User Manual Off Board Undercupboard Rangehood INLU90
Product / Installer details For future reference we suggest that you staple a copy of your purchase receipt here and complete the below so the information is always at hand.
Dear Customer, Congratulations on the purchase of your new product from Home Appliances Pty Ltd. We recommend you please take some time to read the instruction manual thoroughly to familiarise yourself with the functionality and operations to ensure optimum performance of your new appliance. After reading the manual, please store it in a safe and accessible location for future reference.
Contents Notice 1 Safety Warnings 2 Caution 3 Features 4 Schematic Diagram 5 Installation 6 Operation 9 Maintenance 10 Bulb Replacement 11 Troubleshooting and Possible Solutions 12 Supplied Accessories 13 HAPL Ducting Kit Solutions 14
Notice 1. Thank you for choosing your Euromaid Off-Board Canopy Rangehood. Please read the instruction manual carefully before use. 2. The installation work must be undertaken by a qualified and competent installer. 3. The manufacturer disclaims all liability for any damage or injury caused as a result of not following the instructions for the installation and or operation contained within this instruction manual. 4. The Rangehood operates on 220/240V, 50Hz.
Safety Warnings • Please ensure that children do not use the Rangehood. • Your Rangehood is for domestic use only, not suitable to be used with barbeque, or any commercial applications. • Any installation work must be carried out by a trained qualified electrician and or an experienced installer. • The Rangehood and its filter mesh should be cleaned regularly to keep them in good working order. • Before cleaning your Rangehood, please always ensure that the power has been switched off.
Caution • Exhaust air must be discharged in accordance with the local regulations, it is recommended that a suitable ducting kit should be used. • Accessible parts may become hot when used with cooking appliances.
Features • This Rangehood is designed to reduce the noise level within the kitchen by utilising a separate fan motor that is positioned in the roof cavity of your home. The motor is designed to be fixed in a suitable and secure position. • This Rangehood uses high quality materials, Stainless steel construction with easy to operate controls and is made with a streamlined design. • Equipped with a large power low noise electric motor and centrifugal fan, it produces strong suction and low noise.
Schematic Diagram 1. The main body and the external motor are connected by the supplied 4 metre extension cable. A separate cable is plugged into the power. 2. The supplied 3 metre extension ducting will connect the main body and external motor, and cooking residues will be extracted and discharged to outside via a ducting kit.
Installation The Rangehood should be placed at 65 - 75cm from the cooking surface for the best effect. See Pic 1 1. Cut the required size hole in the underside of the cabinet for the hood body 2. Detach the front panel by unscrewing the 2 screws (M4 x 10mm) see below diagram 3.
Installation (continued) 4. Install the 150mm outlet by (ST4*8mm) screws, and attach the extension ducting pipe. 5. Connect the power cord on main body with extend wiring 6. Fix the left and right support bracket on the side of external motor, by using 6 pcs (ST4*8mm) screws 7.
Important points to consider for installation 1. The location of the fan unit shall allow access for maintenance and repair. Permanent fixed means of access is required where the fan unit location is beyond the extent of normal steps or ladders. 2. Before installation, please ensure the area is clean to avoid suction of the remaining bits of debris and dust. 3.
Operation 1. Push the low button, the indicating light on, and the motor runs at low speed. Push it again and the motor will stop. 2. Push the middle button, the indicating light on, and the motor runs at mid speed. Push it again and the motor will stop 3. Push the high button, the indicating light on, and motor runs on high speed. Push it again and the motor will stop 4. Push the light button; the indicating light on, and the two lighting lamps will come on. Push it again and the lamps will turn off.
Maintenance Cleaning and Maintenance: Changing and cleaning the anti-grease filters • Remove the filters as per shown below. • You can clean the filter using the following methods. –– Soak them for about 3 minutes in hot water (40-50 degrees) with a grease-loosening detergent then brush it gently with a soft brush. To avoid damaging the filter, please do not apply too much pressure. –– It can be put into a dishwasher with detergent, set the temperature at around 45 degrees.
Bulb Replacement 1. Firstly, switch the unit off at the power and pull out the plug. 2. Wait until the light bulb is cooled down before replacement. 3. Replace with the same type of bulb by pushing the bulb slightly and screwing in or out. Please note: Alternatively, you can change the bulb from the inside of the Rangehood, take out the metal filter and have the bulb replacement from inside of the Rangehood.
Troubleshooting and Possible Solutions Fault Light on, but motor does not work Light does not work, motor does not work Oil leakage Vibration of the body Insufficient suction Cause Solution The fan blocked Service call to clear the blockage The capacitor damaged Service call to replace capacitor The motor jammed bearing damaged Service call to replace motor A electrical or burning smell from the motor Service call to replace motor Beside the above mentioned, check the following: Light damaged
Supplied Accessories Part picture QTY - hood body QTY - motor Wall plug Nil 4 Screw (4mm x 14mm) 8 Nil Screw (4mm x 30mm) Nil 4 Screw (4mm x 8mm) 4 10 Outlet 1 2 Butterfly flap Nil 2 INLU90 Off Board Undercupboard Rangehood User Manual Page 13
HAPL Ducting Kit Solutions The ducting kit connects to the outlet of the external roof cavity fan motor. There is a ducting solution available for most installations. Please ensure you have selected the correct kit for your requirements. The HAPL ducting kits include all parts required to complete off-board Rangehood installation.
For all product enquiries (including warranty support), please contact our Customer Care team on 1800 444 357 or via email: customercare@hapl.com.
