User manual

ManualsBrandsEuroLite Manualsaudio & home theatreLED Bar 2 RGBA 252/10

00058952.DOC, Version 1.2

15/26

USER MANUAL

LED Bar 2 RGBA 252/10

CAUTION!

Keepthisdeviceawayfromrainandmoisture!

Neveropenthehousing!

For your own safety, please read this user manual carefully before you initially start-up.

Every person involved with the installation, operation and maintenance of this device has to

- be qualified

- follow the instructions of this manual

- consider this manual to be part of the total product

- keep this manual for the entire service life of the product

- pass this manual on to every further owner or user of the product

- download the latest version of the user manual from the Internet

INTRODUCTION

Thank you for having chosen a EUROLITE LED Bar 2 RGBA 252/10. If you follow the instructions given in

this manual, we are sure that you will enjoy this device for a long period of time.

Delivery includes

1 Device

1 User manual

Unpack your device.

SAFETY INSTRUCTIONS

CAUTION!

Becarefulwithyouroperations.Withadangerousvoltageyoucansufferadangerous

electricshockwhentouchingthewires!

This device has left our premises in absolutely perfect condition. In order to maintain this condition and to

ensure a safe operation, it is absolutely necessary for the user to follow the safety instructions and warning

notes written in this user manual.

Important:

Damages caused by the disregard of this user manual are not subject to warranty. The dealer

will not accept liability for any resulting defects or problems.

Summary of content (12 pages)

PAGE 1
USER MANUAL LED Bar 2 RGBA 252/10 CAUTION! Keep this device away from rain and moisture! Never open the housing! For your own safety, please read this user manual carefully before you initially start-up.
PAGE 2
If the device has been exposed to drastic temperature fluctuation (e.g. after transportation), do not switch it on immediately. The arising condensation water might damage your device. Leave the device switched off until it has reached room temperature. Please make sure that there are no obvious transport damages. Should you notice any damages on the A/C connection cable or on the casing, do not take the device into operation and immediately consult your local dealer.
PAGE 3
OPERATING DETERMINATIONS This device is a lighting effect for creating decorative effects. This product is only allowed to be operated with an alternating voltage of 230 V, 50 Hz and was designed for indoor use only. This device is designed for professional use, e.g. on stages, in discotheques, theatres etc. Lighting effects are not designed for permanent operation. Consistent operation breaks will ensure that the device will serve you for a long time without defects. Do not shake the device.
PAGE 4
DESCRIPTION OF THE DEVICE 1 2 (1) Fixation screw (2) Mounting bracket Power OUT Power supply: 230 V AC, 50 Hz~ Fuse: F 1 A, 250V 3 4 5 6 7 8 6 9 (3) Fuseholder (4) Power supply (5) DMX-In socket (6) Programming buttons (7) Display (8) DMX-Out socket (9) Power Out INSTALLATION The LED Bar 2 RGBA 252/10 can be installed on the ground or on the wall or ceiling.
PAGE 5
The operator has to make sure that safety-relating and machine-technical installations are approved by an expert after every four year in the course of an acceptance test. The operator has to make sure that safety-relating and machine-technical installations are approved by a skilled person once a year. Procedure: The device should be installed outside areas where persons may walk by or be seated.
PAGE 6
Attachment Before attaching the device, make sure that the installation area can hold a minimum point load of 10 times the device's weight. The device must only be installed absolutely planar at a vibration-free, oscillation-free and fire-resistant location. Make sure that the device is installed absolutely planar by using a water-level. The device must be installed out of the reach of people. The device must always be installed via all fixation holes.
PAGE 7
Building a serial DMX chain: Connect the DMX output of the first device in the DMX chain with the DMX input of the next device. Always connect one output with the input of the next device until all devices are connected. Caution: At the last fixture, the DMX-cable has to be terminated. Plug the terminator with a 120 resistor between Signal (–) and Signal (+) in the DMX-output of the last fixture. Connection between devices On the rear panel, there is an IEC socket (Power Out).
PAGE 8
Stand Alone-Mode Chaser A chaser is a sequence of different steps that will be called up one after another in a continuous loop. With the LED Bar 2 RGBA 252/10, you can select up to 13 different chasers. Selecting a chaser Press the MODE button to select the internal program mode. Select the desired chaser (01 – 13) via the UP or DOWN buttons (see following graphic). Press the ENTER button to select speed and flash settings, respectively. You can select the desired values via the UP or DOWN buttons.
PAGE 9
Controlling: After having addressed the LED Bar 2 RGBA 252/10, you may now start operating it via your lighting controller. Note: It’s necessary to insert the XLR termination plug (with 120 Ohm) in the last lighting in the link in order to ensure proper transmission on the DMX data link. Addressing Press the MODE button until the display shows DMX512 MODE. Press the ENTER button and the display shows: 001. Set the desired address via the UP or DOWN buttons.
PAGE 10
19-Channel Mode: (Default) CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8 CH9 CH10 CH11 CH12 CH13 CH14 CH15 CH16 CH17 CH18 CH19 0-5 Blackout 6-10 Dimmer 11-15 Dimmer 0-255 0-255 0-255 0-255 0-255 0-255 0-255 0-255 0-255 0-255 0-255 0-255 0-255 0-255 0-255 0-255 0-255 0-255 0-255 0-255 All Dimm Flash All Dimm Flash 16-20 R Dimmer Flash 21-25 G Dimmer Flash 26-30 B Dimmer Flash 31-35 A Dimmer Flash 36-40 RA Dimmer Flash 41-45 RG Dimmer Flash 46-50 RB Dimmer Flash 51-55 GB Dimmer Flash 56-60 AB Dim
PAGE 11
Master/Slave Mode The master/slave-operation enables that several devices can be synchronized and controlled by one masterdevice. On the rear panel of the LED Bar 2 RGBA 252/10 you can find an XLR-jack and an XLR-plug, which can be used for connecting several devices. This device then works as master-device and controls the slave-devices, which are to be connected to the master-device via a stereo shielded cable. Connect the OUT-jack with the IN-plug of the next device.
PAGE 12
Should you have further questions, please contact your dealer. TECHNICAL SPECIFICATIONS Articles: Power supply: Power consumption: Number of DMX channels: DMX-512 connection: Sound-control: Maximum ambient temperature Ta: Maximum housing temperature TB: Min. distance from flammable surfaces: Min. distance to lighted object: Fuse: Number of 10mm LEDs: Beam angle: Dimensions: Weight: 51930418/51930443 230 V AC, 50 Hz ~ 41 W 4/6/19 3-pin XLR via built-in microphone 45° C 50° C 0.5 m 0.