6kg Condenser Clothes Dryer Manual MODEL COND6KG Installation and Operation
Read this manual prior to initial operation of the product! Dear Customer, We hope that your product, which has been manufactured in modern facilities and passed through a strict quality control procedure, will give you very good results. We advise you to read through this manual carefully before using your product and keep it for future reference. This User Manual will • Help you use your machine in a fast and safe way. • Read the User Manual before installing and starting your product.
1 Important safety information This section includes safety information that will help protection from risks of personal injuries or materialistic damages. Failure to follow these instructions shall cause any warranty and reliability commitment to become void. General safety • • • • • • • • • • • • • • • • Never place the machine on a carpetcovered floor, otherwise, lack of airflow beneath the machine may cause electrical parts to overheat. This will cause problems with your machine.
• • • • • • • • • • • water! There is the risk of electric shock! Always disconnect by unplugging from the mains before cleaning. Never touch the plug with wet hands. Never unplug by pulling on the cable, always pull out by grabbing the plug only. Do not operate the machine if the power cable or plug is damaged! Never attempt to repair the machine yourself, otherwise, you will be putting your life and others’ lives in danger.
2 Installation Refer to the nearest Authorised Service Agent for installation of your product. CPreparation of location and electrical installation for the product is under customer’s responsibility. BInstallation and electrical connections must be carried out by a qualified personnel. APrior to installation, visually check if the product has any defects on it. If so, do not have it installed. Damaged products will cause risks for your safety.
Disposing of the old machine cables or multi-plugs. The main fuse and switches must have a contact distance of minimum 3 mm. BDamaged power cable must only be replaced by a qualified electrician. BIf the product is faulty, it must not be operated unless it is repaired! There is the risk of electric shock! • First use • • To have the product ready for operation before calling the authorised service agent, make sure that its location and power supply installations are appropriate.
3 Initial preparations for drying Things to be done for energy saving: • Make sure that you operate the product • • • • • • • • • • • at its full capacity but pay attention to not exceeding it. Spin your laundry at the highest speed possible when washing them. Thus, the drying time is shortened and energy consumption is decreased. Pay attention to dry same types of laundry together. Follow the instructions in the user manual for programme selection.
• • foam (latex foam), shower bonnets, water resistant textiles, materials with rubber reinforcement and rubber foam pads should not be dried in the dryer. Do not use fabric softeners and anti-static products unless they are recommended by the manufacturers of the fabric softener or the product. Do not dry the underwear reinforced with metal parts in the dryer. If these metal reinforcements loosen and break during drying, they will damage your dryer.
4 Selecting a Program and Operating Your Machine Control panel 1 2 3 4 Synthetics Ready to Iron Ready to Wear Timer Programmes 10 min Clean Filter Start/ Pause Drying Ready to Iron Ready to Wear Water Tank Full End/Anticreasing 7 Cancel 3 sec. Cottons Ready to Wear Ready to Iron 20 min 40 min Buzzer Cancel Extra Dry On/Off Delicates 60 min 6 Freshen Up 5 1. Filter cleaning warning light Warning light turns on when the filter is full. 2.
Preparing the machine 1. Plug in your machine. 2. Place the laundry in the machine. 3. Press the “On/Off” button. C Pressing the “On/Off” button does not necessarily mean that the programme has started. Press "Start/Pause/Cancel" button of the machine to start the programme. Program selection Decide the appropriate program from the table below which includes drying temperature in degrees. Select the desired program with the program selection button.
restart the machine, please drain the water in the water tank. Press “Start/Pause/Cancel” button to start the programme after you have emptied the water tank. The warning LED goes off and the programme resumes operating. Starting the Programme 1. Press “Start/Pause/Cancel” button to start the programme. 2. “Start/Pause/Cancel” button will light up to indicate that the programme has started. Progress of programme Progress of a running programme is shown through the programme follow-up indicator.
Ending the programe through canceling The programme which is selected first will keep on going even if the position of the programme selection button is changed. A new programme can be selected and started after “Programme cancel” is activated in order to change the drying programme. To cancel any selected programme; • Press “Start/Pause/Cancel” button for about a duration of 3 seconds.
5 Maintenance and cleaning Lint filter Lint and fibres released from the laundry to the air during the drying cycle are collected in the “Lint Filter”. dampened with vinegar and dry them. CClean metal sensors 4 times a year. ANever use solvents, cleaning agents or similar substances when cleaning since these materials can cause fire and explosion! Water tank (Products equipped with a condenser); CSuch fibre and lint are generally formed during wearing and washing.
For the condenser (products with a condenser) Hot and humid air in the condenser is cooled with the cold air from the room. Thus, the humid air circulating in your dryer is condensed and then pumped into the tank. CClean the condenser after every 30 drying cycles or once a month. To clean the condenser: 1. If a drying process has been carried out, open the door of the product and wait until it cools down. 2. Unlock the 4 condenser locks after opening the kick plate. 3. Pull out the condenser. 4.
6 Solution suggestions for problems Drying process takes too much time • Meshes of the filter may be clogged. Wash with water. Laundry come out wet at the end of drying. • • Meshes of the filter may be clogged. Wash with water. Excessive laundry might have been loaded in. Do not overload the machine. Machine does not switch on or the program does not start. Machine is not activated when set. • It might have not been plugged in. Make sure that the machine is plugged in. • The loading door may be ajar.