugged in to a working power outlet. The power status bar will show the current battery charge state. Brightness The Brightness icon will show the current screen brightness level. You can use the slider to adjust the screen brightness or the Fn + F8/F9 key combinations, or use the Fn+ F2 key combination to turn off the LED backlight (press any key to turn it on again).
Control Center Sleep Click the Sleep button to bring up the Hibernate or Sleep buttons, and click either button to have the computer enter the appropriate power-saving mode (see “Power-Saving States” on page 3 - 6). Display Switch Click the Display Switch button to access the menu (or use the priate attached display mode. + P key combination) and select the appro- Time Zone Clicking the Time Zone button will access the Date and Time Windows control panel.
Video Driver Controls Appendix C: Video Driver Controls The basic settings for configuring the LCD are outlined in “Video Features” on page 1 - 40. Video Driver Installation Video Card Options Make sure you install the drivers in the order indicated in Table 4 - 1, on page 4 - 3. Insert the Device Drivers & Utilities + User’s Manual disc and click Install Drivers (button). Note that card types, specifications and drivers are subject to continual updates and changes.
Video Driver Controls NVIDIA® Optimus™ Technology iGPU or dGPU Most notebook computers come with either a discrete or integrated graphics solution. Note the NVIDIA control panel refers to Highperformance NVIDIA processor (which is the discrete GPU) and Integrated graphics (which is the integrated GPU). Discrete graphics solutions feature a dedicated Graphics Processing Unit (GPU) which are capable of playing games, watching HD video or running GPU-based applications.
Video Driver Controls How Optimus Technology works When the system is powered up and is displaying just the desktop, the dGPU will be powered off. In this case the system is running in the same way as a system without a discrete graphics solution. However when an application that requires use of the dGPU is run (e.g, a game or HD Video), the dGPu is powered on and takes over the processing duties. If the program is closed, then the dGPU will be powered back down again until required.
Video Driver Controls Intel® Dynamic Video Memory Technology Intel® DVMT automatically and dynamically allocates as much (up to 1748MB) system memory (RAM) as needed to the integrated video system (the video driver must be installed). DVMT returns whatever memory is no longer needed to the operating system.
Video Driver Controls Intel® Graphics & Media Control Panel Advanced video configuration options are provided by the Intel® HD Graphics Control Panel. To access the control panel see below and overleaf: 1. Click the Intel® Graphics and Media Control Panel icon in the Start screen.
Video Driver Controls OR 2. Right-click the Desktop and select Graphics Properties from the menu. OR 3. 4. 5. Click Advanced settings in the Screen Resolution control panel in Windows. Click the Intel(R) HD Graphics Control Panel tab and click Graphics Properties (button). Double-click the Intel(R) HD Graphics control panel in the Windows Control Panel.
Video Driver Controls You may make changes to any of the graphics properties by clicking the appropriate menu panel and adjusting the settings on the right.
Video Driver Controls Sub-Menus Some of the menu panels will also have sub-menus (in the top left corner of the menu alongside the icon ) to display further configuration options.
Video Driver Controls Display Click either Display Settings or Color to make display adjustments, including configuration for any attached external displays. Multiple Display At least one other display must be attached in order to view multiple display selection options.
Video Driver Controls Multiple Display Click the Display menu at the top of the screen to display the sub-menus. The Multiple Displays menu allows you to configure the display mode of any attached displays (see “Attaching Other Displays” on page C - 21). At least one other display must be attached in order to view multiple display selection options.
Video Driver Controls The Audio sub-menu allows you to configure the capability mode of any attached displays if applicable (i.e. the attached display supports audio). Enable Audio Without Video to keep audio on when the display blanks out for power saving purposes.
Video Driver Controls 3D This menu allows you to choose how 3D images are displayed. Quality displays the most detail, Balanced provides better computer performance with good quality and Custom allows you to configure the Anisotropic Filtering, Vertical Sync and Anti-Aliasing features to your preferences. Click Apply to save changes.
Video Driver Controls Options Options allows you to Customize Hot Keys (for opening the application, rotating the display, scaling etc.,) to your preferences. Click Apply to save changes.
Video Driver Controls Preferences Click the Options menu at the top of the screen to display the sub-menus. The Information Center provides details on System Information, the Built-In Display and any attached displays. Go to the Preferences sub-menu in Options to configure the preferences for the Intel® HD Graphics Control Panel. Make sure you turn Tray Icon On to display the Intel® HD Graphics Control Panel icon in the notification area of the taskbar (as below).
Video Driver Controls Video The Video Profiles menu allows you to brighten or darken movies, or to switch to vivid colors. Click Basic or Advanced to adjust the video settings based on the Application Settings or Driver Settings. The Preview image will display a sample image using the current settings. You can Save Profile and name the Profile to recall the settings at any time. Click Apply to save changes.
Video Driver Controls Click the Video menu at the top of the screen to display the sub-menus.The Image Enhancement menu allows you to adjust the Sharpness, Skin Tone Enhancement, Noise Reduction etc.Click Apply to save changes.
Video Driver Controls The Image Scaling and Gamut Mapping menus allow you to adjust these items.
Video Driver Controls Power Choose a Power Plan for when the computer is Plugged in or On battery. When turned on, the Display Power Saving Technology (which adjusts the backlight intensity) battery settings may be adjusted by means of the slider towards Maximum Quality or Maximum Battery. Click on Apply to save changes.
Video Driver Controls Support Click Support and select an item from the menus to bring up the help and support topics. You will need to be connected to the Internet to access the key resource links.
Video Driver Controls Display Devices & Options Note that you can use external displays connected to the HDMI-Out port and/or external display port/mini display port. See your display device manual to see which formats are supported. Attaching Displays When you first attach an external display you may find that the desktop does not occupy the full screen area. Use either the display’s auto adjust/configure controls, or the Intel(R) HD Graphics Control Panel to configure the full screen display.
Video Driver Controls Attaching Other Displays To Clone Displays: 1. 2. 3. 4. 5. Attach your external display to the display port/mini display port/HDMI-Out port, and turn it on. Go to the Intel(R) HD Graphics Control Panel control panel and click Display > Multiple Displays (sub-menu). Click Clone from the Select Multiple Display Mode menu. Click Apply, and OK to confirm the settings change. You can select the displays to be used from the Select Active Displays menu.
Video Driver Controls To Enable Extended Mode: 1. Display Settings Extended Desktop 2. You can have different Colors, Screen Area and Monitor Refresh Rates for each display device provided your monitor can support them. 3. 4. Attach your external display to the display port/mini display port/HDMI-Out port, and turn it on. Go to the Intel(R) HD Graphics Control Panel control panel and click Display > Multiple Displays (sub-menu). Click Extended from the Select Multiple Display Mode menu.
Video Driver Controls Attaching Other Displays - Devices (Charms Bar) You can configure attached displays from Devices (in the Windows 8 Charms Bar). 1. 2. 3. 4. Attach your external display to the display port/mini display port/HDMI-Out port, and turn it on. Go the Charms Bar and select Devices. Click Second Screen. Click on any one of the options from the menu to select Duplicate, Extend or a Single (PC Screen only or Second Screen only) display.
Video Driver Controls Configuring an External Display In Windows 1. 2. 3. 4. Attach your external display to the display port/mini display port/HDMI-Out port, and turn it on. Go to the Screen resolution control panel (see page 1 - 32) in the Desktop app. Click the Detect button. The computer will then detect any attached displays.
Video Driver Controls 5. You can configure the displays from the Multiple Displays menu. Figure C - 20 Screen Resolution Multiple Display Options • Duplicate these displays - Shows an exact copy of the main display desktop on the other display(s) • Extend these displays - Treats both connected displays as separate devices • Show desktop only on 1/2 - Only one of your displays is used.
Video Driver Controls NVIDIA Control Panel To access the GeForce..... control panel from the desktop; rightclick the desktop, then click NVIDIA Control Panel. C NVIDIA Control Panel More advanced video configuration options are provided in the NVIDIA Control Panel tab. 1. 2. Go to the Control Panel. Double-click NVIDIA Control Panel (click to view the control panel in either Large icons or Small icons if you are in Category view).
Video Driver Controls The NVIDIA Control Panel provides additional video configuration controls and tools which allow quick access to features such as image settings, 3D Settings and video configuration. Navigating the Control Panel Navigate through the control panels in much the same way as you would a web page. Click on the sub-heading tasks in the left menu (and on the highlighted links) for information. Use the buttons on the top left to go back, forward etc.
Video Driver Controls Display GPU Activity Icon Click to enable Display GPU Activity Icon in the Notification Area to quickly access the GPU Activity monitor from the taskbar. C Optimus™ Customization Options One of the most important aspects of Nvidia® Optimus™ technology is that it will switch between the integrated GPU and discrete GPU seamlessly and automatically, and does not require any input from the user.
Video Driver Controls 3. 4. 5. 6. Close the NVIDIA Control Panel. Find the executable file icon of the application you want to run. Right-click the icon and select Run with graphics processor from the context menu. Select either High-performance NVIDIA processor (dGPU) or Integrated graphics (iGPU) to run the program with the selected GPU.
Video Driver Controls Global Settings Global settings allows you to set the preferred graphics processor for overall use. Ideally this would be the iGPU for battery life, but this can be set to the dGPU if preferred. 1. 2. 3. 4. 5. Go to the NVIDIA Control Panel. Click Manage 3D Settings (3D Settings) and select Global Settings (tab). Select either Integrated graphics (iGPU) or High performance NVIDIA Processor (dGPU) from the drop-down menu. Click the Setting menu items to select any options required.
Video Driver Controls Program Settings Program settings allows you to make specific adjustments for installed applications. 1. 2. 3. 4. 5. 6. Go to NVIDIA Control Panel. Click Manage 3D Settings (3D Settings) and select Program Settings (tab). Select a program to customize from the drop-down menu, or click Add to add any program that does not appear in the menu. Select the preferred graphics processor for the program from the drop-down menu. Click the Setting menu items to select any options required.
Video Driver Controls Set PhysX® Configuration NVIDIA® PhysX® is a physics engine that can use the GPU to accelerate game and 3D application performance. You can select the GeForce video card or CPU as a PhysX® processor, or configure the computer to auto-select a PhysX® processor (recommended default setting). 1. 2. 3. 4. Go to NVIDIA Control Panel. Click Set PhysX configuration. Click to Select a PhysX processor from the menu; Auto-select (recommended) is the default setting.
Video Driver Controls Video Settings Click the sub-menus under Video to adjust the video color or image settings.
Video Driver Controls Volume Adjustment The sound volume level can be set using the volume control in the Settings menu in the Charms Bar. HDMI Audio Configuration HDMI (High-Definition Multimedia Interface) carries both audio and video signals. In some cases it will be necessary to go to the Sound control panel and manually configure the HDMI audio output as per the instructions below. 1. 2. 3. 4. C Go to the Control Panel.
Video Driver Controls 5. 6. Adjust the HDMI settings from the control panel tabs. Click OK to close the Sound control panel.
Video Driver Controls Other Applications If you are using a third party application to play DVDs etc. from any attached DVD device, you will need to consult the application’s documentation to see the appropriate audio configuration (the application must support digital to analog translation). HDMI Notes • Connect a device with HDMI support to the HDMI-Out port BEFORE attempting to play audio/video sources through the device.
Specifications Appendix D: Specifications Latest Specification Information The specifications listed in this Appendix are correct at the time of going to press. Certain items (particularly processor types/ speeds and CD/DVD device types) may be changed, updated or delayed due to the manufacturer's release schedule. Check with your distributor/supplier for details.
Specifications Processor Memory Video Adapter Options For Models A, B, D & E Only: Intel® Core™ i7-4930MX (3.00GHz) Extreme Edition Processor 8M L3 Cache, 22nm (22 Nanometer), DDR3L-1600MHz, TDP 57W Dual Channel DDR3L Intel® Integrated GPU with NVIDIA® GeForce Video: For All Models: Intel® Core™ i7-4900MQ (2.
Specifications For All Models: NVIDIA® GeForce GTX 770M PCIe * 16 Video Card 3GB GDDR5 Video RAM Microsoft DirectX® 11 compatible NVIDIA PhysX™ NVIDIA CUDA™ Technology NVIDIA® Optimus 1.2 Technology NVIDIA® GeForce GTX 765M PCIe * 16 Video Card 2GB GDDR5 Video RAM Microsoft DirectX® 11 compatible NVIDIA PhysX™ NVIDIA CUDA™ Technology NVIDIA® Optimus 1.2 Technology Storage For All Models: Two mSATA Solid State Drives (SSDs) with SATA (Serial) Interface with RAID Level 0/1 Support (Factory Option) One 12.
Specifications Indicators Security Communication LED Indicators - Power/Suspend, Battery, HDD/ODD, Airplane Mode, GPU Mode, Num Lock, Caps Lock, Scroll Lock, Camera Security (Kensington® Type) Lock Slot BIOS Password Fingerprint Reader Module (Factory Option) Built-In 10/100/1000Mb Base-TX Ethernet LAN Interface Slots One USB 2.0 Port Three USB 3.0 Ports (Note: One powered USB3.0 port (AC/DC) One eSATA Port (SATA USB 3.0 Combo) One Mini-IEEE1394a Port One Display Port 1.2 One Mini Display Port 1.
Specifications Operating System Windows® 8 Features Rubber Painted Style (Models A, B & E) Painted Style (Model C) Al-Alloy Plate (Model D) Intel® Rapid Start Technology Intel® Smart Response Technology Intel® Anti-Theft Technology Power Management Supports Wake on LAN Supports Wake on USB Supports Wake on RTC Alarm Power Removable 8 Cell Smart Lithium Ion Battery Pack 76.96WH Model A & B: Full Range AC/DC Adapter – AC in 100 240V, 50 - 60Hz DC Output 19V, 9.5A; 19.5V, 9.2A & 19V, 9.
Specifications D D - 6
