EuroForm IPDS 100 User Guide
EuroForm IPDS 100 User Guide Caution DIMM boards and your printer formatter board can be damaged by small amounts of static electricity. When handling a DIMM or other board, wear an antistatic wrist strap connected to the metal frame of the printer (or to your antistatic system). During installation, to prevent generation of static electricity, avoid moving about the work area. Warranty The information contained in this document is subject to change without notice.
Table of Contents Table of Contents Table of Contents ..............................................................................................................................3 Introduction ....................................................................................................................................... 6 About this Manual ....................................................................................................................... 6 System Requirements ..................
EuroForm IPDS 100 User Guide Remote .......................................................................................................................................... 31 Diagnostic Tool............................................................................................................................... 36 Requirements.............................................................................................................................. 36 IPDS 100 Debug Tracer Windows................
Table of Contents Appendix D. Glossary....................................................................................................................
EuroForm IPDS 100 User Guide Introduction About this Manual Thank you for purchasing the EuroForm IPDS 100 DIMM providing emulation support for the IBM Intelligent Printer Data Stream (IPDS) for your hp LaserJet printer. Using the hp JetDirect Card your printer becomes an IBM host workstation printer capable of printing IPDS documents from an AS/400, System/370, or System/390. This document describes the configuration of the EuroForm IPDS 100 solution.
Introduction Support If you encounter any problems or if you have further questions please contact your local reseller or send an e-mail to support@euroform.com. EuroForm IPDS 100 firmware updates, updates to this User Guide, and other relevant information may be found at http://www.euroform.com/ipds100. Please contact hp for printer or JetDirect print server firmware updates.
EuroForm IPDS 100 User Guide Configuration Parameters Resource Resolution This option defines the supported font and image resolution that the EuroForm IPDS 100 reports back to the IBM host system. 240 dpi Print at 240 pel resolution 300 dpi* Print at 300 pel resolution 600 dpi Print at 600 pel resolution If for example your are replacing IBM 3812/16 printers and the resources such as fonts and images on the IBM host only is available in 240 dpi, then this option should be set to 240 dpi.
Configuration Parameters Default Font Size Selects the default characters per inch (CPI) to be used by the EuroForm IPDS 100 when the IBM host does not send a CPI value at the start of a job. 5.0 5 characters per inch 10.0* 10 characters per inch 12.0 12 characters per inch 13.3 13.3 characters per inch 15.0 15 characters per inch 16.7 16.7 characters per inch 20.
EuroForm IPDS 100 User Guide 0 AutoSelect If letter, legal or ledger paper size is found in any of the input trays the CPID is set to 1140 otherwise it is set to 1148 1 Chai Specified Use CPID selected via the web interface 37 US/Can-37 US, Can, Dutch, Brazilian, Portuguese 273 Aus/Ger-273 Austria, Germany 274 Belgian-274 Belgian 277 Dan/Nor-277 Danish, Norwegian 278 Fin/Swe-278 Finnish, Sweden 280 Italian-280 Italian 282 Portuguese-282 Portuguese 284 Spanish-284 Spanish 285 U
Configuration Parameters 0 AutoSelect If letter, legal or ledger paper size is found in any of the input trays the CPID is set to 1140 otherwise it is set to 1148 37 US/Can-37 US/Canadian 38 US ASCII-38 US ASCII (as EBCDIC) 259 Sym Set 7-259 Symbols, Set 7 260 Can/Fr-116 Canadian French – 116 273 Aus/Ger-273 Austria, Germany 274 Belgian-274 Belgian 275 Brazilian-275 Brazilian 276 Can/Fr-276 Canada (French) 277 Dan/Nor-277 Danish, Norwegian 278 Fin/Swe-278 Finnish, Sweden 28
EuroForm IPDS 100 User Guide 384 Brz Pub-384 Brazilian Publishing 385 Can/Fr Pub-385 Canadian French Pub. 386 Dan/Nor Pub-386 Danish/Norwegian Pub. 387 Fin/Swe Pub-387 Finnish, Swedish Pub. 388 Fr Pub-388 French Publishing 389 Italian-389 Italian Publishing 390 Japan Pub-390 Japanese Publishing 391 Por Pub-391 Portuguese Publishing 392 Spanish Pub-392 Spanish Publishing 393 Lt Am Sp Pub-393 Latin Amer. Spanish Pub.
Configuration Parameters 862 Hebrew PC-862 Hebrew PC 863 Can/Fr PC-863 Canadian French PC 864 Arabic PC-864 Arabic PC 865 Nordic PC-865 Nordic PC 866 Cyr #2 PC-866 Cyrillic #2 PC 869 Greek PC-869 Greek PC 870 Lt 2 Multi-870 Latin 2 Multilingual 871 Icelandic PC-871 Icelandic PC 875 Greek-875 Greek 876 OCR-A ASCII-876 OCR-A ASCII 877 OCR-B ASCII-877 OCR-B ASCII 880 Cyr Multi-880 Cyrillic Multilingual 892 OCR-A-892 OCR-A 893 OCR-B-893 OCR-B 897 Japan PC-897 Japan PC
EuroForm IPDS 100 User Guide 1028 Hebrew Pub-1028 Hebrew Publishing 1029 Ara Ext-1029 Ara. Ext ISO/ASCII 8 bit 1038 Sym, Adobe-1038 Symbols, Adobe ASCII 1039 GML Lst Sym-1039 GML List Symbols 1041 Jp Ext PC-1041 Japanese Extended PC 1046 Ara Ext-1046 Ara. Ext ISO/ASCII 8 bit 1068 Txt Num Spc-1068 Txt with Numeric Spacing 1069 Lt 4 EBCDIC-1069 Latin 4 EBCDIC 1087 Sym Adobe-1087 Symbols, Adobe 1091 Sym Mod s 7-1091 Symbols, Modified Set 7 1092 Sym Mod-1092 Symbols Mod.
Configuration Parameters Version 1* Use version 1 of the selected code page. Version 0 Use version 0 of the selected code page. Font Capture Note: This option only displays if a hard disk is installed in the printer. This option controls the capturing of eligible bitmap fonts (LF1 format) and eligible outline fonts (LF3 format) from the host by the IPDS emulation.
EuroForm IPDS 100 User Guide Whole Page* The printable area is some millimetres inside the physical page dependent on the specific HP LaserJet model. This printable area is reported to the host. Clipping occurs if data is printed outside the printable area. All four edges will be clipped. Trim The printable area is some millimetres inside the physical page dependent on the specific HP LaserJet model. This printable area is reported to the host.
Configuration Parameters Page Counter Action This option selects the method used for updating IPDS page counters. Regular Update* Jam and stacked page counters are updated when pages are printed. Early Update All page counters are updated when they are processed but not printed. Pages may be lost if power or printer failure occurs. However, selecting this option may increase printing speed. Note: When Early Update is selected, Intervention Required messages are not reported to the IPDS Host.
EuroForm IPDS 100 User Guide Intervention Required Reporting This option defines if the emulation should report Intervention Required events to the IBM host. Types of Intervention Required events include paper jam, paper out, cover open or offline situations. These types of events mean that the printer is not ready to print. Yes* Report Intervention Required events to the IBM host. No Do not report Intervention Required messages to the IBM host.
Configuration Parameters If an IPDS Number is mapped (used) twice, then the last mapping in the list will be the active one. Note: For the Source Mapping to work correctly, the MEDIA TYPE for each input tray must be set differently. The only time you would set the MEDIA TYPE the same value is when you want to link the input trays.. For setting up the MEDIA TYPE please refer to the specific hp LaserJet printer documentation.
EuroForm IPDS 100 User Guide Margins may be adjusted for all input trays and feeders using the four Default Margins values: Margin Front Top, Margin Front Left, Margin Back Top and Margin Back Left. Front and Back refer to the front page and the back page of a sheet of paper printed in duplex. Additional adjustments may be made to an individual tray or feeder using the Margins Option for the specific tray or feeder.
Font Capturing Font Capturing The Font Capture option allows capture of eligible bitmap fonts (LF1 format) and eligible outline fonts (LF3 format) received from the host. These fonts will be stored (captured) on the printer’s hard disk. Fonts intended for capturing must be marked eligible for capture on the host before they will be downloaded to the printer for capture. Fonts, which are resident on the printer, will not be downloaded for capture by the host.
EuroForm IPDS 100 User Guide Capturing Fonts From an AS/400 AS/400 Program Requirements PSF/400 V4R2 or later is required for making fonts eligible for capture. Making Fonts Eligible for Capture on the AS/400 Two steps are required on the AS/400 to capture fonts. These are: 1. Make the font resource eligible for capture. To mark a font resource eligible for capture, set FNTCAPTURE to *YES.
Font Capturing Capturing Fonts From a Mainframe Host Mainframe Program Requirements Font capture is supported by PSF/MVS 2.2.0 with APAR OW08340 and PSF/VSE 2.2.1 with APAR DY43969. Making Fonts Eligible for Capture on a Mainframe Note: The procedures/documentation below are for OS390/MVS/PSF platform. The following are the software release requirements for font capture feature within this platform.
EuroForm IPDS 100 User Guide // TIME=1440 //*** NOTE: USE THIS JOB TO PRINT SHORT FONT STATUS MARKINGS ONLY **** //*** NOTE: CHANGE DSN LINE 13 (IN1 STATEMENT) TO MATCH YOUR FONTLIB * //******************************************************************** //STEP1 EXEC PGM=APSRMARK //SYSPRINT DD SYSOUT=J //* //IN1 DD UNIT=3390,DSN=SYS1.FONTLIBB,DISP=SHR,VOL=SER=OS3R7A //SYSIN DD * INDD=IN1,MEMBER=ALL,REPORT,SHORT /* Note: Change report type to "LONG" for font detailed report (replace the "SHORT" option).
Font Capturing INDD=IN1,OUTDD=OUT1,MEMBER=T1V10037,PUBLIC INDD=IN1,OUTDD=OUT1,MEMBER=C08400B0,PUBLIC /* Note: If you want to mark all fonts in a particular font library "PUBLIC" you can create a new font library, copy, and mark all fonts as "PUBLIC" at the same time. The following is a sample of the JCL commands to copy and mark all fonts "PUBLIC" to a new library.
EuroForm IPDS 100 User Guide To select font capture from the printer definition member, add the "CHARS" option as follows to your PSF printer member.
Configuration Options Configuration Options Overview The configuration for the IPDS solution is stored in a XML file located on the EuroForm IPDS 100 DIMM. Extensible Markup Language (XML) is a universal format for data and has become an industrial standard today. The reason for storing the IPDS configuration in a XML document is therefore obviously. The EuroForm IPDS 100 is provided with three options for altering the configuration of the IPDS solution on your HP LaserJet printer.
EuroForm IPDS 100 User Guide The Web Interface is implemented as a ChaiService running on the printer’s web server and can be accessed by typing the printers IP address in a standard web browser. Please see System Requirements in the “EuroForm IPDS 100 Getting Started Guide” for more information on compatible web browsers. If the printers IP Address e.g. is 192.168.0.97 simply type http://192.168.0.97/ in your browsers address bar.
Configuration Options The parameters are grouped into the four sub web pages: • IPDS Settings • Source Mapping • Target Mapping • Margins IPDS Settings is the IPDS emulation dependent parameters whereas Source Mapping, Target Mapping and Margins are printer specific settings for the IPDS solution. The Web Interface Environment provides an Online Help system. All parameters marked with a question mark have Online Help available. This will give you additional information about the actual parameter.
EuroForm IPDS 100 User Guide Please refer to the Online Help or the previous chapter about Configuration Parameters for help. Target Mapping This web page gives the possibility to add, edit or delete Target Mapping to the IPDS configuration. Please refer to the Online Help or the previous chapter about Configuration Parameters for help. Margins This web page gives the possibility to add, edit or delete Tray Margins to the IPDS configuration.
Configuration Options Furthermore, here you can reset the actual IPDS configuration to the factory default settings as well as remove all captured fonts stored on the printer hard disk. The factory default settings should be able to run in any IPDS environment with minimum features and is thereby a good starting point if nothing is working and you have to start all over. Documentation This web page contains access to documentation such as the EuroForm IPDS 100 User Guide.
EuroForm IPDS 100 User Guide Download of the IPDS configuration file The XML document containing the IPDS configuration can be retrieved from the EuroForm IPDS 100 DIMM either by using the HP Printer Disk Manager (HPPDM) or by browsing the following URL: http:///hp/device/euroform/ipds100/xml/ipds100.xml When browsing, the XML document will be parsed and displayed. To obtain it as file format choose File menu and save it as XML document to your local file system.
Configuration Options When you send the e-mail to one or more recipients (printers) the Remote Environment will receive the e-mail and write the XML document to the EuroForm IPDS 100 DIMM and the IPDS configuration will be updated. PJL-job The PJL-job configuration update option only requires you to have some way to copy the PJL job to the printer. We recommend that you use EuroForm IPCopy (available from http://www.euroform.com/ipds100). This update option only allows you to update one printer at a time.
EuroForm IPDS 100 User Guide In the template below the tags “[ESC]” should be replaced by an actual escape character. (ASCII character 27) Remote IPDS 100 configuration PJL-Job template [ESC]%-12345X@PJL JOB NAME="IPDS 100 CONFIGURATION UPDATE" @PJL ENTER LANGUAGE=IPDS100_CONFIG [Here the configuration XML-file should be inserted] [ESC]%-12345X@PJL EOJ NAME="IPDS 100 CONFIGURATION UPDATE" [ESC]%-12345X Below is shown an example of a PJL-job.
Configuration Options 100 0 0 0 0 4 [ESC]%-12345X@PJL EOJ NAME="IPDS 100 CONFIGURATION UPDATE" [ESC]%-12345X To copy the PJL-job to the printer via EuroForm IPCopy you do the following: 1. Get the IPCopy utility tool from the EuroForm Web site. 2. Open a DOS Window 3.
EuroForm IPDS 100 User Guide Diagnostic Tool Requirements The following is required to be able to run the IPDS 100 Debug Tracer: • Java Plug-In 1.4. • Microsoft Internet Explorer 5.0 or later. IPDS 100 Debug Tracer Windows When the IPDS 100 trace tool is started the following screen will appear: This screen appears because the debug tool is contained in a signed jar file. In order to get the tracer to work you’ll need to grant the applet access to perform certain operations on your local workstation.
Diagnostic Tool Hereafter the main trace window will appear: The main tracer window contains the following elements: Status area: The status area will show the current status of the IPDS 100 Tracer. It will also be used to display error messages if an error should occur. Trace file size: This field will show the current size of the traced data. Trace time: The field will show the time the trace has been active. Start Trace: Clicking on this button will start the tracer.
EuroForm IPDS 100 User Guide Browse: This tab takes you to the browse window, which will allow you to view the different configuration files. How To Trace The following will explain how to trace IPDS data from the IPDS 100 solution. You should only trace on a printer that has just been rebooted. If you are trying to trace on a printer that has been printing, the trace tool might not be able to trace. This can be caused by an AS/400 that has not closed the connection to the printer. 1.
Diagnostic Tool 9. Wait until the print job has completed before stopping the tracer. During the tracing process you will see the amount of received data increase. (Up to about 200KB of data has to be sent before this counter is updated though). 10. After you have stopped the trace, please forward the zip file to us at support@euroform.
EuroForm IPDS 100 User Guide PSF/MVS AFP printing using TCP/IP This chapter provides information on how to create MVS definitions for printing from PSF/MVS via TCP/IP. The following topics are addressed: JES printer statements PSF start-up procedure Once these parameters have been configured, and the basic TCP/IP installation of the hp LaserJet printer with the EuroForm IPDS 100 has been completed, direct AFP/IPDS printing from PSF/MVS will be possible. Requirements: • PSF/MVS version 2 Release 2.
PSF/MVS AFP printing using TCP/IP Example of PSF/MVS JES2 printer definition: PRT420 FSS=FSS1,MODE=FSS,PRMODE=(LINE,PAGE), CLASS=A,UCS=0,SEP,NOSEPDS,CKPTPAGE=100,DRAIN,WS=(R,Q/FCB) PSF/MVS start-up procedure: //PSF4 PROC //STEP01 EXEC PGM=APSPPIEP,REGION=1750K //JOBHDR OUTPUT PAGEDEF=V06483, /* JOB SEPARATOR PAGEDEF */ // FORMDEF=A10110,CHARS=GT15 /* JOB SEPARATOR FORMDEF */ //JOBTLR OUTPUT PAGEDEF=V06483, /* JOB SEPARATOR PAGEDEF */ // FORMDEF=A10110,CHARS=GT15 /* JOB SEPARATOR FORMDEF */ //DSHDR OUTPUT
EuroForm IPDS 100 User Guide // GT12,GT15,GT10), // PIMSG=YES, // DATACK=BLOCK, // TRACE=NO, // FAILURE=WCONNECT, // TIMEOUT=REDRIVE, // DISCINTV=30, // MGMTMODE=IMMED, // IPADDR=‘192.168.0.97’ // PORTNO=9100 //PRT420 ENDCNTL /* /* /* /* /* /* /* /* /* /* DEFAULT FONT SET */ ACCUMULATE DATA SET MESSAGES*/ REPORT ALL DATA-CHECK ERRORS*/ CREATE INTERNAL TRACE */ ACTION ON PRINTER FAILURE */ PSF ACTION ON TIMEOUT */ DISCONNECT INTERVAL IN SECS.
PSF/400 AFP printing using TCP/IP PSF/400 AFP printing using TCP/IP This chapter provides configuration guidelines for OS/400 using TCP/IP. The versions differ somewhat in the set-up. For the different OS/400 versions, use the cross-references below: AS/400 settings for version 3.1 AS/400 settings for version 3.2 AS/400 settings for version 3.6 AS/400 settings for version 3.7 AS/400 settings for version 4.1 AS/400 settings for version 4.2 AS/400 settings for version 4.3 AS/400 settings for version 4.4, 4.
EuroForm IPDS 100 User Guide Note: The IPDS port for the hp JetDirect Card is port 9100. AS/400 settings for version 3.1 To configure IPDS printing on OS/400 V3R1, you must use two commands: - CRTDEVPRT - WRKAFP2 Configuring PSF with CRTDEVPRT on V3R1 Note: Where the text says , you should write the name that you want to assign to your specific hp LaserJet printer with the EuroForm IPDS 100 DIMM.
PSF/400 AFP printing using TCP/IP A completed screen looks like the following example: Display Device Description Page 1 5763SS1 V3R1M0 940909 BLDSYS1 04/04/02 12:55:08 Device description . . . . . . . : Option . . . . . . . . . . . . . : Category of device . . . . . . . : Automatically created . . . . . .: Device class . . . . . . . . . . : Device type . . . . . . . . . . .: Device model . . . . . . . . . . : Advanced function printing . . . : AFP attachment . . . . . . . . . : Online at IPL . . . . . . .
EuroForm IPDS 100 User Guide A printout should look like the following: QPQXWAFP -------DEVD IPDSPASTHR TCPIP RMTSYS PORT ACTTMR INACTTMR SBP PSC DRF DRR EDGSNSTV *YES *YES 192.168.0.97 9100 *NOMAX *SEC15 *NO *YES *NO *NO *NO Then do the following: Ping the IP address to verify communication with the printer: PING ’192.168.0.97’ Vary the printer on: VRYCFG CFGTYPE(*DEV) STATUS(*ON) Start the print writer: STRPRTWTR AS/400 settings for version 3.
PSF/400 AFP printing using TCP/IP Configuring PSF with CRTDEVPRT on V3R2 Note: Where the text says , you should write the name that you want to assign to your specific hp LaserJet printer with the EuroForm IPDS 100 DIMM..
EuroForm IPDS 100 User Guide Configuring AFP with CRTPSFCFG on V3R2 On the AS/400 command line, enter a command in the form: CRTPSFCFG PSFCFG() IPDSPASTHR(*YES) RLSTMR(*SEC15) TEXT(EUROFORM IPDS 100) RMTLOCNAME('192.168.0.97) PORT(9100) A completed screen looks like this: PSF configuration . . . . . . . . . Library . . . . . . . . . . . . . . User resource library . . . . . . . IPDS pass through . . . . . . . . . Activate release timer . . . . . . Release timer . . . . . . . . . . .
PSF/400 AFP printing using TCP/IP AS/400 settings for version 3.6 To configure IPDS printing on OS/400 V3R6, you must use two commands: - CRTDEVPRT - WRKAFP2 Configuring PSF with CRTDEVPRT on V3R6 Note: Where the text says , you should write the name that you want to assign to your specific hp LaserJet printer with the EuroForm IPDS 100 DIMM.
EuroForm IPDS 100 User Guide A completed screen looks like the following example: Display Device Description Page 1 5763SS1 V3R6M0 940909 BLDSYS1 04/04/02 10:05:20 Device description . . . . . . . : DEVD Option . . . . . . . . . . . . . : OPTION *ALL Category of device . . . . . . . : *PRT Automatically created . . . . . .: NO Device class . . . . . . . . . . : DEVCLS *RMT Device type . . . . . . . . . . .: TYPE *IPDS Device model . . . . . . . . . . : MODEL 0 Advanced function printing . . .
PSF/400 AFP printing using TCP/IP A printout should look like the following: QPQXWAFP -------DEVD IPDSPASTHR TCPIP RMTSYS PORT ACTTMR INACTTMR SBP PSC DRF DRR EDGSNSTV *YES *YES 192.168.0.97 9100 *NOMAX *SEC15 *NO *YES *NO *NO *NO Then do the following: Ping the IP address to verify communication with the printer: PING ’192.168.0.
EuroForm IPDS 100 User Guide AS/400 settings for version 3.7 To configure IPDS printing on OS/400 V3R7, you must use two commands: - CRTDEVPRT - CRTPSFCFG Configuring PSF with CRTDEVPRT on V3R7 Note: Where the text says , you should write the name that you want to assign to your specific hp LaserJet printer with the EuroForm IPDS 100 DIMM.
PSF/400 AFP printing using TCP/IP A completed screen looks like this: Display Device Description Page 1 5716SS1 V3R7M0 961108 BLDRB1 04/04/02 11:02:51 Device description . . . . . . . . : DEVD Option . . . . . . . . . . . . . . : OPTION Category of device . . . . . . . . : Device class . . . . . . . . . . . : DEVCLS Device type. . . . . . . . . . . . : TYPE Device model . . . . . . . . . . . : MODEL LAN attachment . . . . . . . . . . : LANATTACH User-defined object. . . . . . . . : USRDFNOBJ Library. . . .
EuroForm IPDS 100 User Guide A completed screen looks like this: PSF Configuration Information Page PSF configuration. . . . . . . . . Library. . . . . . . . . . . . . . User resource library. . . . . . . IPDS pass through. . . . . . . . . Activate release timer . . . . . . Release timer. . . . . . . . . . . Restart timer. . . . . . . . . . . SNA retry count. . . . . . . . . . Delay time between retries . . . . Blank page . . . . . . . . . . . . Page size control. . . . . . . . . Resident fonts . . . . . .
PSF/400 AFP printing using TCP/IP AS/400 settings for version 4.1 To configure IPDS printing on OS/400 V4R1, you must use two commands: - CRTDEVPRT - CRTPSFCFG Configuring PSF with CRTDEVPRT on V4R1 Note: Where the text says , you should write the name that you want to assign to your specific hp LaserJet printer with the EuroForm IPDS 100 DIMM.
EuroForm IPDS 100 User Guide A completed screen looks like this: Display Device Description Page 1 5716SS1 V4R1M0 971108 BLDRB1 04/04/02 12:12:34 Device description . . . . . . . . : DEVD Option . . . . . . . . . . . . . . : OPTION Category of device . . . . . . . . : Device class . . . . . . . . . . . : DEVCLS Device type. . . . . . . . . . . . : TYPE Device model . . . . . . . . . . . : MODEL LAN attachment . . . . . . . . . . : LANATTACH User-defined object. . . . . . . . : USRDFNOBJ Library. . . . . . .
PSF/400 AFP printing using TCP/IP A completed screen looks like this: PSF Configuration Information PSF configuration . . . . . . Library . . . . . . . . . . . User resource library . . . . IPDS pass through . . . . . . Activate release timer. . . . Release timer . . . . . . . . Restart timer . . . . . . . . SNA retry count . . . . . . . Delay time between retries. . Blank page. . . . . . . . . . Page size control . . . . . . Resident fonts. . . . . . . . Resource retention. . . . . . Edge orient . . . . .
EuroForm IPDS 100 User Guide AS/400 settings for version 4.2 To configure IPDS printing on OS/400 V4R2, you must use two commands: - CRTDEVPRT - CRTPSFCFG Configuring PSF with CRTDEVPRT on V4R2 Note: Where the text says , you should write the name that you want to assign to your specific hp LaserJet printer with the EuroForm IPDS 100 DIMM.
PSF/400 AFP printing using TCP/IP A completed screen looks like this: Display Device Description Page 1 5716SS1 V4R2M0 981108 BLDRB1 04/04/02 10:02:53 Device description . . . . . . . . : DEVD Option . . . . . . . . . . . . . . : OPTION Category of device . . . . . . . . : Device class . . . . . . . . . . . : DEVCLS Device type. . . . . . . . . . . . : TYPE Device model . . . . . . . . . . . : MODEL LAN attachment . . . . . . . . . . : LANATTACH User-defined object. . . . . . . . : USRDFNOBJ Library. . . .
EuroForm IPDS 100 User Guide A completed screen looks like this: PSF Configuration Information PSF configuration . . . . . . Library . . . . . . . . . . . User resource library . . . . IPDS pass through . . . . . . Activate release timer. . . . Release timer . . . . . . . . Restart timer . . . . . . . . SNA retry count . . . . . . . Delay time between retries. . Blank page. . . . . . . . . . Page size control . . . . . . Resident fonts. . . . . . . . Resource retention. . . . . . Edge orient . . . . . . .
PSF/400 AFP printing using TCP/IP AS/400 settings for version 4.3 To configure IPDS printing on OS/400 V4R3, you must use two commands: - CRTDEVPRT - CRTPSFCFG Configuring PSF with CRTDEVPRT on V4R3 Note: Where the text says , you should write the name that you want to assign to your specific hp LaserJet printer with the EuroForm IPDS 100 DIMM.
EuroForm IPDS 100 User Guide A completed screen looks like this: Display Device Description Page 1 5716SS1 V4R3M0 981108 BLDRB1 04/04/02 10:27:14 Device description . . . . . . . . : DEVD Option . . . . . . . . . . . . . . : OPTION Category of device . . . . . . . . : Device class . . . . . . . . . . . : DEVCLS Device type. . . . . . . . . . . . : TYPE Device model . . . . . . . . . . . : MODEL LAN attachment . . . . . . . . . . : LANATTACH User-defined object. . . . . . . . : USRDFNOBJ Library. . . . . . .
PSF/400 AFP printing using TCP/IP A completed screen looks like this: PSF Configuration Information PSF configuration . . . . . . Library . . . . . . . . . . . User resource library . . . . IPDS pass through . . . . . . Activate release timer. . . . Release timer . . . . . . . . Restart timer . . . . . . . . SNA retry count . . . . . . . Delay time between retries. . Blank page. . . . . . . . . . Page size control . . . . . . Resident fonts. . . . . . . . Resource retention. . . . . . Edge orient . . . . .
EuroForm IPDS 100 User Guide AS/400 settings for version 4.4, 4.5 and 5.1 To configure IPDS printing on OS/400 V4R4, V4R5 and V5R1, you must use two commands: - CRTDEVPRT - CRTPSFCFG Configuring PSF with CRTDEVPRT on V4R4 Note: Where the text says , you should write the name that you want to assign to your specific hp LaserJet printer with the EuroForm IPDS 100 DIMM.
PSF/400 AFP printing using TCP/IP A completed screen looks like this: Display Device Description Page 1 5716SS1 V4R4M0 981108 BLDRB1 04/04/02 10:02:47 Device description . . . . . . . . : DEVD Option . . . . . . . . . . . . . . : OPTION Category of device . . . . . . . . : Device class . . . . . . . . . . . : DEVCLS Device type. . . . . . . . . . . . : TYPE Device model . . . . . . . . . . . : MODEL LAN attachment . . . . . . . . . . : LANATTACH User-defined object. . . . . . . . : USRDFNOBJ Library. . . .
EuroForm IPDS 100 User Guide A completed screen looks like this: PSF Configuration Information PSF configuration . . . . . . Library . . . . . . . . . . . User resource library . . . . IPDS pass through . . . . . . Activate release timer. . . . Release timer . . . . . . . . Restart timer . . . . . . . . SNA retry count . . . . . . . Delay time between retries. . Blank page. . . . . . . . . . Page size control . . . . . . Resident fonts. . . . . . . . Resource retention. . . . . . Edge orient . . . . . . . .
Troubleshooting Troubleshooting If you have any questions or problems in connection with the EuroForm IPDS 100 DIMM please contact your supplier or alternatively use one of the methods described below. Please use the checklist below to make sure that the configuration of the IPDS 100 DIMM and the IBM host system is correct. 1) Check timers and port numbers. Make sure that the following parameters in the printer are set this way: a) Set the I/O Timeout to 60 seconds.
EuroForm IPDS 100 User Guide 5) Check the complete host configuration. Please refer to either the section “PSF/MVS AFP printing using TCP/IP” or the section “PSF/400 AFP printing using TCP/IP” in this manual. 6) If your problem is related to wrong text, wrong font, missing text, text not positioned correct, missing pages etc. then you can make a data stream trace using the build-in IPDS 100 Debug Tracer. Please see the section “Diagnostic Tool” in this manual for further details.
Troubleshooting Tools and Documentation We have designed a variety of informative tools to assist you with training and troubleshooting. You can locate these tools at http://www.euroform.
EuroForm IPDS 100 User Guide Appendix A. Technical Specifications IPDS Printer Emulation IBM 3812/16 IBM 4028 IBM 3112/16 IBM Network Printers 12, 17, 24 IBM InfoPrint 21, 32, 40 Resident IPDS Fonts IBM 4028 Compatibility Font Set IBM Core Interchange Font Set IBM Coordinated Font Set Network Attachment HP JetDirect 610N Internal Print Server P/N J4169A (Firmware version L.20.14 or later) HP JetDirect 615N Internal Print Server P/N J6057A (Firmware version L.22.
Appendix A.
EuroForm IPDS 100 User Guide Appendix B. Font and Code Page Information The EuroForm IPDS 100 supports outline fonts from both the IBM Core Interchange Font Set and the IBM Coordinated Font Set as resident fonts. In addition, a selection of these fonts is grouped into the 4028 Compatibility Font set. This set is used to represent the 4028 base internal raster fonts for limited compatibility.
Appendix B.
EuroForm IPDS 100 User Guide Typeface Times New Roman FGID GCSGID Font Width 2310 1300 Scalable 2311 1300 Scalable 2304 1300 Scalable 2305 1300 Scalable 2306 1300 Scalable Helvetica Italic Bold 2307 1300 Scalable Courier Roman 416 1300 Scalable Italic Medium Times New Roman Italic Bold Helvetica Roman Medium Helvetica Roman Bold Helvetica Italic Medium Medium Courier Roman Bold 420 1300 Scalable Courier Italic 424 1300 Scalable 1300 Scalable 2308 1264 Scalable 2309
Appendix B.
EuroForm IPDS 100 User Guide GCSGID Subsets Table 2 provides a mapping of the valid subsets of the GCSGIDs listed for the IBM Core Interchange fonts.
Appendix B.
EuroForm IPDS 100 User Guide Code Page Global ID Graphic Character Set ID (CPGID) (GCSGID) 1149 695 Language Supported Iceland Latin 1 Country Extended Code Pages with Euro Character 361 1145 Multinational, Belgium French, Belgium Dutch, Swiss French, Swiss German, Swiss Italian 382 1145 German 383 1145 Belgian 384 1145 Brazilian Portuguese 385 1145 Canadian French 386 1145 Danish, Norwegian 387 1145 Finnish, Swedish 388 1145 French, Catalan 389 1145 Italian 390 1145 Jap
Appendix B.
EuroForm IPDS 100 User Guide Code Page Global ID Graphic Character Set ID (CPGID) (GCSGID) Language Supported 1029 1154 Arabic Extended ISO/ASCII 1046 1177 Arabic Extended ISO/ASCII 8 Bit 8 Bit 1039 1258 GML List Symbols Hebrew EBCDIC and ASCII Code Pages 916 941 Hebrew ISO/ASCII 8 Bit 1028 1199 1028 1199 Hebrew 424 941 Hebrew 803 1147 Hebrew Character Set A 856 986 Hebrew PC (Primary = 862) Publishing (Primary = 424) 862 992 Hebrew PC 1039 1258 GML List Symbols Symbols 259
Appendix B. Font and Code Page Information Notes: 1. Prestige fonts used with code pages with a CPGID of 259 are mapped to the Courier Roman Medium Symbols font (FGID 416 GCSGID 1275) as shown in Table 1 on page 75. When the printer is in Box-Draw mode, any font, which does not indicate CPGID 259 support, will print with the Roman Medium Symbols font in a point size of 10 (12 pitch) when used with Code Page 259. This emulates 4028 behaviour. 2.
EuroForm IPDS 100 User Guide Typeface FGID Alt Pitch FGID Courier Point Font Code Size Width Pages 108 12 10 120 A, B 18 10 12 144 A, B 92 12 10 120 A, B 281 20 7.5 72 A, B OCR A 19 10 12 144 892 OCR B 03 10 12 144 893 Prestige 12 10 12 144 259, A, B 86 12 10 120 259, A, B Bold Courier Italic Courier Italic Letter Gothic Pica Prestige Elite Prestige 221 15 9 96 A, B Prestige 256 17.1 8.
Appendix B.
EuroForm IPDS 100 User Guide Code Page Global ID (CPGID) Graphic Character Set ID (GCSGID) 276 277 286 317 287 321 288 325 1002 1132 437 919 850 980 858 988 1003 1133 Group B 256 (Replaced by 500) 337 289 (Replaced by 500, but missing obsolete 329 “Peseta” character) Miscellaneous 310 963 259 340 892 968 893 969 1303 (Used internally for resident Code 128 n/a barcode font and postal bar code font support) Table 5.
Appendix B. Font and Code Page Information GCSGID Subsets Table 8 provides a mapping of the valid subsets of the GCSGIDs listed for the PSC Strategic Font Set 2.
EuroForm IPDS 100 User Guide 1304 0380, 0963, 1113 2039 0101, 0103, 0119, 0251, 0265, 0269, 0273, 0277, 0281, 0285, 0288, 0289, 0293, 0297, 0301, 0305, 0309, 0313, 0317, 0321, 0325, 0329, 0337, 0341, 0611, 0697, 0919, 0980, 0990, 0991, 0993, 0995, 1132, 1133, 1145, 1146, 1149, 1198, 1220, 1258, 1259, 1260 1306 0332, 1164, 1172, 1187 2041 0695, 0988, 1353, 1412, 2039 Table 8.
Appendix C. Related Publication Appendix C.
EuroForm IPDS 100 User Guide Appendix D. Glossary AFP Advanced Function Presentation or Printing. Duplex Pertaining to printing on both sides of a sheet of paper. Contrast with simplex. IPDS IBM’s Intelligent Printer Data Stream. Port In TCP/IP, a 16-bit number used to communicate between TCP and a higher-level protocol or application. Some protocols, such as the File Transfer Protocol (FTP) and the Simple Mail Transfer Protocol (SMTP), use the same port number in all TCP/IP implementations.