900mm Island Canopy Manual MODEL ICF9BLS Installation and Operation
CANOPY INSTALLATION AND OPERATION MANUAL
Dear Customer, We thank you for choosing this quality appliance and hope you enjoy many years of reliable service. Please ensure this manual is read carefully before installation and use. Keep this manual in a safe and accessible location should future reference be required. Regards Home Appliances CONTENT 2……………………………………….Notice 3……………………………………….Feature 4………………………………………..Installation 6………………………………………..Notice of installation 6………………………………………..
NOTICE 1. Thank you for choosing our cooker hood. Please read the instruction manual carefully before use. 2. The installation work must be undertaken by a qualified and competent fitter. 3. The manufacturer disclaims all liability for any damage or injury caused as a result of not following instructions for installation contained in the following text. The cooker hood is used on 220/240v, 50Hz.
(2)FEATURE 1. The cooker hood uses high quality materials, and is made with a streamlined design. 2. Equipped with a large power low noise electric motor and centrifugal leaf, it produces strong suction, low noise, non stick grease filter and easy to clean. 3. Special wind tunnel construction and oil collector design, free dirt will be absorbed in a second.
(3) INSTALLATION 1. The ceiling must can bear at least 40kgs weight, and the thickness of the ceiling must be 30MM, see pic 2, drill 1*170mm round hole in the ceiling. 2.
5 5
(4) NOTICE OF INSTALLATION 1. Before installation, please ensure the area is clean to avoid suction of the remaining bits of broken wood and dust. 2. It cannot share the same air ventilation tube with other appliance such as gas tube, warmer tube, and hot wind tube. 3. The bending of ventilation tube should be≥120°, parallel or above the start point and should be connected to the external wall. 4. After installation, make sure that the extractor is level to avoid grease collection at one end.
(6) USE Electronic Button 1. Turn on the power; the buzzer will buzz five times. The sound shows that the appliance is powered. 2. Push the low button, the indicating light 1 on, the buzzer will buzz once, and the motor runs at low speed. Push it again and the motor will stop. 3. Push the middle button, the indicating light 2 on, the buzzer will buzz once, and the motor runs at mid speed. Push it again and the motor will stop 4.
Push button 1. Push stop button, and the motor will stop. 2. Push the Low button, the buzzer will buzz once, and the motor runs at low speed. 3. Push the Mid button, the buzzer will buzz once, and the motor runs at mid speed. 4. Push the High button, the buzzer will buzz once, and the motor runs at high speed. 5. Push the light button and the two lights will come on. Push it again and the light will turn off.
LCD Electronic button Pic 7 1. Plug the hood; LCD will display 24-hour system with blue backlight. Backlight will be extinguished after 30 seconds without any operation. 2. Press “ “ ” button again; lights will be off and “ 3. Press “ “ ” button once; lights will be on and LCD will show “ ” on LCD will disappear. ” button once; the hood works at LOW speed and LCD will show ” and “ ” button will be on. Press “ works at MEDIUM speed. Press “ works at HIGH speed.
pressing “ ” button. Press “ ” button once; the number reduces by 01. When LCD shows 00; it doesn’t work by pressing “ ” button. After setting hour; you can start setting minute by pressing “ ” button again. on LCD flashes; which represents minutes. Press “ the number adds by 01. Continue pressing “ ” button once ” button; it will display from 01;02… until 59. When LCD shows 59; it doesn’t work by pressing “ button. Press “ ” button once; the number reduces by 01.
LCD Touch control Pic 8 1. Power on: Switch on the power supply, and the backlight is lit, displaying “24-hour system”. The output is then blocked up,and the soot machine enters standby status. The backlight disappear automatically 30 seconds later under the condition of none operation. 2. Press “Indicator” key: Press the indicator key once, the indicator is lit, and on the LCD screen is lit.
Long press timer key for 2-3 seconds, time segment , and the first two hour bit segment flash, use key for the digit increase, and use key for the digit decrease. Namely: The variable is 01 each time it is pressed; the hour segment is with the largest digit of 23. If it exceeds 23, key is null and void. If it is equal to 00, then, the key is null and void.
(7) MAINTENANCE 7.1 The cleaning of the carbon grease filter mesh The filter mesh is made of high-density stainless steel. Please do not use the corrosive detergent on it. Keeping this filter clean will keep the appliance running correctly. Please strictly follow the guidelines below. Method 1: Put the mesh into 40-50 c clean water, pour on detergent, and soak for 2-3 mins. Wear gloves and clean with a soft brush. Please do not apply too much pressure, as the mesh is delicate and will damage easy.
G. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard. (8) ABNORMITY AND SOLUTION 8.1 LED light replacing Remove the filters, and push the light downwards, and unplug the wiring connector.
8.
The hanging screw not tight enough Tighten the hanging screw and make it horizontal